Results for “Landing Gear” — Page 9

A theoretical study was made of the shimmy of castering wheels. The theory is based on the discovery of a phenomenon called kinematic shimmy. Experimental checks, use being made of a model having low-pressure tires, are reported and the applicability of the results to full scale is discussed. Theoretical methods of estimating the spindle viscous damping and the spindle solid friction necessary to avoid shimmy are given. A new method of avoiding shimmy -- lateral freedom -- is introduced.

Kantrowitz, Arthur↗

NASA NTRS1930

Impact tests on rubber compression springs for airplane landing gears

The present report gives the results of tests which were made for the purpose of solving the problem of whether diagrams obtained from pressure tests could be conclusive for the determination of the safe impact coefficients. It is first established that the rubber rings adhere firmly to the compression surfaces during deformation. Suggestions are thus obtained for a constructive simplification of the rubber rings. The hysteresis phenomenon is ascribed to external and internal friction forces. A device for falling tests is then described with which the process of shock absorption with rubber rings was tested.

Hohenemser, K↗

NASA NTRS2006

Investigations of Shuttle Main Landing Gear Door Environmental Seals

The Columbia Accident investigation Board (CAIB) requested an investigation into the MLG door seals. Initially, the MLG door seals were thought to have been a potential contributor to the loss of Columbia. These suspicions were later found to be untrue, but the seals remained as a cause for concern in future flights. MLG door seals comprised of thermal barrier and environmental seal. This study focuses on the environmental seal for the MLG door.

Finkbeiner, Joshua↗

NASA NTRS2015

An Overview of Contributions for Nose Landing Gear Configuration - BANC-III Workshop

No abstract available

Khorrami, Mehdi R.↗

NASA NTRS2019

LAVA Lattice Boltzmann Development/Application to Landing Gear

No abstract available

Boltzmann↗

NASA NTRSDate not supplied

Design of a Manufacturing Demonstration Unit for a Composite Lunar Landing Gear Strut

The goal of the current work was to develop an analytical framework for design of composite struts using various levels of model fidelity. Rapid optimization trade studies were performed using low fidelity two-dimensional (2D) axisymmetric models with smeared composite properties. The optimum 2D model was compared with three-dimensional (3D) models with higher levels of fidelity in material property representation. Good agreement was found with all models. The buckling performance of the highest fidelity 3D model was found to be satisfactory for the intended loading conditions. An additional goal of this work was to perform an initial assessment of using automated fiber placement (AFP) and other advanced manufacturing methods to explore their feasibility for the fabrication of struts for lunar landers, strut-braced wings, and other aerospace components. The designs produced during this study are intended to be used to develop manufacturing demonstration units (MDU) that can be fabricated at the Integrated Structural Assembly of Advanced Composites (ISAAC) facility at Langley Research Center (LaRC) and tested in lab facilities at LaRC.

carbon-epoxy↗

NASA NTRSDate not supplied

Design of a Manufacturing Demonstration Unit for a Composite Lunar Landing Gear Strut

The goal of the current work was to develop an analytical framework for design of composite struts using various levels of model fidelity. Rapid optimization trade studies were performed using low fidelity two-dimensional (2D) axisymmetric models with smeared composite properties. The optimum 2D model was compared with three-dimensional (3D) models with higher levels of fidelity in material property representation. Good agreement was found with all models. The buckling performance of the highest fidelity 3D model was found to be satisfactory for the intended loading conditions. An additional goal of this work was to perform an initial assessment of using automated fiber placement (AFP) and other advanced manufacturing methods to explore their feasibility for the fabrication of struts for lunar landers, strut-braced wings, and other aerospace components. The designs produced during this study are intended to be used to develop manufacturing demonstration units (MDU) that can be fabricated at the Integrated Structural Assembly of Advanced Composites (ISAAC) facility at Langley Research Center (LaRC) and tested in lab facilities at LaRC.

carbon-epoxy↗