SEARCH · Engineering Papers
Results for “MORTARS”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Adaptive Multiscale Modeling Using Generalized Mortar Methods.
Abstract not provided.
Methods of mechanical contact constraint enforcement using the mortar finite element method
Explore the source record for details and available documents.
Low Level Radioactive Wastes Conditioning during Decommissioning of Salaspils Research Reactor
The decommissioning of Salaspils research reactor is connected with the treatment of 2200 tons different materials. The largest part of all materials ({approx}60 % of all dismantled materials) is connected with low level radioactive wastes conditioning activities. Dismantled radioactive materials were cemented in concrete containers using water-cement mortar. According to elaborated technology, the tritiated water (150 tons of liquid wastes from special canalization tanks) was used for preparation of water-cement mortar. Such approach excludes the emissions of tritiated water into environment and increases the efficiency of radioactive wastes management system for decommissioning of Salaspils research reactor. The Environmental Impact Assessment studies for Salaspils research reactor decommissioning (2004) and for upgrade of repository 'Radons' for decommissioning purposes (2005) induced the investigations of radionuclides release parameters from cemented radioactive waste packages. These data were necessary for implementation of quality assurance demands during conditioning of radioactive wastes and for safety assessment modeling for institutional control period during 300 years. Experimental studies indicated, that during solidification of water- cement samples proceeds the increase of temperature up to 81 deg. C. It is unpleasant phenomena since it can result in damage of concrete container due to expansion differences for mortar and concrete walls. Another unpleasant factor is connected with the formation of bubbles and cavities in the mortar structure which can reduce the mechanical stability of samples and increase the release of radionuclides from solidified cement matrix. The several additives, fly ash and PENETRON were used for decrease of solidification temperature. It was found, that addition of fly ash to the cement-water mortar can reduce the solidification temperature up to 62 deg. C. Addition of PENETRON results in increasing of solidification temperature up to 83 deg. C. Experimental data shows, that water/cement ratio significantly influences on water-cement mortar's viscosity and solidified samples mechanical stability. Increasing of water ratio from 0.45 up to 0.65 decreases water-cement mortar's viscosity from 1100 mPas up to 90 mPas. Significant reduction of viscosity is an important factor, which facilitates the fulfillment all gaps and cavities with the mortar during conditioning of solid radioactive wastes in containers. On the other hand, increase water ratio from 0.45 up to 0.65 decreases mechanical stability of water-cement samples from 23 N/mm{sup 2} to the 12 N/mm{sup 2}. It means that water-cement bulk stability significantly decreases with increasing of water content. Technologically is important to increase the tritiated water content in container with cemented radioactive wastes. It gives a possibility to increase the fulfillment of container with radioactive materials. On the other hand, additional water significantly reduces bulk stability of containers with cemented radioactive wastes, which can result in disintegration of radioactive wastes packages in repository during 300 years. Taking into account the experimental results, it is not recommended to exceed the water/cement ratio more than 0.60. Tritium and Cs{sup 137} leakage tests show, that radionuclides release curves has a complicate structure. Experimental results indicated that addition of fly ash result in facilitation of tritium and cesium release in water phase. This is unpleasant factor, which significantly decreases the safety of disposed radioactive wastes. Despite the positive impact on solidification temperature drop, the addition of fly ash to the cement-water mortar is not recommended in case of cementation of radionuclides in concrete containers. In conclusion: The cementation processes of solid radioactive wastes in concrete containers were investigated. The influence of additives on cementation processes was studied. It was shown, that the increasing of water ratio from 0.45 up to 0.65 decreases water-cement mortar's viscosity more than 10 times. Mechanical stability of samples decreases 2 times, which reduces the bulk stability of cemented radioactive wastes package. It is not recommended to increase water ratio more than 0.60 in cement-water mortar. Addition of flay ash to the water-cement mortar decreases the solidification temperature from 83 deg. C to 62 deg. C. However, it was found, that the addition of fly ash to the water-cement mortar facilitate the radionuclides leakage from solidified water-cement matrix. Therefore fly ash is not recommended for radioactive wastes cementation. It was shown that tritiated water can be used for cementation of solid radioactive wastes in concrete containers.
