Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Irradiance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

AGC-4 Specimen Post-Irradiation Examination Data Interim Report

This interim report documents preliminary results of the post-irradiation examination material property testing from the fourth advanced graphite creep (AGC), AGC 4, capsule specimens. This is the fourth of a series of six irradiation test trains planned as part of the AGC experiment to fully characterize the neutron irradiation effects and radiation creep behavior of current nuclear graphite grades to moderate dose levels (=7 dpa). The AGC 4 capsule was irradiated in the Idaho National Laboratory Advanced Test Reactor at a nominal temperature of 800°C and to a peak dose of 8 dpa. Half of the AGC-4 specimens were subjected to compressive stresses to induce irradiation creep. Post-irradiation testing and measurement results are reported with the exception of thermal testing, which is still in progress, and irradiation mechanical strength testing. Additionally, some specimens initially deemed too hot to be examined in the ART Graphite laboratory may still be measured. The data reported includes specimen dimensions for both stressed and unstressed specimens to establish the irradiation creep rates, mass and dimensional data necessary to derive density, elastic constants (Young?s modulus, shear modulus, and Poisson?s ratio) from ultrasonic time of flight velocity measurements, Young?s modulus from the fundamental frequency of vibration, and electrical resistivity. A more complete evaluation of trends in the material property changes, as well as irradiation-induced creep due to the irradiation environment and applied load on the specimens, will be discussed later in AGC 4 post-irradiation examination analysis reports.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

AGC-4 Specimen Post-Irradiation Examination Data Interim Report

This interim report documents preliminary results of the post-irradiation examination material property testing from the fourth advanced graphite creep (AGC), AGC 4, capsule specimens. This is the fourth of a series of six irradiation test trains planned as part of the AGC experiment to fully characterize the neutron irradiation effects and radiation creep behavior of current nuclear graphite grades to moderate dose levels (=7 dpa). The AGC 4 capsule was irradiated in the Idaho National Laboratory Advanced Test Reactor at a nominal temperature of 800°C and to a peak dose of 8 dpa. Half of the AGC-4 specimens were subjected to compressive stresses to induce irradiation creep. Post-irradiation testing and measurement results are reported with the exception of thermal testing, which is still in progress, and irradiation mechanical strength testing. Additionally, some specimens initially deemed too hot to be examined in the ART Graphite laboratory may still be measured. The data reported includes specimen dimensions for both stressed and unstressed specimens to establish the irradiation creep rates, mass and dimensional data necessary to derive density, elastic constants (Young?s modulus, shear modulus, and Poisson?s ratio) from ultrasonic time of flight velocity measurements, Young?s modulus from the fundamental frequency of vibration, and electrical resistivity. A more complete evaluation of trends in the material property changes, as well as irradiation-induced creep due to the irradiation environment and applied load on the specimens, will be discussed later in AGC 4 post-irradiation examination analysis reports.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Indirectly probing the structural change in ion-irradiated Zr-Based metallic glasses from small scale mechanical tests

Ion irradiation was applied to tailor the structural heterogeneities in Zr-based metallic glasses at room temperature. Experimental methods of X-ray diffraction, nanoindentation, and micropillar compression were conducted to examine the irradiation effects on their structural and mechanical property changes. It is found that the irradiated materials retained amorphous structure after room-temperature Ni ion irradiation. The reduction of elastic modulus and hardness measured by nanoindentation indicated the irradiation-induced mechanical degradation. A unified statistic model was employed to quantitatively predict the density and strength of irradiation defects, although their specific structural and physical nature is not explicitly included in this model. The transition of non-intersecting shear bands to multiple intersecting shear bands was observed on compression tests of irradiated micropillars with the increase of irradiation dose. Furthermore, the analysis of the displacement excursion of micropillar compression tests indicated a different deformation mode from the unirradiated state. These results from nanoindentation pop-in and micro-pillar compression tests suggested that irradiation eventually leads to a new state with different types and characteristics of structural heterogeneities from violent displacement cascades and non-equilibrium energy deposition/dissipation processes, which also proves ion irradiation as an effective method to tune the structure and mechanical properties of metallic glasses.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A concurrent irradiation-mechanics multiscale coupling model

