Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “EXPERIMENTAL REACTORS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Deuterium retention characteristics in Li film by coating and during flowing liquid Li limiter operation in experimental advanced superconducting tokamak

Lithium (Li) is a promising low-Z material for particle recycling and impurity control to improve plasma performance in fusion devices. In the experimental advanced superconducting tokamak (EAST), Li coating has become a routine method for wall conditioning, and a flowing liquid Li (FLiLi) limiter has been successfully tested several times. Deuterium retention characteristics in the Li film coated on the international thermonuclear experimental reactor-like tungsten divertor and FLiLi during plasma discharges, which is important for the utilization of Li in future fusion devices, were investigated in EAST. It is found that the absorption of the fuel particles by Li coatings decreases gradually, and recycling gradually increases over a series of discharges. The maximum net amount of deuterium retained reached ~0.8 g, corresponding to 12% deuterium in the Li. Furthermore, this corresponds to a whole day's worth of shots with a total of 87 plasma discharges and a total of ~640s plasma time after 11.75 g Li was deposited. Compared to the Li coating, it is shown that FLiLi continuously traps fuel particles and achieves a higher deuterium retention ratio over both the short- and long-term, leading to lower recycling. Meanwhile, it is also observed that the fuel particle retention ratio increases when FLiLi is closer to the plasma. This result is likely due to higher plasma heating power and limiter temperature, which cause an increased Li efflux from FLiLi due to a higher limiter temperature, which then redeposits on the other plasma-facing surfaces and increases fuel particle absorption. It is estimated that ≥ 80% of the retained D particles are captured by the continual renewal of the Li redeposition film during the FLiLi operation. This investigation would also be useful for D/T retention in future fusion devices if Li is used as a plasma-facing component.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Nuclide inventory characterization of EBR-II MOX fuel test pins

Characterization of 3 mixed oxide (MOX) fuel pins from the Experimental Breeder Reactor II (EBR-II) SPA-2/-2B experiment program was performed in support of the Advanced Reactor Experiments for Sodium Fast Reactor Fuels (ARES) joint project between Idaho National Laboratory (INL) and the Japan Atomic Energy Agency (JAEA). The characterization efforts were performed to enable transient testing in the Transient Reactor Test (TREAT) facility at INL and will include post irradiation examination (PIE) and other analyses. MOX fuel pins UW02009, 02011, and 06024 were historically irradiated from 1989 to 1994 for a total of 822.42 effective full power days (EFPDs) and peak burnup of approximately 14.3 at.% (atomic percent of heavy metal atoms, ∼134.4 GWd/t). They had since been placed in storage until a future use was identified. Characterization of the fission products and activation of each fuel pin was necessary to enable removal from storage and subsequent irradiation testing or PIE activities. The initial fuel pin geometry and composition were established using historical documentation. Irradiation history details were utilized to compute irradiated and decayed fuel pin masses, atomic densities, and activities. A pellet-wise axial neutron flux was also computed to assist in evaluation of the axial distribution of {sup 235}U and {sup 239}Pu, per pellet, within each of the test fuel pins. The results computed herein supported experiment design for advanced high-burnup MOX fuel designs under slow transient overpower (MOXTOP) conditions, which was Phase I of the ARES project. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2022

Simulation of CEFR neutronic start-up tests with FENNECS

This paper presents simulation results of selected Neutronic Start-up Tests of the China Experimental Fast Reactor (CEFR) obtained by the neutronics code FENNECS that have been performed within the frame of the IAEA Coordinated Research Program I31032. The Finite Element Neutronics code FENNECS is developed at GRS and solves the few-group steady-state and transient diffusion equation using a Galerkin-based finite element approach. Its main purpose is the safety assessment of Small Modular Reactors and Micro Reactors with complex geometry (e.g., rotating control drums) which gain increased interest internationally. Serpent has been applied to create reference models of the CEFR and cross-section libraries in 10 energy groups for FENNECS. Using these libraries, the following experiments have been simulated with FENNECS: net criticality, control rod integral and differential worth, void reactivity effect, subassembly exchange reactivity effects and reaction rate distribution. The obtained satisfactory agreements with the measurements represent a valuable contribution to the validation of FENNECS. (author)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2025

