Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Heat Flux”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Effect of gage size on the measurement of local heat flux

General formulas are derived for determining gage averaging errors of strip-type heat flux meters used in the measurement of one-dimensional heat flux distributions. In addition, a correction procedure is presented which allows a better estimate for the true value of the local heat flux. As an example of the technique, the formulas are applied to the cases of heat transfer to air slot jets impinging on flat and concave surfaces. It is shown that for many practical problems, the use of very small heat flux gages is often unnecessary.

Baumeister, K. J.↗
NASA NTRS1973

Extended hydrodynamic theory of the peak and minimum pool boiling heat fluxes

The hydrodynamic theory of the extreme pool boiling heat fluxes is expanded to embrace a variety of problems that have not previously been analyzed. These problems include the prediction of the peak heat flux on a variety of finite heaters, the influence of viscosity on the Taylor and Helmoltz instability mechanisms with application to film boiling and to the peak heat flux in viscous liquids, the formalization of the analogy between high-current-density electrolysis and boiling, and the description of boiling in the low-gravity limit. The predictions are verified with a large number of new data.

Linehard, J. H.↗
NASA NTRS1992

Novel thin-film heat flux sensors

A new and simpler design for thin-film heat flux sensors for utilization in high heat flux environments is presented. The design of these sensors consists of a planar differential thermopile made up of a number of thermocouple pairs arranged in a circular array, two different thermal resistance layers deposited on the inside and outside junctions of the thermopile and a high emissivity coating. This design has shown good potential for measuring heat fluxes in severe environments of aerospace propulsion systems.

Bhatt, Hemanshu↗
NASA NTRS1997

Surface Energy Heat Fluxes Using Remotely Sensed Parameters

Realistic estimates of surface energy heat fluxes are needed for the study of water and energy interactions between the land and atmosphere. The primary objective of this work is to study the estimation of surface heat energy fluxes using remote sensing derived parameters under different spatial and temporal conditions. Surface energy fluxes and remote sensing derived data from two sources were analyzed. First, we used surface heat flux, remote sensing, and ancillary data from the International Satellite Land Surface Climatology Project (ISLSCP), mapped at a 1 deg. x 1 deg. grid. Second, we used NOAA AVHRR (1 km), weather station, and ancillary data to derive estimates of surface latent and sensible heat energy fluxes over a 100 sq kilometers area for three test sites: 1) First ISLSCP Field Experiment (FIFE) grassland site, Konza Prairie, Kansas; 2) Howland, Maine Forest Ecosystem Dynamics Site; and 3) Walnut Gulch, scrubland site, surrounding Tombstone, Arizona. Satellite derived estimates of land surface temperature, surface albedo, and spectral vegetation index are used in selected models to provide estimates of surface heat fluxes. Analysis of results from the 1 deg. x 1 deg. grid for North America indicated there were similar, overall correlations between sensible and latent heat energy fluxes versus remotely sensed vegetation index and ground temperature during dry and wet year conditions. However, there were significant differences in correlations between years when stratified by land cover class. Analysis of 100 km x 100 km data (1 km resolution) indicated partitioning the areas in to primary versus secondary cover, with the secondary cover comprising less than 5% of the area, significantly improved surface heat energy flux estimates.

Toll, David L.↗
NASA NTRSDate not supplied

The Electron Heat Fluxes Associated with Electron Precipitation in the Region of Diffuse Aurora

Electron heat flux that comes from the magnetosphere to the upper ionospheric altitudes controls the value of electron temperature in the core plasma, and, as a result, the total electron density content that is required for different kinds of space weather applications. Knowing the thermal electron heat flux at the upper ionospheric boundaries is the Achilles' heel of all ionospheric models. Such a thermal heat flux setting is especially difficult to justify in the region of the diffuse aurora that is connected to a large energy reservoir of electrons with energies of a few kiloelectron volts, the Earth's plasma sheet, where magnetosphere-ionosphere coupling processes are strongly interconnected. We use the simulated heat flux provided by SuperThermal Electron Transport (STET) code to estimate electron temperatures at the upper ionospheric altitudes and compare these results with corresponding observations from the Defense Meteorological Satellite Program satellite during Saint Patrick's Days 2013 and 2015 Geomagnetic Storms.

