Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “EGR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Total Cost of Ownership Reduction Using Passive Pre-Chamber Ignition in Natural Gas Engines

Spark plug durability is a factor affecting the total cost of ownership (TCO) of spark-ignited natural gas engines, with some heavy-duty platforms requiring plug replacement after only 750 hours of operation. The high ignition energy demand under lean or diluted conditions accelerates electrode wear, shortening plug life and increasing maintenance frequency. This work evaluates passive pre-chamber (PC) ignition operating at lowered spark energies as a strategy to reduce spark energy requirements and extend plug durability, thereby lowering TCO. Experiments were conducted on a medium-duty Cummins 6.7L ISB engine at 1600 RPM and 50% load under varying exhaust gas recirculation (EGR) dilution levels (0–40%). Two passive pre-chambers with 1.1 mm and 1.6 mm nozzle diameters were compared with conventional spark ignition (SI). SI was operated with a fixed coil dwell of 4 ms (~90 mJ), while the PC configuration was tested across 2–4 ms dwell times (~30–90 mJ). Cylinder pressure analysis revealed that PC ignition sustained stable combustion at significantly lower spark energies than SI, with improved combustion stability at ~30 mJ compared with SI at ~90 mJ. The PC system also extended the dilution tolerance beyond that achievable with SI, while delivering up to ~2% higher indicated thermal efficiency and reducing the COV by nearly 90% at 30% EGR. A TCO analysis was conducted to assess the economic benefit of adopting a passive PC system operating at reduced spark energies compared to SI. It was found that adopting a passive PC system could reduce TCO by approximately $11,000 per engine over a five-year operational period, primarily due to fuel savings, extended spark plug life, and reduced maintenance frequency. These projections were weighed against the additional hardware cost of the pre-chamber, yielding a rapid estimated return on investment of ~300 operating hours. Therefore, this work motivates continued research and development of passive PC technology and its commercial adoption in natural gas engines used in transportation applications.

Dhotre, Akash [University of Minnesota]↗
NASA NTRS1983

An analytical investigation of NO sub x control techniques for methanol fueled spark ignition engines

A thermokinetic SI engine simulation was used to study the effects of simple nitrogen oxide control techniques on performance and emissions of a methanol fueled engine. As part of this simulation, a ring crevice storage model was formulated to predict UBF emissions. The study included spark retard, two methods of compression ratio increase and EGR. The study concludes that use of EGR in high turbulence, high compression engines will both maximize power and thermal efficiency while minimizing harmful exhaust pollutants.

Browning, L. H.↗
NASA NTRS1998

A Modified Through-Flow Wave Rotor Cycle with Combustor Bypass Ducts

A wave rotor cycle is described which avoids the inherent problem of combustor exhaust gas recirculation (EGR) found in four-port, through-flow wave rotor cycles currently under consideration for topping gas turbine engines. The recirculated hot gas is eliminated by the judicious placement of a bypass duct which transfers gas from one end of the rotor to the other. The resulting cycle, when analyzed numerically, yields an absolute mean rotor temperature 18% below the already impressive value of the conventional four-port cycle (approximately the turbine inlet temperature). The absolute temperature of the gas leading to the combustor is also reduced from the conventional four-port design by 22%. The overall design point pressure ratio of this new bypass cycle is approximately the same as the conventional four-port cycle. This paper will describe the EGR problem and the bypass cycle solution including relevant wave diagrams. Performance estimates of design and off-design operation of a specific wave rotor will be presented. The results were obtained using a one-dimensional numerical simulation and design code.

