Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Fuel Burn”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Spark plasma sintering of fuel meats for U 3 O 8 based dispersion fuels

Research and test reactors often use dispersion-type fuel due to its increased thermal conductivity and burn-up capabilities compared to conventional fuel. Al-U 3 O 8 (aluminumtriuranium octaoxide) dispersion fuels have several advantages over their competitors, such as higher service temperature and better stability of oxygen stoichiometry. However, the two-step fabrication of dispersion fuel causes undesirable porosity in cold-pressed fuel meats that is preserved in co-extruded fuel plates. To combat this, spark plasma sintering (SPS) was used for the fabrication of Al-15, 20, and 30 vol% U 3 O 8 and 8 and 12 vol% Mo-U 3 O 8 fuel meats for the Al-U 3 O 8 time. The in situ SPS data was used to construct and validate Master Sintering Curves (MSCs) with accuracies in Al fuels at 0.02 g/cm 3 , and Mo fuels at 0.07 and 0.17 g/cm 3 . The as-sintered fuel meats were characterised using x-ray diffraction (XRD) and scanning electron microscopy (SEM) to understand chemical and physical changes following the SPS process. The pellets exhibited very high relative densities, the U 3 O 8 was observed to undergo reduction to UO 2 .

Aluminium↗
DOE OSTI2025

High-compression implosions based on high density carbon ablator using modified drive and capsule dopant profiles

Laser-driven inertial fusion experiments have, for the first time, achieved a target gain greater than unity in a laboratory setting [Abu-Shawareb et al., Phys. Rev. Lett. 132, 065102 (2024)]. Despite this breakthrough, the burn-up fraction remains limited to about one-fourth of ideal estimates due to insufficient areal density, highlighting the potential for greater gains through enhanced compression. In our previous work, we demonstrated record-high compression of stagnated fuel in indirectly driven implosions using high-density carbon ablators. This was achieved by combining a continuous ramped pulse drive with a modified ablator dopant profile, which reduced mixing at the fuel–ablator interface and improved stability [Tommasini et al., Phys. Rev. Res. 5, L042034 (2023)]. Based on this foundation, the study presented here investigates the limits of compression achievable by combining the continuous ramped pulse drive with different dopant profiles to further minimize unstable interfaces and gradient discontinuities, thereby reducing fuel–ablator mixing. Our results demonstrate that the continuous ramped pulse consistently outperforms designs based on 3-shock drive pulses across all ablator profiles studied, with compression showing only a relatively modest dependence on dopant configurations that reduce the number of interfaces or eliminate discontinuities in the dopant gradient profile. Sub-scale experiments using the continuous ramped pulse achieved compression levels exceeding those of full-scale “HyE” implosions [Kritcher et al., Phys. Plasmas 28, 072706 (2021)] at similar adiabat, anticipating significant performance gains with increased scale, as supported by models and simulations. These findings underscore the critical role of the continuous ramped pulse in reducing mix and achieving improved compression. They also provide a foundation for future large-scale experiments to test the continuous ramped pulse design on deuterium–tritium fuel in the burn-wave propagation regime, leveraging the most effective combinations of continuous ramped pulse and dopant profiles identified in this study.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Droplet burning of n-butyl acetate/n-heptane mixtures in the standard atmosphere: experiments and numerical modeling

