SEARCH · Engineering Papers
Results for “Li plasticity”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Remediation and upcycling of microplastics by algae with wastewater nutrient removal and bioproduction potential
Microplastics have emerged as major environmental hazards that require efficient, cost-effective, and sustainable remediation technologies. This study introduces an integrative platform for the remediation and upcycling of microplastics by algae, while synergizing with plastic upcycling, wastewater treatment, and algal production. The strategy employs a mechanism that enhances hydrophobic interactions between the cell surface and microplastics, enabling rapid aggregation and removal. The platform achieves a superior microplastic removal efficiency of 91.4% within 1 hour, with a capacity of 0.1-gram microplastic per gram of biomass. Furthermore, the study demonstrates an upcycling strategy that converts microplastics-enriched cyanobacteria into plastic composites with unique performance. This work also integrates microplastic removal with cyanobacterial bioproduction and wastewater treatment, offering an approach that synergizes remediation with these value-added processes. Ultimately, this platform provides a viable and sustainable pathway to address microplastic pollution by creating value through plastic upcycling, wastewater nutrient removal, and CO 2 -based bioproduction.
Environmental fatigue of an Al-Li-Cu alloy. Part 3: Modeling of crack tip hydrogen damage
Environmental fatigue crack propagation rates and microscopic damage modes in Al-Li-Cu alloy 2090 (Parts 1 and 2) are described by a crack tip process zone model based on hydrogen embrittlement. Da/dN sub ENV equates to discontinuous crack advance over a distance, delta a, determined by dislocation transport of dissolved hydrogen at plastic strains above a critical value; and to the number of load cycles, delta N, required to hydrogenate process zone trap sites that fracture according to a local hydrogen concentration-tensile stress criterion. Transgranular (100) cracking occurs for process zones smaller than the subgrain size, and due to lattice decohesion or hydride formation. Intersubgranular cracking dominates when the process zone encompasses one or more subgrains so that dislocation transport provides hydrogen to strong boundary trapping sites. Multi-sloped log da/dN-log delta K behavior is produced by process zone plastic strain-hydrogen-microstructure interactions, and is determined by the DK dependent rates and proportions of each parallel cracking mode. Absolute values of the exponents and the preexponential coefficients are not predictable; however, fractographic measurements theta sub i coupled with fatigue crack propagation data for alloy 2090 established that the process zone model correctly describes fatigue crack propagation kinetics. Crack surface films hinder hydrogen uptake and reduce da/dN and alter the proportions of each fatigue crack propagation mode.
Upcycling Carbon Dioxide: Ethylene Glycol from Cleaned Fossil Carbon Power Production CO2 and Renewable Electricity - Phase I
Explore the source record for details and available documents.
High-pressure strengthening in ultrafine-grained metals
The Hall–Petch relationship, according to which the strength of a metal increases as the grain size decreases, has been reported to break down at a critical grain size of around 10 to 15 nanometres. As the grain size decreases beyond this point, the dominant mechanism of deformation switches from a dislocation-mediated process to grain boundary sliding, leading to material softening. In one previous approach, stabilization of grain boundaries through relaxation and molybdenum segregation was used to prevent this softening effect in nickel–molybdenum alloys with grain sizes below 10 nanometres. Here we track in situ the yield stress and deformation texturing of pure nickel samples of various average grain sizes using a diamond anvil cell coupled with radial X-ray diffraction. Our high-pressure experiments reveal continuous strengthening in samples with grain sizes from 200 nanometres down to 3 nanometres, with the strengthening enhanced (rather than reduced) at grain sizes smaller than 20 nanometres. Here, we achieve a yield strength of approximately 4.2 gigapascals in our 3-nanometre-grain-size samples, ten times stronger than that of a commercial nickel material. A maximum flow stress of 10.2 gigapascals is obtained in nickel of grain size 3 nanometres for the pressure range studied here. We see similar patterns of compression strengthening in gold and palladium samples down to the smallest grain sizes. Simulations and transmission electron microscopy reveal that the high strength observed in nickel of grain size 3 nanometres is caused by the superposition of strengthening mechanisms: both partial and full dislocation hardening plus suppression of grain boundary plasticity. These insights contribute the ongoing search for ultrastrong metals via materials engineering.
