Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Fundamental Frequency”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

Extremely lightweight space telescope mirrors with integrated active figure control

A concept for an extremely lightweight primary mirror for a large space telescope is proposed. The mirror uses a sandwich structure composed of aluminum faceplates with an aluminum foam core. Modal analysis indicates that a fundamental frequency of 100 Hz can be obtained for a 6 meter diameter mirror with a tapered back and having a total mass of about 3500 kg. An array of thermal actuators embedded in the mirror corrects for figure errors. Such an active thermal figure control system does not have a quick response, but is well suited to space applications where disturbances have relatively long time constants. The advantage of thermal actuators is very high reliability, a primary concern in any space system requiring a large number of actuators.

Bely, Pierre Y.↗

Tunable far-IR laser spectroscopy of jet-cooled carbon clusters - The nu-2 bending vibration of C3

Seven rovibrational transitions of the (01/1/0)-(00/0/0) fundamental bending band of C3 have been measured with high precision with the use of a tunable far-infrared laser spectrometer. The C3 molecules were produced by laser vaporization of a graphite rod and cooled in a supersonic expansion. The astrophysically important nu-2 fundamental frequency is determined to be 63.416529(40)/cm. These measurements provide the basis for studies of C3 in the interstellar medium with far-infrared astronomy.

Schmuttenmaer, C. A.↗

On dynamics and control of multi-link flexible space manipulators

In this paper dynamics, inverse dynamics, and control problems for multi-link flexible space manipulators are presented. In deriving the flexible manipulator dynamics the following are assumed: flexible deformations are relatively small; angular rates of the links are much smaller than their fundamental frequencies; nonlinear terms (centrifugal and Coriolis forces) in the flexible manipulator model are the same as those in the rigid body model. These assumptions are reasonable for large space manipulators, such as the space crane. Flexible displacements are measured with respect to the rigid body configuration, for which a linear time-varying system is obtained. The inverse dynamics problem consists of determination of joint torques, given tip trajectory, such that joint angles in flexible configuration are equal to the angles in the rigid body configuration. The manipulator control system consists of the feedforward compensation and feedback control loops. Simulation results of a two-link space crane with large payload show that the performance of this linearized dynamics and control approach is reasonable and robust subject to parameter variations during slew operations.

Gawronski, W.↗

The effect on an acoustic wave as it traverses an unsteady expansion

The shift in fundamental frequency that occurs in acoustic waves is obtained for waves traversing an unsteady expansion. It is shown analytically that downstream of the unsteady expansion all frequencies approach one of an infinite number of discrete frequencies independent of the frequency upstream of the unsteady expansion. This theoretical analysis is used to accurately predict the period of noise observed in an expansion tube when operated at low enthalpies.

Paull, A.↗

Spectroscopic analyses of Fe and water in clays: A Martian surface weathering study

Martian surface morphology suggests the presence of liquid H2O on Mars in the past. Reflectance spectra of the Martian surface include features which correspond to the crystal field transitions of iron, as well as features supporting the presence of ice and minerals containing structural OH and surface water. Researchers initiated further spectroscopic studies of surface iron and water and structural OH in clays in order to determine what remotely obtained spectra can indicate about the presence of clays on Mars based on a clearer understanding of the factors influencing the spectral features. Current technology allows researchers to better correlate the low frequency fundamental stretching and bending vibrations of O-H bonds with the diagnostic near infrared overtone and combination bands used in mineral characterization and identification.

Bishop, J. L.↗

Annoyance caused by advanced turboprop aircraft flyover noise: Comparison of different propeller configurations

A laboratory experiment was conducted to compare the annoyance of flyover noise from advanced turboprop aircraft having different propeller configurations with the annoyance of conventional turboprop and turbofan aircraft flyover noise. A computer synthesis system was used to generate 40 realistic, time varying simulations of advanced turboprop takeoff noise. Of the 40 noises, single-rotating propeller configurations (8) and counter-rotating propeller configurations with an equal (12) and unequal (20) number of blades on each rotor were represented. Analyses found that advanced turboprops with single-rotating propellers were, on average, slightly less annoying than the other aircraft. Fundamental frequency and tone-to-broadband noise ratio affected annoyance response to advanced turboprops, but the effects varied with propeller configuration and noise metric. The addition of duration corrections and corrections for tones above 500 Hz to the noise measurement procedures improved annoyance prediction ability.