Blending petroleum fuels with oxygenates is a common approach to stem the depletion of crude oil while also mitigating the impact of their combustion on the environment. It has recently been considered that n-butyl acetate (BA, C6H12O2 , boiling point of 399K) could be a viable oxygenate additive to diesel fuel. In this application it is important to determine the influence of the fractional amount of BA on burning of the mixture. This presentation considers this problem from an experimental and computational approach using n-heptane (C7H14 , boiling point of 372K) as an essentially single component surrogate for diesel fuel. The burning configuration considered was ostensibly spherical symmetry as promoted by burning droplets under conditions where forced and natural convection effects were minimized. In this configuration the droplet and flame are concentric spheres and soot aggregates are trapped in a shell structure between the droplet and flame. Measurements were made of the droplet, flame and soot shell diameters through video imaging of the burning process. The experimental results were used to validate a detailed numerical model of the spherically symmetric droplet burning process that incorporated a consistent combustion kinetic mechanism for BA/heptane mixtures, comprised of 402 species and 16,872 reactions inclusive of soot chemistry. A model for soot formation was also included in the simulation to predict formation of the soot shell. The simulations agreed well with measured droplet and flame diameters. It was found both experimentally and computationally that adding BA to heptane had a minimal effect on the mixture burning rate, while the flame was positioned closer to the droplet surface and the simulated soot volume fraction decreased. The implications of these results are discussed for using BA as a potential additive to diesel fuel.

09 BIOMASS FUELS↗
DOE OSTI2024

Biofuels as Heavy Fuel Oil Substitutes in the Maritime Sector: Findings and Potential Pathways

The United States Department of Energy has commissioned four national laboratories to evaluate the feasibility of biofuels in the maritime sector. This effort is briefly described including the overall project goals, structure and aims. The large two-stroke crosshead engines used to power large merchant vessels were of particular interest since they can burn lower combustion quality fuels relative to four-stroke engines. This characteristic allows for consideration of pyrolysis oils and hydrothermal liquefaction (HTL) oils which are feedstock agnostic and, in the raw state, are more economical compared to distillate drop-in fuels. Pyrolysis and HTL oils are collectively known as bio-intermediates since they require additional processing for use in distillate fuel systems. The key limiting feature is that these bio-intermediate fuels will cause asphaltene precipitation when blended with heavy fuel oils (HFOs) such as very low sulfur fuel oil (VLSFO) unless they are upgraded to remove water and oxygenates. Economics are the key driver at this point in time, and preliminary techno-economic analyses (TEAs) indicate that bio-intermediates have potentially lower cost relative to other biofuels such as biodiesel and renewable diesel. Additionally, life cycle analyses (LCAs) of feedstocks and pathways show the life cycle carbon reduction benefit relative to heavy fuel oils. In addition to TEA and LCA results, we also present on the technical feasibility of these fuels. These studies have focused on the properties of biofuel blends with VLSFO that are critical to the fuel systems of maritime vessels fueled with HFOs. These properties include the compatibility with fuel system metals, viscosity, and blend stability. Aging studies with blends of VLSFO with biodiesel, HTL, and pyrolysis oils are also presented. Future efforts being planned to conduct additional biofuel testing, including the use of biofuels as pilot fuels in zero carbon shipping options fueled with ammonia and methanol, ship-based demonstrations, and bioresource competition studies.

Kass, Michael↗
DOE OSTI2022

Evaluation of the energy balance of chemical looping combustion of solid fuels using CuO-based oxygen carriers

Chemical looping combustion (CLC) can inherently capture the CO2 generated during thermal energy production. When using CuO-based oxygen carriers, the reactions in both the fuel reactor (FR) and air reactor (AR) are exothermic, facilitating autothermal operation. To prevent the oxygen carrier from becoming agglomerated while ensuring a sufficient oxygen release rate, it is necessary to predict the FR temperature and remove an appropriate amount of heat from the AR when burning high-rank fuels. Here in this work, the energy balance of a CuO-based CLC system firing various solid fuels (biomass, coal, and petroleum coke) was investigated by establishing a thermodynamic model using FactSage. The energy distribution characteristics of the FR were quantified based on a virtual five-step thermodynamic sequence. The effects of fuel properties, oxygen carrier properties, and operating conditions on the energy balance were evaluated systematically. The results indicate that the temperature difference between the FR and AR is not very sensitive to the heating value of the fuel, while the CuO loading of the oxygen carrier, the heat capacity of the support material, and the flow rate of the fluidizing gas have significant impact. The insights obtained in this work will help improve the design and heat management of CLC.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Synchrotron micro-computed tomography analysis of neutron-irradiated U-Mo fuel