The vast majority of our current knowledge regarding the basic mechanisms controlling irradiation effect on mechanical properties is based almost entirely on the results of post-irradiation experiments or theoretical models. However, the concurrent effects of irradiation, mechanical stress, and thermal damage on the failure phenomena of materials and components remain largely unexplored due to its internal multiscale-multiphysics coupling nature. Here, we present here a concurrent irradiation-mechanics multiscale coupling model. The concurrent evolutions of nanoscale irradiation defect clusters, microscale dislocation configurations, and mechanical responses are well captured based on coupling cluster dynamics, discrete dislocation dynamics, and the finite element methods using an effective time marching scheme. Model predictions of defect densities and size are in general agreement with experimental observations. Irradiation hardening is shown to take place also in samples undergoing concurrent irradiation-mechanical loading, similar to samples tested post-irradiation. However, the occurrence of plastic flow localization and dislocation channel formation is not accompanied with apparent yield drop (softening) under concurrent irradiation-mechanical loading conditions, which is different from the post-irradiation case.

42 ENGINEERING↗
DOE OSTI2021

Impact of neutron irradiation on the thermophysical properties of additively manufactured stainless steel and inconel

The deployment of additive manufacturing (AM) technologies to support the nuclear energy industry is limited by the current lack of data related to the irradiation performance of AM parts. The Colorado School of Mines is conducting a multi-year irradiation and post irradiation examination project to study the impacts of neutron irradiation on stainless steel 316L and Inconel 718 and 625 specimens produced by several commercially available AM techniques and irradiated in the Advanced Test Reactor (ATR) at the Idaho National Laboratory (INL). This paper presents initial results on the impact of neutron irradiation on the heat capacity, the thermal diffusivity, and the thermal conductivity of the specimens at temperatures between 100 oC and 400 oC. The unirradiated AM specimens have heat capacity values similar to, or lower than, the reference values, regardless of manufacturing method or material. The irradiated AM specimens have average heat capacities greater than the unirradiated specimens and reference values in every case. Additionally, the thermal diffusivities of the unirradiated AM specimens are either larger or statistically similar to the reference values. The irradiated AM specimens exhibit lower thermal diffusivities compared to the reference thermal diffusivity values. One of the stainless steel 316L laser powder bed fusion samples exhibited thermal diffusivity values with statistically significant anisotropy prior to and after irradiation. The thermal conductivities of the unirradiated AM stainless steel 316L specimens and the unirradiated Inconel 718 specimens are lower or statistically similar to the reference values. The unirradiated Inconel 625 specimens exhibit slightly higher thermal conductivity values than the reference values. The irradiated specimens show a significant increase in thermal conductivity compared to the unirradiated specimens and the reference values for all materials.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

The effect of neutron irradiation on conventional and nanocrystalline nickel: NSUF Work Package UA-22PN080501 Milestone M3UA-22PN0805012 (Final Report)

Even though nanocrystalline materials (20-100 nm) present an unprecedented potential, scientific knowledge related to the effect of neutron irradiation on the mechanical properties and microstructure is still scarce. Most of the past studies were conducted using ion irradiation which may not have the same effect as neutron irradiation because of the smaller irradiation volume and the higher dose rate. To reach a firm conclusion on the potential of nanocrystalline materials for nuclear reactor applications, extensive study of model metals with different stacking fault energy (SFE) is required to elucidate their behavior in radiation environments. Nanocrystalline copper and nickel are typically chosen because they are commonly used as model FCC metals in studies of radiation effects. Nickel is an FCC metal with a high stacking-fault energy (~125 mJ/m 2 ) compared to copper (~45 mJ/m 2 ). Hence, microcrystalline and nanocrystalline nickel samples were irradiated in the INL’s Advanced Test Reactor (ATR), as a part of FY08 North Carolina State University NSUF Irradiation Experiment# 96 to evaluate the irradiation behavior of these materials. The objective of this FY20 NSUF project# 19122 is to perform PIE (at PNNL NSUF facility) on previously ATR-neutron irradiated (1.2 and 2.6 dpa; 80-89°C) nanocrystalline and microcrystalline nickel samples to investigate the changes in mechanical properties and microstructures and evaluate whether nanocrystalline nickel is relatively more radiation resistant compared to conventional microcrystalline nickel. To perform PIE at PNNL, sixteen neutron irradiated specimens (microcrystalline and nanocrystalline) were transferred from the NSUF Nuclear Fuels and Materials Library at INL. Experimental techniques such as SEM/EBSD, XRD, TEM, Vickers microhardness and tensile testing were employed to characterize the effect of neutron irradiation on the microstructure and mechanical properties of nanocrystalline nickel and compared them with corresponding characteristics of microcrystalline nickel.

