SEARCH · Engineering Papers

Results for “INJECTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

All sources NASA NTRS DOE OSTI

DOE OSTI2021

The effects of laser polarization and wavelength on injection dynamics of a laser wakefield accelerator

Here, we investigate the effects of laser polarization and wavelength on electron injection dynamics in a laser wakefield accelerator. During the ionization process, electrons gain residual momentum and kinetic energy via above threshold ionization, which has a strong dependence on laser polarization. A circularly polarized laser pulse results in a much higher residual momentum and kinetic energy gain for the ionized electrons compared with the linearly polarized case. This residual momentum results in particle injection because of the sensitivity of particle trapping to the initial conditions and enhanced the total injected beam charge in both experiments and particle-in-cell simulations. Due to the strong correlation of above threshold ionization with laser wavelength, in this work we extended the investigation to long wavelength (up to 20 μm) drive pulses using particle-in-cell simulations. Owing to the gain in kinetic energy, it may be expected that the charge trapped would consistently increase for circular polarization with increasing laser wavelength, but this was not observed. Instead, there are oscillations with wavelength in the relative trapped charge between linear and circular polarization cases, which arise because of ionization and heating effects on the plasma. Our studies highlight the complex interplay between several different physical effects, including injection regimes—above threshold ionization assisted injection, wave-breaking injection by carrier-envelope-phase effects and ionization injection—ionization gradient induced laser pulse evolution, and thermal modifications to the wake structure that need considering when extrapolating laser wakefield acceleration to different wavelength regimes.

Ma, Y. (ORCID:0000000239194856)↗

DOE OSTI2020

Backscatter-Immune Injection-Locked Brillouin Laser in Silicon

As self-sustained oscillators, lasers possess the unusual ability to spontaneously synchronize. These nonlinear dynamics are the basis for a simple yet powerful stabilization technique known as injection locking, in which a laser’s frequency and phase can be controlled by an injected signal. Because of its inherent simplicity and favorable noise characteristics, injection locking has become a workhorse for coherent amplification and high-fidelity signal synthesis in applications ranging from precision atomic spectroscopy to distributed sensing. Within integrated photonics, however, these injection-locking dynamics remain relatively untapped—despite significant potential for technological and scientific impact. In this work, we demonstrate injection locking in a silicon photonic Brillouin laser. Injection locking of this monolithic device is remarkably robust, allowing us to tune the laser emission by a significant fraction of the Brillouin gain bandwidth. Harnessing these dynamics, we demonstrate amplification of small signals by more than 23 dB. Moreover, we demonstrate that the injection-locking dynamics of this system are inherently nonreciprocal, yielding unidirectional control and backscatter immunity in an all-silicon system. This device physics opens the door to strategies for phase-noise reduction, low-noise amplification, and backscatter immunity in silicon photonics.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2025

Investigating the Combustion Performance of Dual Fuel Combustion with Diesel and Port Injected Hydrogen in a Large Bore Locomotive Engine

The heavy-duty transportation sector has primarily relied on conventional diesel combustion engines given their reliability and high thermal efficiency relative to spark ignition engines, but increased focus on reducing greenhouse gas emissions has led to investigation into alternative fuels. Gaseous hydrogen fuel has garnered a great deal of recent interest in the engine community given it has zero carbon, but hydrogen is not available at the scale and cost that petroleum fuels are currently available, and this is a barrier to adoption for industries that are looking to decarbonize their operations. Because of the fuel flexibility provided, dual fuel technology offers a pathway for some industries to adopt hydrogen as a fuel source while maintaining sufficient flexibility in times and locations where the new fuel is not yet available. This computational study investigates dual fuel combustion in a large bore locomotive engine architecture using direct injected diesel and port injected gaseous hydrogen fuel. With an optimal port fuel injection configuration from previous work, simulations of varying substitution ratio, compression ratio, manifold air temperature, diesel injection timing, and diesel injection pressure were performed to understand their effect on combustion performance. Results indicated that both increased substitution ratio and higher intake air temperature accelerates hydrogen flame propagation and can result in high peak cylinder pressures. Additionally, diesel injection timing and injection pressure were demonstrated as effective methods for controlling dual fuel combustion heat release rates.