Experimental evidence of a moisture clog effect in cement-based materials under temperature
This study is an original contribution to the understanding of the hydraulic behaviour of cement-based materials when subjected to temperature rises. Permeability is measured continuously during heating by injecting inert gas into a sample at homogeneous temperature. Using a confining cell especially designed in our laboratory, the sample is submitted to a constant heating rate, up to 200 deg. C, superimposed to hydrostatic pressure (at ca. 5 MPa). In parallel with a normalised CEM II mortar (water-to-cement ratio (W/C) of 0.5), a CEM V-cement-based concrete, used in nuclear waste storage applications, is studied. For normalised mortar, gas retention is evidenced, depending on the sample size (scale effect), water saturation level S{sub w}, and heating rate. For dry normalised mortar, permeability may be divided by two during heating. In conjunction with thermo-gravimetry analysis (TGA) results, such evolution is attributed to the dehydration of C-S-H around 150 deg. C. Indeed, mass loss after heat cycling is substantially higher than that due to free water release solely: mortar loses structural, bound water during the process. For partially-saturated and long mortar samples, a gas retention phenomenon is recorded when heating at a rate of ca. 4.9 deg. C/min. Our analysis is that free water inside the macropores, as well as bound water released from the C-S-H, dilates or vaporizes, and obstructs the interconnected porous network. Due to moisture clogging, no more gas is allowed through the material pore network: a so-called gas retention phenomenon occurs. Most interestingly, although loosing structural water like normalised mortar, yet over a wider temperature range, dry CEM V concrete displays good temperature resistance, as its permeability remains constant during heating. For highly partially-saturated concrete, a gas retention effect is recorded. As a conclusion, observed phenomena at the laboratory scale testify of potentially strong gas retention effects upon engineering structures subjected to temperature gradients over time. Indeed, quite low temperature rises (and heating rates) are able to induce moisture clogging inside partially-saturated materials. It is also concluded that cement-based material composition, i.e. bound water release ability, is influential in gas transport phenomena under temperature.
An investigation on the use of shredded waste PET bottles as aggregate in lightweight concrete
In this work, the utilization of shredded waste Poly-ethylene Terephthalate (PET) bottle granules as a lightweight aggregate in mortar was investigated. Investigation was carried out on two groups of mortar samples, one made with only PET aggregates and, second made with PET and sand aggregates together. Additionally, blast-furnace slag was also used as the replacement of cement on mass basis at the replacement ratio of 50% to reduce the amount of cement used and provide savings. The water-binder (w/b) ratio and PET-binder (PET/b) ratio used in the mixtures were 0.45 and 0.50, respectively. The size of shredded PET granules used in the preparation of mortar mixtures were between 0 and 4 mm. The results of the laboratory study and testing carried out showed that mortar containing only PET aggregate, mortar containing PET and sand aggregate, and mortars modified with slag as cement replacement can be drop into structural lightweight concrete category in terms of unit weight and strength properties. Therefore, it was concluded that there is a potential for the use of shredded waste PET granules as aggregate in the production of structural lightweight concrete. The use of shredded waste PET granules due to its low unit weight reduces the unit weight of concrete which results in a reduction in the death weight of a structural concrete member of a building. Reduction in the death weight of a building will help to reduce the seismic risk of the building since the earthquake forces linearly dependant on the dead-weight. Furthermore, it was also concluded that the use of industrial wastes such as PET granules and blast-furnace slag in concrete provides some advantages, i.e., reduction in the use of natural resources, disposal of wastes, prevention of environmental pollution, and energy saving.
Magnetic susceptibility and magnetic resonance measurements of the moisture content and hydration condition of a magnetic mixture material
We developed a magnetic measurement method to measure the moisture content and hydration condition of mortar as a magnetic mixture material. Mortar is a mixture of Portland cement, sand, and water, and these materials exhibit different magnetic properties. The magnetization–magnetic field curves of these components and of mortars with different moisture contents were measured, using a specially developed high-temperature-superconductor superconducting quantum interference device. Using the differences in magnetic characteristics, the moisture content of mortar was measured at the ferromagnetic saturation region over 250 mT. A correlation between magnetic susceptibility and moisture content was successfully established. After Portland cement and water are mixed, hydration begins. At the early stage of the hydration/gel, magnetization strength increased over time. To investigate the magnetization change, we measured the distribution between bound and free water in the mortar in the early stage by magnetic resonance imaging (MRI). The MRI results suggest that the amount of free water in mortar correlates with the change in magnetic susceptibility.
