Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “II&C”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Diffuse Bands 9577 and 9633: Relations to Other Interstellar Features

We study, for the first time, the relations of two strong diffuse bands (DIBs) at 9633 and 9577 Å, commonly attributed to C{sub 60}{sup +}, to other interstellar features seen in optical and UV spectra including H i, Ca i, Fe ii, Na i, Ti ii, CN, CH, CH{sup +}, and C{sub 2} and DIBs 5780, 5797, 6196, 6269, 6284, and 6614. We analyzed 62 lines of sight where the stellar contamination by Mg ii was corrected or found negligible for DIB 9633. Equivalent widths of DIB 9577 were measured in 62 lines of sight. Poor mutual correlation between the strengths of the above features and the major diffuse bands (5780 and 5797) as well as with other DIBs (with some exceptions) were revealed. The considered DIBs are also poorly correlated with the features of neutral hydrogen, molecular carbon, and those of simple interstellar radicals. Perhaps this phenomenon can be explained if the diffuse band 9577 is an unresolved blend of two or more interstellar features. There are indications that 9633 and 9577 diffuse bands are stronger in σ-type clouds, i.e., these features resemble the behavior of reasonably broad DIBs, which are strong in the lines of sight where the UV flux from the very hot nearby stars plays an important role.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Lowering oxygen evolution overpotential via morphology control of NiO x nanocatalysts

NiO x nanocatalysts with two distinct morphologies, nano-spindles and nano-plates, were synthesized and evaluated for oxygen evolution reaction (OER) performance. Spindle-like NiO x was prepared via a hydrothermal reaction of nickel nitrate and urea with cetyltrimethylammonium bromide as a surfactant at 120 °C for 24 h, forming Ni(OH) 2 -based intermediates that were subsequently calcined at 300 °C for 3 h. In contrast, platelet-like Ni(OH) 2 nanocrystals were obtained using nickel(II) acetate and KOH at 180 °C for 24 h, followed by calcination at 400 °C or 500 °C for 4 h to yield NiO x nano-plates. The NiO x nano-spindles exhibited an OER overpotential of 395 mV at 10 mA/cm 2 , whereas the NiO x nano-plates annealed at 400 °C and 500 °C showed overpotentials of 565 mV and 474 mV at 10 mA/cm 2 , respectively. Structural characterization and X-ray photoemission spectroscopy indicate these differences arise from morphology-dependent surface structures that govern catalytic activity.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Structures of five salt forms of disulfonated monoazo dyes

The structures of five s -block metal salt forms of three disulfonated monoazo dyes are presented. These are poly[di-μ-aqua-diaqua[μ 4 -3,3'-(diazane-1,2-diyl)bis(benzenesulfonato)]disodium(I)], [Na 2 (C 12 H 8 N 2 O 6 S 2 )(H 2 O) 4 ] n , (I), catena -poly[[tetraaquacalcium(II)]-μ-3,3'-(diazane-1,2-diyl)bis(benzenesulfonato)], [Ca(C 12 H 8 N 2 O 6 S 2 )(H 2 O) 4 ] n , (II), catena -poly[[[diaquacalcium(II)]-μ-2-(4-amino-3-sulfonatophenyl)-1-(4-sulfonatophenyl)diazenium] dihydrate], {[Na(C 12 H 10 N 3 O 6 S 2 )(H 2 O) 2 ]·2H 2 O} n , (III), hexaaquamagnesium bis[2-(4-amino-3-sulfonatophenyl)-1-(4-sulfonatophenyl)diazenium] octahydrate, [Mg(H 2 O) 6 ](C 12 H 10 N 3 O 6 S 2 ) 2 ·8H 2 O, (IV), and poly[[{μ 2 -4-[2-(4-amino-2-methyl-5-methoxyphenyl)diazen-1-yl]benzene-1,3-disulfonato}di-μ-aqua-diaquabarium(II)] dihydrate], {[Ba(C 14 H 13 N 3 O 7 S 2 )(H 2 O) 4 ]·2H 2 O} n , (V). Compound (III) is that obtained on crystallizing the commercial dyestuff Acid Yellow 9 [74543-21-8]. The Mg species is a solvent-separated ion-pair structure and the others are all coordination polymers with bonds from the metal atoms to sulfonate groups. Compound (I) is a three-dimensional coordination polymer, (V) is a two-dimensional coordination polymer and both (II) and (III) are one-dimensional coordination polymers. The coordination behaviour of the azo ligands and the water ligands, the dimensionality of the coordination polymers and the overall packing motifs of these five structures are contrasted to those of monosulfonate monoazo congers. It is found that (I) and (II) adopt similar structural types to those of monosulfonate species but that the other three structures do not.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Densification of non-radioactive porous siliceous particles loaded with cesium potassium copper hexacyanoferrate by spark plasma sintering

