Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “HOT PRESSING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

Strength of hot isostatically pressed and sintered reaction bonded silicon nitrides containing Y2O3

The hot isostatic pressing of reaction bonded Si3N4 containing Y2O3 produced specimens with greater room temperature strengths than those by high pressure nitrogen sintering of the same material. Average room temperature bend strengths for hot isostatically pressed reaction bonded silicon nitride and high pressure nitrogen sintered reaction bonded silicon nitride were 767 and 670 MPa, respectively. Values of 472 and 495 MPa were observed at 1370 C. For specimens of similar but lower Y2O3 content produced from Si3N4 powder using the same high pressure nitrogen sintering conditions, the room temperature strength was 664 MPa and the 1370 C strength was 402 MPa. The greater strengths of the reaction bonded silicon nitride materials in comparison to the sintered silicon nitride powder material are attributed to the combined effect of processing method and higher Y2O3 content.

William A Sanders↗

Hot Isostatic Pressing of Radioactive Nuclear Waste: The Calcine at INL - 16348

Hot Isostatic Pressing (HIP) is a technology that has been around for 60+ years. By using high temperature and high gas pressure, dry metal and ceramic powders can be consolidated and a volume decrease can be achieved. This paper presents the efforts using the HIPing process at the Idaho National Laboratory to treat the calcine radioactive waste. Once loaded into collapsible canisters, the HIPing would be used to treat the waste before final disposal. The resulting volume reduction was shown to be 20-70% and the cost ratio vs vitrification is 1:1.74. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Development of Hot-Isostatic Pressing for Treatment of UK ILW Radioactive Wastes - 18280

Hot-Isostatic Pressing (HIPing) has been proposed as an improved method for the treatment of radioactive wastes in the UK. Sludges and slurries housed on the Sellafield site are a prime candidate for HIP treatment due to their large volumes and issues associated with the use of the baseline cementation strategy. Options have been developed by GeoRoc Ltd to co-process these wastes, including a detailed conceptual plant design. This paper will describe research and development aimed at demonstrating the viability of the concept presented in this design. This paper summarizes two studies performed to address the knowledge gaps identified for treatment of these wastes using HIP technology. The first study related to the poorly characterized nature of the wastes, which requires any treatment option to be flexible in terms of the chemical and physical properties of the waste feed. The second study involved demonstrating that HIPing can be effectively utilized at a scale applicable to treat a waste inventory estimated to be in excess of 5,000 m{sup 3}. The first section of this paper presents a summary of research carried out to determine where variation in the waste stream composition may affect the processing and wasteform produced when HIPing Magnox sludges. This study aimed to qualify where restrictions on the process envelope may exist due to poorly defined waste-stream characteristics. A baseline wasteform was selected with the aim of achieving significant waste volume reduction, while producing a physically and chemically stable wasteform. A glass-bonded magnesium-titanate/magnesium-silicate wasteform was selected as the preferred option for the Magnox sludge wastes. A series of studies investigated the densification and phase formation of waste-forms by altering key variables in the Magnox sludge simulant. To test the extremes of the processable waste loading, samples were produced and characterized at 100 wt% waste-loading for Magnox sludge, Site-Ion Exchange Plant (SIXEP) sand/clinoptilolite and a 50:50 mix of the two waste-streams. Further studies involved a) altering the waste loading to additive mass ratio (to simulate changes in the waste loading/sludge solids content), b) varying the particle size distribution from the datum to include only small or large particulates in the sludge feed; and c) introducing up to 20 wt% metallic Magnox alloy, organic species or carbonate materials (to determine how their inclusion may affect the processing and densification of the materials). A U{sub 3}O{sub 8} loaded sample was also produced using the baseline Magnox sludge formulation. All the tests performed were shown to produce monolithic, well densified waste-forms with substantial volume reductions. Minimal variations from the baseline were noted but the waste-forms produced with these deviations was determined to be of comparable quality to of the baseline product. U{sub 3}O{sub 8} was shown to behave in a similar fashion to the ZrO{sub 2} surrogate used to simulate it in the process envelope studies and was encapsulated in the magnesium titanate/magnesium silicate matrix. This work demonstrates that HIP technology can successfully produce waste-forms across the broad process envelope expected in the Magnox sludge inventory. It is also possible to produce monolithic waste-forms at 100 wt% waste loading from Magnox sludges, SIXEP sand clinoptilolite slurries or a co-processed mixture of the two. The second part of this paper summarizes a commercially relevant demonstration of HIP technology for the treatment of sludge and slurry wastes housed at the Sellafield site (UK). This study culminated in production of the largest HIPed wasteform successfully produced to date. This study was performed in a series of stages. Investigations into formulation and properties of waste-forms were performed at a lab scale to evaluate suitable wasteform systems and identify suitable combinations of additives and waste loadings. Scale up demonstrations were then performed in stages with custom-designed HIP canisters. Scale-up and characterization of key wasteform properties were successfully performed with initial canister volumes of 50 ml, 400 ml and 8 L. Suitable front-end unit operations to produce a granular, free-flowing calcined simulant were demonstrated at an engineering scale. The demonstration was successful in processing a HIP canister with an initial starting volume in excess of 100 L. A 75 % volume reduction from the raw sludge was achieved at scale while demonstrating that HIP is applicable at suitably large scale for immobilization of ILW waste. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Processing and consolidation of copper/tungsten