Material Characterization Report of EBR II Mark IV Fuel Element

The focus of this report is the characterization of an unirradiated as-built fuel element from the Experimental Breeder Reactor II (EBR-II) Mark IV driver fuel design. The fuel in this element is a metallic uranium-zirconium alloy, and the cladding material is HT9 stainless steel. Both the metallic fuel and cladding materials are characterized, including chemical composition, grain size, morphology, phase composition, precipitate composition, crystallography, density, and hardness.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

ATOMIC AND MICROSTRUCTURAL ORIGINS OF STORED ENERGY RELEASE IN NEUTRON-IRRADIATED SILICON CARBIDE

Here, we employ a combination of advanced synchrotron-based scattering characterization techniques to understand and unravel the atomic origins of the colossal stored energy release in neutron irradiated silicon carbide. The quantification of the neutron irradiation-induced defects, and their impact on the structureproperty relationship is important for the design and safe operation of advanced fission and fusion reactors. Our experimental results show that the atomic structure in the as irradiated samples is significantly perturbed due to a large fraction of vacancy and interstitial type defects that lead to complex microstructures and additional components in the x-ray diffraction and pair distribution function results. We directly correlate the stored energy release to the recovery of the sub-lattices, with pair distribution function analysis highlighting that the carbon interstitial and vacancy-type defects contribute to stored energy more than those of silicon. We find these results to be striking and believe our discoveries to be timely and noteworthy given the technological importance of silicon carbide to the nuclear fission and fusion communities.

Sprouster, D.J.↗
DOE OSTI2023

Evaluation of Irradiation Creep Effects in HT9 Cladding for FAST Experiments

The push for advanced reactor fuels for improved reactor safety and efficiency had led to a renewed interest in metallic fuel for nuclear reactor applications. Experimental investigation is necessary to ensure a robust understanding of the thermomechanical properties of new metallic fuel designs. Unfortunately, with the current experimental facilities, thoroughly investigating the responses of metallic fuel burnup would take a prohibitively long time. To alleviate this, the Fission Accelerated Steady State Test (FAST) was developed to accelerate the irradiation testing while simultaneously decreasing the sensitivity to fabrication tolerances by reducing the fuel diameter and scaling the experiment. This method successfully scales the radiation effects on the fuel, but the HT9 cladding is not exposed to prototypic radiation conditions. This raises questions on whether the FAST experiment results are truly indicative of the HT9 cladding performance due to radiation induced creep effects not being appropriately accounted for. Using BISON fuel performance code, the simulated FAST cladding strain is compared to simulated EBR-II cladding strain. This is done through a sensitivity study of input parameters and scaling of neutron fluence on the cladding. This allows a parametric comparison of physical phenomena on the effective difference between cladding strains between FAST and equivalent burnup EBR-II fuel pins. The results show that the irradiation induced deformation (creep or swelling) is insignificant compared to the thermal-mechanical deformation. Therefore, the difference between the FAST experiment cladding and the EBR-II experiment cladding is negligible and comparison of fuel system performance between the two experiments is appropriate.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

