Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Extrusion Process”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Dissimilar metals joint evaluation

Dissimilar metals tubular joints between 2219-T851 aluminum alloy and 304L stainless steel were fabricated and tested to evaluate bonding processes. Joints were fabricated by four processes: (1) inertia (friction) weldings, where the metals are spun and forced together to create the weld; (2) explosive welding, where the metals are impacted together at high velocity; (3) co-extrusion, where the metals are extruded in contact at high temperature to promote diffusion; and (4) swaging, where residual stresses in the metals after a stretching operation maintain forced contact in mutual shear areas. Fifteen joints of each type were prepared and evaluated in a 6.35 cm (2.50 in.) O.D. size, with 0.32 cm (0.13 in.) wall thickness, and 7.6 cm (3.0 in) total length. The joints were tested to evaluate their ability to withstand pressure cycle, thermal cycle, galvanic corrosion and burst tests. Leakage tests and other non-destructive test techniques were used to evaluate the behavior of the joints, and the microstructure of the bond areas was analyzed.

Wakefield, M. E.↗
NASA NTRS1983

Influence of thermomechanical processing on elevated temperature slow plastic flow properties of B2 aluminide Fe-39.8at.% Al

A study of the elevated temperature slow plastic flow properties of the B2 aluminide Fe-39.8at.% Al was undertaken. Polycrystalline materials possessing several different microstructures were produced by the hot extrusion of prealloyed powder and, in some cases, postextrusion heat treatments. Compression tests were conducted in air at 1200, 1300 and 1400 K. Such testing revealed that the extrusion temperature affected the active deformation mechanisms where material extruded at 1505 K had a stress exponent about twice that of the intermetallic extruded at 1200 K. Grain size refinement to about 10 microns was found to strengthen the Fe-39.8at.% Al material; unfortunately, the effectiveness of such strengthening is limited to a homologous temperature of about 0.75 for strain rates of commercial interest (less than 10 to the -7th/sec).

Whittenberger, J. D.↗
NASA NTRS1997

Microstructure and Mechanical Properties of Vacuum Plasma Sprayed Cu-8Cr-4Nb

This paper compares the tensile properties of Cu-8Cr-4Nb material produced by VPS to material previously produced by extrusion. The microstructure of the VPS material is also presented. The combustion chamber liner of rocket motors represents an extreme materials application. The liner hot wall is exposed to a 2760 C (5000 F) flame while the cold side is exposed to cryogenic hydrogen liquid. Materials for use in the combustion chamber liner require a combination of high temperature strength, creep resistance, and low cycle fatigue resistance along with high thermal conductivity. The hot side is also subject to localized cycles between reducing and oxidizing environments that degrade the liner by a process called blanching. A new Cu-8 at.% Cr-4 at% Nb (Cu-8Cr-4Nb) alloy has been developed at NASA Lewis Research Center as a replacement for the currently used alloy, NARloy-z (Cu-3 wt.% Ag-0.5 wt.% Zr). The alloy is strengthened by a fine dispersion of Cr2Nb particles. The alloy has better mechanical properties than NARloy-Z while retaining most of the thermal conductivity of pure copper. The alloy has been successfully consolidated by extrusion and hot isostatic pressing (HIPing). However, vacuum plasma spraying (VPS) offers several advantages over prior consolidation methods. VPS can produce a near net shape piece with the profile of the liner. In addition, oxidation resistant and thermal barrier coatings can be incorporated as an integral part of the liner hot wall during the VPS deposition. The low oxygen VPS Cu-8Cr-4Nb exhibits a higher strength than Cu-8Cr-4Nb produced by extrusion at elevated temperatures and a comparable strength at room temperature. Moduli and ductility were not significantly different. However, the ability to produce parts to near-net shape and maintain the good elevated temperature tensile properties of the extruded Cu-8Cr-4Nb makes VPS an attractive processing method for fabricating rocket engine combustion liners.

Holmes, Richard↗
NASA NTRS1985

The Presidents' Day cyclone of 18-19 February 1979 - Influence of upstream trough amplification and associated tropopause folding on rapid cyclogenesis

The Presidents' Day cyclone of 18-19 February, 1979 is analyzed based on conventional radiosonde data, infrared and visible satellite imagery, water vapor images and ozone measurement. The well-known synoptic-scale characteristics of the PJ-trough system are described, and evidence for the development of the tropopause fold are presented. Processes contributing to the formation of the fold are discussed in terms of an evaluation of the Sawyer-Eliassen circulation equation and a diagnostic evaluation of the ageostrophic winds and vertical motion near the polar jet streak. The documentation of stratospheric extrusions and their possible role in cyclogenesis is reviewed, and Eulerian and Lagrangian diagnostics are used to establish a connection between the tropopause fold associated with the polar jet streak and rapid cyclogenesis along the East Coast. Conservation of potential vorticity expressed in isentropic coordinates is used as a constraint from which to view cyclogenesis.