Mccurdy, David A.↗

A comparison of performance of lightweight mirrors

Four lightweight solid contoured back mirror shapes (a double arch, a single arch, a modified single arch, and a double concave mirror) and a cellular sandwich lightweight meniscus mirror, have been considered for the primary mirror of the Space Infrared Telescope Facility (SIRTF). A parametric design study using these shapes for the SIRTF 40 inch primary mirror with a focal ratio f/2 is presented. Evaluations of the optical performance and fundamental frequency analyses are performed to compare relative merits of each mirror configuration. Included in these are structural, optical, and frequency analyses for (1) different back contour shapes, (2) different number and location of the support points, and (3) two gravity orientations (ZENITH and HORIZON positions). The finite element program NASTRAN is used to obtain the structural deflections of the optical surface. For wavefront error analysis, FRINGE and PCFRINGE programs are used to evaluate the optical performance. A scaling law relating the optical and structural performance for various mirror contoured back shapes is developed.

Cho, Myung K.↗

Calculation of two-dimensional shear-driven cavity flows at high Reynolds numbers

The time-dependent Navier-Stokes equations are numerically integrated for two-dimensional incompressible viscous flow in a shear-driven square cavity. Using a time-splitting method and finite differences on a staggered mesh, the momentum and pressure equations are directly solved by a tensor product method where one finite difference direction is diagonalized by eigenvalue decomposition. The effects of increasing Reynolds number are studied and the developing boundary layer is captured by using a finely clustered mesh. At Re = 30,000 the flow is in a continuously developing unsteady regime. Power spectrum plots indicate that the unsteady flow oscillates with one fundamental frequency and exhibits some characteristics of transition between laminar and turbulent states.

Huser, A.↗

Structural verification for GAS experiments

The purpose of this paper is to assist the Get Away Special (GAS) experimenter in conducting a thorough structural verification of its experiment structural configuration, thus expediting the structural review/approval process and the safety process in general. Material selection for structural subsystems will be covered with an emphasis on fasteners (GSFC fastener integrity requirements) and primary support structures (Stress Corrosion Cracking requirements and National Space Transportation System (NSTS) requirements). Different approaches to structural verifications (tests and analyses) will be outlined especially those stemming from lessons learned on load and fundamental frequency verification. In addition, fracture control will be covered for those payloads that utilize a door assembly or modify the containment provided by the standard GAS Experiment Mounting Plate (EMP). Structural hazard assessment and the preparation of structural hazard reports will be reviewed to form a summation of structural safety issues for inclusion in the safety data package.

Peden, Mark Daniel↗

Hybrid CMS methods with model reduction for assembly of structures

Future on-orbit structures will be designed and built in several stages, each with specific control requirements. Therefore there must be a methodology which can predict the dynamic characteristics of the assembled structure, based on the dynamic characteristics of the subassemblies and their interfaces. The methodology developed by CSC to address this issue is Hybrid Component Mode Synthesis (HCMS). HCMS distinguishes itself from standard component mode synthesis algorithms in the following features: (1) it does not require the subcomponents to have displacement compatible models, which makes it ideal for analyzing the deployment of heterogeneous flexible multibody systems, (2) it incorporates a second-level model reduction scheme at the interface, which makes it much faster than other algorithms and therefore suitable for control purposes, and (3) it does answer specific questions such as 'how does the global fundamental frequency vary if I change the physical parameters of substructure k by a specified amount?'. Because it is based on an energy principle rather than displacement compatibility, this methodology can also help the designer to define an assembly process. Current and future efforts are devoted to applying the HCMS method to design and analyze docking and berthing procedures in orbital construction.

