SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
To predetermine the mechanical properties of rigid plastics as a function of plasticizer content and composition, a set of equations has been empirically derived. These relate strain rate, yield stress, temperature, and weight fraction of the plasticizer.
Mechanical properties of Group 4B and Group 5B transition metal monocarbides
Mechanical properties of alloys molybdenum hafnium carbon compounds
Multiple transitions and relaxations of polymers in relation to mechanical properties
Mechanical properties and stress corrosion evaluation of MP 35N multiphase alloy at cryogenic temperature
Thermal and air environment effects on mechanical properties of graphite/polyimide laminates
Thermal and mechanical properties data were obtained for a low density elastomeric resin based ablation material with phenolic-glass honeycomb reinforcement. Data were obtained for the material in the charred and uncharred state. Ablation material specimens were charred in a laboratory furnace at temperatures in the range from 600 K to 1700 K to obtain char specimens representative of the ablation char layer formed during reentry. These specimens were then used to obtain effective thermal conductivity, heat capacity, porosity, and permeability data at the char formation temperature. This provided a boxing of the data which enables the prediction of the transient response of the material during ablation. Limited comparisons were made between the furnace charred specimens and specimens which had been exposed to simulated reentry conditions.
Two reports describe tests to determine mechanical properties of laminates made of reaction-bonded silicon nitride matrices reinforced with 30 volume percent of aligned silicon carbide fibers. Emphasizes different aspects of topic. One focuses on behavior related to strength at ambient temperature; other focuses on strength after exposure to high temperatures. Overall, results indicate that composites are candidates for use at high temperatures; for example, as components of heat engines.
Mechanical properties from an advanced, nickel-base superalloy disk, with a dual grain structure consisting of a fine grain bore and coarse grain rim, were evaluated. The dual grain structure was produced using NASA's low cost Dual Microstructure Heat Treatment (DMHT) process. The results showed the DMHT disk to have a high strength, fatigue resistant bore comparable to a subsolvus (fine grain) heat treated disk, and a creep resistant rim comparable to a supersolvus (coarse grain) heat treated disk. Additional work on subsolvus solutioning before or after the DMHT conversion appears to be a viable avenue for further improvement in disk properties.
The mechanical properties of several cast blade superalloys and one powder metallurgy disk superalloy were assessed for potential use in a dual alloy hybrid disk concept of joined dissimilar bore and web materials. Grain size was varied for each superalloy class. Tensile, creep, fatigue, and notch fatigue tests were performed at 704 to 815 degC. Typical microstructures and failure modes were determined. Preferred materials were then selected for future study as the bore and rim alloys in this hybrid disk concept. Powder metallurgy superalloy LSHR at 15 micron grain size and single crystal superalloy LDS-1101+Hf were selected for further study, and future work is recommended to develop the hybrid disk concept.
In Fused Filament Fabrication (FFF) 3D printing a part is made by extruding material layer by layer. Benefits of FFF are the ability to print complex shapes quickly and at a lower cost compared to other manufacturing methods. In this work, filaments composed of either silicon carbide (SiC) or zirconium silicate ceramic particulates in a polylactic-acid (PLA) matrix were used to print specimens for microstructural analysis and mechanical testing. Pure PLA samples were also printed and tested as a baseline for comparison. A Design of Experiments approach was used to test the interactions between three different parameters and their effect on ultimate strength, Young’s modulus, and yield strength. For compression test specimens, these parameters were infill percentage, number of shells, and print orientation angle. For tensile test specimens, the parameters were layer height, number of shells, and infill orientation angle. Pre- and post-compression test samples were evaluated by scanning electron microscopy for microstructural analysis. Infill percentage had the greatest effect on mechanical properties while number of shells and print orientation angle had minor effects. When changing the layer lines from perpendicular to parallel, relative to the loading direction, SiC-PLA had higher mechanical properties while pure PLA properties had decreased, and zirconium silicate-PLA had mix results.
Mechanical properties determined for cross linked polymethyl methacrylate under stress-relaxation test method
Plane strain fracture toughness and mechanical properties of titanium alloy at room and cryogenic temperatures
Influence of boron additions on physical and mechanical properties of arc-melted tungsten and of tungsten-tantalum alloy
Mechanical properties of Ti-Fe-Cr titanium alloys with varying amounts of iron
As NASA missions extend beyond low Earth orbit, increasing reliance is placed on carbon fiber reinforced polymer (CFRP) composites for spacecraft structures where mass efficiency, durability, and long-term reliability are critical. In service, these materials are subjected to a combination of ultraviolet radiation, vacuum, ionizing radiation, atomic oxygen, and extreme thermal excursions under sustained mechanical loading. Flight systems such as the Boeing Starliner and SpaceX Dragon employ external composite structures that will experience these environments for extended durations. Although prior spaceflight and ground studies have reported limited changes in bulk mechanical properties, the synergistic effects of these environments on composite microstructure, particularly at the fiber matrix interphase, remain insufficiently characterized and represent a potential qualification and reliability risk. This study investigates the effects of short-term cryogenic exposure on a radiation shielding carbon epoxy composite, SC2020, as a ground-based analog for space relevant thermal extremes. The SC2020 material system has previously flown on the International Space Station under the Materials International Space Station Experiment (MISSE) program. Composite specimens were exposed to liquid nitrogen for 6 and 24 hours and evaluated using a multiscale characterization framework that combined ASTM D3039 tensile testing, Atomic Force Microscopy (AFM) based interphase analysis, and helium gas permeability measurements. Tensile testing showed no statistically significant or permanent degradation in global strength or modulus following cryogenic exposure. In contrast, AFM measurements revealed reductions in interphase modulus, weakened adhesion, and increased nanoscale heterogeneity, indicating localized degradation mechanisms not captured by conventional bulk testing. Gas permeability measurements showed a progressive increase in helium diffusion with exposure duration, consistent with micro-void formation or partial interfacial debonding. The results indicate that cryogenic exposure initiates degradation at the fiber matrix interphase while leaving global mechanical properties largely unchanged over short durations. These findings underscore the importance of multiscale diagnostics for identifying early-stage damage mechanisms that may influence long term performance and qualification margins for spaceflight composite structures. The data presented establish a cryogenic baseline for comparison with forthcoming MISSE flight exposure results and support ongoing NASA Established Program to Stimulate Competitive Research (EPSCoR) efforts aimed at improving composite qualification methodologies, risk assessment, and reliability prediction for space environments.
Mechanical properties of fiberglass anisotropic laminated plastics - tensile, compression, impact and shear tests
Grain Boundary Engineering can enhance the population of structurally-ordered "low S" Coincidence Site Lattice (CSL) grain boundaries in the microstructure. In some alloys, these "special" grain boundaries have been reported to improve overall resistance to corrosion, oxidation, and creep resistance. Such improvements could be quite beneficial for superalloys, especially in conditions which encourage damage and cracking at grain boundaries. Therefore, the effects of GBE processing on high-temperature mechanical properties of the cast and wrought superalloy Allvac 718Plus (Allvac ATI) were screened. Bar sections were subjected to varied GBE processing, and then consistently heat treated, machined, and tested at 650 C. Creep, tensile stress relaxation, and dwell fatigue crack growth tests were performed. The influences of GBE processing on microstructure, mechanical properties, and associated failure modes are discussed.