In the development of a conditioning process for cesium-bearing sorbents from the decontamination of aqueous waste streams, the treatment of a granular material composed of (Cs,K) 2 CuFe(CN) 6 loaded onto mesoporous silica particles has been investigated in an additive-free two-step conditioning process involving (i) calcination at 1000 °C to remove volatile species and (ii) densification by spark plasma sintering. A 92.0 % dense pellet was obtained after 10 min sintering at 850 °C under 100 MPa. Density and microstructural measurements indicate that densification is first driven by the viscous flow of a vitreous phase containing Cs, formed during calcination. Additionally, the density of the sample then increases further during sintering by grain boundary diffusion. However, a limited but non negligible part of cesium is lost during densification.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Measurement of the branching fraction and CP asymmetry of B 0 →π 0 ⁢π 0 decays using 198×1⁢0 6 $B\overline{B}$ pairs in Belle II data

We report measurements of the branching fraction and C P asymmetry in B 0 → π 0 π 0 decays reconstructed at Belle II in an electron-positron collision sample containing 198 × 10 6 B B ¯ pairs. We measure a branching fraction B ( B 0 → π 0 π 0 ) = ( 1.38 ± 0.27 ± 0.22 ) × 10 - 6 and a C P asymmetry A C P ( B 0 → π 0 π 0 ) = - 0.14 ± 0.46 ± 0.07 , where the first uncertainty is statistical and the second is systematic.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2023

Force-Modulated C–C Reductive Elimination from Nickel Bis(polyfluorophenyl) Complexes

We have analyzed the rate of C(sp 2 )–C(sp 2 ) reductive elimination from nickel(II) bis(2,4,6-trifluorophenyl) complex-es (P–P)Ni(2,4,6-C 6 H 2 F 3 ) 2 containing either MeOBiPhep (3a) or macrocyclic bisphosphine ligand (3b-3e) as a func-tion of force applied to the biaryl backbone of these ligands through intramolecular tension generated by a molecular force probe. Nickel complexes 3 were isolated in 22-60% yield from reaction of bisphosphine with the bis(tetrahydrofuranyl) complex (THF) 2 Ni(2,4,6-C 6 H 2 F 3 ) 2 followed by chromatography. Thermolysis of complexes 3 in C 6 D 6 at 68 °C leads to first-order decay through > 3 half-lives to form 2,2',4,4',6,6'-hexaflurorobiphenyl as the exclusive fluorine-containing product in ≥93% yield. Whereas compressive forces up to –65 pN have no significant effect on the rate of reductive elimination, extension forces increase the rate of reductive elimination by a factor of three over a ~230 pN range of restoring forces relative to the strain-free MeOBiphep complex. Furthermore, the rate response of reductive elimination from nickel(II) bis(trifluorophenyl) complexes as a function of extension force is similar to the previously reported 2.8-fold increase in the rate of reductive elimination from platinum diaryl complexes (P–P)Pt(4-C 6 H 4 NMe 2 ) 2 over the same range of forces