Damage development in neutron-irradiated concrete in a test reactor: Hygro-thermal and mechanical simulations
This paper reports the development of a 3D mesoscale hygro-thermal-mechanical simulation approach to predict damage in concrete irradiated in a test reactor. This framework, developed in MOOSE, considers the effects of elevated temperature, moisture content, and high neutron fluence (energy threshold, E > 0.1 MeV) on the mortar and aggregates separately. The first-stage simulation implements hygro-thermal analysis to determine the temperature and RH inside the specimen as a function of imposed radiation energy. These are used as inputs to the second stage, which considers radiation-induced volumetric expansion (RIVE) of aggregates, and creep, shrinkage, and stress-strain response of mortar to predict the expansion, stresses, and damage in specimens made using different coarse aggregates and subjected to different irradiation times. The irradiation time-dependent damage in the mortar is expressed using an isotropic damage parameter. This multi-physics model serves as a predictive tool for damage quantification in concrete due to neutron irradiation.
Technical Performance of Refractory Liners for Molten Chloride Salt Thermal Energy Storage Systems
A chloride-based molten-salt system that uses a ternary blend of MgCl2/KCl/NaCl is investigated to provide higher temperature thermal energy storage capability. Despite higher thermal stability, molten chlorides present several unique challenges, including the design of internal refractory-ceramic liners to prevent the corrosion and thermal stress of alloy tank shells. This work discusses issues and potential solutions related to containment of molten chloride salt, specifically the optimization of the refractory material at the molten salt interface (hot face). The down-selected hot face candidate limits permeation of salt through the material and forms a highly stable secondary surface phase in equilibrium with the molten salt. A mortar is created using the corrosion resistant hot face brick. Brick and mortar composite are subjected to mechanical stress/strain analysis, in order to calculate composite material properties and better inform thermomechanical models. The U.S. Department of Energy Generation 3 (DOE Gen3) program seeks to develop higher efficiency CSP plants that can provide cost-competitive, flexible power in the U.S. electric grid. The proposed Gen3 Liquid Pathway CSP plant closely resembles the configuration of current nitrate salt power towers with two-tank storage (Gen2). The differences between Gen2 and Gen3 include the types of compatible materials used in salt storage tank construction. Stainless steel loses strength at Gen3 temperatures, and although nickel superalloys would be capable of withstanding sustained high temperatures, these materials are prohibitively expensive at scale. Uninsulated tank shells also pose a significant risk as common steels are highly susceptible to chemical attack from molten chloride salt. To address these concerns, refractory-ceramic based containment materials are proposed to line the inside of the hot and cold storage tanks. In doing so, stainless or carbon steel shells may be used in construction depending on the level of insulation provided. The composition of the internal liner requires careful consideration to maximize the efficacy of multiple parameters including corrosion resistance, strength at operating temperature, durability, and cost. This is particularly true for the material at the interface with the salt, known as the "hot face", which is responsible for protecting the insulating layers between the tank shell and the hot face brick layer. The molten salt in this system is superheated over 300 °C above its freeze temperature. Therefore, unlike other industrial processes which use refractory-lined vessels, it is not expected that a freeze plane will develop in the hot face. Therefore, the hot face must be designed to withstand chemical corrosion and inhibit permeation of molten salt into the insulating layers. A down selection was performed to identify a hot face candidate best equipped to maintain thermal, mechanical, and chemical integrity when exposed to molten salt over extended periods of time. Long-duration chemical capability experiments were conducted with the down selected hot face refractory fully immersed in molten chloride salt for up to 3000 hours. The average salt penetration does not exceed 100 microns. When extrapolated to 20 and 30 years of continuous exposure, the expected salt penetration depth is approximately 2.0 mm and 2.9 mm, respectively. A magnesium-rich secondary phases develops at the salt/refractory interface. X-ray diffraction identifies the material as forsterite (Mg2SiO4), which is reported to form synthetically in molten chloride salt solutions. These results suggest the selected hot face will adequately inhibit salt permeation. While there is optimism that the hot face brick will inhibit salt permeation, mortar joints are typically the weakest point of a refractory brick liner. From a thermochemical perspective, differing thermal expansion coefficients may result in the mortar and brick to grow independent of each other, creating gaps through which molten salt can penetrate. To address this issue, NREL has developed an in-house mortar composed of the down selected hot face brick that has been shown to be compatible with the salt. Compressive stress/strain analyses have been performed on the brick/ mortar composites to generate stress/strain curves. Modulus of elasticity and Poisson's ratio of the composite may be calculated from the stress/strain curves, in order to provide more representative data to finite element mechanical models for accurate approximation of stress on the tank shell and the amount of thermal expansion expected within the tank liner.