The three-dimensional (3D) microstructure of neutron-irradiated uranium-10 wt.% molybdenum (U-10Mo) fuel with a burn-up of 9.8 × 10 21 fissions/cm 3 was characterized using a novel, multi-modal synchrotron micro-computed tomography approach combining propagation-based phase-contrast enhanced and absorption contrast techniques. The porosity development, porosity interconnectedness, swelling, composition, local thickness of the zirconium (Zr) diffusion barrier, and the influence of the fuel–cladding interaction on the local composition and pore morphology, were uniquely determined in 3D. Two cuboids were produced using a focused ion beam-scanning electron microscope at the Zr diffusion barrier–fuel interface and in the bulk fuel. The bulk fuel sample swelled by 53.3 [+9.7/−3.1]%, while the fuel near the Zr–fuel interface swelled by 63.3 [+14.7/−7.2]%. The average local thickness of the Zr diffusion barrier decreased by 53 %, compared to the expected pre-irradiated thickness. Four pore morphology regions were identified initiating parallel to the fuel–Zr interaction region: (1) an interaction layer of suppressed porosity, (2) a layer of elongated and interconnected porosity, (3) a transition zone of low porosity, and (4) a layer of unoriented porosity representative of the bulk fuel behavior. The increase in porosity near the diffusion barrier corresponded to a higher U concentration compared to that in the bulk fuel. The interconnected porosity in the fuel near the diffusion barrier was extensive and oriented parallel to the diffusion barrier, while the bulk fuel had more compact and isolated pore networks. The interaction layer, despite having suppressed porosity, was nearly 100 wt.% U. Porosity suppression at the diffusion barrier corresponds to the expected reduction in radiation-driven diffusion of Xe at the interface despite the anticipated increase in fission product nucleation originating from a higher U concentration. In conclusion, the novel 3D insights of the porosity, swelling, and compositional variations characterized herein can improve the fidelity of fuel performance codes for proliferation-resistant fuels for research and test reactors.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Thermal Model Heat Rate Predictions of the AGR-5/6/7 Experiment

Several fuel and material irradiation experiments have been planned for the U.S. Department of Energy Advanced Gas Reactor Fuel Development and Qualification Program, which supports the development and qualification of tristructural isotropic (TRISO) coated particle fuel for use in high-temperature gas-cooled reactors. The goals of these experiments are to provide irradiation performance data to support fuel process development, qualify fuel for normal operating conditions, support development of fuel performance models and codes, and provide irradiated fuel and materials for post-irradiation examination and safety testing. Originally planned and named as separate fuel experiments, but subsequently combined into a single test train. AGR-5/6/7 will test low-enriched uranium oxycarbide (UCO – a heterogeneous mixture of uranium oxide and uranium carbide) TRISO fuel. The AGR-5/6 portion of the experiment will provide data to support qualification of the selected reference fuel design, while the AGR-7 portion will serve as a margin test, irradiating the fuel beyond normal operating conditions. During irradiation, the temperature in each capsule is controlled by varying the helium / neon gas mixture flowing through the capsule until the desired thermocouple temperature is reached. Further adjustments can be made by changing the lobe power and the neutron filter. Three neutron filters are available to use as the experiment burns up the fissionable fuel. A thermal finite element model has been created for the five capsules comprising the AGR-5/6/7 experiment. Heat rates from a physics analysis are imported into the model along with fast neutron fluence. Graphite shrinkage due to the fast neutron fluence is incorporated into the model. Gas gaps change as a function of fast neutron fluence. Radiation heat transfer is a major contributor in this model. This is a large model with more than 1 million finite element brick elements. More than 150 different parts are modeled in the finite element model and communicate with each other from a heat transfer sense. More than 50 thermocouples are used in the experiment and are compared to actual measurements. The experiment is composed of five separate stainless steel capsules all welded together. This paper presents a method used to predict the gas mixture in the event that all of the thermocouples fail in a particular capsule. Curve fitting of heat rates from previous cycles and projecting them into the future is the basis of the method.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Point Cloud Based Mapping of Understory Shrub Fuel Distribution, Estimation of Fuel Consumption and Relationship to Pyrolysis Gas Emissions on Experimental Prescribed Burns