Uccellini, L. W.↗
NASA NTRS2014

Badger COMET Compartmentalized Onboard Material Extrusion Technology

In response to the 2014 NASA Academic Innovation Challenge, the University of Wisconsin – Madison team presents the design of a collapsible Fused Deposition Modeling (FDM) system for in situ manufacturing in a space habitat environment, the Badger Compartmentalized Onboard Material Extrusion Technology (COMET). The proposed mechanism incorporates one year of design and testing on an array of current additive manufacturing techniques, with the goal of providing a reliable and maintainable manufacturing solution. Seven Level 1 requirements were employed to guide the design process, based on information in the challenge, communications with NASA, and the evolving systems feedback of project work groups. These requirements provided a baseline for the development of the System Requirements Document (SRD, Appendix I), which framed the design of the system. The design requirements deemed critical to the success of the systems are as follows: - The system shall compose an FDM workstation capable of producing parts within industry standard tolerances. - The system shall reduce to a minimum of 50 percent or less of its deployed volume when not in use, and must collapse without the need for disassembly. - The system shall meet all relevant NASA safety and functional standards. The final design for the Badger COMET was selected from multiple design iterations, which balanced the critical design requirements listed above with system reliability, with the final goal of providing a minimal system weight. The system collapses in the vertical direction, allowing for a maximum reduction in volume. Guide rods and precision, anti-backlash lead screws provide all linear movement in the device. Stepper motors were chosen to actuate each system axis, due to their high precision and repeatable accuracy. The system is controlled through an on-board computer system and embedded electronics package.

Frederick T. Elder↗
NASA NTRS1998

Mechanistic Models of Friction Stir Welding

Friction stir welding is a welding process developed at The Welding Institute (TWI) in England. The method uses very large strain plastic deformation of the material to join two pieces of metal together. The material is deformed using a tool which is forced between the two pieces which rotates causing a bond. Beyond this, very little is actually known although many people working in the field are willing to speculate on the detailed mechanisms involved. Some measurements made using sacrificial thermocouples at the weld joint indicate that the maximum temperature during the weld process is on the order of 370C - well below the melting temperature of the material. However, at this temperature, the material properties are highly temperature dependent, and the yield stress is approximately an order of magnitude less at this temperature than it is at room temperature. As expected, there are many interpretations of the physical mechanisms occurring during the weld process. Although there is very little published concerned with FSW, some of the anecdotal theories will be described. One describes the primary mechanism as frictional heating at the front of the tool caused by slip between the tool and the material. At elevated temperatures, the weld material becomes soft and deforms around the tool but not essentially altered by the tool rotation, similar to an extrusion. As the material meets again at the rear of the tool, the temperatures and pressures are sufficient to cause the material to bond. All other structures seen are secondary and unimportant. Another theory examined last summer at NASA's Marshall Space Flight Center (MSFC) was that there was no slip between the tool and the material resulting in a rotating mass of plastic weld material traveling at a variety of angular velocities - the greatest at the tool surface diminishing to zero at the outer edge of the plastic mass surrounding the tool. This conceptual model was followed by simplified calculations which showed that the balance of moments through the weld plug was not possible under steady state conditions and realistic temperature profiles. This led to some consideration of a quasi-steady oscillating process. Later when force measurements became available some models were modified and new ones were proposed.

Stewart, Michael B.↗
NASA NTRS1989

Hydrogen-isotope evidence for extrusion mechanisms of the Mount St Helens lava dome

Hydrogen isotope analyses were used to determine water content and deuterium content for 18 samples of the Mount St Helens dome dacite in an attempt to identify the triggering mechanisms for periodic dome-building eruptions of lava. These isotope data, the first ever collected from an active lava dome, suggest a steady-state process of magma evolution combining crystallization-induced volatile production in the chamber with three different degassing mechanisms: closed-system volatile loss in the magma chamber, open-system volatile release during ascent, and kinetically controlled degassing upon eruption at the surface. The data suggest the future dome-building eruptions may require a new influx of volatile-rich magma into the chamber.

Anderson, Steven W.↗
NASA NTRS1980

Lunar mare domes - Classification and modes of origin

In this paper, lunar mare domes (LMDs) are classified according to morphologic and morphometric (primarily diameter) characteristics, and consideration is given to their origin and role in lunar surface processes. In general, they occur either as low, flat, circular structures with convex shapes, slopes less than about 5 deg, and display summit craters, or as irregular structures often adjacent to highland regions and rarely containing summit craters. It is found that LMDs originate through extrusion of lavas through vents to produce low lava shields, or through flooding and draping of preexisting topography to produce kipukas and irregular domes. Smooth, vent-related mare domes range from about 3-17 km in diameter and up to several hundred meters in elevation; they are similar in morphology to small terrestrial lava shields.