ODonnell, Patrick Christopher↗

DOE OSTI2020

Analysis of Microseismicity and Reactivated Fault Size to Assess the Potential for Felt Events by CO 2 Injection in the Illinois Basin

The results of monitoring of carbon dioxide (CO 2 ) injection at the Illinois Basin—Decatur Project (IBDP) and the companion Illinois Industrial Carbon Capture and Sequestration Sources (IL-ICCS) project—have shown that reservoir response to fluid pressure changes can vary significantly at different injection locations within the same reservoir. Predrill reservoir characterization is important to identify potentially seismogenic faults. However, interpretations of newly reprocessed 3D seismic reflection data illustrate the challenges related to their identification in a region dominated by faulting with small vertical offsets. Faults interpreted in the 3D seismic volume range from ~300 to 1200 m wide and are in the same size range as faults that could have been the source of historical events up to Mw 2.7 in central Illinois. The array of monitoring sensors that was installed for the IBDP continues to collect data, as injection operates in IL-ICCS, the second injection well. CO 2 injection rates for the IL-ICCS well are on average 1.7 times the rates injected in the IBDP well, but a significantly reduced rate of induced seismicity is observed. This article presents results of passive seismic monitoring for the duration of the project to date, integrating active and passive seismic data to develop a new interpretation of the subsurface structure at the Decatur site that explicitly identifies pathways for fluid flow into the basement leading to induced seismicity, and provides a geological explanation for the sharp reduction of induced seismicity during injection at higher rates into the second well. The use of seismic moment to estimate the length of seismogenic slip planes in the local subsurface suggests that faults large enough to produce felt seismicity are unlikely to be present at or near the Decatur site.

Geochemistry & Geophysics↗

DOE OSTI2020

Distributed Acoustic Sensing (DAS) Seismic Monitoring of CO 2 Injected for Enhanced Oil Recovery in Northern Michigan (Volume II.C)

The Midwest Regional Carbon Sequestration Partnership (MRCSP) was founded in 2003 as part of the U.S. Department of Energy’s (DOE’s) Regional Carbon Sequestration Partnership initiative. Since its founding, MRCSP has made significant strides toward making CCUS a viable option for states in the region. The public/private consortium, funded through the DOE Regional Carbon Sequestration Initiative, brings together nearly 40 industry partners and 10 states. Battelle, as the project lead, oversees research, development and operations and coordinates activities among the partners. The incremental, phased approach has built a valuable knowledge base for the industry and paved the way for commercial-scale adoption of CCUS technologies. From 2008 to 2020, MRCSP Phase III focused on the development of large-scale injection projects. This report is part of a series of reports prepared under the Midwestern Regional Carbon Sequestration Partnership (MRCSP) Phase III (Development Phase). These reports summarize and detail the findings of the work conducted under the Phase III project. This report describes the monitoring study conducted to assess the effectiveness of DAS (Distributed Acoustic Sensing) -based VSP (Vertical Seismic Profiling) technology for delineating CO 2 injected into the Silurian-age pinnacle reefs in northern Michigan, the host rocks for the MRCSP Phase III demonstration project. The DAS VSP study was conducted in the Chester 16 reef, one of several reefs in Otsego County Michigan that is operated by Core Energy, LLC of Traverse City, Michigan. Time-lapse DAS VSP was implemented at the Chester 16 reef to attempt to detect approximately 85,000 tonnes of CO 2 injected into the A-1 Carbonate and Brown Niagaran Formations. A baseline survey was conducted in February 2017 prior to injecting CO 2 and a repeat survey was conducted in August 2018. During the interim period between the baseline and repeat surveys, CO 2 was injected into the Chester 16 reef via the 6-16 injection well without production (withdrawal) of fluids from the reef. A grid of 181 source positions consisting of 44 vibrator positions, plus 137 dynamite shot locations, was used to give approximately continuous spatial coverage of the injection zone (A-1 Carbonate and upper Brown Niagaran) in the area between the two wells.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2021

Online Optimization of NSLS-II Dynamic Aperture and Injection Transient (Facility Improvement Project)