Forest fires spread via production and combustion of pyrolysis gases in the understory. The goal of the present paper is to understand the spatial location, distribution, and fraction (relative to the overstory) of understory plants, in this case, sparkleberry shrub, namely its degree of understory consumption upon burn, and to search for correlations between the degree of shrub consumption to the composition of emitted pyrolysis gases. Data were collected in situ at seven small experimental prescribed burns at Ft. Jackson, an army base in South Carolina, USA. Using airborne laser scanning (ALS) to map overstory tree crowns and terrestrial laser scanning (TLS) to characterize understory shrub fuel density, both pre- and postburn estimates of sparkleberry coverage were obtained. Sparkleberry clump polygons were manually digitized from a UAV-derived orthoimage of the understory and intersected with the TLS point cloud-derived rasters of pre- and postburn shrub fuel bulk density; these were compared in relation to overstory crown cover as well as to ground truth. Shrub fuel consumption was estimated from the digitized images; sparkleberry clump distributions were generally found to not correlate well to the overstory tree crowns, suggesting it is shade-tolerant. Moreover, no relationship was found between the magnitude of the fuel consumption and the chemical composition of pyrolysis gases, even though mixing ratios of 25 individual gases were measured.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

AmeriFlux FLUXNET-1F US-KS2 Kennedy Space Center (scrub oak)

This is the AmeriFlux Management Project (AMP) created FLUXNET-1F version of the carbon flux data for the site US-KS2 Kennedy Space Center (scrub oak). This is the FLUXNET version of the carbon flux data for the site US-KS2 Kennedy Space Center (scrub oak) produced by applying the standard ONEFlux (1F) software. Site Description - The Kennedy Space Center Scrub Oak site is located within the Merritt Island National Wildlife Refuge at the Kennedy Space Center (KSC) on the east coast of central Florida. Situated in a 10 ha scrub oak ecosystem, the surrounding stand was completely burned by a prescribed fire in 1996. The purpose of the burn was to control understory fuel load, which has been a common practice since 1969. Within a few weeks of the 1996 burn, the stand began to naturally regenerate from roots and rhizomes. Most scrub oak stands in the region undergo a 7 to 10 year disturbance cycle, mostly related to fire or hurricane activity. A severe drought gripped most of Florida beginning in 1998 until the later half of 2001 resulting in four years of relatively low amount of annual rainfall. Exceptionally high annual rainfall amount in 2004 was the result of a pair of hurricanes that hit the area in August and September of 2004. Prevaling wind directions for the site are as follows: W to NW in the winter, afternoon E sea breeze in the summer.

Drake, Bert↗
DOE OSTI2021

Deep-learning-enabled Bayesian inference of fuel magnetization in magnetized liner inertial fusion

Fuel magnetization in magneto-inertial fusion (MIF) experiments improves charged burn product confinement, reducing requirements on fuel areal density and pressure to achieve self-heating. By elongating the path length of 1.01 MeV tritons produced in a pure deuterium fusion plasma, magnetization enhances the probability for deuterium–tritium reactions producing 11.8-17.1 MeV neutrons. Nuclear diagnostics thus enable a sensitive probe of magnetization. Characterization of magnetization, including uncertainty quantification, is crucial for understanding the physics governing target performance in MIF platforms, such as magnetized liner inertial fusion (MagLIF) experiments conducted at Sandia National Laboratories, Z-facility. We demonstrate a deep-learned surrogate of a physics-based model of nuclear measurements. A single model evaluation is reduced from O ( 10 – 100 ) (10–100) CPU hours on a high-performance computing cluster down to O ( 10 – 100 ) (10) ms on a laptop. This enables a Bayesian inference of magnetization, rigorously accounting for uncertainties from surrogate modeling and noisy nuclear measurements. The approach is validated by testing on synthetic data and comparing with a previous study. We analyze a series of MagLIF experiments systematically varying preheat, resulting in the first ever systematic experimental study of magnetic confinement properties of the fuel plasma as a function of fundamental inputs on any neutron-producing MIF platform. We demonstrate that magnetization decreases from B R ∼ 0.2 ~0.5 to B R ∼ 0.2 ~0.2 MG cm as laser preheat energy deposited increases from E preheat ∼ 460 ~460 J to E preheat ∼ 460 ~1.4 kJ. This trend is consistent with 2D LASNEX simulations showing Nernst advection of the magnetic field out of the hot fuel and diffusion into the target liner.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