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Structure of active methyl-CoM reductase, Earth’s main methane producer

Summary Our work reveals the structure of the active state of Methyl-Coenzyme M Reductase (MCR), the key and rate-limiting enzyme in biological methane formation. We find large differences between the active Ni(I) and inactive Ni(II) proteins and provide insight into how nature makes and breaks the C-H bond of methane. The Ni(II)-F430 center in inactive MCR contains four planar nitrogen ligands, a lower axial glutamine oxo, and an upper axial thiolate. The Ni(I)-enzyme replaces the axial ligands with a single water. The one-electron redox change results in movement of the Ni ion and upward swing of the β-lactam ring in the tetrapyrrole coupled to a domino-like protein quake through second sphere residues, inter-subunit interactions, a substrate tunnel, affecting even the dimensions of the unit cell. These structural changes lead Ni(I)-MCR to release a charge clamp that, in the Ni(II) state, locks down substrate Coenzyme B. Determining the Ni(I)-MCR structure required development of rigorous anaerobic crystallographic techniques. Validation of the MCR redox state was accomplished by in-line and parallel spectroscopic and unit cell analyses. This structure has large implications for developing technologies to limit methane emissions and efficiently produce biofuels. Methodology described here will enhance structural biology for other oxygen-sensitive enzymes.

09 BIOMASS FUELS↗
DOE OSTI2023

Probing quasar viewing angle with the variability structure function

Given the anisotropic emission from quasar accretion discs, their viewing angle affects estimates of the quasar luminosity, black hole mass, and Eddington ratio. Discs appear overluminous when viewed pole-on and underluminous when viewed at high inclination. In radio-quiet quasars, the viewing angle is usually unknown, although spectroscopic indicators have been proposed. Here, we use a recently discovered universality in the variability structure function (SF) of quasar light curves (LCs), where all quasars show the same SF when clocks run in units of orbital time-scale. As an offset from the mean relation can be caused by incorrect orbital time-scales and thus incorrect luminosities, we correlate these offsets with suggested inclination indicators. We derive SFs from NASA/Asteroid Terrestrial-impact Last Alert System (ATLAS) LCs spanning ~6 yr of observation, using a sample of 183 luminous quasars with measured H β lines as well as 753 quasars with C $\tiny{IV}$ and Mg $\tiny{II}$ lines. Starting from the proposed orientation indicators, we expect quasars with narrower H β lines and with more blueshifted C $\tiny{IV}$ lines to be viewed more pole-on and thus appear overluminous. In contrast, our SF analysis finds that presumed pole-on discs appear underluminous, consistently for both line indicators. We discuss possible explanations for the behaviour of quasars with highly blueshifted C $\tiny{IV}$ lines irrespective of inclination angle, including dusty outflows that might render the accretion disc underluminous and flatter disc temperature profiles with longer orbital time-scales than in thin-disc models but reach no satisfying conclusion.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2020

Distributed fiber sensing systems for 3D combustion temperature field monitoring in coal-fired boilers using optically generated acoustic waves (Final Report)