The Use of Long-wave Infrared Cameras for Hazardous Waste Remediation - 20457

For over fifty years, infrared cameras have been used in military applications, nondestructive testing, condition monitoring, and predictive maintenance. As infrared cameras continue to become more sophisticated and less expensive, they are providing value in an ever-increasing variety of unique applications, including hazardous waste remediation. This paper describes several instances of how infrared cameras have been used within the US Department of Defense and the US Department of Energy in support of waste remediation projects, including the author's recent use of an infrared camera in support of the Calcine Retrieval Project at the Idaho National Laboratory. Infrared cameras provide images of infrared radiation, or heat energy, which is otherwise invisible to the unaided eye. Infrared radiation is part of the electromagnetic spectrum, which includes visible light. But unlike visible light, infrared has wavelengths longer than the human eye can detect. Infrared is emitted by everything with a temperature above absolute zero (-273 deg. C, or -459 deg. F); the higher the temperature, the greater the infrared thermal radiation, or heat, that is emitted. Even objects that feel cold to us, like ice, emit thermal radiation and can be imaged by infrared cameras. These cameras are typically used to look for abnormally hot or cold spots on a component or target area under normal operating conditions. The method provides a rapid, wide-area, noncontact technique for identifying problems associated with a temperature differential. All infrared cameras can provide qualitative thermal information by displaying relative differences in temperatures within a two-dimensional image. More expensive infrared cameras can also provide quantitative information where an absolute temperature value is assigned to each pixel associated with the displayed two-dimensional image. Proper camera calibration and a solid understanding of heat transfer and thermography techniques are required when using an infrared camera to obtain quantitative information. Case studies outlined in this paper include the rapid, non-intrusive detection of hazardous decontamination solution within one-ton shipping containers at Pine Bluff Arsenal, the non-intrusive identification of residual elemental sodium within the cooling loops of the Experimental Breeder Reactor II (EBR-II) reactor at the Idaho National Laboratory, process monitoring of heat exchanger melt-and-drain efforts during EBR-II decommissioning, and the remote detection of internal steel supports within calcine storage bins prior to bin penetration. For each use of thermography, the author describes a summary of the waste remediation effort, the infrared camera used, the thermal imaging technique employed, and the results obtained. The paper concludes with a discussion on common mistakes to avoid for similar applications of thermography. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Recent Metallic Fuel Data Recovery in FIPD

The Metallic Fuels Irradiation and Physics Database (FIPD) [1] is an organized collection of metallic fuel test pin data (U-xPu-yZr, = 0 ~ 28; y = 2 ~ 10) and documentation available to industry. FIPD mainly contains three types of data: (1) Fuel pin fabrication data, including fuel slug diameter, fuel slug length, cladding diameter, smear density, etc. (2) Fuel pin operation conditions, including axial distributions for power, temperatures, fluences, burnup, and isotopic densities, etc. and (3) Fuel pin post-irradiation examination (PIE) data, including fission gas release and gas chemistry, profilometry, and neutron radiography, etc. The operating conditions for pins with PIE data available in FIPD span significant ranges across key parameters. The fuel peak burnup extends from less than 5% up to 20 at%. The cladding peak temperature varies from about 490°C to 660°C. Finally, the cladding peak DPA shows a wide range from less than 5 to 120. These broad ranges reflect the diverse testing conditions and operational parameters captured in the available PIE data. More detail about FIPD can be found in ref. [2]. The database development is an ongoing effort covering metallic fuel experiments from the Experimental Breeder Reactor II (EBR-II) and the Fast Flux Test Facility (FFTF). As reported in the ref. [3, 4], most of the PIE data generated during the IFR program [5] has been collected, reviewed, processed, and integrated into FIPD. The most recently added PIE data can be found in ref. [4], which shows the collection of over 95% of the PIE data by the time of this paper. The recent improvements to the database are summarized in this paper.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Plasma-Coupled Flow Reactor Studies of Low-Temperature Plasma Assisted Kinetics of Methanol Blended with CO2