Reactive powder based concretes: Mechanical properties, durability and hybrid use with OPC
The basic mechanical properties, frost durability and the bond strength with normal strength concretes of the ultra high strength (UHS) mortars and concretes were studied. The produced mixes had plastic or fluid-like consistency. The 28-day compressive strength varied between 170 and 202 MPa for the heat-treated specimens and between 130 and 150 MPa for the non-heat-treated specimens. The shrinkage values were two times higher for the UHS mortars in comparison with the UHS concretes. After the initial shrinkage, swelling was noticed in the UHS mortars. The lowest creep values were measured for the non-heat-treated UHS concretes. The frost-deicing salts durability of the UHS mortars and concretes appeared to be very good even despite the increased water uptake of the UHS concretes. The study of the hybrid concrete beams indicated the formation of low strength transition zone between the UHS mortar and normal strength concrete.
A discrete-continuum coupled finite element modelling approach for fibre reinforced concrete
Highlights: • An easy-to-implement but effective meso-scale modelling approach is developed for FRC. • It is capable of simulating and interpreting all main failure mechanisms in FRC. • It is critically validated by experiments with single or multiple random fibres under various loading conditions. • It can be used to optimise key design factors of FRC at meso/material scale by parametric studies. - Abstract: Fibre reinforced concrete (FRC) exhibits complicated failure modes such as fibre breakage, mortar cracking, crushing and spalling, fibre-mortar interfacial debonding, depending on many material properties, geometric dimensions, boundary and loading conditions. Most existing numerical models are unable to reproduce these failure modes that may occur simultaneously or sequentially in a specimen, mainly due to difficulties in generating finite element meshes with a large number of randomly-oriented fibres. Herein we develop a discrete-continuum coupled finite element modelling approach for FRC materials capable of effectively simulating all the major failure modes. The continuum damaged plasticity model is used to simulate damage and fracture behaviour of the mortar, while debonding of fibre-mortar interfaces is modelled by nonlinear cohesive interfacial elements. Unique techniques are devised to generate conforming meshes between fibres and the surrounding mortar so that the randomly-oriented fibres are easily modelled. The modelling approach is validated by simulating single fibre pullout tests with different inclination angles, notched and non-notched direct tensile tests and three-point bending beam tests with randomly-distributed multiple fibres.
Estimating viscoelastic compliance of desiccating cementitious materials using drying prism tests
Highlights: • Determining relative humidity and degree of reaction of desiccating cementitious materials via an integrated method • Extracting moisture diffusion coefficient of cement mortar using the mass loss data of the prism specimens • Estimating uniaxial viscoelastic compliance of cement mortar using the shrinkage strain data of the prism specimens An integrated modeling approach to determining internal relative humidity and degree of reaction of desiccating cementitious materials has been developed. By simultaneously accounting for both self-desiccation and external drying, the model is capable of predicting the evolution of material properties of desiccating cementitious materials. Using the mass loss data of the prism specimens, the moisture diffusion coefficient of a nonlinear model for cement mortar was determined. Additionally, a previous poroviscoelastic shrinkage model was modified and extended. Through comparison of predicted and measured axial strain of the prism specimens, the viscoelastic compliance of cement mortar was extracted. The present work revealed that it is possible to use a simple drying prism test to fit the moisture diffusion coefficient and creep compliance of cementitious materials, though the comparison of the extracted viscoelastic compliance with measured compliance was only reasonable if the outer layer of the drying mortar was presumed to have microcracking.