The Facility Improvement Project (FIP) “Methods of online optimization of NSLS-II storage ring concurrent with user operations” proposed and approved in 2018 is now complete. The first goal is the online optimization of nonlinear beam dynamics to increase the beam lifetime and injection efficiency. We have developed a model-independent optimization technique using advanced algorithms. Using this technique, we increased the NSLS-II dynamic aperture by 20% and reduced the amplitude-dependent tune shift by a factor of two. We applied sextupole optimization to the new high-chromaticity lattice, which has been developed to improve the beam stability and to increase the single-bunch beam intensity. We were able to double the injection efficiency and exceed 90%. The second goal of this project is to provide the top-off injection with minimized perturbations of the beamline user operations. To achieve the transparent injection, we optimize the matching of four storage ring injection kickers reducing the perturbation of the stored beam orbit. The first application of the online optimization resulted in a reduction of the amplitude of residual beam oscillation by a factor of six, from 1300 μm down to 200 μm. Further improvement was limited by the timing jitter of the trigger boards. Then, we replaced all trigger boards with a new design and reduced the timing jitter by a factor of five, from 5 ns down to 1 ns. This upgrade resulted in the injection transient reduction from 200 μm to 120 μm. To optimize the full set of kicker parameters, including the trigger timing, amplitude, and pulse width, we upgraded all kicker power supplies with the capability of tunable waveform width. As a result, we have reduced the injection transient to the limit of 60 μm.

43 PARTICLE ACCELERATORS↗

DOE OSTI2022

Controlled Injection of Electrons for Improved Performance of Laser-Wakefield Acceleration

Our lab performed a series of experiments on controlled injection of LWFA with two extreme laser pulses: one laser pulse was used to drive LWFA. In contrast, the other precisely controls the injection of electrons into the wakefield plasma wave. We have demonstrated an efficient reduction of electron beam emittance by optical injection and novel spatio-temporal manipulation of the electron beam by the extreme laser-plasma waves. Moreover, the optical injection process involves unprecedented new physics, which will benefit studies in astrophysics, inertial confinement fusion, laser-driven x-ray light sources, and ultrafast science. We further improved the performance of LWFA by a better understanding and control of the extreme laser-plasma wave dynamics for optical injection. Three novel mechanisms were identified in the optical injection process: (1) collision of two laser pulses, (2) collision of a laser pulse with a wakefield plasma wave, and (3) collision of two laser wakefields. All three methods improved electron-beam energy spread, emittance, stability, and reproducibility. First, we identified, compared, and independently controlled these different injection mechanisms by controlling the polarization of the injector laser pulse. Second, we manipulated the spatiotemporal splitting of LWFA electron beams to reduce their emittance. Third, we applied the same laser-plasma-wave dynamics and the same experimental setup for improved performance of ion acceleration, which has also been predicted by the recent simulations.

43 PARTICLE ACCELERATORS↗

DOE OSTI2023

Assessment of Carbonated Brine Injection as Low-risk Strategy for Geologic Carbon Storage

The main objective of this early-phase research was to evaluate the techno-economic feasibility and risk associated with combined brine and CO 2 storage in SWD wells using brine dissolution in the North Dakota portion of the Williston Basin. Three simulation studies were conducted to investigate: (1) CO 2 phases at different conditions, (2) wellbore compatibility, and (3) long-term storage fate in reservoir. (1) A simple reservoir model and injection simulations were created using data to represent the BEST (brine extraction and storage test) site, an operational SWD facility located near Watford City, North Dakota. The pressure evolution caused by CO 2 comingled in produced water injectate in a layer cake reservoir was then modeled while tracking aqueous CO 2 throughout the project. The salinity of the injection water, the salinity of the reservoir brine, and the amount of dissolved CO 2 comingled in the injection water were varied. (2) A wellbore corrosion model was performed using the CO 2 concentrations selected based on the reservoir modeling to examine the carbonated produced water impact on wellbore. (3) Reactive transport modeling was conducted with the optimal CO 2 concentration for this injection site to study the rock-fluid interactions and CO 2 fate in the reservoir. Results suggest that CO 2 dissolved in produced water can be injected without appreciably increasing subsurface pressure or leakage risks. Pressure buildup was found to vary with salinity but not with CO 2 mass fraction. Simulation results show that lower CO 2 percent mass fraction leads to a higher amount of CO 2 that can be dissolved at a higher injection salinity. Furthermore, the long-term goal of dissolution trapping in a traditional carbon storage project is accomplished from the start, mitigating risks associated with potential migration of buoyant CO 2 , so long as the reservoir pressure and temperature are used to determine the maximum mass fraction of the dissolved CO 2 .