Bioconversion of Homogeneous Linear C-Lignin to Polyhydroxyalkanoates
Here, the bioconversion of homogeneous linear catechyl lignin (C-lignin) to polyhydroxyalkanoates (PHA) was examined for the first time in this study. C-lignins from vanilla, euphorbia, and candlenut seed coats (denoted as C1, C2, and C3, respectively) varied in their molecular structures, which showed different molecular weight distributions, etherification degrees, and contents of hydroxyl groups. A notable amount of nonetherified catechol units existed within C1 and C2 lignins, and these catechol units were consumed during fermentation. These results suggested that the nonetherified catechol structure was readily converted by Pseudomonas putida KT2440. Since the weight-average molecular weight of C2 raw lignin was 26.7% lower than that of C1, the bioconversion performance of C2 lignin was more outstanding. The P. putida KT2440 cell amount reached the maximum of 9.3 × 10 7 CFU/mL in the C2 medium, which was 37.9 and 82.4% higher than that in the C1 and C3 medium, respectively. Accordingly, PHA concentration reached 137 mg/L within the C2 medium, which was 41.2 and 149.1% higher than the C1 and C3 medium, respectively. Overall, C-lignin, with a nonetherified catechol structure and low molecular weight, benefits its microbial conversion significantly.
Stress Concentration and Fracture at Inter-variant Boundaries in an Al-Li Alloy
Delamination fracture has limited the use of lightweight Al-Li alloys. Studies of secondary, delamination cracks in alloy 2090, L-T fracture toughness samples showed grain boundary failure between variants of the brass texture component. Although the adjacent texture variants, designated B(sub s1) and B(sub s2), behave similarly during rolling, their plastic responses to mechanical tests can be quite different. EBSD data from through-thickness scans were used to generate Taylor factor maps. When a combined boundary normal and shear tensor was used in the calculation, the delaminating grains showed the greatest Taylor Factor differences of any grain pairs. Kernel Average Misorientation (KAM) maps also showed damage accumulation on one side of the interface. Both of these are consistent with poor slip accommodation from a crystallographically softer grain to a harder one. Transmission electron microscopy was used to confirm the EBSD observations and to show the role of slip bands in the development of large, interfacial stress concentrations. A viewgraph presentation accompanies the provided abstract.
Unlocking Electrostrain in Plastically Deformed Barium Titanate
Achieving substantial electrostrain alongside a large effective piezoelectric strain coefficient (d 33 *) in piezoelectric materials remains a formidable challenge for advanced actuator applications. Here, in this work, a straightforward approach to enhance these properties by strategically designing the domain structure and controlling the domain switching through the introduction of arrays of ordered {100}<100> dislocations is proposed. This dislocation engineering yields an intrinsic lock-in steady–state electrostrain of 0.69% at a low field of 10 kV cm -1 without external stress and an output strain energy density of 5.24 J cm -3 in single-crystal BaTiO 3 , outperforming the benchmark piezoceramics and relaxor ferroelectric single-crystals. Additionally, applying a compression stress of 6 MPa fully unlocks electrostrains exceeding 1%, yielding a remarkable d 33 * value over 10 000 pm V -1 and achieving a record-high strain energy density of 11.67 J cm -3 . Optical and transmission electron microscopy, paired with laboratory and synchrotron X-ray diffraction, is employed to rationalize the observed electrostrain. Phase-field simulations further elucidate the impact of charged dislocations on domain nucleation and domain switching. These findings present an effective and sustainable strategy for developing high-performance, lead-free piezoelectric materials without the need for additional chemical elements, offering immense potential for actuator technologies.
Catalytic Conversion of Model Compounds of Plastic Pyrolysis Oil over ZSM-5
Mechanistic investigation of the catalytic conversion of model compounds for plastic pyrolysis oil (1-octene, octadiene, octane, and toluene) over ZSM-5 in a fixed-bed reactor was studied. 1-Octene breaks down into smaller olefins, which undergo further cracking, oligomerization, cyclization, and hydrogen transfer to eventually produce benzene, toluene, xylene (BTX), coke, and hydrogen. The effect of contact time on 1-octene conversion was further investigated and compared with thermodynamics analyses to elucidate the reaction network. Under the reaction conditions (500 oC, 1 atm), octadiene undergoes thermal coking, significantly contributing to reactor fouling. The products from octane cracking are similar to the products from 1-octene conversion whereas toluene undergoes disproportionation, dealkylation and coking. The analysis of spent catalyst showed long-chain hydrocarbons created by oligomerization reactions filled the pores and covered the surface of the catalyst. As a result, when mesoporous ZSM-5 is used instead of conventional, product selectivity is maintained for 70 hours in time-on-stream experiments.
Uniaxial stress increases layer stacking disorder in calcium silicate hydrates with low calcium content
The long-term stress response of concrete is controlled by the intergrain and intragrain interactions of calcium-silicate-hydrates (C-S-H), nanocrystalline forms of tobermorites. To investigate both types of interactions, we examined the deviatoric stress response of 11 Å tobermorite powder with X-ray diffraction, finding that its layer stacking (i.e., sliding) disorder significantly increases. A similar experiment was performed on nanocrystalline C-S-H powders before and after applying a 360 MPa uniaxial stress. Layer stacking disorder (in the form of intragrain deformation) increases when there is low water content and when the basal spacing is large. We also find that grains with a smaller thickness-to-diameter aspect ratio are first to develop preferred orientation (in the form of intergrain sliding), facilitated by gel water. Furthermore, these findings show that intragrain deformations in C-S-H can occur at relatively low stresses and provide insights into the creep mechanism of C-S-H.