Farhat, Charbel↗

A high sensitivity real-time NVR monitor

The use of a temperature-controlled 200-MHz SAW resonator piezoelectric mass microbalance to monitor the mass of nonvolatile residue (NVR) deposited on its surface in real time is reported. The fundamental frequency of this device is mainly dependent on the configuration of the transducers and not on the thickness of the substrate. Therefore, higher operating frequencies can be achieved without reducing the thickness of the crystal. The real-time instrument was integrated onto a conventional stainless steel NVR plate and operated flawlessly over a 14-d period at Kennedy Space Center and successfully measured less than 1 ng/sq cm d NVR contamination. Contamination episodes detected by the instrument were correlated with scheduled activities on the test stand. Under the assumption of a baseline noise level of +/- 2 Hz, the absolute mass lower limit of detection would be 0.065 ng/sq cm. This would enable the detection of a daily NVR deposition rate of less than 0.1 ng/sq cm d.

Bowers, William D.↗

Weight minimization of a support structure

This paper addresses the weight minimization of a circular plate-like structure which resulted in a 26 percent weight reduction. The optimization was performed numerically with the COPES/ADS program using the modified method of feasible directions. Design parameters were the inner thickness and outer thickness of the plate with constraints on maximum yield stress and maximum transverse displacement. Also, constraints were specified for the upper and lower bounds of the fundamental frequency and plate thicknesses. The MSC/NASTRAN finite element program was used for the evaluation of response variables. Original and final designs of the plate were tested using an Instron tension-compression machine to compare finite element results to measured strain data. The difference between finite element strain components and measured strain data was within engineering accuracy.

Kluberdanz, Donald J.↗

Genetic-evolution-based optimization methods for engineering design

This paper presents the applicability of a biological model, based on genetic evolution, for engineering design optimization. Algorithms embodying the ideas of reproduction, crossover, and mutation are developed and applied to solve different types of structural optimization problems. Both continuous and discrete variable optimization problems are solved. A two-bay truss for maximum fundamental frequency is considered to demonstrate the continuous variable case. The selection of locations of actuators in an actively controlled structure, for minimum energy dissipation, is considered to illustrate the discrete variable case.

Rao, S. S.↗

LUTE telescope structural design

The major objective of the Lunar Ultraviolet Transit Experiment (LUTE) Telescope Structural Design Study was to investigate the feasibility of designing an ultralightweight 1-m aperture system within optical performance requirements and mass budget constraints. This study uses the results from our previous studies on LUTE as a basis for further developing the LUTE structural architecture. After summarizing our results in Section 2, Section 3 begins with the overall logic we used to determine which telescope 'structural form' should be adopted for further analysis and weight estimates. Specific telescope component analysis showing calculated fundamental frequencies and how they compare with our derived requirements are included. 'First-order' component stress analyses to ensure telescope optical and structural component (i.e. mirrors & main bulkhead) weights are realistic are presented. Layouts of both the primary and tertiary mirrors showing dimensions that are consistent with both our weight and frequency calculations also form part of Section 3. Section 4 presents our calculated values for the predicted thermally induced primary-to-secondary mirror despace motion due to the large temperature range over which LUTE must operate. Two different telescope design approaches (one which utilizes fused quartz metering rods and one which assumes the entire telescope is fabricated from beryllium) are considered in this analysis. We bound the secondary mirror focus mechanism range (in despace) based on these two telescope configurations. In Section 5 we show our overall design of the UVTA (Ultraviolet Telescope Assembly) via an 'exploded view' of the sub-system. The 'exploded view' is annotated to help aid in the understanding of each sub-assembly. We also include a two view layout of the UVTA from which telescope and telescope component dimensions can be measured. We conclude our study with a set of recommendations not only with respect to the LUTE structural architecture but also on other topics related to the overall feasibility of the LUTE telescope sub-system.

Ruthven, Gregory↗

Measuring atmospheric dispersion with WLRS in multiple wavelength mode

The WLRS (Wettzell Laser Ranging System) allows the simultaneous tracking of satellites on two different wavelengths. These are the fundamental frequency of Nd:YAG at 1.064 microns and the second harmonic at 532 nm. Range measurements to the satellite LAGEOS were carried out with different experimental set-ups, after developing a detector unit based on a silicon avalanche photodiode in Geiger mode, which is sufficiently sensitive in the infrared domain. An approach towards a quantitative interpretation of the data is suggested and discussed briefly.