Paxson Daniel E.↗
DOE OSTI2011

Effect of Heat Exchanger Material and Fouling on Thermoelectric Exhaust Heat Recovery

This study is conducted in an effort to better understand and improve the performance of thermoelectric heat recovery systems for automotive use. For this purpose an experimental investigation of thermoelectrics in contact with clean and fouled heat exchangers of different materials is performed. The thermoelectric devices are tested on a bench-scale thermoelectric heat recovery apparatus that simulates automotive exhaust. The thermoelectric apparatus consists of a series of thermoelectric generators contacting a hot-side and a cold-side heat exchanger. The thermoelectric devices are tested with two different hot-side heat exchanger materials, stainless steel and aluminum, and at a range of simulated exhaust gas flowrates (40 to 150 slpm), exhaust gas temperatures (240 C and 280 C), and coolant-side temperatures (40 C and 80 C). It is observed that for higher exhaust gas flowrates, thermoelectric power output increases while overall system efficiency decreases. Degradation of the effectiveness of the EGR-type heat exchangers over a period of driving is also simulated by exposing the heat exchangers to diesel engine exhaust under thermophoretic conditions to form a deposit layer. For the fouled EGR-type heat exchangers, power output and system efficiency is observed to be significantly lower for all conditions tested. The study found, however, that heat exchanger material is the dominant factor in the ability of the system to convert heat to electricity with thermoelectric generators. This finding is thought to be unique to the heat exchangers used for this study, and not a universal trend for all system configurations.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2012

Effect of E85 on RCCI Performance and Emissions on a Multi-Cylinder Light-Duty Diesel Engine - SAE World Congress

This paper investigates the effect of E85 on load expansion and FTP modal point emissions indices under reactivity controlled compression ignition (RCCI) operation on a light-duty multi-cylinder diesel engine. A General Motors (GM) 1.9L four-cylinder diesel engine with the stock compression ratio of 17.5:1, common rail diesel injection system, high-pressure exhaust gas recirculation (EGR) system and variable geometry turbocharger was modified to allow for port fuel injection with gasoline or E85. Controlling the fuel reactivity in-cylinder by the adjustment of the ratio of premixed low-reactivity fuel (gasoline or E85) to direct injected high reactivity fuel (diesel fuel) has been shown to extend the operating range of high-efficiency clean combustion (HECC) compared to the use of a single fuel alone as in homogeneous charge compression ignition (HCCI) or premixed charge compression ignition (PCCI). The effect of E85 on the Ad-hoc federal test procedure (FTP) modal points is explored along with the effect of load expansion through the light-duty diesel speed operating range. The Ad-hoc FTP modal points of 1500 rpm, 1.0bar brake mean effective pressure (BMEP); 1500rpm, 2.6bar BMEP; 2000rpm, 2.0bar BMEP; 2300rpm, 4.2bar BMEP; and 2600rpm, 8.8bar BMEP were explored. Previous results with 96 RON unleaded test gasoline (UTG-96) and ultra-low sulfur diesel (ULSD) showed that with stock hardware, the 2600rpm, 8.8bar BMEP modal point was not obtainable due to excessive cylinder pressure rise rate and unstable combustion both with and without the use of EGR. Brake thermal efficiency and emissions performance of RCCI operation with E85 and ULSD is explored and compared against conventional diesel combustion (CDC) and RCCI operation with UTG 96 and ULSD.

02 PETROLEUM↗
DOE OSTI2014

Power plant including an exhaust gas recirculation system for injecting recirculated exhaust gases in the fuel and compressed air of a gas turbine engine

A power plant is provided and includes a gas turbine engine having a combustor in which compressed gas and fuel are mixed and combusted, first and second supply lines respectively coupled to the combustor and respectively configured to supply the compressed gas and the fuel to the combustor and an exhaust gas recirculation (EGR) system to re-circulate exhaust gas produced by the gas turbine engine toward the combustor. The EGR system is coupled to the first and second supply lines and configured to combine first and second portions of the re-circulated exhaust gas with the compressed gas and the fuel at the first and second supply lines, respectively.

42 ENGINEERING↗
DOE OSTI2015

Rankine cycle waste heat recovery system

A waste heat recovery (WHR) system connects a working fluid to fluid passages formed in an engine block and/or a cylinder head of an internal combustion engine, forming an engine heat exchanger. The fluid passages are formed near high temperature areas of the engine, subjecting the working fluid to sufficient heat energy to vaporize the working fluid while the working fluid advantageously cools the engine block and/or cylinder head, improving fuel efficiency. The location of the engine heat exchanger downstream from an EGR boiler and upstream from an exhaust heat exchanger provides an optimal position of the engine heat exchanger with respect to the thermodynamic cycle of the WHR system, giving priority to cooling of EGR gas. The configuration of valves in the WHR system provides the ability to select a plurality of parallel flow paths for optimal operation.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2015