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2023

Exploration of Fuel Property Impacts on the Combustion of Late Post Injections Using Binary Blends and High-Reactivity Ether Bioblendstocks

In this study, the impacts of fuel volatility and reactivity on com- bustion stability and emissions were studied in a light-duty single- cylinder research engine for a three-injection catalyst heating oper- ation strategy with late post-injections. N-heptane and blends of farnesane/2,2,4,4,6,8,8-heptamethylnonane were used to study the im- pacts of volatility and reactivity. The effect of increased chemical reac- tivity was also analysed by comparing the baseline #2 diesel operation with a pure blend of mono-ether components (CN > 100) representa- tive of potential high cetane oxygenated bioblendstocks and a 25 vol.% blend of the mono-ether blend and #2 diesel with a cetane number (CN) of 55. At constant reactivity, little to no variation in combustion performance was observed due to differences in volatility, whereas in- creased reactivity improved combustion stability and efficiency at late injection timings. Fuels with higher reactivity were found to reduce engine-out hydrocarbon and carbon monoxide emissions while also achieving stable combustion at post-injection timings later than those achievable with #2 diesel fuel. The pure ether blend had the latest achievable post-injection timing of +30.5 CAD while still maintaining stable combustion (coefficient of variation of gross-indicated mean ef- fective pressure < 5%). With post-injection timing adjusted to achieve a matched exhaust temperature of 300 °C, the ether-diesel CN 55 blend was observed to have slightly higher thermal efficiency in comparison to the baseline #2 diesel fuel. The results also indicate that cetane num- ber may serve as a good indicator of combustion characteristics at late injection timings used for aftertreatment thermal management opera- tion.

99 GENERAL AND MISCELLANEOUS↗

DOE OSTI2023

Exploration of Fuel Property Impacts on the Combustion of Late Post Injections Using Binary Blends and High-Reactivity Ether Bioblendstocks

In this study, the impacts of fuel volatility and reactivity on combustion stability and emissions were studied in a light-duty single-cylinder research engine for a three-injection catalyst heating operation strategy with late post-injections. Here, N-heptane and blends of farnesane/2,2,4,4,6,8,8-heptamethylnonane were used to study the impacts of volatility and reactivity. The effect of increased chemical reactivity was also analysed by comparing the baseline #2 diesel operation with a pure blend of mono-ether components (CN > 100) representative of potential high cetane oxygenated bioblendstocks and a 25 vol.% blend of the mono-ether blend and #2 diesel with a cetane number (CN) of 55. At constant reactivity, little to no variation in combustion performance was observed due to differences in volatility, whereas increased reactivity improved combustion stability and efficiency at late injection timings. Fuels with higher reactivity were found to reduce engine-out hydrocarbon and carbon monoxide emissions while also achieving stable combustion at post-injection timings later than those achievable with #2 diesel fuel. The pure ether blend had the latest achievable post-injection timing of +30.5 CAD while still maintaining stable combustion (coefficient of variation of gross-indicated mean effective pressure < 5%). With post-injection timing adjusted to achieve a matched exhaust temperature of 300 °C, the ether-diesel CN 55 blend was observed to have slightly higher thermal efficiency in comparison to the baseline #2 diesel fuel. The results also indicate that cetane number may serve as a good indicator of combustion characteristics at late injection timings used for aftertreatment thermal management operation.