Ignition technologies based on low-temperature plasmas (LTP) have the potential to operate next generation engines at elevated pressures and increased dilution limits promoting higher efficiencies. From a practical standpoint, research on LTP igniters has shown to enhance combustion and ignition, improve flame stability, and extend the dilution limits of combustion. All of the aforementioned gains are complemented with higher ignition efficiencies. However, the biggest challenge with incorporating this technology into engines is the knowledge gap of how exactly plasma chemistry effects can enhance the basic combustion phenomena. This coupled with the lack of validated kinetic mechanisms for plasma-combustion chemistry is the biggest obstruction to recognize efficient ignition, especially for application relevant fuels and biofuels. In order to comprehensively evaluate the effects of LTP on an oxygenated fuel specific system, this present study examines the kinetics of methanol plasma-assisted pyrolysis and oxidation using a custom-built plasma flow reactor (PFR). Experimental regimes are also further extended to understand the effects of adding CO2 to the mixture and its consequence on reaction kinetics. The PFR is installed with a dielectric-barrier discharge (DBD) configuration to induce LTP into the fuel mixture. Non-equilibrium plasmas are generated by high-voltage pulses (nearing 20 KV) administered by a plasma pulser at high-pulse repetition rates (up to 10 kHz). In order to better understand and isolate plasma chemistry and its effect on neutral chemistry, the experiments were carried out by heavily diluting reactive mixtures in nitrogen at near isothermal conditions. This suppresses the effect of exothermic reactions on chemistry allowing stable intermediates and products to be detected and quantified using ex-situ GC/MS diagnostic methods. Experiments were carried out at 0.5 atm pressure and over a wide range of temperatures from 523 K to 1203 K. Experimental results depicted the enhancement in intermediates production as well as overall lower temperatures required for complete fuel consumption in the plasma specific cases as opposed to their pure thermal counterpart. Formation of oxygenated and nitrile compounds specific to plasma assisted pyrolysis cases illustrated the efficacy of LTP to introduce new reaction pathways accelerating fuel decomposition. Increase in reactivity at lower temperatures is sought to be an effect induced by plasma chemistry postulating the acceleration in intermediates production. The onset of thermal ignition in plasma assisted oxidation is seen 200 K earlier than thermal oxidation highlighting efficient fuel conversion to final byproducts. Enhanced collisional processes afforded by LTP is seen to perturb reaction pathways between oxygenated fuel radicals and N-atoms to alter overall chemical reactivity. New insights into kinetics are gained from this study highlighting governing plasma assisted combustion (PAC) pathways for oxygenated fuel reaction chemistry. The results from this study can be used to develop future mechanisms specific to plasma chemistry which can bridge the mechanistic knowledge gap for LTP ignition so that future engines can adopt LTPs in their design for efficient combustion.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2024

Shielding an Infrasound Sensor for INL’s Fuel Conditioning Facility

Idaho National Laboratory (INL) has been pyroprocessing spent fuel from the Experimental Breeder Reactor II (EBR-II). This process occurs in the Fuel Conditioning Facility (FCF) which houses the treatment of DOE-owned sodium-bonded metal fuel. The electrometallurgical methods used in FCF treat the spent fuel from EBR-II for recycling of the uranium. The radiation field present inside FCF throughout the pyroprocessing stages affects any electronic sensors and devices that may be used for research. An example of such device is a seismoacoustic sensor which detects sound and vibration waves from the equipment in the facility. Seismoacoustic sensors are of interest to research nonproliferation techniques.

46 - INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AN↗
DOE OSTI2020

An Experimental Study of Design and Performance for the Water-Based Reactor Cavity Cooling System

The document summarizes the test activity conducted at the Texas A&M University water-cooled Reactor Cavity Cooling System experimental facility. Flow and temperature characterization of the risers' panel is conducted using advanced measurement techniques. Steady-state and transient scenarios are studied, analyzed, and discussed in the report. The experimental work is complemented with modeling and simulations using system level codes.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2025

The molten salt tritium transport experiment: A pumped fluoride salt loop for hydrogen isotope experimentation