George V. Khazanov↗
NASA NTRS1992

High heat flux measurements and experimental calibrations/characterizations

Recent progress in techniques employed in the measurement of very high heat-transfer rates in reentry-type facilities at the Arnold Engineering Development Center (AEDC) is described. These advances include thermal analyses applied to transducer concepts used to make these measurements; improved heat-flux sensor fabrication methods, equipment, and procedures for determining the experimental time response of individual sensors; performance of absolute heat-flux calibrations at levels above 2,000 Btu/cu ft-sec (2.27 kW/cu cm); and innovative methods of performing in-situ run-to-run characterizations of heat-flux probes installed in the test facility. Graphical illustrations of the results of extensive thermal analyses of the null-point calorimeter and coaxial surface thermocouple concepts with application to measurements in aerothermal test environments are presented. Results of time response experiments and absolute calibrations of null-point calorimeters and coaxial thermocouples performed in the laboratory at intermediate to high heat-flux levels are shown. Typical AEDC high-enthalpy arc heater heat-flux data recently obtained with a Calspan-fabricated null-point probe model are included.

Kidd, Carl T.↗
DOE OSTI2022

Measurements of multiple heat flux components at the divertor target by using surface eroding thermocouples (invited)

The Surface Eroding Thermocouple (SETC) is a robust diagnostic utilized in DIII-D to provide fast, edge-localized modes (ELMs) resolved heat flux measurements, in particular in geometric regions that are too shadowed for traditional infrared thermography. In order to further investigate the power dissipation in the divertor region, a combination of flush-mounted and recessed SETCs was developed to assess the effect on surface heating from non-charged particles at the divertor target. Utilizing the Divertor Materials Evaluation System sample exposure platform, the first demonstration of the feasibility of using this new method to distinguish between the heat flux from charged particles and that from neutrals and radiative heating was achieved. This paper details the process of using the combination of flush SETCs and recessed SETCs to measure the multiple heat flux components at the divertor target and further discusses how to determine two important ratios, α (ratio of heat flux from charged particles deposit on recessed SETC to that deposit on flush SETC) and β (ratio of heat flux from non-charged particles deposit on recessed SETC to that deposit on flush SETC), in the estimation of the heat flux from non-charged particle sources. Using a time dependent ratio α, it was found that ~50% of the total incident heat flux is attributable to the non-charged particles in the fully detached open divertor in DIII-D. Finally, the new application of similar SETC diagnostics in the Small Angle Slot divertor with a V-like configuration and partial tungsten coated surface (SAS-VW) is also introduced.

47 OTHER INSTRUMENTATION↗
NASA NTRS1984

High temperature thermocouple and heat flux gauge using a unique thin film-hardware hot juncture

A special thin film-hardware material thermocouple (TC) and heat flux gauge concept for a reasonably high temperature and high flux flat plate heat transfer experiment was fabricated and tested to gauge temperatures of 911 K. This concept was developed for minimal disturbance of boundary layer temperature and flow over the plates and minimal disturbance of heat flux through the plates. Comparison of special heat flux gauge Stanton number output at steady-state conditions with benchmark literature data was good and agreement was within a calculated uncertainty of the measurement system. Also, good agreement of special TC and standard TC outputs was obtained and the results are encouraging. Oxidation of thin film thermoelements was a primary failure mode after about 5 of operation.

Liebert, C. H.↗
NASA NTRS1985

High-temperature thermocouple and heat flux gauge using a unique thin film-hardware hot junction

A special thin film-hardware material thermocouple (TC) and heat flux gauge concept for a reasonably high temperature and high flux flat plate heat transfer experiment was fabricated and tested to gauge temperatures of 911 K. This concept was developed for minimal disturbance of boundary layer temperature and flow over the plates and minimal disturbance of heat flux through the plates. Comparison of special heat flux gauge Stanton number output at steady-state conditions with benchmark literature data was good and agreement was within a calculated uncertainty of the measurement system. Also, good agreement of special TC and standard TC outputs was obtained and the results are encouraging. Oxidation of thin film thermoelements was a primary failure mode after about 5 of operation.