36 MATERIALS SCIENCE↗
NASA NTRS2023

Investigating the Role of Incident Ion Flux in Solar Wind Space Weathering of Carbon-Rich Asteroidal Regolith Via H+ and He+ Irradiation of the Murchison Meteorite

We present results from a set of low and high flux 1 keV/amu H + and He + irradiation experiments performed on slabs of the Murchison CM2 carbonaceous chondrite. The low flux conditions for H + and He + irradiation were ~1-1.5 orders of magnitude lower than the high flux conditions, and each experiment was irradiated to a total fluence between ~3 × 10 16 to ~6 × 10 16 ions/cm 2 . Irradiation-induced changes in the surface chemistry and optical properties of the Murchison samples were evaluated using in situ X-ray photoelectron spectroscopy (XPS) and visible and near-infrared spectroscopy (VNIR). We characterized the microstructure and composition of ion damaged rims in focused ion beam (FIB) cross-sections extracted from olivine and matrix material in each irradiated Murchison slab using transmission electron microscopy (TEM). XPS results suggest that both low flux and high flux H + and He + irradiation cause minor sputtering of surface carbon as well as a reduction in the valence state of iron, from Fe 3+ to Fe 2+ . Slope bluing is observed in VNIR spectra of the irradiated samples which may reflect carbonization and dehydrogenation of organic species and contrasts with reddening trends associated with npFe 0 formation. Although we do not observe a strong flux-dependence on the crystallinity of ion-damaged olivine, TEM analyses reveal a variety of microstructures in all olivine FIB-sections, suggesting that crystallographic orientation affects amorphization efficiency. Analyses of matrix FIB-sections indicate that phyllosilicate alteration is mainly driven by He+ irradiation, where the higher incident flux leads to greater amorphization and the formation of more distinct ion-damaged layers, similar to smooth layers in returned Ryugu particles. TEM results also provide some evidence that higher ion flux leads to greater vesiculation, with He + irradiation being more efficient at vesiculation than H + irradiation, and that higher ion flux may promote the segregation of Mg and Si into laterally extensive lenses and layers in olivine samples. We discuss the implications of these findings for constraining the role that ion flux plays in the development of space weathering characteristics in silicate phases present in carbonaceous asteroidal regoliths. These results will be important for understanding the complexity of this process and how it operates on carbon-rich airless bodies like asteroids Bennu and Ryugu.

meteorites↗
DOE OSTI2024

Promoting the regulatory acceptance of combined ion and neutron irradiation for material degradation in nuclear reactors