In this project, we have developed and tested three kinds of fiber optic sensing systems for real time monitoring of temperature variations within an industrial scale boiler furnace. The fiber optic sensing systems target spatial and temporal distributions of high temperature profiles in a boiler furnace in fossil power plants. The reconstructed temperature profile will provide critical input for the control mechanisms to optimize the combustion process. This temperature profile will address the essential problem for fossil power plants in achieving higher efficiency and fewer pollutant emissions. Acoustic pyrometer systems have been used to reconstruct temperature field of power plant boilers based on measuring TOF (times-of-flight) of sound waves along some straight paths in a 2D cross-section of the boiler. In this project, optically generated acoustic signals from a fiber optic sensing system have replaced the acoustic signals generated from an electrical transducer. A 3D reconstruction algorithm replaced the previous 2D model. In this project, three kinds of fiber optic sensing systems have been developed and tested. They are fiber optic sensing system I, fiber optic sensing system II (Distributed Sensing System I) and fiber optic sensing system III (Distributed Sensing System II). For fiber optic sensing system I, the fiber optic ultrasound generator acts as a signal generator. A microphone, hydrophone or other electronic devices serve as a signal receiver. In this system, there are one generator and one receiver. Distance test, water temperature test, air temperature test, air temperature reconstruction, and GE ISBF pilot test were performed by Fiber optic sensing system I. The fiber optic sensing system I successfully detected temperature in all these tests. We got 2D temperature reconstruction results by using the fiber optic sensing system I and it matched the reference data. The fiber optic sensing system I successfully survived in GE ISBF boiler environment (480 °F). For fiber optic sensing system II (Distributed Sensing System I), it is an all optical ultrasound system. The fiber optic ultrasound generator acts as a signal generator. Fiber Bragg Grating (FBG) and Fabry-Perot (FP) sensor act as a signal receiver. In this system, there is one generator and one receiver. Aluminum plate temperature test, furnace high temperature test, and GE ISBF pilot test were performed by the fiber optic sensing system II. Fiber optic sensing system II successfully detected the temperature in all these tests. The fiber optic sensing system II successfully survived at up to 700 °C furnace environment and 320 °C GE ISBF boiler environment. For fiber optic sensing system III (Distributed Sensing System II), it is also an all optical ultrasound system. The fiber optic ultrasound generator acts as a signal generator. Multiple FP fiber sensors act as signal receivers. In this system, there is one generator and three receivers. Three GE ISBF pilot tests were performed by fiber optic sensing system III. The fiber optic sensing system III survived in the cold flow tests in GE’s ISBF pilot test facility. However, we didn’t get high temperature data by using this system since the nanosecond laser issues. During the period of the project, test trials, data simulation and algorithm optimization was performed successfully. For real time temperature field construction, the sampling rate must be fast enough to capture the field variations. The technology of Code-division multiple access (CDMA) is well studied which could allow parallel multiplexing, even if signals overlap in time or frequencies. Moreover, it has been known that extending the length of signal significantly improves SNR. For acoustic signals, these multiplexing techniques have also been widely used, mainly for sonar and acoustic communications. The CDMA modulation technique has been proposed and studied to guarantee high network throughput, low channel access delay and low energy consumption. We have studied the temperature field reconstruction using Gaussian Radial Basis Functions (GRBF)-based approximation approach. Reconstruction of 3D temperature field using Neural Networks with measured TOF and known propagation paths is feasible. 2D and 3D temperature field reconstruction simulation results are achieved. The milestone status is shown in Table 1. We finished milestone 1-8 and milestone 10. For milestone 9, we did three pilot tests by using the fiber optic sensing system III (Distributed Sensing System II) at GE Power. However, due to the failure of the ns laser, we did not get the temperature results. We conducted some additional tasks that were not originally proposed: 1) We fabricated a fiber optic sensing system I and did a pilot test based on this system. 2) In the proposal, we proposed two pilot tests at GE Power. In reality, we finished at least seven pilot tests at GE Power. GE Power has made a lot of efforts for supporting the pilot tests. 3) We got a simulation results based on CDMA. In summary, most of the tasks have been accomplished. The outcome of this project removed a few barriers that hinder the achievement of the final product of the distributed sensing systems. With the successful accomplishment of this project, a prototype of the fiber optic sensing system can be fabricated to attract more interests from companies and other funding agencies.