Here, we developed a copper/tungsten (Cu/W) composite for mesoscale Materials Science applications using the novel High-Energy Diffraction Microscopy (HEDM) technique. Argon-atomized copper powder was selected as the starting raw powder and screened to remove the extremely large particle fraction. Tungsten particles were collected by milling and screening the -325 mesh tungsten powder between 500 and 635 mesh sieves. Hot pressing of screened Cu powder was performed at 900 °C in Ar/4 %H 2 atmosphere. XRD and ICP results show that the hot-pressed Cu sample consists of about 5 vol% Cu 2 O, which is caused by the presence of oxygen on the surface of the starting Cu powder. Hot pressing the copper powder in a pure hydrogen atmosphere was successful in removing most of the surface oxygen. Our process was also implemented for hot pressing the Cu/W composite. The density of the Cu/W composites hot pressed at 950 °C in pure hydrogen was about 94 % of the theoretical density (TD). The hot-pressed Cu/W composites were further hot isostatic pressed at 1050 °C in argon atmosphere, which results in 99.6 % of the TD with the designed Cu grain size and W particle distribution. Tensile specimens with D-notch were machined using the wire EDM method. Furthermore, the processing and consolidation of these materials will be discussed in detail. The HEDM images are also showed and discussed.

36 MATERIALS SCIENCE↗

Crystallization behavior and properties of BaO-Al2O3-2SiO2 glass matrices

Glass of stoichiometric celsian composition, BaO-Al2O3-SiO2, has a density of 3.39 g/cu cm, a thermal expansion coefficient of 6.6 x 10 to the -6th/C, a glass-transition temperature of 910 C, and a dilatometric softening point of 925 C. On heat treatment, only hexacelsian crystallized out on the surface, but both celsian and hexacelsian were present in the bulk. Effects of cold isostatic pressing (CIP), sintering, and hot-pressing, in the presence and absence of an additive, on the formation of the celsian phase in the glass have been studied. CIP'd samples, after appropriate heat treatments, always crystallized out as celsian, whereas presence of 5-10 wt pct of an additive was necessary for formation of celsian in sintered as well as hot-pressed specimens. Green density increased with CIP'ing pressure but had no effect on sintered density. Hot-pressing resulted in fully dense samples.

Drummond, Charles H., III↗

Adhesion in thermomechanically processed seaweed-lignocellulosic composite materials