A Novel Catalytic Membrane Reactor for DME Synthesis from Renewable Resources

Production of liquid fuels or chemicals from CO 2 (captured from the air or flue gases) and renewable hydrogen presents a new approach to producing clean fuels domestically. While significant progress has been made in the area of renewable electricity generation from solar and wind, a large gap remains with respect to the production of renewable liquid fuels/chemicals. Other processes for producing liquid fuels/chemicals from renewable electricity are constrained by thermodynamic limitations, making them prohibitively expensive and impractical. The team is overcoming these limitations and developing catalytic membrane reactor processes with high yields and low energy penalties. Supported by the Advanced Research Projects Agency-Energy (ARPA-E) of the US Department of Energy (DOE), GTI Energy and partners have been developing a technology for the production of renewable dimethyl ether (DME) from carbon dioxide (CO 2 ) and renewable hydrogen (H 2 ) using a novel catalytic membrane reactor and demonstration of this system at a scale of 1 kg/day. DME is a clean-burning, non-toxic fuel with a high cetane value (55-60), making it an excellent diesel alternative. DME can be stored as a liquid under moderate pressure, eliminating the need for the high-pressure containers used for CNG or cryogenics, as in the case of LNG. DME is also approved as a renewable fuel under the U.S. Environmental Protection Agency’s Renewable Fuels Standard (RFS), making it eligible for Renewable Identification Numbers (RINs) credits. By producing DME through the catalytic conversion of captured CO 2 and renewable H 2 , this process will produce renewable liquid transportation fuel and a means of large-scale utilization of captured CO 2 . In the DME synthesis process, CO 2 and H 2 are fed to a hollow fiber catalytic membrane reactor at 300-600 psig that contains a bi-functional catalyst that combines two reactions, methanol synthesis (CO 2 + 3H 2 → CH 3 OH + H 2 O) and methanol dehydration (2CH 3 OH → CH 3 OCH 3 + H 2 O), into a one-step process to produce DME. The bifunctional catalyst converts methanol to DME, enabling higher overall CO 2 conversion. A Cu/ZnO/ZrO 2 /Al 2 O 3 (CZZA) catalyst is used for methanol synthesis and is coupled with a zeolite catalyst H-ZSM-5 for dehydration. This one-step process intensifies a process that would otherwise require multiple reaction steps. However, combining these two reactions results in increased water production which inhibits catalytic activity. Here, the Na + -gated, water-transport membrane (Science, vol. 367, pp. 667, 2020), removes water in situ, shifting the thermodynamic equilibrium towards product formation while decreasing kinetic inhibition from water adsorption onto the catalyst surface. The Na + gated, water-transport nanochannel membrane showed H 2 O/CO 2 selectivity of 560 at 250 °C and 300 psig for H 2 O/CO 2 /CO/H 2 /MeOH gas mixtures. The selectivities of H 2 O/H 2 , H 2 O/CO, and H 2 O/MeOH were 190, 170, and 80, respectively. In a laboratory-scale membrane reactor, DME synthesis testing using this membrane, a DME production rate of 440 g DME /kg cat /h was achieved at 260 °C and 550 psig. Compared to the packed bed reactor, the CO 2 conversion and DME production rate in the membrane reactor were 80% and three times higher, respectively. A prototype test system (1 kg/day) was designed, constructed, and tested. A DME production rate of 1.31 kg/day and a DME productivity of 360 g/h/kg were achieved in the prototype membrane reactor. Good stability was demonstrated during 150-h continuous operation and multiple startups/shutdowns tests.