47 OTHER INSTRUMENTATION↗
DOE OSTI2023

Pd(II) and Rh(I) Catalytic Precursors for Arene Alkenylation: Comparative Evaluation of Reactivity and Mechanism Based on Experimental and Computational Studies

We combine experimental and computational investigations to compare and understand catalytic arene alkenylation using the Pd(II) and Rh(I) precursors Pd(OAc) 2 and [(η 2 -C 2 H 4 ) 2 Rh(µ-OAc)] 2 with arene, olefin and Cu(II) carboxylate at elevated temperature (> 120 °C). Under specific conditions, previous computational and experimental efforts have identified heterotrimetallic cyclic PdCu 2 (η 2 -C 2 H 4 ) 3 (μ-OPiv) 6 and [(η 2 -C 2 H 4 ) 2 Rh(µ-OPiv) 2 ] 2 (µ-Cu) (OPiv = pivalate) species as likely active catalysts for these processes. Further studies of catalyst speciation suggest a complicated equilibrium between Cu(II)-containing complexes containing one Rh or Pd atom with complexes containing two Rh or Pd atoms. At 120 °C, Rh catalysis produces styrene > 20-fold more rapidly than Pd. Also, at 120 °C, Rh is ~98% selective for styrene formation while Pd is ~82% selective. Furthermore, our studies indicate that Pd catalysis has a higher predilection toward olefin functionalization to form undesired vinyl ester, while Rh catalysis is more selective for arene/olefin coupling. However, at elevated temperatures, Pd converts vinyl ester and arene to vinyl arene, which is proposed to occur through low valent Pd(0) clusters that are formed in situ. Regardless of arene functionality, the regioselectivity for alkenylation of mono-substituted arenes with the Rh catalyst gives an approximate 2:1 meta:para ratio with minimal ortho C–H activation. In contrast, Pd selectivity is significantly influenced by arene electronics with electron-rich arenes giving an approximate 1:2:2 ortho:meta:para ratio while the electron deficient (α,α,α)-trifluorotoluene gives a 3:1 meta:para ratio with minimal ortho functionalization. Kinetic intermolecular arene ethenylation competition experiments find that Rh reacts most rapidly with benzene, and the rate of mono-substituted arene alkenylation does not correlate with arene electronics. In contrast, with Pd catalysis, electron-rich arenes react more rapidly than benzene while electron-deficient arenes react less rapidly than benzene. These experimental findings, in combination with computational results, are consistent with the arene C–H activation step for Pd catalysis involving significant η 1 -arenium character due to Pd-mediated electrophilic aromatic substitution character. In contrast, the mechanism for Rh catalysis is not sensitive to arene substituent electronics, which we propose indicates less electrophilic aromatic substitution character for the Rh-mediated arene C–H activation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Spectroscopic observations of progenitor activity 100 days before a Type Ibn supernova

Obtaining spectroscopic observations of the progenitors of core-collapse supernovae is often unfeasible, due to an inherent lack of knowledge as to what stars experience supernovae and when they will explode. In this Letter we present photometric and spectroscopic observations of the progenitor activity of SN 2023fyq before the He-rich progenitor explodes as a Type Ibn supernova. The progenitor of SN 2023fyq shows an exponential rise in flux prior to core collapse. Complex He I emission line features are observed in the progenitor spectra, with a P Cygni-like profile, as well as an evolving broad base with velocities of the order of 10 000 km s −1 . The luminosity and evolution of SN 2023fyq is consistent with a Type Ibn, reaching a peak r -band magnitude of −18.8 mag, although there is some uncertainty regarding the distance to the host, NGC 4388, which is located in the Virgo cluster. We present additional evidence of asymmetric He-rich material being present both prior to and after the explosion of SN 2023fyq, which suggests that this material survived the ejecta interaction. Broad [O I ], C I , and the Ca II triplet lines are observed at late phases, confirming that SN 2023fyq was a genuine supernova, rather than a non-terminal interacting transient. SN 2023fyq provides insight into the final moments of a massive star’s life, demonstrating that the progenitor is likely highly unstable before core collapse.