The Advanced Materials and Manufacturing Technologies (AMMT) program within the Department of Energy (DOE) Office of Nuclear Energy has developed its current recommendation for promoting the use of combined ion irradiation and neutron irradiation for the accelerated qualification of materials to be deployed in nuclear reactors. This plan is intended to provide a collaborative path forward that can be adopted by academia, national laboratories, and industry, and has been developed with input from the regulatory research arm of the U.S. Nuclear Regulatory Commission (NRC). To deploy new materials or materials manufactured with new technologies, such as additive manufacturing, materials must be evaluated for reactor-induced degradation from the combination of harsh temperatures, corrosive environments, and radiation fields. However, rapid deployment of materials necessitates accelerated testing methods rather than relying on years of neutron irradiation in a material test reactor. Ion irradiation has demonstrated success in reproducing material microstructure and select property evolution resulting from neutron irradiation with three to four orders of magnitude reduction in time and cost, making it an ideal candidate for accelerated irradiation testing. This presentation provides context governing both the scientific and regulatory aspects of the proposed goal. The discussion is aimed at a broad audience including researchers from industry, national laboratories, and academia. The recommended path forward is presented as a conceptual framework of specific steps. In brief, the strategy entails developing an integrated ion and neutron irradiation test plan for the material property of interest based on the fundamental tenet of the linkage of microstructure and properties in materials. Physics-based modeling interprets ion irradiation data and predicts neutron irradiation microstructure and properties with uncertainty bounds. The first round of testing is sufficient for an initial licensing application using a risk-informed approach, while a minimum required neutron irradiation test plan reduces cost and time requirements. A surveillance program with witness specimens in-reactor provides additional data over time to improve model predictions to higher damage levels and further reduce uncertainty bounds, which can be used for license extensions or longer lifetimes in new license applications.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Temperature Effects on Interdiffusion of Al and U-Mo under Irradiation

A high-energy Xe ion irradiation experiment was conducted to investigate the temperature dependence of interdiffusion in bilayer Al-UMo samples under irradiation. The amount of interdiffusion achieved at a fixed dose with the increase of temperature showed a clear transition at 175 degrees C (with an estimated error in the range of ± 10 degrees C) from temperature-independent to temperature-dependent behavior. The activation energy derived from the curve of interdiffusion quantity vs. irradiation temperature is 0.77 ± 0.16 eV. This information has been utilized to understand the temperature effect on the interdiffusion process that occurred at the interfaces of U-Mo particles and the Al matrix in U-Mo/Al dispersion fuels, whose magnitude significantly impacts the fuel's performance. Although this temperature effect was deemed important, it cannot be examined directly using in-pile irradiation data, as fuel temperatures cannot be measured in reactor irradiation and are highly correlated with fission rate and thermal conductivity evolution. To connect the knowledge accumulated from ion irradiation with in-pile irradiation data, simulation of a full-sized U-Mo/Al dispersion fuel plate irradiated in the FUTURE test in the BR2 reactor was performed with the Dispersion Analysis Research Tool (DART), a dispersion fuel performance code. DART is equipped with an interaction or interdiffusion layer (IL) growth correlation formulated to describe the temperature dependence of ion mixing results. The agreement between calculated and measured fuel meat constituent volume fractions and swelling data demonstrated that the temperature effect on in-pile Al-UMo interdiffusion is well captured with the correlation. In this case, the fitted activation energy is 0.70 eV. Considering the uncertainties associated with the ion irradiation data, the activation energy obtained from in-pile data fitting is in accord with that from ion irradiation results.

36 MATERIALS SCIENCE↗
DOE OSTI2025

The state of the art for neutron irradiation experiments from the perspective of the High Flux Isotope Reactor (HFIR)

Irradiation experiment campaigns are critical to advancing nuclear energy technologies by providing data on material performance under relevant radiation conditions. Successful irradiation experiments require integrated design efforts that balance technical goals with facility constraints. Here, this paper presents an expert-informed overview of irradiation experiment design at the High Flux Isotope Reactor. It addresses the nuclear materials research and irradiation experiment communities to guide them toward developing technically sound, facility-compatible campaigns. The High Flux Isotope Reactor is a multipurpose reactor supporting isotope production, neutron scattering, and materials testing. Its high, steady-state neutron flux is ideal for irradiation experiments, but successful execution demands coordinated thermal, structural, and reactor physics analyses. The paper outlines the complete development workflow from concept definition and design optimization to safety qualification and post-irradiation examination. Standardized capsule platforms are also discussed in terms of flexibility, specimen capacity, and thermal performance. Common failure modes such as unanticipated geometric variations, can impact temperature-dose profiles and compromise data reliability. Therefore, detailed thermal modeling and accurate as-built characterization are essential for meaningful post-irradiation data interpretation. Key recommendations include early engagement all stakeholders, clearly defined design expectations, and alignment of specimen geometries with post-irradiation examination capabilities. This approach reduces design iterations, enhances data quality, and supports more efficient use of irradiation resources. Strategic and well-planned irradiation testing not only improves individual campaign success but also accelerates the deployment of advanced nuclear technologies. By closing critical data gaps and reducing development risks, the nuclear materials community can more effectively contribute to the future of clean, resilient energy systems.