Molten salt reactors (MSRs) and fusion reactors propose to use molten salts as coolants and breeder blanket materials, respectively. Tritium, however, poses safety concerns in both reactor types due to its ability to permeate through reactor materials and potential for environmental release. This manuscript addresses the tritium transport phenomena in molten salts and presents the design and analysis of the Molten Salt Tritium Transport Experiment (MSTTE). MSTTE is a forced-convection fluoride salt loop intended to measure hydrogen isotope permeation through structural materials in a flowing salt system. In the first phase, MSTTE will use FLiNaK salt and deuterium as surrogates for FLiBe and tritium, with future plans to utilize tritium and FLiBe. MSTTE couples a Copenhagen Atomics pumped salt loop with an external test section that introduces hydrogen isotopes into the loop and measures transport phenomena. The Hydrogen Injection System (HIS) controls hydrogen isotope introduction into the molten salt loop. Here, the permeation test section measures the permeation rate through stainless steel tubing in contact with flowing salt. Computational fluid dynamics (CFD) analysis ensures fully developed salt flow in the permeation test section. MSTTE is modeled with MELCOR-TMAP to predict the permeation rate as a function of experimental variables such as source term, salt flow rate, and salt temperature. Results indicate that the source term is the only parameter with a significant effect on the permeation rate. Pressure drop analysis suggests that the loop should operate below 200 LPM to maintain a pressure drop below 200 kPa. Additionally, finite-element analysis assesses thermal stress during loop operation to ensure the experiment's safe design. MSTTE will provide semi-integral data on tritium transport phenomena in molten salts and serve as a testbed for advancing molten salt technology.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Experimental and theoretical investigations of rotating algae biofilm reactors (RABRs): Areal productivity, nutrient recovery, and energy efficiency

Microalgae biofilms have been demonstrated to recover nutrients from wastewater and serve as biomass feedstock for bioproducts. However, there is a need to develop a platform to quantitatively describe microalgae biofilm production, which can provide guidance and insights for improving biomass areal productivity and nutrient uptake efficiency. Here, this paper proposes a unified experimental and theoretical framework to investigate algae biofilm growth on a rotating algae biofilm reactor (RABR). Experimental laboratory setups are used to conduct controlled experiments on testing environmental and operational factors for RABRs. We propose a differential–integral equation‐based mathematical model for microalgae biofilm cultivation guided by laboratory experimental findings. The predictive mathematical model development is coordinated with laboratory experiments of biofilm areal productivity associated with ammonia and inorganic phosphorus uptake by RABRs. The unified experimental and theoretical tool is used to investigate the effects of RABR rotating velocity, duty cycle (DC), and light intensity on algae biofilm growth, areal productivity, nutrient uptake efficiency, and energy efficiency in wastewater treatment. Our framework indicates that maintaining a reasonable light intensity range improves biomass areal productivity and nutrient uptake efficiency. Our framework also indicates that faster RABR rotation benefits biomass areal productivity. However, maximizing the nutrient uptake efficiency requires a reasonably low RABR rotating speed. Energy efficiency is strongly correlated with RABR rotating speed and DC.

09 BIOMASS FUELS↗
DOE OSTI2022

Fabricating Fuel for the Versatile Test Reactor

A metal driver fuel has been proposed for the Versatile Test Reactor (VTR). About 30 years ago, the Experimental Breeder Reactor-II (EBR-II) was the last reactor in the U.S. to utilize a full core of metal driver fuel. While the necessary knowledge to make metal fuels is well preserved and is practiced for research activities today, re-establishing a production line to support the fuel needs of a 300 MWth reactor has unique technical and engineering challenges. These challenges are the focus of a multi-laboratory and private sector team that has been tasked with the responsibility to fabricate fuel for the VTR.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Nondestructive measurements of residual 235 U mass of Israeli Research Reactor-1 fuel using the Advanced Experimental Fuel Counter