Bioinspired Nacre‐Like Alumina with a Metallic Nickel Compliant Phase Fabricated by Spark‐Plasma Sintering
Abstract Many natural materials present an ideal “recipe” for the development of future damage‐tolerant lightweight structural materials. One notable example is the brick‐and‐mortar structure of nacre, found in mollusk shells, which produces high‐toughness, bioinspired ceramics using polymeric mortars as a compliant phase. Theoretical modeling has predicted that use of metallic mortars could lead to even higher damage‐tolerance in these materials, although it is difficult to melt‐infiltrate metals into ceramic scaffolds as they cannot readily wet ceramics. To avoid this problem, an alternative (“bottom‐up”) approach to synthesize “nacre‐like” ceramics containing a small fraction of nickel mortar is developed. These materials are fabricated using nickel‐coated alumina platelets that are aligned using slip‐casting and rapidly sintered using spark‐plasma sintering. Dewetting of the nickel mortar during sintering is prevented by using NiO‐coated as well as Ni‐coated platelets. As a result, a “nacre‐like” alumina ceramic displaying a resistance‐curve toughness up to ≈16 MPa m ½ with a flexural strength of ≈300 MPa is produced.
High Altitude Flight Test of a 40-Foot Diameter (12.2 meter) Ringsail Parachute at Deployment Mach Number of 2.95
A 40-foot-nominal-diameter (12.2-meter) modified ringsail parachute was flight tested as part of the NASA Supersonic High Altitude Parachute Experiment (SHAPE) program. The 41-pound (18.6-kg) test parachute system was deployed from a 239.5-pound (108.6-kg) instrumented payload by means of a deployment mortar when the payload was at an altitude of 171,400 feet (52.3 km), a Mach number of 2.95, and a free-stream dynamic pressure of 9.2 lb/sq ft (440 N/m(exp 2)). The parachute deployed properly, suspension line stretch occurring 0.54 second after mortar firing with a resulting snatch-force loading of 932 pounds (4146 newtons). The maximum loading due to parachute opening was 5162 pounds (22 962 newtons) at 1.29 seconds after mortar firing. The first near full inflation of the canopy at 1.25 seconds after mortar firing was followed immediately by a partial collapse and subsequent oscillations of frontal area until the system had decelerated to a Mach number of about 1.5. The parachute then attained a shape that provided full drag area. During the supersonic part of the test, the average axial-force coefficient varied from a minimum of about 0.24 at a Mach number of 2.7 to a maximum of 0.54 at a Mach number of 1.1. During descent under subsonic conditions, the average effective drag coefficient was 0.62 and parachute-payload oscillation angles averaged about &loo with excursions to +/-20 degrees. The recovered parachute was found to have slight damage in the vent area caused by the attached deployment bag and mortar lid.
Na and Li ion diffusion in modified ASTM C 1260 test by Magnetic Resonance Imaging (MRI)
In the current study, MRI was applied to investigate lithium and sodium ion diffusion in cement paste and mortars containing inert sand and borosilicate glass. Paste and mortars were treated by complying with ASTM C 1260. Lithium and sodium distribution profiles were collected at different ages after different treatments. Results revealed that sodium ions had a greater diffusion rate than lithium ions, suggesting that Na reaches the aggregate particle surface before Li. Results also showed that Na and Li ions had a competitive diffusion process in mortars; soaking in a solution with higher [Li] favored Li diffusion but hindered Na diffusion. In mortars containing glass, a substantial amount of Li was consumed by the formation of ASR products. When [Li] in soaking solution was reduced to 0.37 N, a distinctive Na distribution profile was observed, indicating the free-state Na ions were continuously transformed to solid reaction products by ASR. Hence, in the modified ASTM C 1260 test, [Li] in the storage solution should be controlled at 0.74 N, in order to completely prevent the consumption of Na ions and thus stop ASR.