Effects of Ignition and Injection Perturbation under Lean and Dilute GDI Engine Operation

Turbocharged gasoline direct injection (GDI) engines are quickly becoming more prominent in light-duty automotive applications because of their potential improvements in efficiency and fuel economy. While EGR dilute and lean operation serve as potential pathways to further improve efficiencies and emissions in GDI engines, they also pose challenges for stable engine operation. Tests were performed on a single-cylinder research engine that is representative of current automotive-style GDI engines. Baseline cases were performed under steady-state operating conditions where combustion phasing and dilution levels were varied to determine the effects on indicated efficiency and combustion stability. Sensitivity studies were then carried out by introducing binary low-high perturbation of spark timing and injection duration on a cycle-by-cycle basis under EGR dilute and lean operation to determine dominant feedback mechanisms. Ignition perturbation was phased early/late of MBT timing, and injection perturbation was set fuel rich/lean of the given air-to-fuel ratio. COVIMEP was used to define acceptable operation limits when comparing different perturbation cases. Overall sensitivity data shows COVIMEP is more sensitive to injection perturbation over ignition perturbation. This is because of the greater effect injection perturbation has on combustion phasing, ignition delay, and combustion duration.

Wallner, Thomas↗
DOE OSTI2016

Impact of delayed spark restrike on the dynamics of cyclic variability in dilute SI combustion

Spark-ignition (SI) engines can derive substantial efficiency gains from operation at high dilution levels. Additionally, the use of exhaust gas recirculation (EGR) for charge dilution also maintains compatibility with three-way catalysts by allowing stoichiometric operation. However, running high dilution levels increases the occurrence of misfires and partial burns, which induce higher levels of cyclic-variability in engine operation. This variability has been shown to have both stochastic and deterministic components. Factors such as in-cylinder turbulence and mixing-variations can be classified as stochastic; while, charge composition is the major source of the deterministic component through its non-linear effect on ignition and flame propagation characteristics. The use of these deterministic components has been previously explored to construct next-cycle control approaches that would allow stable operation near the edge of stability. Building on that work, this paper aims to understand the effect of spark strategies, specifically the use of a second spark (restrike) after the main spark, on engine operation at high dilution levels that were achieved using both excess air (i.e. lean combustion) and EGR.

Kaul, Brian C↗
DOE OSTI2010

System for particulate matter sensor signal processing

A system having a particulate matter sensor in an exhaust stream of an engine upstream from a particulate filter and another such sensor downstream from the filter. There may also be an exhaust gas recirculation (EGR) control on the engine. The amount of particulate matter in or loading of the filter may be determined by the upstream filter. The working condition of the filter may be determined by the downstream sensor. The filter may have a heater and control for providing operational and particulate matter burn-off temperatures to the filter. A processor may be connected to the sensors, the EGR control and the filter heater control.

Rhodes, Michael L.↗
DOE OSTI2018

System and method of exhaust gas recirculation

A system includes an exhaust gas an exhaust gas recirculation (EGR) mixer which includes a housing and a first passage in the housing. The first passage may be configured to supply an EGR flow into the housing. The system further includes a second passage in the housing, such that the second passage is disposed about the first passage. The second passage is configured to supply at least one fluid flow into the housing. The system also includes a region downstream from the first and second passages, and a fluid outlet downstream from the region.

Zurlo, James Richard↗
DOE OSTI2019

Fundamental Advancements in Pre-Chamber Spark Ignition and Emissions Control for Natural Gas Engines