High temperature nanoindentation of Cu–TiN nanolaminates
Here, we examined the high temperature indentation response of physical vapor deposited Cu–TiN multilayered nanocomposites with layer thicknesses ranging from 5 nm to 200 nm. A decrease in hardness with increasing temperature was observed, along with a strong correlation between the hardness and the nanometer-level TiN grain sizes, rather than layer thickness. The apparent activation energies calculated from the high temperature indentation experiments indicated that, for all but the smallest layer thicknesses, the deformation of copper in the nanolaminates dominate the plastic response in these composites. In the finest layer thicknesses, a decrease in the apparent activation energy value indicated possible co-deformation of Cu and TiN.
Composition-dependent fracture energy in metallic glasses
The interplay between metallic glasses (MGs) mechanical properties, fracture energy (G), and glass-forming ability (GFA) and their dependence on alloy composition remain poorly understood. Here, we perform molecular dynamics simulations to investigate the intrinsic composition-dependence of G in Cu x Zr 100-x MGs (x = 20, 30, 40, 50, 64). The results indicate that the value of G increases with Cu content. In addition, it is revealed that MGs with higher G values display higher Poisson’s ratio (ν) and GFA, suggesting a close correlation between fracture toughness, mechanical properties, and GFA. This correlation between G, ν and GFA can be understood based on the fragility (m) of supercooled liquids, which is directly related to the structural heterogeneity in MGs. Larger m values are related to dynamic slowdown and supercooled liquid stabilization, which enhance GFA and the formation of pronounced structural heterogeneity, comprised of loosely packed regions that favor β-relaxation and the activation of shear transformation zones. Those concurrently promote the expansion of the plastic zone at the crack tip, enhancing the observed value of G. Furthermore, these simulation results shed light on the intrinsic relationship between fracture toughness, mechanical properties, and alloy composition in MGs.
Hybrid biological-chemical strategy for converting polyethylene into a recyclable plastic monomer using engineered Corynebacterium glutamicum
Converting polyethylene (PE) into valuable materials, particularly ones that are better for the environment than the incumbent plastics, not only helps mitigate environmental issues caused by plastic waste but also alleviates the long-standing problem of microbial fermentation competing with food supplies. However, the inherent robustness of PE due to its strong carbon-carbon bonds and high molecular weight necessitates harsh decomposition conditions, resulting in diverse decomposition outcomes that present significant challenges for downstream applications, especially for bioconversion. In this study, we demonstrate a hybrid biological-chemical conversion process for PE, converting its decomposition products, namely short-chain diacids, into a monomer, β-keto-δ-lactone (BKDL), for highly recyclable polydiketoenimine plastics using engineered Corynebacterium glutamicum. Since BKDL synthesis requires a substantial supply of malonyl-CoA, we employed an alternative biosynthesis pathway that leverages C. glutamicum's natural proficiency in amino acid production. We optimized this pathway in vivo by minimizing carbon loss to CO2 and byproducts, improving the transporter system, and maximizing co-factor regeneration. Furthermore, we co-optimized the PE deconstruction process to produce predominantly C4 to C6 diacids and integrated three catabolic pathways into the engineered strain to enhance diacid utilization, maximizing the carbon conversion from PE. Finally, an engineered polyketide synthase was introduced into C. glutamicum to enable BKDL synthesis. This work demonstrates the potential of a chemo-biological hybrid strategy for recycling plastic waste, highlighting its promise in addressing environmental challenges and promoting sustainable materials.
Electrolyte design for LiF-rich solid–electrolyte interfaces to enable high-performance microsized alloy anodes for batteries
Lithium batteries with Si, Al or Bi microsized (>10 µm) particle anodes promise a high capacity, ease of production, low cost and low environmental impact, yet they suffer from fast degradation and a low Coulombic efficiency. In this paper, we demonstrate that a rationally designed electrolyte (2.0 M LiPF 6 in 1:1 v/v mixture of tetrahydrofuran and 2-methyltetrahydrofuran) enables 100 cycles of full cells that contain microsized Si, Al and Bi anodes with commercial LiFePO 4 and LiNi 0.8 Co 0.15 Al 0.05 O 2 cathodes. Alloy anodes with areal capacities of more than 2.5 mAh cm -2 achieved >300 cycles with a high initial Coulombic efficiency of >90% and average Coulombic efficiency of >99.9%. These improvements are facilitated by the formation of a high-modulus LiF–organic bilayer interphase, in which LiF possesses a high interfacial energy with the alloy anode to accommodate plastic deformation of the lithiated alloy during cycling. Lastly, this work provides a simple yet practical solution to current battery technology without any binder modification or special fabrication methods.