Experiments↗
DOE OSTI2026

HDG-1 Experiment Irradiation Monitoring Data Qualification Final Report

SUMMARY The U.S. Department of Energy (DOE) Advanced Reactor Technologies (ART) Graphite Research and Development (GRD) Program is conducting a series of six experiments to quantify the effects of irradiation on nuclear-grade graphite. This report documents the qualification of irradiation monitoring data for the fifth experiment, High Dose Graphite-1 (HDG-1). Qualified monitoring data are required by the ART program to support the design and licensing of the first high-temperature reactor (HTR) nuclear plant. Data are classified as Qualified if they meet the usage requirements described in the experiment planning and quality assurance (QA) documents, Failed if they do not meet those requirements and provide no usable information, or Trend if they do not fully meet all requirements but still provide useful information subject to an assessment of how any deficiencies may affect a particular use of the data. HDG-1 irradiation began with Advanced Test Reactor (ATR) Cycle 168B on August 24, 2020, and concluded after Cycle 173C on January 27, 2025. The HDG-1 capsule was removed from the reactor core twice—during core internal change (CIC) Cycle 170A and powered axial locator mechanism (PALM) Cycle 172A—to prevent overheating of the graphite specimens during high-power PALM cycles. The capsule was therefore irradiated during a total of seven normal ATR cycles: 168B, 169A, 171A, 171B, 173A, 173B, and 173C. Irradiation monitoring data evaluated in this report include thermocouple (TC) temperature, gas flow rate, gas moisture, gas pressure, specimen load, and graphite stack displacement. Temperature. A total of 14,508,065 TC temperature records were captured. Of these, 13,901,785 (95.8%) are Qualified and 606,280 (4.2%) are Failed. The principal source of failed temperature data was the instrument failure of TC-9 (Zone 2) on June 24, 2024, and TC-10 (Zone 1) on July 5, 2024, near the end of Cycle 173A, which resulted in 595,554 Failed readings. An additional 379 missing values and 10,347 slightly negative values from TC-13 during ATR outages are also Failed. Neither TC-9 nor TC-10 was used as a temperature-control TC, and their failures did not compromise capsule condition monitoring. Correlation analysis of all 13 TCs found no evidence of virtual junction formation. Control chart analysis revealed clear downward drift of approximately 80°C for TC-6 (Zone 3) relative to other stable TCs, and possible downward drift of approximately 60°C for TC-13 relative to the Zone 5 control TC (TC-1), though TC-13 remained consistent with the Zone 2 control TC (TC-12). Gas flow. A total of 20,088,090 gas flow rate records were captured. Of these, 19,941,463 (99.3%) are Qualified and 146,627 (0.7%) are Failed due to missing values. All argon, helium, and total gas flow data were within expected ranges throughout the irradiation. Gas moisture. A total of 1,116,005 outlet gas moisture values were captured. Of these, 1,101,421 (98.7%) are Qualified and 14,584 (1.3%) are Failed, comprising 14,556 out-of-range values and 28 missing values. The out-of-range moisture values exceeded 22,000 ppmv for approximately 1 week at the beginning of Cycle 173A, when accumulated moisture evaporated after the capsule was retrieved from water storage during PALM Cycle 172A and reinserted into the east flux trap. Moisture levels returned to below 25 ppmv for the remaining three cycles, and the transient high-moisture event did not affect the integrity of specimen irradiation. Gas pressure. A total of 7,812,035 gas pressure values were captured. Of these, 6,642,048 (85.0%) are Qualified and 1,169,987 (15.0%) outlet pressure values are Failed, comprising 718,537 zero outlet pressure values due to sensor failure from Cycle 168B through Cycle 171B, 54,550 missing values, and 396,900 too-low outlet pressure values, ranging from 1.1 to 1.6 psia after sensor replacement during Cycle 173A. Load. A total of 6,696,030 load values were captured. Of these, 6,694,580 (99.98%) are Qualified and 1,450 (0.02%) are Failed due to missing values. Applied loads to the six specimen stacks were stable throughout the irradiation. Stack displacement. A total of 6,696,030 displacement values were captured. Of these, 5,713,297 (85.32%) are Qualified and 3,781 (0.06%) are Failed due to missing values. Stack displacement increased consistently throughout the irradiation, reaching approximately 3.08 in. for Channels 5 and 6 by the end of irradiation. 978,952 (14.62%) substantially elevated displacements observed for Channel 6 beginning in Cycle 171A and for Channel 5 beginning in Cycle 173A are assigned Trend status. Raising pressure. A total of 1,115,999 raising pressure values were captured. Of these, 1,115,430 (99.95%) are Qualified and 569 (0.05%) are Failed due to missing values. Ram pressure. A total of 6,696,030 ram pressure values were captured. Of these, 6,692,249 (99.95%) are Qualified and 3,484 (0.05%) are Failed due to missing values. Stack raising was perf