Head, J. W.↗
NASA NTRS1980

Geochemical anomalies on the eastern limb and farside of the moon

A variety of orbital geochemistry and photogeologic data was used to investigate major geochemical anomalies on the east limb and farside of the moon and to determine the processes responsible for their formation. These anomalies are located in the following regions: (1) near Langemak crater, (2) Mare Marginis, (3) Balmer crater, (4) terrain north of Taruntius crater, and (5) Van de Graaff. It was concluded that these anomalies are related to episodes of extrusive igneous activity which produced deposits with a variety of ages and compositions. Some of the associated volcanic deposits exhibit albedos and surface morphologies similar to those of the nearside maria, while others are now thinly covered by highland debris and are commonly represented by light plains units which exhibit clusters of dark-haloed craters. Little evidence was found for a genuine episode of highland volcanism (e.g., Apollo 15 KREEP basalt, highland basalt, etc.). The existence of intermediate basalts on the eastern limb and farside supports previous suggestions that KREEP-like volcanism was not limited to a small area of the lunar nearside. Eastern limb and farside volcanic activity has been more extensive in both space and time and has produced a greater variety of compositions than has previously been thought. Since thinly covered basaltic units can exert a strong influence on regional surface chemistry as determined from orbit, caution is urged in interpreting the surface compositions of highland terrains which exhibit a high density of dark-haloed impact craters.

Hawke, B. R.↗
NASA NTRS2000

Flow in the Proximity of the Pin-Tool in Friction Stir Welding and Its Relation to Weld Homogeneity

In the Friction Stir Welding (FSW) process a rotating pin inserted into a seam literally stirs the metal from each side of the seam together. It is proposed that the flow in the vicinity of the pin-tool comprises a primary rapid shear over a cylindrical envelope covering the pin-tool and a relatively slow secondary flow taking the form of a ring vortex about the tool circumference. This model is consistent with a plastic characterization of metal flow, where discontinuities in shear flow are allowed but not viscous effects. It is consistent with experiments employing several different kinds of tracer: atomic markers, shot, and wire. If a rotating disc with angular velocity w is superposed on a translating continuum with linear velocity omega, the trajectories of tracer points become circular arcs centered upon a point displaced laterally a distance v/omega from the center of rotation of the disc in the direction of the advancing side of the disc. In the present model a stream of metal approaching the tool (taken as the coordinate system of observation) is sheared at the slip surface, rapidly rotated around the tool, sheared again on the opposite side of the tool, and deposited in the wake of the tool. Local shearing rates are high, comparable to metal cutting in this model. The flow patterns in the vicinity of the pin-tool determine the level of homogenization and dispersal of contaminants that occurs in the FSW process. The approaching metal streams enfold one another as they are rotated around the tool. Neglecting mixing they return to the same lateral position in the wake of the tool preserving lateral tracer positions as if the metal had flowed past the tool like an extrusion instead of being rotated around it. (The seam is, however, obliterated.) The metal stream of thickness approximately that of the tool diameter D is wiped past the tool at elevated temperatures drawn out to a thickness of v/2(omega) in the wiping zone. Mixing distances in the wiping zone are multiplied in the unfolded metal. Inhomogeneities on a smaller scale than the mixing length are obliterated, but structure on a larger scale may be transmitted to the wake of a FSW weld.

Nunes, Arthur C., Jr.↗
NASA NTRS1986

Recent developments in materials and detectors for the infrared; Proceedings of the Meeting, Cannes, France, November 25, 26, 1985

The present conference on advancements in IR-sensitive materials and detector technologies employing them gives attention to thermal detectors, focal plane array processing detectors, novel detector designs, general properties of IR optics materials, and preparation methods for such materials. Specific topics encompass the fabrication of InSb MIS structures prepared by photochemical vapor deposition, IR heterodyne detectors employing cadmium mercury telluride, low microphony pyroelectric arrays, IR detection based on minority carrier extrusion, longwave reststrahl in IR crystals, and molecular beam techniques for optical thin film fabrication.

Morten, F. D.↗
NASA NTRS1989

Mechanical alloying, characterization and consolidation of Ti-Al-Ni alloys

Mechanical alloying is being investigated as a processing route for the production of aluminide intermetallics. This program involves powder production and characterization, consolidation and thermal treatments and determination of microstructure-property relationships. An attritor mill is being used to produce powder in lots up to 1000 grams and the processing parameters are being systematically varied to establish the optimum milling conditions. The mill is being instrumented to generate data related to the processing to provide a basis for theoretical modeling. Powder is being characterized using thermal analysis, optical and electron microscopy and X-ray diffraction. Particle size distributions and powder density are being determined. Consolidation of the powder is being approached in several different ways including, cold isostatic pressing, sintering, extrusion and hot pressing. The results of the program so far will be presented and future directions discussed.