The increasing concerns associated with petroleum-derived polymers motivate the development of sustainable, renewably sourced alternatives. In ubiquitous applications such as structural materials for infrastructure, the built environment as well as packaging, where natural materials such as wood are used, we rely on nonrenewable and nondegradable polymers to serve as adhesives. In wood panels, such as medium density fiberboards (MDFs), formaldehyde-based resins are predominantly used to bond wood fibers and to provide strength to the materials. To further mitigate the environmental impact of construction materials, more sustainable adhesives need to be investigated. Here, in this article, we introduce Ulva seaweed as an adhesive to enable cohesion and strength in hot-pressed wood panels. Upon hot-pressing, powdered Ulva flows in between the wood particles, generating a matrix, which provides strong binding. We show that the flexural strength of Ulva-bonded wood biocomposites increases with increasing Ulva concentrations. At an Ulva concentration of 40 wt%, our composites reach an average elastic modulus of 6.1 GPa, and flexural strength of 38.2 MPa (compared to 4.7 GPa and 22.6 MPa, respectively, for pure wood compressed at the same pressing conditions). To highlight the bonding mechanisms, we performed infrared and x-ray photoelectron spectroscopy and identified indications of fatty acid mobility during hot-pressing. In addition, we demonstrate that the presence of Ulva improves other properties of the composites such as water resistance and fame retardancy. Ulva is also shown to behave as an excellent adhesive agent between two prepressed beams. Finally, we perform an in-depth analysis of the environmental impact of wood-Ulva biocomposites.

36 MATERIALS SCIENCE↗

Production of an impermeable composite of irradiated graphite and glass by hot isostatic pressing as a long term leach resistant waste form

Around 250,000 tons of irradiated graphite (i-graphite) exists worldwide and can be considered as a current waste or future waste stream. The largest national i-graphite inventory is located in UK (∼ 100,000 tons) with significant quantities also in Russia and France [5]. Most of the i-graphite remains in the cores of shutdown nuclear reactors including the MAGNOX type in UK and the UNGG in France. Whilst there are still operational power reactors with graphite cores, such as the Russian RBMKs and the AGRs in UK, all of them will reach their end of life during the next two decades. The most common reference waste management option of i-graphite is a wet or dry retrieval of the graphite blocks from the reactor core and the grouting of these blocks in a container without further conditioning. This produces large waste package volumes because the encapsulation capacity of the grout is limited and large cavities in the graphite blocks could reduce the packing densities. Packing densities from 0.5 to 1 tons per cubic meter have been assumed for grouting solutions. Furthermore the grout is permeable. This could over time allow the penetration of aqueous phases into the waste block and a potential dissolution and release of radionuclides. As a result particularly highly soluble radionuclides may not be retained by the grout. Vitrification could present an alternative, however a similar waste package volume increase may be expected since the encapsulation capacity of glass is potentially similar to or worse than that of grout. FNAG has developed a process for the production of a graphite-glass composite material called Impermeable Graphite Matrix (IGM) [3]. This process is also applicable to irradiated graphite which allows the manufacturing of an impermeable material without volume increase. Crushed i-graphite is mixed with 20 vol.% of glass and then pressed under vacuum at an elevated temperature in an axial hot vacuum press (HVP). The obtained product has zero or negligible porosity and a water impermeable structure. Structural analysis shows that the glass in the composite has replaced the pores in the graphite structure. The typical pore volume of a graphite material is in the range of 20 vol.%. Therefore no volume increase will occur in comparison with the former graphite material. This IGM material will allow the encapsulation of graphite with package densities larger than 1.5 ton per cubic meter. Therefore a huge volume saving can be achieved by such an alternative encapsulation method. Disposal performance is also enhanced since little or no leaching of radionuclides is observed due to the impermeability of the material NNL and FNAG have proved that IGM can be produced by hot isostatic pressing (HIP) which has several advantages for radioactive materials over the HVP process. - The sealed HIP container avoids the release of any radionuclides. - The outside of the waste package is not contaminated. - The HIP process time is shorter than the HVP process time. The isostatic press avoids anisotropic density distributions. - Simple filling of the HIP container has advantages over the filling of an axial die. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Thermal Processing Conditions for the Synthesis of Near Theoretical Density Li 5 La 3 Ta 2 O 12 Ceramics for Ceramic Dual-Mode Detectors