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

In-situ irradiation-induced studies of grain growth kinetics of nanocrystalline UO 2

The thermal conductivity of UO 2 fuel needs to be high enough to dissipate the heat generated from the fission reaction. Since grain size affects thermal conductivity and grain size can evolve with irradiation, it is critical to understand in-reactor UO 2 grain growth. Most studies of grain growth in UO 2 are based on thermally driven processes at elevated temperatures. However, studies have shown that grain growth can occur even at cryogenic temperatures by ballistic processes. Such irradiation-induced grain growth in UO 2 is yet to be studied. Advanced in-situ Kr ion irradiation and transmission electron microscopy were systematically performed on nanocrystalline UO 2 thin films at temperatures ranging from 50 K to 1073 K; grain growth was observed at all temperatures. A combination of manual and machine learning techniques was used to measure and plot grain size evolution against irradiation fluence at various irradiation temperatures. The machine learning method has significantly improved the analysis efficiency and reduced human labors. The grain diameter data were fitted using classical grain growth and thermal spike models to describe grain growth kinetics with and without irradiation effect. Grain growth during low temperature irradiation (≤ 475 K) can be well described by the thermal spike model. Above 475 K, there were additional thermally assisted processes that further accelerate the grain growth. At the highest irradiation temperature about 1075 K, both irradiation-induced dislocation loops and cavities/bubbles were observed to form in the UO 2 . In this report, the effects of irradiation-induced defects on grain growth kinetics are discussed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Electronic energy loss and ion velocity correlation effects in track production in swift-ion-irradiated LiNbO3: A quantitative assessment between structural damage morphology and energy deposition

The primary motivation for studying how irradiation modifies the structures and properties of solid materials involves the understanding of undesirable phenomena, including irradiation-induced degradation of components in nuclear reactors and space exploration, and beneficial applications, including material performance tailoring through ion beam modification and defect engineering. In this work, the formation mechanism of latent tracks with different damage morphologies in LiNbO 3 crystals under 0.09–6.17 MeV/u ion irradiation with an electronic energy loss from 2.6–13.2 keV/nm is analyzed by experimental characterizations and numerical calculations. Irradiation-induced damage is preliminarily evaluated via the prism coupling technique to analyze the correlation between the dark-mode spectra and energy loss profiles of irradiated regions. Under the irradiation conditions of different ion velocities and electronic energy losses, different damage morphologies, from individual spherical defects to discontinuous and continuous tracks, are experimentally characterized. During ion penetration process, the ion velocity determines the spatiotemporal distribution of deposited irradiation energy induced by electronic energy loss, meaning that the two essential factors including electronic energy loss and ion velocity co-affect the track damage. The inelastic thermal spike model is used to numerically calculate the spatiotemporal evolutions of energy deposition and the corresponding atomic temperature under different irradiation conditions, and a quantitative relationship is proposed by comparison with corresponding experimentally observed track damage morphologies. Additionally, the obtained quantitative relationship between irradiation conditions and track damage provides deep insight and guidance for understanding the damage behavior of crystal materials in extreme radiation environments and selecting irradiation parameters, including ion species and energies, for ion beam technique application in atomic-level defect manipulation, material modification, and micro/nanofabrication.