Liebert, C. H.↗
NASA NTRS1984

Development of heat flux sensors in turbine airfoils

The objective is to develop heat flux sensors suitable for use on turbine airfoils and to verify the operation of the heat flux measurement techniques through laboratory experiments. The requirements for a program to investigate the measurement of heat flux on airfoils in areas of strong non-one-dimensional flow were also identified.

Atkinson, W. H.↗
NASA NTRS1992

Satellite-derived surface latent heat fluxes in a rapidly intensifying marine cyclone

Surface latent heat fluxes are estimated in the vicinity of a rapidly deepening cyclone before and during its period of most rapid intensification. This was done with a bulk parameterization scheme and remotely sensed input data. A method is studied for estimating the difference in specific humidity between the surface and a ten meter height using the Special Sensor Microwave/Imager (SSM/I) observed integrated water vapor field and a sea surface temperature analysis. The surface latent heat flux fields generally have estimated errors below 40 pct. south of 40 deg. N and outside the region of high integrated water vapor values associated with frontal bands. The method of estimating surface latent heat fluxes for the case study was found to be usable in most regions of the Northwest Atlantic Ocean except for those locations directly adjacent to coastlines in instances of offshore flow and in the vicinity of surface fronts.

Miller, Douglas K.↗
NASA NTRS1989

A study of oceanic surface heat fluxes in the Greenland, Norwegian, and Barents Seas

This study examines oceanic surface heat fluxes in the Norwegian, Greenland, and Barents seas using the gridded Navy Fleet Numerical Oceanography Central surface analysis and the First GARP Global Experiment (FGGE) IIc cloudiness data bases. Monthly and annual means of net and turbulent heat fluxes are computed for the FGGE year 1979. The FGGE IIb data base consisting of individual observations provides particularly good data coverage in this region for a comparison with the gridded Navy winds and air temperatures. The standard errors of estimate between the Navy and FGGE IIb winds and air temperatures are 3.6 m/s and 2.5 C, respectively. The computations for the latent and sensible heat fluxes are based on bulk formulas with the same constant heat exchange coefficient of 0.0015. The results show extremely strong wintertime heat fluxes in the northern Greenland Sea and especially in the Barents Sea in contrast to previous studies.

Hakkinen, Sirpa↗
NASA NTRS1996

An Investigation of the Compatibility of Radiation and Convection Heat Flux Measurements

A method for determining time-resolved absorbed surface heat flux and surface temperature in radiation and convection environments is described. The method is useful for verification of aerodynamic, heat transfer and durability models. A practical heat flux gage fabrication procedure and a simple one-dimensional inverse heat conduction model and calculation procedure are incorporated in this method. The model provides an estimate of the temperature and heat flux gradient in the direction of heat transfer through the gage. This paper discusses several successful time-resolved tests of this method in hostile convective heating and cooling environments.

Liebert, Curt H.↗
DOE OSTI2023

Measurements and modeling of type-I and type-II ELMs heat flux to the DIII-D divertor

Type-I and type-II edge-localized-modes (ELMs) heat flux profiles measured at the DIII-D divertor feature a peak in the vicinity of the strike-point and a plateau in the scrape-off-layer (SOL), which extends to the first wall. The plateau is present in attached and detached divertors and it is found to originate with plasma bursts upstream in the SOL. The integrated ELM heat flux is distributed at ~65% in the peak and ~35% in this plateau. The parallel loss model, currently used at ITER to predict power loads to the walls, is benchmarked using these results in the primary and secondary divertors with unprecedented constraints using experimental input data for ELM size, radial velocity, energy, electron temperature and density, heat flux footprints and number of filaments. The model can reproduce the experimental near-SOL peak within ~20%, but cannot match the SOL plateau. Employing a two-component approach for the ELM radial velocity, as guided by intermittent data, the full radial heat flux profile can be well matched. The ELM-averaged radial velocity at the separatrix, which explains profile widening, increases from ~0.2 km s –1 in attached to ~0.8 km s –1 in detached scenarios, as the ELM filaments' path becomes electrically disconnected from the sheath at the target. The results presented here indicate filaments fragmentation as a possible mechanism for ELM transport to the far-SOL and provide evidence on the beneficial role of detachment to mitigate ELM flux in the divertor far-SOL. However, these findings imply that wall regions far from the strike points in future machines should be designed to withstand significant heat flux, even for small-ELM regimes.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Global impacts of vegetation clumping on regulating land surface heat fluxes