Argonne National Laboratory, the National Renewable Energy Laboratory, Oak Ridge National Laboratory, and Sandia National Laboratories collaborated on research to address barriers for natural gas engine efficiency. This research project focuses on early stage research focusing on pre-chamber spark-ignition (PCSI) to achieve diesel-like efficiency in medium- and heavy-duty natural gas engines by extending the lean dilution limit and/or exhaust gas recirculation (EGR) dilution limit, as well as shortening burn duration, with integrated aftertreatment. This project integrates experimental and simulation based tasks to address four key barriers to market penetration of PCSI for medium- and heavy-duty natural gas engines. These include Inadequate science base and simulation tools to describe/predict the fluid-mechanical and chemical-kinetic processes governing PCSI to enable engineers in industry to optimize designs for efficiency, noise, reliability, pollutant formation, emissions control integration, and drivability; limited ability to extend EGR and/or lean dilution limits at higher loads; increased propensity for PCSI hot-spot pre-ignition at high loads relative to spark ignition; and ineffective methane catalysts for the high engine-out unburned fuel concentrations coupled with low exhaust temperatures (<<400 degrees C) of high efficiency engines.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2019

3-D Modeling off the CFR Engine for the Investigation of Knock on Natural Gas

Engine knock and misfire are barriers to pathways leading to high-efficiency Natural Gas (NG) engines. The general tendency to knock is highly dependent on engine operating conditions and the fuel reactivity. The problem is further complicated by low emissions limits and the wide range of chemical reactivity in pipeline quality NG (65< MN<95). In order to realize diesel-like efficiencies, spark-ignited NG engines must be designed to operate at high BMEP near knock limits over a wide range of fuel reactivity. This requires a deep understanding regarding combustion-engine interactions important in flame propagation and end-gas autoignition. The present work highlights a three-dimensional computational fluid dynamics (CFD) model of the Cooperative Fuel Research (CFR) engine to investigate knock behavior with NG. The CFR engine model is used to investigate fuel-engine interactions that lead to knock with NG, including effects of fuel reactivity, engine operating parameters, and exhaust gas recirculation (EGR). Cylinder wall, piston, valves, and port surface temperatures are estimated with a 1-D Three-Pressure Analysis (TPA) model. Model validation was performed by comparing model predictions with experimental data taken with a CFR engine over varying compression ratio, CA50, EGR fraction and BMEP.

Bestel, Diego↗
DOE OSTI2020

MULTI-DIMENSIONAL MODELING OF THE CFR ENGINE FOR THE INVESTIGATION OF SI NATURAL GAS COMBUSTION AND CONTROLLED END-GAS AUTOIGNITION

Engine knock and misfire are barriers to pathways leading to high-efficiency Spark-Ignited (SI) Natural Gas engines. The general tendency to knock is highly dependent on engine operating conditions and the fuel reactivity. The problem is further complicated by low emission limits and the wide range of chemical reactivity in pipeline quality natural gas. Depending on the region and the source of the natural gas, its reactivity, described by its methane number (analogous to the octane number for liquid SI fuels) can span from 65 - 95. In order to realize diesel-like efficiencies, SI natural gas engines must be designed to operate at high BMEP near knock limits over a wide range of fuel reactivity. This requires a deep understanding regarding the combustion-engine interactions pertaining to flame propagation and end-gas autoignition (EGAI). However, EGAI, if controlled, provides an opportunity to increase SI natural gas engine efficiency by increasing combustion rate and the total burned fuel, mitigating the effects of the slow flame speeds of natural gas fuels which generally reduce BMEP and increase unburned hydrocarbon emissions. For this reason, in order to study EGAI phenomenon, the present work highlights multi-dimensional computational fluid dynamics (CFD) models of the Cooperative Fuel Research (CFR) engine. The CFR engine models are used to investigate fuel-engine interactions that lead to EGAI with natural gas, including effects of fuel reactivity, engine operating parameters, and exhaust gas recirculation (EGR). A Three-Pressure Analysis, performed with GT-Power, was used to estimate initial and boundary conditions for the three-dimensional CFD model. CONVERGE CFD v2.4 was used for the three-dimensional CFD modeling where the level set G-Equation model and SAGE detailed chemical kinetics solver were used. An assessment of the different modeling approaches is also provided to evaluate their limitations, advantages and disadvantages, and for which situations they are most applicable. Model validation was performed with experimental data taken with a CFR engine over varying compression ratio, CA50, EGR fraction, and IMEP and shows good agreement in Peak Cylinder Pressure (PCP), PCP crank angle, and the location of the 10%, 50%, and 90% mass fraction burned (CA10, CA50, and CA90, respectively). The models can predict the onset crank angle and pressure rise rate for light, medium, and heavy EGAI under a variety of fuel reactivities and engine operating conditions.