Single-Atom Nickel Dispersed on Mo 2 TiC 2 T x MXene for Upcycling of Polyolefins via Catalytic Hydropyrolysis for Fuels and Lubricants
Plastic waste has been a major social and environmental problem. Chemical upcycling of plastic waste into transportation fuels or lubricant oil has emerged as an attractive and promising approach to convert plastic waste into valuable products. However, conventional catalyst systems often require high-pressure hydrogen, prolonged residence time, and the use of noble metal catalysts. Here, we present zero-valent nickel single atoms on Mo-based MXenes (Ni/Mo 2 TiC 2 T x ) for effective hydrogenation of polyolefins. In situ spectroscopic and microscopic characterizations demonstrate the formation of Ni–Mo and Ni–C bonds at a low Ni loading, resulting in the formation of dispersed intercalated Ni atoms. The catalysts were then employed to convert polyethylene into fuels and lubricant molecules under atmospheric hydrogen pressure, short vapor residence time (τ < 1 s), and mild reaction temperature (300 °C). We further demonstrated the possibility of tuning the Ni structure by changing the Ni loading, attributed to the strong metal–support interactions (MSIs) with the Mo 2 TiC 2 T x support. Under optimized conditions, 22.5 C% gasoline, 12.0 C% diesel, 19.2 C% jet fuel (JP-8), and 37.4 C% lubricant were produced over 0.5% Ni/Mo 2 TiC 2 T x . This work highlights the potential of utilizing MSIs of Mo 2 TiC 2 T x MXenes to synthesize single-atom catalysts (SACs) for upcycling plastic waste into higher-value products.
In-situ observation of deformation twin associated sub-grain boundary formation in copper single crystal under bending
Not Available
A concurrent irradiation-mechanics multiscale coupling model
The vast majority of our current knowledge regarding the basic mechanisms controlling irradiation effect on mechanical properties is based almost entirely on the results of post-irradiation experiments or theoretical models. However, the concurrent effects of irradiation, mechanical stress, and thermal damage on the failure phenomena of materials and components remain largely unexplored due to its internal multiscale-multiphysics coupling nature. Here, we present here a concurrent irradiation-mechanics multiscale coupling model. The concurrent evolutions of nanoscale irradiation defect clusters, microscale dislocation configurations, and mechanical responses are well captured based on coupling cluster dynamics, discrete dislocation dynamics, and the finite element methods using an effective time marching scheme. Model predictions of defect densities and size are in general agreement with experimental observations. Irradiation hardening is shown to take place also in samples undergoing concurrent irradiation-mechanical loading, similar to samples tested post-irradiation. However, the occurrence of plastic flow localization and dislocation channel formation is not accompanied with apparent yield drop (softening) under concurrent irradiation-mechanical loading conditions, which is different from the post-irradiation case.
Root system architecture and environmental flux analysis in mature crops using 3D root mesocosms
Current methods of root sampling typically only obtain small or incomplete sections of root systems and do not capture their true complexity. To facilitate the visualization and analysis of full-sized plant root systems in 3-dimensions, we developed customized mesocosm growth containers. While highly scalable, the design presented here uses an internal volume of 45 ft 3 (1.27 m 3 ), suitable for large crop and bioenergy grass root systems to grow largely unconstrained. Furthermore, they allow for the excavation and preservation of 3-dimensional root system architecture (RSA), and facilitate the collection of time-resolved subterranean environmental data. Sensor arrays monitoring matric potential, temperature and CO 2 levels are buried in a grid formation at various depths to assess environmental fluxes at regular intervals. Methods of 3D data visualization of fluxes were developed to allow for comparison with root system architectural traits. Following harvest, the recovered root system can be digitally reconstructed in 3D through photogrammetry, which is an inexpensive method requiring only an appropriate studio space and a digital camera. We developed a pipeline to extract features from the 3D point clouds, or from derived skeletons that include point cloud voxel number as a proxy for biomass, total root system length, volume, depth, convex hull volume and solidity as a function of depth. Ground-truthing these features with biomass measurements from manually dissected root systems showed a high correlation. We evaluated switchgrass, maize, and sorghum root systems to highlight the capability for species wide comparisons. We focused on two switchgrass ecotypes, upland (VS16) and lowland (WBC3), in identical environments to demonstrate widely different root system architectures that may be indicative of core differences in their rhizoeconomic foraging strategies. Finally, we imposed a strong physiological water stress and manipulated the growth medium to demonstrate whole root system plasticity in response to environmental stimuli. Hence, these new “3D Root Mesocosms” and accompanying computational analysis provides a new paradigm for study of mature crop systems and the environmental fluxes that shape them.