Schreiber, Ulrich↗

Structural evaluation of concepts for a solar energy concentrator for Space Station advanced development program

Solar dynamic power systems have a higher thermodynamic efficiency than conventional photovoltaic systems; therefore they are attractive for long-term space missions with high electrical power demands. In an investigation conducted in support of a preliminary concept for Space Station Freedom, an approach for a solar dynamic power system was developed and a number of the components for the solar concentrator were fabricated for experimental evaluation. The concentrator consists of hexagonal panels comprised of triangular reflective facets which are supported by a truss. Structural analyses of the solar concentrator and the support truss were conducted using finite-element models. A number of potential component failure scenarios were postulated and the resulting structural performance was assessed. The solar concentrator and support truss were found to be adequate to meet a 1.0-Hz structural dynamics design requirement in pristine condition. However, for some of the simulated component failure conditions, the fundamental frequency dropped below the 1.0-Hz design requirement. As a result, two alternative concepts were developed and assessed. One concept incorporated a tetrahedral ring truss support for the hexagonal panels: the second incorporated a full tetrahedral truss support for the panels. The results indicate that significant improvements in stiffness can be obtained by attaching the panels to a tetrahedral truss, and that this concentrator and support truss will meet the 1.0-Hz design requirement with any of the simulated failure conditions.

Kenner, Winfred S.↗

Sensitivity of lag-damping correlations to structural and aerodynamic approximations of isolated experimental rotors in forward flight

The predictions of regressive lag-mode damping levels are correlated with the database of an isolated, soft-inplane, three-blade rotor operated untrimmed. The database was generated at the Army Aeroflightdynamics Directorate at Ames. The correlation covers a broad range of data, from near-zero thrust conditions in hover to high-thrust and highly stalled conditions in forward flight with advance ratio as high as 0.55 and shaft angle as high as 20 degrees. In the experimental rotor, the airfoil or blade portion has essentially uniform mass and stiffness distributions, but the root flexure has highly nonuniform mass and stiffness distributions. Accordingly, the structural approximations refer to four models of root-flexure-blade assembly. They range from a rigid flap-lag model to three elastic flap-lag-torsion models, which differ in modeling the root flexure. The three models of root-flexure are: three root springs in which the bending-torsion couplings are fully accounted for; a finite-length beam element with some average mass and stiffness distributions such that the fundamental frequencies match those of the experimental model; and accurate modal representation in which the actual mass and stiffness distributions of the experimental root-flexure-blade assembly are used in calculating the nonrotating mode shapes. The four models of root-flexure-blade assembly are referred to as the rigid flap-lag model, spring model, modified model and modal model. For each of these four models of the root-flexure-blade assembly, the predictions are based on the following five aerodynamic theories: ear theory, which accounts for large angle-of-attack and reverse-flow effects on lift, and has constant drag and pitching moment; quasisteady stall theory, which includes quasisteady stall lift, drag and pitching moment characteristics of the airfoil section, dynamics stall theory, which uses the ONERA dynamic stall models of lift, drag and pitching moment; dynamic wake theory, which is based on a finite-state three-dimensional wake model and includes all wake effects including both shed and trailing vorticity; and dynamics and wake theory, which combines both dynamic stall theory and dynamic wake theory and is a relatively complete aerodynamic representation.

Gaonkar, G. H.↗

Analysis of magnetic field levels at KSC

The scope of this work is to evaluate the magnetic field levels of distribution systems and other equipment at Kennedy Space Center (KSC). Magnetic fields levels in several operational areas and various facilities are investigated. Three dimensional mappings and contour are provided along with the measured data. Furthermore, the portion of magnetic fields generated by the 60 Hz fundamental frequency and the portion generated by harmonics are examined. Finally, possible mitigation techniques for attenuating fields from electric panels are discussed.

Christodoulou, Christos G.↗