36 MATERIALS SCIENCE↗
DOE OSTI2026

ROADRUNNER uranium nitride MiniFuel: Experimental design, fabrication and pre-irradiation baseline characterization for accelerated burnup testing

Uranium nitride (UN) is a promising fuel candidate for advanced reactor systems owing to its high uranium density and thermal conductivity; however, its qualification remains constrained by the scarcity of well-controlled irradiation performance data. Here, to address this limitation, the ROADRUNNER (Research On ADvancing the peRformance of UraNium Nitrides in Extreme enviRonments) campaign employs the MiniFuel platform in the High Flux Isotope Reactor (HFIR) to enable accelerated burnup irradiation testing under tightly controlled and largely isothermal conditions. This paper presents the experimental design, fuel fabrication, and pre-irradiation baseline characterization of the ROADRUNNER UN MiniFuel campaign. Thirty-six UN minidisc specimens were fabricated with systematically varied as-fabricated density (86–96% of theoretical density), carbon impurity content (961–5240 ppm), oxygen content (≤ ∼2000 ppm), and grain size (2.5–24 μm). The irradiation matrix spans nominal fuel temperatures of 873 K, 1173 K, and 1473 K and target burnups of 3.75%, 6.0%, and 7.5% fissions per initial metal atom (FIMA). Neutronic and thermal analyses were performed to define specimen-specific burnup accumulation and temperature histories, establishing the boundary conditions for subsequent in-pile behavior. Comprehensive pre-irradiation characterization—including dimensional metrology, density verification, impurity analysis, X-ray diffraction, Raman spectroscopy, scanning electron microscopy, X-ray computed tomography, and confocal profilometry—provides a detailed baseline for post-irradiation examination. Pre-irradiation data were further used to generate predictive estimates of fission gas release and swelling using existing empirical correlations. This quantitative comparison reveals substantial inter-model divergence at intermediate and elevated temperatures that exceeds propagated input uncertainties, highlighting structural gaps in the historical irradiation database. The ROADRUNNER irradiation campaign is currently underway in HFIR, with initial firs cycle completed in late 2025 and remaining targets scheduled through 2027. The experimental design and baseline dataset presented here establish the framework needed to interpret forthcoming post-irradiation measurements and to provide discriminating data for the validation and refinement of physics-based UN fuel performance models.

Lopes, Denise Adorno [Oak Ridge National Laborator↗
DOE OSTI2025

Tensile properties of the neutron irradiated HT-9 ACO-3 duct

HT-9, a ferritic-Martensitic steel, has attracted significant interest as a structural and cladding material for a variety of high dose nuclear component applications. This study examines the tensile properties of a HT-9 fuel assembly duct from the fast flux test facility, FFTF. The duct, from the Advanced Core Oxide-3 (ACO-3) irradiation test, was subjected to fast neutron irradiation exposure ranging from 3 dpa above the core top to nearly 155 dpa near the core mid-plane, spanning a temperature range from 382 °C at the lower end to 504 °C at the top. Due to the combination of thermal and neutron flux gradients along the core height. This yields a variety of irradiation damage processes which depend on core location. Tensile properties of specimens extracted at different positions along the height of the irradiated duct were measured at 25 °C, 200 °C and near their in-core irradiation temperature. The results show temperature has a greater impact than dose on post-irradiation strength and ductility. Two irradiation temperature regimes were determined, below irradiation temperatures of 420 °C irradiation hardening increases as irradiation temperature decreases, and above that temperature relatively minor changes are observed in tensile properties. These results are discussed in terms of expected microstructural changes, indicating that dislocation content is a strong contributor in these findings.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Phase Transformation of Thermally Aged and Neutron Irradiated Duplex Stainless Steel Used in LWRs. Final report