A family of Li-containing garnet compounds, extensively investigated for Li-ion solid electrolyte applications, show great potential to be developed into transparent ceramic dual-mode scintillators. In particular, Li 5 La 3 Ta 2 O 12 (LLTaO) shows promise as an efficient dual-mode scintillator due to its high Li content, high density, non-hygroscopicity, and high effective-Z. Often the synthesis of LLTaO ceramics involves solid state processing techniques starting with oxide and carbonate powders, calcining, sintering for the removal of residual porosity, and post-processing. This study focuses on two objectives: (1) establishing thermal processing boundary conditions for a flexible alkoxide-based sol-gel method for synthesizing fine-grained powders; and (2), consolidating powders via hot-pressing to form high-density ceramics. In this study, near single-phase ceramics were achieved by hot-pressing sol-gel powders with varying amounts of excess Li. Rietveld refinements were used to analyze X-ray diffraction data and provide a quantitative evaluation of the phases present in the hot pressed ceramics. Some of the diffraction data showed large low angle peak asymmetry, suggesting the presence of two cubic Li 5 La 3 Ta 2 O 12 garnet phases with different lattice parameters. Depending on the synthesis and processing conditions, the refinement revealed ~ 90 wt% concentration of a phase with a ≈ 12.8 Å and ~ 10 wt% concentration of a phase with a ≈ 12.9 Å, indicating a remaining excess of Li in the hot pressed ceramics in the large lattice parameter phase. These synthesis experiments allowed for the determination of a baseline for Li loss during hot-pressing. X-ray excited radioluminescence and photoluminescence excitation and emission spectra were obtained from the hot pressed ceramics. In conclusion, the measured emission spectra featured broad tantalate emission and line emissions likely from a rare-earth impurity.

36 MATERIALS SCIENCE↗

Fabrication of Monolithic RERTR Fuels by Hot Isostatic Pressing

The RERTR (Reduced Enrichment for Research and Test Reactors) Program is developing advanced nuclear fuels for high-power test reactors. Monolithic fuel design provides higher uranium loading than that of the traditional dispersion fuel design. Hot isostatic pressing is a promising process for low-cost batch fabrication of monolithic RERTR fuel plates for these high-power reactors. Bonding U Mo fuel foil and 6061 Al cladding by hot isostatic press bonding was successfully developed at Idaho National Laboratory. Due to the relatively high processing temperature, the interaction between fuel meat and aluminum cladding is a concern. Two different methods were employed to mitigate this effect: (1) a diffusion barrier and (2) a doping addition to the interface. Both types of fuel plates have been fabricated by hot isostatic press bonding. Preliminary results show that the direct fuel/cladding interaction during the bonding process was eliminated by introducing a thin zirconium diffusion barrier layer between the fuel and the cladding. Fuel plates were also produced and characterized with a silicon-rich interlayer between fuel and cladding. This paper reports the recent progress of this developmental effort and identifies the areas that need further attention.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Hot Isostatic Pressing of Engineered Forms of I-AgZ

Hot isostatic pressing (HIP) is being considered for direct conversion of 129 I-bearing materials to a radiological waste form. The removal of volatile radioactive 129 I from the off-gas of a nuclear fuel reprocessing facility will be necessary to comply with regulatory requirements regarding reprocessing facilities sited within the United States, and any iodine-containing media or solid sorbents generated by offgas abatement will require disposal. Zeolite minerals such as silver-exchanged mordenite (AgZ) have been studied as potential iodine sorbents and will contain 129 I as chemisorbed AgI. Oak Ridge National Laboratory (ORNL) has conducted several recent studies on the HIP of both iodine-loaded AgZ (I-AgZ) and other iodine-bearing zeolite minerals. The goal of these research efforts is to achieve a stable, highly leach resistant material that is reduced in volume as compared to bulk iodine-loaded I-AgZ. Through the use of HIP, it may be possible to achieve this with the addition of little or no additional materials (waste formers). Other goals for the process include that the waste form will be tolerant to high temperatures and pressures, not chemically hazardous, and that the process will result in minimal secondary waste generation. This document describes the preparation of 27 samples that are distinct from previous efforts in that they are prepared exclusively with an engineered form of AgZ that is manufactured using a binder. Iodine was incorporated solely by chemisorption. This base material is expected to be more representative of an operational system than were samples prepared previously with pure minerals.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Studies on Thermoelectric Properties of n-type Polycrystalline SnSe 1- x S x by Iodine Doping