Brennan, S. J. (ORCID:0000000313256235)↗
DOE OSTI2025

Electrochemical stability and corrosion behavior of Ni-Cr alloy in molten LiCl-KCl salt

This study investigated the electrochemical properties and potential-dependent stability of Cr(II) and Ni(II) in a eutectic LiCl-KCl molten salt at 500 °C under an argon atmosphere using a three-electrode cell configuration with a glassy carbon working electrode, Ag/Ag + reference electrode, and graphite counter electrode. Cyclic voltammetry was employed to characterize the Cr(0)/Cr(II)/Cr(III) and Ni(0)/Ni(II) redox transitions, yielding diffusion coefficients of 0.50 (±0.01) × 10 −5 cm 2 s −1 for Cr(II) and 0.91 (±0.16) × 10 −5 cm 2 s −1 for Ni(II) at 500 °C. The redox stability domains of these species provided insight into the corrosion mechanisms of a Ni-Cr alloy (80–20 wt %) in LiCl-KCl salt. The measured open circuit potential of the alloy corresponded to the range of potentials where the Ni(0) and Cr(II) species are stable, indicating a preferential dissolution of Cr. Immersion testing of the alloy for 336 h confirmed significant Cr depletion (or Ni-enrichment) at the surface layer, corroborating Cr dealloying as the dominant corrosion reaction under open circuit conditions. Additionally, the application of a small anodic overpotential (0.11 V) resulted in selective Cr dissolution while a large anodic overpotential (0.25 V) resulted in co-dissolution of both Cr and Ni. Furthermore, these results demonstrate that the corrosion mechanisms of a Ni-Cr alloy in LiCl-KCl depend upon the applied potential, and thus the redox conditions of the molten salt should be carefully controlled in the design of a redox buffer to mitigate corrosion in molten salt environments.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Fullerene Promotes CO 2 Reduction to Methanol by a Cobalt(II) Phthalocyanine Electrocatalyst

Heterogenization of molecular electrocatalysts offers an attractive way to improve the catalytic selectivity and efficiency of CO 2 conversion to liquid fuels. Herein, we employ density functional theory to compare the mechanism of CO 2 RR by a cobalt(II) tetra(amino)phthalocyanine (Co(II)Pc(NH 2 ) 4 ) electrocatalyst with and without the presence of fullerene support. Our DFT calculations suggest that the CO 2 reduction mechanism is initiated by a metal-based electron reduction followed by subsequent CO 2 nucleophilic addition, electron transfer, proton transfer, water dissociation, and proton-coupled electron transfer steps that lead to CO and methanol formation. We show that graphitic interactions between the Co(II)Pc(NH 2 ) 4 electrocatalyst and C 60 support selectively improve the CO 2 RR to methanol at mild potentials. The undesirable hydrogen evolution reaction (HER) was also investigated for both electrocatalysts and proceeds via the protonation of the cobalt metal center over the nitrogen atom in the inner ring. The competition between the HER and the CO 2 RR was improved in favor of CO and methanol formation using the Co(II)Pc(NH 2 ) 4 @C 60 electrocatalyst. Overall, our results suggest C 60 as a promising graphitic support for molecular electrocatalysts integration for CO 2 catalysis.

Alcohols↗
DOE OSTI2025

Measurement of the time-integrated 𝐶⁢𝑃 asymmetry in 𝐷 0 → 𝐾$^{0}_{S}$𝐾$^{0}_{S}$ decays using opposite-side flavor tagging at Belle and Belle II

We measure the time-integrated 𝐶⁢𝑃 asymmetry in 𝐷 0 → 𝐾$^{0}_{S}$𝐾$^{0}_{S}$ decays reconstructed in 𝑒 + ⁢𝑒 − → $c\bar{c}$ events collected by the Belle and Belle II experiments. The corresponding data samples have integrated luminosities of 980 and 428 fb −1 , respectively. To infer the flavor of the 𝐷 0 meson, we exploit the correlation between the flavor of the reconstructed decay and the electric charges of particles reconstructed in the rest of the 𝑒 + ⁢𝑒 − → $c\bar{c}$ event. This results in a sample which is independent from any other previously used at Belle or Belle II. The result, 𝐴 𝐶⁢𝑃 ⁡(𝐷 0 → 𝐾$^{0}_{S}$𝐾$^{0}_{S}$)=(1.3±2.0±0.2)%, where the first uncertainty is statistical and the second systematic, is consistent with previous determinations and with 𝐶⁢𝑃 symmetry.