09 BIOMASS FUELS↗

NASA NTRS1964

Injection and distribution of liquids in the flow fields of blunt shapes at hypersonic speeds

A possible method for reducing the attenuation of radio transmission from hypersonic vehicles is by injection of a liquid into the flow field. The hot plasma layer surrounding the vehicle could presumably be quenched if the latent heat of the liquid and the heat capacity of the vapor could be utilized efficiently. In the case of stagnation-point injection, the momentum of the liquid could be utilized to modify the bow shock and possibly reduce the initial ionization. To attain these objectives of efficient coolant utilization or modification of the bow shock a knowledge of the liquid injection, atomization, spray penetration, and evaporation processes is required. This report presents the results of a study of liquid injection into hypersonic flow fields. A simplified theory for evaporation distances is derived and is shown to be in qualitative agreement with experimental data. Correlation of experimental data for maximum cross-current penetration of the liquid spray for injection near the shoulder pf a hemisphere cylinder, a sphere 9° cone, and a Mercury model are given. These data were obtained in the Langley Mach 8 variable density tunnel with both liquid nitrogen and water injection to provide a large range of liquid parameters. Flow-field disturbances, as indicated by schlieren photographs and surface pressures, increased with the ratio of coolant mass flux to airstream mass flux. For stagnation-point injection, the maximum shock standoff distance was correlated by the ratio of the liquid jet momentum flux to the airstream momentum flux.

Ivan E. Beckwith↗

NASA NTRS1972

The effect of injection angle on the interaction between sonic secondary jets and a supersonic free stream

An experimental investigation, as part of a research program on the development of technology for the design of supersonic combustion ramjets, has been conducted to determine the effect of injection angle on the jet penetration, mixing rate, and airstream total-pressure recovery downstream of five laterally spaced sonic hydrogen jets flush mounted on a flat plate. Results of this investigation indicated that at lower injection angles less free-stream momentum loss was required to turn and accelerate the injected gas downstream and, thereby, less flow disturbance and total-pressure loss were produced. In addition, lower injection angles resulted in improved fuel distribution and faster mixing of the injected gas with the free stream. A correlating parameter, developed from considerations of the effective-momentum-flux differences between the injected gas and the free-stream air, predicted greater penetration and faster mixing for the lower injection angles.

Mcclinton, C. R.↗

NASA NTRS1976

Plasma injection at synchronous orbit and spatial and temporal auroral morphology

Analysis of ATS 5 particle spectrograms and simultaneous meridian-scanning photometer data obtained at the base of the ATS field line has revealed systematic relationships between temporal and spatial auroral morphology and particle-injection events. The details of these relationships depend on previous injection events, the local time of the observatory with respect to current-injection events, and the extent and magnitude of current injections. A persistent zone of weak aurora is related to steady plasma-sheet drizzle, and the equatorward edge of this aurora delineates field lines threading the inner edge of the plasma sheet. Auroras associated with injection events superimpose on this preexisting pattern, with the lowest latitude of new precipitation depending on local time. In general, plasma energization is not required between the equatorial plane and the ionosphere to account for observed auroral intensities. The data indicate occasional occurrence of enhanced loss-cone fluxes, suggesting low-altitude field-aligned acceleration. A summary figure shows how various characteristic auroral-precipitation regions are related to the shape, extent, and orientation of the substorm injection boundary and to the subsequent drift paths of injected plasma.

Eather, R. H.↗

NASA NTRS1976

Heat transfer to a full-coverage film-cooled surface with 30 degree slant-hole injection

Heat transfer behavior was studied in a turbulent boundary layer with full coverage film cooling through an array of discrete holes and with injection 30 deg to the wall surface in the downstream direction. Stanton numbers were measured for a staggered hole pattern with pitch-to-diameter ratios of 5 and 10, an injection mass flux ratio range of 0.1 to 1.3, and a range of Reynolds number Re sub x of 150,000 to 5 million. Air was used as the working fluid, and the mainstream velocity varied from 9.8 to 34.2 m/sec (32 to 112 ft/sec). The data were taken for secondary injection temperature equal to the wall temperature and also equal to the mainstream temperature. The data may be used to obtain Stanton number as a continuous function of the injectant temperature by use of linear superposition theory. The heat transfer coefficient is defined on the basis of a mainstream-to-wall temperature difference. This definition permits direct comparison of performance between film cooling and transpiration cooling. A differential prediction method was developed to predict the film cooling data base. The method utilizes a two-dimensional boundary layer program with routines to model the injection process and turbulence augmentation. The program marches in the streamwise direction, and when a row of holes is encountered, it stops and injects fluid into the boundary layer. The turbulence level is modeled by algebraically augmenting the mixing length, with the augmentation keyed to a penetration distance for the injected fluid.