Iodine-doped n-type SnSe polycrystalline by melting and hot pressing is prepared. The prepared material is anisotropic with a peak ZT of ≈0.8 at about 773 K measured along the hot pressing direction. This is the first report on thermoelectric properties of n-type Sn chalcogenide alloys. With increasing content of iodine, the carrier concentration changed from 2.3 × 1017 cm-3 (p-type) to 5.0 × 1015 cm-3 (n-type) then to 2.0 × 1017 cm-3 (n-type). The decent ZT is mainly attributed to the intrinsically low thermal conductivity due to the high anharmonicity of the chemical bonds like those in p-type SnSe. By alloying with 10 at% SnS, even lower thermal conductivity and an enhanced Seebeck coefficient were achieved, leading to an increased ZT of ≈1.0 at about 773 K measured also along the hot pressing direction.

36 MATERIALS SCIENCE↗

Effect of Hot Isostatic Pressing and Powder Feedstock on Porosity, Microstructure, and Mechanical Properties of Selective Laser Melted AlSi10Mg

AlSi10Mg tensile bars were additively manufactured using the powder-bed selective laser melting process. Samples were subjected to stress relief annealing and hot isostatic pressing. Tensile samples built using fresh, stored, and reused powder feedstock were characterized for microstructure, porosity, and mechanical properties. Fresh powder exhibited the best mechanical properties and lowest porosity while stored and reused powder exhibited inferior mechanical properties and higher porosity. The microstructure of stress relieved samples was fine and exhibited (001) texture in the z-build direction. Microstructure for hot isostatic pressed samples was coarsened with fainter (001) texture. To investigate surface and interior defects, scanning electron microscopy, optical fractography, and laser scanning microscopy techniques were employed. Hot isostatic pressing eliminated internal pores and reduced the size of surface porosity associated with the selective laser melting process. Hot isostatic pressing tended to increase ductility at the expense of decreasing strength. Furthermore, scatter in ductility of hot isostatic pressed parts suggests that the presence of unclosed surface porosity facilitated fracture with crack propagation inward from the surface of the part.

36 MATERIALS SCIENCE↗

Manufacture of low carbon astroloy turbine disk shapes by hot isostatic pressing. Volume 2, project 1

The performance of a hot isotatic pressed disk installed in an experimental engine and exposed to realistic operating conditions in a 150-hour engine test and a 1000 cycle endurance test is documented. Post test analysis, based on visual, fluorescent penetrant and dimensional inspection, revealed no defects in the disk and indicated that the disk performed satisfactorily.

Eng, R. D.↗

Summary of Calcine Disposal Development Using Hot Isostatic Pressing

Battelle Energy Alliance, LLC, has demonstrated the effectiveness of the hot isostatic press (HIP) process for treatment of hazardous high-level waste known as calcine that is stored at the Idaho Nuclear Technology and Engineering Center (INTEC) at Idaho National Laboratory. HIP trials performed with simulated calcines at Idaho National Laboratory’s Materials and Fuels Complex and an Australian Nuclear Science and Technology Organization facility from 2007 to 2010 produced a dense, monolithic waste form with increased chemical durability and effective (storage) volume reductions of ~10 to ~70% compared to granular calcine forms. In December 2009, the U.S. Department of Energy signed an amended Record of Decision selecting HIP technology as the treatment method for the 4,400 m3 of granular zirconia and alumina calcine stored at INTEC. Testing showed that HIP treatment reduces the risks associated with radioactive and hazardous constituent release, post-production handling, and long-term (repository) storage of calcines and would result in estimated storage cost savings in the billions of dollars. Battelle Energy Alliance has the ability to complete pilot-scale HIP processing of INTEC calcine, which is the next necessary step in implementing HIP processing as a calcine treatment method.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Magnesia tuned multi-walled carbon nanotubes–reinforced alumina nanocomposites