The clumping index (CI) quantifies the non-random distribution of vegetation across space, which regulates the canopy radiative transfer processes and land surface carbon, water, and energy cycles. However, its impact on global surface energy budget, particularly sensible heat fluxes and surface temperature, is not well understood. Additionally, while there have been studies showing significant seasonal variations in CI, the impacts of these variations on surface energy fluxes remain unclear. In this study, we incorporated satellite-derived spatially and temporally explicit CI data into the Community Land Model version 5 (CLM5) to evaluate the effects of CI on global land energy fluxes. Our results showed that including CI increased the global mean sensible heat flux dissipated from ground by 3.9 W m -2 (~18%), while decreasing the global mean vegetation sensible heat flux by 4.9 W m -2 (~65%), resulting in a total sensible heat decrease of 1.0 W m -2 (~3%). In contrast, CI increased the global mean latent heat flux by 0.8 W m -2 (~2%), primarily due to increased evapotranspiration (up to 11 W m -2 ) in tropical regions. We also found considerable impacts of seasonal variations in CI, particularly on sensible heat fluxes from ground and vegetation in evergreen needleleaf forests and deciduous needleleaf forests. Using constant CI rather than considering seasonal variations resulted in significant overestimation and underestimation of the sensible heat fluxes from vegetation and ground, respectively, in boreal summer. In conclusion, these changes in surface energy fluxes caused by CI and its seasonal variations led to up to 1.7 and 0.5 K differences in simulated mean ground temperature. These findings highlight the importance of including CI and considering its seasonal variations in modeling land surface energy fluxes.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1976

Evidence for the regulation of solar wind heat flux at 1 AU

Observational evidence favoring the local regulation of solar-wind heat flux at 1 AU is reviewed, and four months of IMP 6 plasma and magnetic-field data are merged and analyzed in order to investigate what might be regulating the heat flux. A statistical analysis of the data shows that the solar-wind Alfven speed is probably regulating the heat flux locally at 1 AU and that the Alfven speed, the velocity difference between the peak of low-energy electrons and the bulk plasma velocity, and the solar-wind velocity component projected along the local spiral angle are statistically well correlated for Alfven speeds not exceeding about 70 km/s. A time-series analysis of the data indicates that only the Alfven speed and the velocity difference between the peak of low-energy electrons and the bulk plasma velocity are well correlated both qualitatively and quantitatively on a microscopic time scale. It is strongly suggested that, at times, the solar-wind heat flux is locally regulated by the magnitude of the Alfven speed at 1 AU. Uncertainties in the results are discussed.

Feldman, W. C.↗
NASA NTRS1964

Orbiter heat flux computer program

A two-phased contract is currently underway to develop 1) a set of parametric curves of absorbed heat flux for specific geometries, and 2) a generalized computer program whose output is absorbed heat flux on the surfaces of a planet orbiting spacecraft. The absorbed heat fluxes include the effects of blockage by and reflections from adjacent spacecraft surfaces, assuming all surfaces to be diffuse. The final computer program will calculate fluxes on any of ten arbitrarily positioned plane surfaces, with any surface properties, planetary radiation characteristics, solar intensity, and orbital parameters. Outputs will be heat fluxes versus time, geometrical configuration factors, and radiant flux interchange factors.

COMPUTER PROGRAM↗