Nash, P.↗
NASA NTRS1991

Elevated temperature cracking of RSP aluminum alloy 8009 - Characterization of the environmental influence

Degradation of the material properties of the Al alloy is examined to determine the effects of moist air and predissolved hydrogen on elevated-temperature fatigue and fracture resistance. Experiments are conducted at 175 C in both moist air and high vacuum with as-processed specimens and specimens that are vacuum-heat-treated. Fracture mechanics characterizations are made for initiation and propagation fracture toughnesses during rising load, fatigue-crack propagation kinetics, and sustained-load crack-growth rates. Time-dependent embrittlement at intermediate temperatures is identified in both plate and extrusion samples of the Al-Fe-Si-V alloy 8009. Intermediate temperature cracking is found to be the same for each case in both vacuum and moist air, and the vacuum heat treatment does not significantly affect the results.

Porr, William C., Jr.↗
NASA NTRS1981

Forming electrical interconnections through semiconductor wafers

An information processing system based on CMOS/SOS technology is being developed by NASA to process digital image data collected by satellites. An array of holes is laser drilled in a semiconductor wafer, and a conductor is formed in the holes to fabricate electrical interconnections through the wafers. Six techniques are used to form conductors in the silicon-on-sapphire (SOS) wafers, including capillary wetting, wedge extrusion, wire intersection, electroless plating, electroforming, double-sided sputtering and through-hole electroplating. The respective strengths and weaknesses of these techniques are discussed and compared, with double-sided sputtering and the through-hole plating method achieving best results. In addition, hollow conductors provided by the technique are available for solder refill, providing a natural way of forming an electrically connected stack of SOS wafers.

Anthony, T. R.↗
NASA NTRS2000

NASA Out-of-Autoclave Process Technology Development

Polymer matrix composites (PMCS) will play a significant role in the construction of large reusable launch vehicles (RLVs), mankind's future major access to low earth orbit and the international space station. PMCs are lightweight and offer attractive economies of scale and automated fabrication methodology. Fabrication of large RLV structures will require non-autoclave methods which have yet to be matured including (1) thermoplastic forming: heated head robotic tape placement, sheet extrusion, pultrusion, molding and forming; (2) electron beam curing: bulk and ply-by-ply automated placement; (3) RTM and VARTM. Research sponsored by NASA in industrial and NASA laboratories on automated placement techniques involving the first 2 categories will be presented.

Johnston, Norman, J.↗
NASA NTRS1975

Relative cooling rates of mare basalts at the Apollo 12 and 15 sites as estimated from pyroxene exsolution data

X-ray single-crystal diffraction studies, supplemented by electron microprobe analyses of core pigeonites and rim augites from rocks 12031, 15085, 15475, and 15495, have been used to suggest cooling rates for these and other Apollo 12 and 15 rocks studied by similar methods. The extent of subsolidus phase separation of pyroxenes is used as a measure of the cooling rate. The results were interpreted in terms of model cooling histories of a lava flow whose thickness was estimated from the absolute cooling rates obtained by cooling rate experiments and by temperature-time variation through an extrusive flow computed by employing simplified theory of Jaeger. All available data on the exsolution and cation distributions of pyroxenes from Apollo 12 and 15 samples at present are consistent with the hypothesis that these rocks were derived from the top and interior of lava flows with thicknesses of 4-10 m. A process for exsolution of augite from a host pigeonite on (100) has been related to its low-calcium content.

Takeda, H.↗
NASA NTRS1984

Two lunar global asymmetries

The Moon's center of mass is displaced from its center of figure about 2 km in a roughly earthward direction. Most maria are on the side of the Moon which faces the Earth. It is assumed that the Moon was initially spherically symmetric. The emplacement of mare basalts transfers mass which produces most of the observed center of mass displacement toward the Earth. The cause of the asymmetric distribution of lunar maria was examined. The Moon is in a spin orbit coupled relationship with the Earth and the effect of the Earth's gravity on the Moon is asymmetric. The earth-facing side of the Moon is a gravitational favored location for the extrusion of mare basalt magma in the same way that the topographically lower floor of a large impact basin is a gravitationally favored location. This asymmetric effect increases inversely with the fourth power of the Earth Moon distance. The history of the Earth-Moon system includes: formation of the Moon by accretion processes in a heliocentric orbit ner that of the Earth; a gravitational encounter with the Earth about 4 billion years ago resulting in capture of the Moon into a geocentric orbit and heating of the Moon through dissipation of energy related to tides raised during close approaches to the Earth(5) to produce mare basalt magma; and evolution of the Moon's orbit to its present position, slowly at first to accommodate more than 500 million years during which magmas were extruded.

Hartung, J. B.↗