The lifetime of reactor components made of duplex stainless steels can be limited by the embrittlement from thermal aging, neutron irradiation or a synergistic effect between thermal aging and neutron irradiation. There is still a large scientific knowledge gap in understanding the phase evolution in duplex stainless steels upon thermal aging with or without neutron irradiation, the synergistic effect between thermal aging and neutron irradiation, and the impacts of structural evolution on material mechanical responses. In this project, totally, five major tasks were completed through this project: a) the in-situ WAXS tensile tests of thermally aged cast duplex stainless steels, b) the EXAFS investigation of thermally aged cast austenitic stainless steel and welds of austenite sainless steel, c) the characterization of irradiation effect on neutron irradiated CASS using APT, d) characterize the ferrite hardening of neutron irradiated CASS using nanoindentation, and e) the FEM modelling to validate the in-situ WAXS tensile tests and to simulate the stress/strain distribution during deformation for thermally aged duplex stainless steel. In summary, the thermal aging without neutron irradiation can significantly increase the strength of ferrite phase through the spinodal decomposition and G-phase precipitations. The in-situ X-ray experiments show that the hardening effect in ferrite phase can significantly alter the load partition between the ferrite and austenite phases. Atom probe tomography characterizations on samples irradiated to 0.08, 3, 5, 10, 20, and 40 dpa shows that neutron irradiation has dominated the microstructural evolution after 3 dpa, and the spinodal decomposition has saturated yet even at 40 dpa based on the quantified wavelength and amplitude.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Summary of the Postirradiation Examination of the First Samples from a MiniFuel Irradiation

An overview of postirradiation examination results for uranium nitride kernels and uranium nitride coated particles irradiated in the High Flux Isotope Reactor are presented. This is the first postirradiation examination of the MiniFuel irradiation vehicle that was recently developed to rapidly screen different nuclear fuel concepts. Observations on fission gas release, irradiation conditions and microstructure of the irradiated fuel show good fuel performance at the low burnup achieved in this initial irradiation. The burnup measured by mass spectrometry ranged from 5.9 to 10 MWd/kgU as was achieved after only 68 effective full power days of irradiation. Results from silicon carbide thermometry measurements further benchmarked the MiniFuel irradiation vehicle and indicated fuel was irradiated at temperatures ranging from 410-460°C. Extensive microstructural characterization on the irradiated fuel was performed and no significant irradiation induced changes were observed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Impact of Irradiation and Decay Time on Chemical Speciation in Uranyl Sulfate Solution

A pH-1, 200-g U/L, highly enriched uranyl sulfate solution was neutron-irradiated using an accelerator-driven neutron source (the Universal Neutron Irradiator, UNI) to fission U-235 under conditions similar to those used by SHINE to produce Mo-99 in a subcritical assembly. We completed a series of five uranyl sulfate irradiations to assess the impact of irradiation and decay time on uranium precipitation and iodine speciation in solution. The duration of each irradiation was increased in order, with the shortest irradiation taking 2.9 hours and the longest, 64.5 hours. A total of 9.5E16 U-235 nuclei were fissioned in all irradiations, and a maximum fission power density of 0.26 W/mL was reached in the final irradiation. We observed no evidence of uranyl peroxide or other precipitates, demonstrating that the addition of Fe 2+ to a final Fe concentration of 200 ppm in the target solution was successful at preventing precipitation under representative irradiation conditions. Nonvolatile I - was found to be the dominant (>70%) iodine species in solution, both immediately after irradiation and after days to weeks of decay time.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