10 SYNTHETIC FUELS↗
DOE OSTI2024

Summary of Leach-Burn-Leach Round-Robin Test Results

Tristructural isotropic (TRISO) coated particle fuel is of interest to multiple member states associated with the Generation IV International Forum (GIF). Qualification and acceptance testing of TRISO fuel includes the determination of particle defect fractions and impurities in the as-fabricated TRISO fuel particle and/or composited fuel form, which are typically determined using burn-leach (BL) or leach-burn-leach (LBL) analysis methods. A round-robin test focusing on LBL analysis was undertaken by the GIF Very High Temperature Reactor System Fuel and Fuel Cycle Project Management Board. Participating in this LBL round-robin test were research staff from the Institute of Nuclear and New Energy Technology (INET) in the People’s Republic of China, the Korean Atomic Energy Research Institute (KAERI) in the Republic of Korea, and Oak Ridge National Laboratory (ORNL) in the United States of America. The motivation of this LBL benchmarking exercise was to explore consistency in results generated by LBL and to elucidate the potential influence of variations in the procedures used by the participating members on the accurate determination of the measured fuel properties.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Reactor and fuel cycle performance of light water reactor fuel with 235 U enrichments above 5%

Recent advances in nuclear fuel materials research, particularly on the topic of accident-tolerant fuels, have brought up potential opportunities for expanding the operating envelope of existing light water reactors. As many of the performance improvements offered by these technologies may be most fully realized by increasing fuel enrichment beyond the standard 5% limit, this paper examines the potential reactor performance and fuel cycle performance of low-enriched uranium oxide fueled light water reactors by generically considering pressurized water reactors with 235 U enrichment from 5 to 7%. Advanced cladding, including accident-tolerant cladding, has the potential to increase fuel burnup limits related to hydrogen in the cladding that coincide with those limits associated with end-of-life reactivity. Therefore, higher enrichment will be necessary in order to realize the higher fuel burnups. This work includes evaluation of the fuel cycle length, discharge burnup, reactivity coefficients, and fuel cycle performance, including radioactive waste and environmental impact metrics per unit energy generated. The analysis was performed using the evaluation metrics from the US Department of Energy Office of Nuclear Energy Fuel Cycle Evaluation and Screening Study. The reactor performance and safety analysis show that enrichments between 5 and 7% would have similar fuel temperature and moderator temperature coefficients. However, the soluble boron coefficient would decrease in magnitude, requiring more corrosive boric acid in the coolant or other methods of reactivity control during the fuel cycle. At these higher enrichments the maximum burnup at the rim of the fuel pellet would increase by almost a factor of two, which is expected to impact the formation of high-burnup structure in the fuel and the corresponding thermo-mechanical fuel properties. The fuel cycle performance assessment shows that increasing enrichment reduces the quantity of high-level waste disposed per unit energy generated, but it increases the natural resource requirements normalized to a gigawatt-electricity-per-year basis. Another impact is the slightly higher discharge burnup, resulting in somewhat different activity levels of the spent nuclear fuel and high-level waste radioactivity at 100 and 100,000 years after fuel discharge. The environmental impacts—including land use, water use, carbon emission, and radiological exposure—are of the same magnitude per unit energy generated. Finally, however, the impacts are distributed differently. Less than 5% enrichment has marginally more impact on the back-end of the fuel cycle, and greater than 5% enrichment has marginally more impact on the front-end of the fuel cycle. Ultimately, no neutronic or reactor safety hindrances to employing light water reactor fuel with enrichments greater than 5% are identified; given the achievable reactor performance benefits with advanced fuels, further practical exploration of increased enrichment fuel is recommended.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