Chemo-mechanical modeling for prediction of alkali silica reaction (ASR) expansion
The effect of the size of the aggregate on ASR expansion has already been well illustrated. This paper presents a microscopic model to analyze the development of ASR expansion of mortars containing reactive aggregate of different sizes. The attack of the reactive silica by alkali was determined through the mass balance equation, which controls the diffusion mechanism in the aggregate and the fixation of the alkali in the ASR gels. The mechanical part of the model is based on the damage theory in order to assess the decrease of stiffness of the mortar due to cracking caused by ASR and to calculate the expansion of a Representative Elementary Volume (REV) of concrete. Parameters of the model were estimated by curve fitting the expansions of four experimental mortars. The paper shows that the decrease of expansion with the size of the aggregate and the increase of the expansion with the alkali content are reproduced by the model, which is able to predict the expansions of six other mortars containing two sizes of reactive aggregate and cast with two alkali contents.
Interface Problem Formulation Improvements with Application to Nuclear Fuel Performance Analysis
The U.S. Department of Energy’s Nuclear Energy Advanced Modeling and Simulation Program aims to develop predictive capabilities by applying computational methods to the analysis and design of advanced reactor and fuel cycle systems. This program has been providing engineering scale support for the development of BISON, a high-fidelity and high-resolution fuel performance tool. This report documents new developments and robustness improvements in mechanical and thermal (gap heat transfer) contact formulations. The improvements range from the migration of industrial level (“assessment”) nuclear fuel model setups to the usage of mortar formulations, the addition of frictional contact to one-dimensional layered representations of fuel and cladding components, and the addition of the Petrov-Galerkin approach to dual mortar, which improves performance on curved, relatively coarse meshes. In addition, the Lagrange-multiplier enforcement of mechanical mortar contact constraints has been extended to two additional types of enforcement: penalty and augmented Lagrange-Uzawa. We show that the latter approach yields the same interface results as dual mortar in the Multiphysics Object-Oriented Simulation Environment, with the advantage of not worsening the condition number of the system matrix—thereby enabling the use of some general implementations of iterative preconditioners, at the expense of additional system evaluations (i.e., augmentations).
Effect of pulverized fuel ash and CO{sub 2} curing on the water resistance of magnesium oxychloride cement (MOC)
This paper presents a study on the use of pulverized fuel ash (PFA) to improve the water resistance of magnesium oxychloride cement (MOC). Strength retention coefficients and volume stability were tested to evaluate the water resistance of MOC, in which the addition of PFA resulted in a remarkable improvement. The characterization of hydration products before and after water immersion was carried out using quantitative X-ray diffraction (QXRD), thermogravimetric (TG), Fourier-transformed infrared spectroscopy (FTIR) and scanning electron microscope (SEM). With the Q-XRD analysis, it was shown that the addition of PFA could result in the great increase of the amount of amorphous phase during air curing. This amorphous gel was identified as a mixture of magnesium-chloride-silicate-hydrate gel (M-Cl-S-H gel) and magnesium-chloride-hydrate gel (M-Cl-H gel) by elemental mapping scanning. It suggested that PFA could not only react with MOC to form M-Cl-S-H gel, but also change the morphology of magnesium oxychloride. The generation of insoluble M-Cl-S-H gel and M-Cl-H gel and densification of the microstructure contributed to the improvement of the water resistance of MOC. The MOC mortar expanded during air curing due to the hydration of excess MgO. Water immersion led to more expansion of MOC mortar as a result of the continuously hydration of excess MgO and the formation of Mg(OH){sub 2}. Adding PFA could increase the expansion of MOC mortar during air curing, which may because the amorphous gel could remain more water and benefit to the hydration of MgO. While, the addition of PFA could decrease the expansion of cement mortar during water immersion perhaps due to the reduction of the content of excess MgO and the insoluble amorphous-gel-layer that protect the MgO from hydration. Moreover, CO{sub 2} curing could further improve the performance of the PFA-blended MOC due to the formation of a higher content of amorphous gel.