Crawford, M. E.↗

NASA NTRS1977

Solar wind plasma injection at the dayside magnetospheric cusp

Two mechanisms have been proposed for solar wind particle injection at the dayside magnetospheric cusps: magnetic merging and cross-field diffusion. These two mechanisms are experimentally distinguishable in that they produce different latitudinal distributions of particles penetrating to the low-altitude cusp. An examination of proton and electron measurements obtained by the AE-C satellite in the low-altitude dayside cusp reveals evidence of both types of injection processes. A majority of the injection events, especially the more intense fluxes, are best explained by a merging injection model in which cusp particles are confined to the poleward side of the last closed field line and have a characteristic energy that decreases with increasing latitudinal distance from the last closed field line. Less frequent and less intense injection events are better explained in terms of a diffusive injection of cusp particles onto closed dayside field lines with a characteristic energy that increases with increasing latitudinal distance from the last closed field line. Although diffusion appears to be quantitatively less important than merging in terms of the instantaneous particle injection rate, cross-field diffusion nevertheless appears to proceed at an unexpectedly fast rate, possibly exceeding the Bohm diffusion limit.

Reiff, P. H.↗

NASA NTRS1980

The physics of plasma injection events

In this paper, plasma injection is defined as an increase of particle flux in a detector of finite bandwidth. Injection can result from dynamic processes or from spacecraft penetration of a quasi-static spatial structure produced by a steady magnetospheric convection pattern. ATS-5 particle spectrograms are found to provide examples of plasma injection events of both sorts. Dynamic injection occurs both with and without local magnetic signatures. For events not associated with clear local magnetic signatures, convection theory with a steady or a time-varying uniform electric field can account for the energy dispersion of injected particles with energy less than 50 keV. The paper concludes with a discussion of the way in which the convection boundaries are related to the substorm injection boundary of Mauk and McIlwain. Several alternative expressions for the local time and K(p) dependence of the injection boundary are given.

Kivelson, M. G.↗

NASA NTRS1991

Navier-Stokes calculations for 3D gaseous fuel injection with data comparisons

Results from a computational study and experiments designed to further expand the knowledge of gaseous injection into supersonic cross-flows are presented. Experiments performed at Mach 6 included several cases of gaseous helium injection with low transverse angles and injection with low transverse angles coupled with a low yaw angle. Both experimental and computational data confirm that injector yaw has an adverse effect on the helium core decay rate. An array of injectors is found to give higher penetration into the freestream without loss of core injectant decay as compared to a single injector. Lateral diffusion plays a major role in lateral plume spreading, eddy viscosity, injectant plume, and injectant-freestream mixing. Grid refinement makes it possible to capture the gradients in the streamwise direction accurately and to vastly improve the data comparisons. Computational results for a refined grid are found to compare favorably with experimental data on injectant overall and core penetration provided laminar lateral diffusion was taken into account using the modified Baldwin-Lomax turbulence model.

Fuller, E. J.↗

NASA NTRS2005

Impulsive Injection for Compressor Stator Separation Control

Flow control using impulsive injection from the suction surface of a stator vane has been applied in a low speed axial compressor. Impulsive injection is shown to significantly reduce separation relative to steady injection for vanes that were induced to separate by an increase in vane stagger angle of 4 degrees. Injected flow was applied to the airfoil suction surface using spanwise slots pitched in the streamwise direction. Injection was limited to the near-hub region, from 10 to 36 percent of span, to affect the dominant loss due to hub leakage flow. Actuation was provided externally using high-speed solenoid valves closely coupled to the vane tip. Variations in injected mass, frequency, and duty cycle are explored. The local corrected total pressure loss across the vane at the lower span region was reduced by over 20 percent. Additionally, low momentum fluid migrating from the hub region toward the tip was effectively suppressed resulting in an overall benefit which reduced corrected area averaged loss through the passage by 4 percent. The injection mass fraction used for impulsive actuation was typically less than 0.1 percent of the compressor through flow.

Culley, Dennis E.↗