Experimental quantification of the impact of heterogeneous mix on thermonuclear burn

In inertial confinement fusion, deuterium–tritium (DT) fuel is brought to densities and temperatures where fusion ignition occurs. However, mixing of the ablator material into the fuel may prevent ignition by diluting and cooling the fuel. MARBLE experiments at the National Ignition Facility provide new insight into how mixing affects thermonuclear burn. These experiments use laser-driven capsules containing deuterated plastic foam and tritium gas. Embedded within the foam are voids of known sizes and locations, which control the degree of heterogeneity of the fuel. Initially, the reactants are separated, with tritium concentrated in the voids and deuterium in the foam. During the implosion, mixing occurs between the foam and gas materials, leading to DT fusion reactions in the mixed region. Here, it is shown that by measuring the ratios of DT and deuterium–deuterium neutron yields for different macropore sizes and gas compositions, the effects of mix heterogeneity on thermonuclear burn may be quantified, supporting an improved understanding of these effects.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Microphysical properties of atmospheric soot and organic particles: measurements, modeling, and impacts

Atmospheric soot and organic particles from fossil fuel combustion and biomass burning modify Earth’s climate through their interactions with solar radiation and through modifications of cloud properties by acting as cloud condensation nuclei and ice nucleating particles. Recent advancements in understanding their individual properties and microscopic composition have led to heightened interest in their microphysical properties. This review article provides an overview of current advanced microscopic measurements and offers insights into future avenues for studying microphysical properties of these particles. To quantify soot morphology and ageing, fractal dimension ( D f ) is a commonly employed quantitative metric which allows to characterize morphologies of soot aggregates and their modifications in relation to ageing factors like internal mixing state, core-shell structures, phase, and composition heterogeneity. Models have been developed to incorporate D f and mixing diversity metrics of aged soot particles, enabling quantitative assessment of their optical absorption and radiative forcing effects. The microphysical properties of soot and organic particles are complex and they are influenced by particle sources, ageing process, and meteorological conditions. Furthermore, soluble organic particles exhibit diverse forms and can engage in liquid–liquid phase separation with sulfate and nitrate components. Primary carbonaceous particles such as tar balls and soot warrant further attention due to their strong light absorbing properties, presence of toxic organic constituents, and small size, which can impact human health. Future research needs include both atmospheric measurements and modeling approaches, focusing on changes in the mixing structures of soot and organic particle ensembles, their effects on climate dynamics and human health.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Methane storage in flexible and dynamical metal–organic frameworks

Recently, there has been significant interest in methane as an abundant and cleaner burning alternative to fossil fuels. Consequently, the design of media capable of the storage of methane under practical conditions has become an area of significant interest to the scientific community. While metal−organic frameworks have seen pronounced examination for this application, flexible metal−organic framework variants have been little examined despite having tremendous promise for methane storage applications. This work provides an overview of the current state of the art regarding the investigation of these systems for the purpose of providing a baseline for future research.

Forrest, Katherine A.↗
DOE OSTI2024

Verification of a Monte Carlo binary collision model for simulating elastic and inelastic collisions in particle-in-cell simulations

We present the development and verification of a Monte Carlo binary collision model for simulating elastic and inelastic collisions in particle-in-cell simulations. We apply the corrected binary collision model originally developed for charged-particles collisions to all considered scattering channels, including Coulomb collisions, elastic neutral–neutral and charged–neutral collisions, ionization, excitation, and fusion. The model's implementation is described and verified through a series of simulations, including charged- and neutral-particle thermal equilibration, slowing of electrons in warm solid-density aluminum, collisional damping of a Langmuir wave, helium gas breakdown in an applied electric field, and thermonuclear and beam–target fusion. Then, we demonstrate the model within simulations of hydrogen plasma formation in the Princeton Field-Reversed Configuration as well as of the burning of aneutronic fusion fuel p-11B. The latter includes measurement of the fusion power density in a low-density plasma and fusion production due to the stopping of a proton ignitor beam in a compressed boron target.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