In 2018, a measurement campaign took place with participants from Los Alamos National Laboratory (LANL), the Nuclear Research Centre-Negev (NRCN) and Soreq Nuclear Research Center (SNRC) at the Israeli Research Reactor-1 (IRR-1) in which 14 of the reactor’s used fuel assemblies (FAs) with varied amount of depletion were measured with the nondestructive assay instrument Advanced Experimental Fuel Counter (AEFC). Designed for safeguards purposes, the AEFC measures both neutrons emitted from the FA (passive neutrons) and fission neutrons induced by an external neutron source (in this experiment, 252 Cf). Signals recorded with the AEFC include total neutron count rates (Singles), time-correlated neutron count rates (Doubles), and total gamma-ray count rates. The 235 U content of the FAs was previously assessed by two independent methods: (1) measurement of the transparency of the FA to low-energy gamma rays from an activated rhenium source (rhenium gamma transmission, or the RGT method) and (2) calculation of the 30-year burnup history of the core using detailed three-dimensional Monte-Carlo core depletion calculations. The results from the FAs that had been measured via the RGT method were used to construct the calibration curves, which translate the AEFC count rates to 235 U mass. Then, the calibration was evaluated using AEFC measurements of six additional FAs that were not measured via the RGT method. From the results, it was determined the Doubles calibration curve was more reliable than that of the Singles and follows a simple second-order polynomial fit for the whole range of residual 235 U mass content, albeit with larger statistical uncertainty. Detailed uncertainties quantification was conducted for both the AEFC Singles and Doubles. This includes the analysis of statistical uncertainties, calibration uncertainty, and random uncertainties due to the sensitivity of the AEFC to several sources of uncertainty, namely the FA position, FA orientation, interrogation source position, and ambient pool temperature. Finally, an overall total uncertainty of 6 g of 235 U is estimated for the Singles and Doubles, which is mainly due to calibration uncertainty (for the Singles) and statistical uncertainty (for the Doubles), and which constitutes 3%–6% of the 235 U total mass in the FAs, depending on their level of depletion.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2022

Does a visit to EBR-I improve perceptions of nuclear power?

The advancement of nuclear research depends not only on the improvements made by scientists and engineers, but also on public approval in the United States. Presently, the public is not just curious about new applications of nuclear power but also concerned about the potential impact on their own safety and environment. It is projected that nuclear power production in the U.S. will decline due to industry stagnation. The skepticism of nuclear energy has remained high for decades. These attitudes need to be understood by policymakers, industry, and advocates given the electricity needs, competition, and climate change. The Experimental Breeder Reactor-I is the world’s first nuclear reactor to produce usable electricity. It has been a museum since 1975 and sees an average of 10,000 visitors every summer. I set out to gauge the opinion of visitors as they tour the facility. In this research project, I conduct a public opinion poll (n=162) over the course of a week to see if a visit to EBR-I improves the perception of nuclear power. The results suggest that a visit to EBR-I increased perceptions of nuclear power in a positive direction.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2025

Effects of break geometry and orientation on helium-air mixing in simulated reactor cavities of high temperature gas reactors

Here, this study experimentally examined the spatial and temporal variations in air and helium concentrations and temperature fields within simulated reactor cavities of a High Temperature Gas Reactor (HTGR) following helium discharge into an initially air-filled reactor cavity system. Detailed temperature maps were generated using a combination of fiber optics temperature sensor and multiple thermocouple probes within the simulated reactor cavities. The research scenario involved a hypothetical small pipe break in the Reactor Pressure Vessel, resulting in the release of high-temperature helium into the surrounding cavity. A scaled multi-compartment experimental facility, modeled after the General Atomics Modular High Temperature Gas Reactor (GA-MHTGR) design, was constructed for helium and air mixing experiments. Oxygen sensors and thermocouple probes were installed in all five cavities to measure the concentrations of oxygen (or helium) and the temperature distributions of the gas mixture. The experimental findings highlighted the significant impact of the injected helium jet velocity on the gas mixing process and demonstrated how the direction of the helium jet influences the air-helium temperature profiles within the cavities.

Air-ingress↗