CP violation↗
DOE OSTI2021

Calcium-Ion Binding Mediates the Reversible Interconversion of Cis and Trans Peroxido Dicopper Cores

Coupled dinuclear copper oxygen cores (Cu 2 O 2 ) featured in type III copper proteins (hemocyanin, tyrosinase, catechol oxidase) are vital for O 2 transport and substrate oxidation in many organisms. μ-1,2-cis peroxido dicopper cores ( C P) have been proposed as key structures in the early stages of O 2 binding in these proteins; their reversible isomerization to other Cu 2 O 2 cores are directly relevant to enzyme function. Furthermore, despite the relevance of such species to type III copper proteins and the broader interest in the properties and reactivity of bimetallic C P cores in biological and synthetic systems, the properties and reactivity of C P Cu 2 O 2 species remain largely unexplored. Herein, we report the reversible interconversion of μ-1,2-trans peroxido ( T P) and C P dicopper cores. Ca II mediates this process by reversible binding at the Cu 2 O 2 core, highlighting the unique capability for metal-ion binding events to stabilize novel reactive fragments and control O 2 activation in biomimetic systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Calcium‐Ion Binding Mediates the Reversible Interconversion of Cis and Trans Peroxido Dicopper Cores

Abstract Coupled dinuclear copper oxygen cores (Cu 2 O 2 ) featured in type III copper proteins (hemocyanin, tyrosinase, catechol oxidase) are vital for O 2 transport and substrate oxidation in many organisms. μ ‐1,2‐ cis peroxido dicopper cores ( C P ) have been proposed as key structures in the early stages of O 2 binding in these proteins; their reversible isomerization to other Cu 2 O 2 cores are directly relevant to enzyme function. Despite the relevance of such species to type III copper proteins and the broader interest in the properties and reactivity of bimetallic C P cores in biological and synthetic systems, the properties and reactivity of C P Cu 2 O 2 species remain largely unexplored. Herein, we report the reversible interconversion of μ ‐1,2‐ trans peroxido ( T P ) and C P dicopper cores. Ca II mediates this process by reversible binding at the Cu 2 O 2 core, highlighting the unique capability for metal‐ion binding events to stabilize novel reactive fragments and control O 2 activation in biomimetic systems.

Vargo, Natasha P.↗
DOE OSTI2022

Photocatalytic Hydrogen Evolution by a De Novo Designed Metalloprotein that Undergoes Ni–Mediated Oligomerization Shift

De novo metalloprotein design involves the construction of proteins guided by specific repeat patterns of polar and apolar residues, which, upon self-assembly, provide a suitable environment to bind metals and produce artificial metalloenzymes. While a wide range of functionalities have been realized in de novo designed metalloproteins, the functional repertoire of such constructs towards alternative energy-relevant catalysis is currently limited. Here we show the application of de novo approach to design a functional H 2 evolving protein. The design involved the assembly of an amphiphilic peptide featuring cysteines at tandem a/d sites of each helix. Intriguingly, upon Ni II addition, the oligomers shift from a major trimeric assembly to a mix of dimers and trimers. The metalloprotein produced H 2 photocatalytically with a bell-shape pH dependence, having a maximum activity at pH 5.5. Transient absorption spectroscopy is used to determine the timescales of electron transfer as a function of pH. Selective outer sphere mutations are made to probe how the local environment tunes activity. Finally, a preferential enhancement of activity is observed via steric modulation above the Ni II site, towards the N-termini, compared to below the Ni II site towards the C-termini.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