Magnesia tuned alumina ceramic nanocomposites, reinforced with multi-walled carbon nanotubes, were condensed using pressureless and hot-press sintering processes. Densification, microstructure and mechanical properties of the produced nanocomposites were meticulously investigated. Electron microscopy studies revealed the homogenous carbon nanotube dispersion within the alumina matrix and confirmed the retention of carbon nanotubes' distinctive tubular morphology and nanoscale features during the extreme mixing/sintering processes. Pressureless sintered nanocomposites showed meagre mechanical responses due to the poorly-integrated microstructures with a slight improvement upon magnesia addition. Conversely, both the magnesia addition and application of hot-press sintering technique resulted in the nanocomposite formation with near-theoretical densities (~ 99%), well-integrated microstructures and superior mechanical properties. Hot-press sintered nanocomposites incorporating 300 and 600 ppm magnesia exhibited an increase in hardness (10 and 11%), flexural strength (5 and 10%) and fracture toughness (15 and 20%) with respect to similar magnesia-free samples. Compared to monolithic alumina, a decent rise in fracture toughness (37%), flexural strength (22%) and hardness (20%) was observed in the hot-press sintered nanocomposites tuned with merely 600 ppm magnesia. Mechanically superior hot-press sintered magnesia tailored nanocomposites are attractive for several load-bearing structural applications. - Highlights: • MgO tailored Al{sub 2}O{sub 3}–2 wt.% CNT nanocomposites are presented. • The role of MgO and sintering on nanocomposite structures and properties was studied. • Well-dispersed CNTs maintained their morphology/structure after harsh sintering. • Hot-pressing and MgO led nanocomposites to higher properties/unified structures. • MgO tuned composites showed higher toughness (37%) and strength (22%) than Al{sub 2}O{sub 3}.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Preparation of Four Large-format Hot Isostatically Pressed I-AgZ Waste Form Samples for Performance Testing

Hot isostatic pressing (HIP) is being considered as a process to directly convert 129 I-bearing materials to a durable radiological waste form. Zeolites, specifically silver-exchanged mordenite (AgZ), have been studied extensively as potential radioactive iodine sorbents and will contain 129 I as chemisorbed AgI, a relatively insoluble compound with a high melting point. Oak Ridge National Laboratory has conducted several recent studies on the HIP of both I–AgZ and other iodine-bearing zeolites, resulting in an inventory of samples prepared with a suite of zeolites with varied iodine incorporation methods, pressing conditions, and sizes. These samples have been made available to researchers at other national laboratories in support of test method development to assess the stability of heterogenous iodine-bearing waste forms. The work described here generated four large-format HIPed I–AgZ samples. These samples are 1.5 in. diameter and 2 in. length and contain 49 g of I–AgZ. Two samples were prepared at an iodine loading of 64 mg I/g I– AgZ, and two samples were prepared at an iodine loading of 135 mg I/g I–AgZ. These two sets of duplicate samples will be made available upon request in support of iodine waste form durability method development efforts.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Powder metallurgy hot isostatic pressing - workshop report

The findings of the powder metallurgy (PM) hot isostatic pressing (HIP) workshop confirmed that the accelerated adoption of this technology requires the following action items: 1. By 2035, the HIP infrastructure must be scaled to sizes larger than 4 .0 meters for manufacturing components relevant to energy and defense industries at large. 2. The community must develop cost-effective and agile standards, qualifications, and certification pathways for these HIP parts. 3. At the same time, domestic powder production should be expanded to a wide range of metallic alloys, including Cr-Mo steels, stainless steels, and titanium- and nickel-based superalloys, as well as to emerging alloy classes in the refractory space. 4. The above initiatives can be enhanced by implementing digital modeling and controls, including AI-driven simulations, in situ monitoring, and digital twins.

36 MATERIALS SCIENCE↗

Hot isostatic pressing of silicon nitride Sisub3n4 containing zircon, or zirconia and silica

A hydrothermal synthesis apparatus with a 10 KB cylinder was used to obtain a sintered body of silicon nitride. The sintering auxiliary agents used were zircon (ZrSiO4) and a mixture of zirconia (ZrO2) and silica (SiO2). Experiments were conducted with the amounts of ZrSi04 or ArO2 and SiO2 varying over a wide range and the results compared to discover the quantity of additive which produced sintering in silicon nitride by the hot pressing method.

Somiya, S.↗