Bestel, Diego↗
DOE OSTI2020

THE EFFECT OF FUEL REACTIVITY AND EXHAUST GAS RECIRCULATION ON KNOCK PROPENSITY OF NATURAL GAS

The development of high efficiency, spark ignited natural gas engines is currently limited by engine knock at high compression ratio/elevated boost pressures and misfire at lean conditions/high exhaust gas recirculation (EGR) levels. The knock and misfire limits are further confounded by the wide variety in fuel reactivity observed in “pipeline quality” natural gas. In this study, a rapid compression machine was used to characterize the effects of EGR and variation in natural gas fuel reactivity on the homogeneous ignition delay, flame propagation rate, and end- gas autoignition propensity for stoichiometric natural gas/oxidizer/EGR blends. A reduced chemical kinetic mechanism was also developed to accurately model the homogeneous ignition delays measured in the Colorado State University rapid compression machine (CSU RCM). Pipeline quality natural gas with a range of chemical reactivity (68 < Methane Number < 95) was simulated using mixtures of CH4, C2H6, and C3H8. Exhaust gas recirculation gases were simulated with mixtures of Ar, CO2, CO, and NO at substitution rates of 0 to 30 mass percent. Ignition delay period under homogeneous autoignition conditions was measured at compressed pressures of 30.2 to 34.0 bar and compressed temperatures of 667 to 980 K. End-gas autoignition fraction and flame propagation rate were measured by initiating a laser spark in the center of the combustion chamber, after compression, at pressures of 30.7 to 32.7 bar and temperatures of 751 to 795 K. The results indicate that both fuel reactivity and the presence of reactive species (NO and CO) in the exhaust gas recirculation have a strong impact on end-gas autoignition fraction. A chemical kinetic mechanism was developed to predict homogeneous ignition delays for pipeline quality natural gas in a pressure and temperature range of 1-100 bar and 500-1000 K respectively. This mechanism accurately predicted measured homogeneous ignition delay in the RCM with a total average relative error of 11.0%.

Mohr, Jeffrey↗
DOE OSTI2021

Autoignition of Premixed Liquefied Petroleum Gas in a Rapid Compression Machine: Experimental Results and Chemical Kinetic Mechanism Reduction

Liquefied petroleum gas (LPG) has many properties that make it an attractive alternative fuel such as lower cost than conventional fuels and an established distribution infrastructure. The development of high efficiency, spark ignited LPG engines is currently limited by engine knock and misfire. The knock and misfire limits are further complicated by the wide range of chemical reactivity in LPG, particularly in international markets. In this study, a rapid compression machine (RCM) was used to characterize the effects of variation in LPG fuel reactivity, equivalence ratio, and exhaust gas recirculation (EGR) on autoignition of LPG/oxidizer/inert/EGR blends. Experiments were conducted with 100% propane (C3H8) and blends of propane with propene, ethane, isobutane, and n-butane. EGR was simulated with mixtures of Ar, CO2, CO, and NO at substitution percentages from 0 to 30 mass percent. Equivalence ratio was varied from 0.75 to 1.5. Ignition delay period under homogeneous autoignition conditions was measured at compressed pressures and temperatures of 23 to 25 bar and 701 to 921 K, respectively. Zero-dimensional simulations of the RCM experiments were performed using Chemkin with several detailed chemical kinetic mechanisms to determine their suitability at predicting ignition delay periods. Multiple reduced chemical kinetic mechanisms were created from the NUIGMech1.1 mechanism to determine the optimal balance between accuracy and computational efficiency for future three-dimensional, time-dependent spark-ignited engine computations.

42 ENGINEERING↗
DOE OSTI2023

Low soot stoichiometric compression-ignition combustion

A combustion system including a combustion mechanism that injects oxygenated fuel into a combustion chamber. The oxygenated fuel mixes with the intake air in the combustion chamber where the air-fuel ratio in a portion of the combustion chamber is stoichiometric. The combustion mechanism includes an ignition mechanism that ignites the air-fuel mixture that generates a threshold number of particulates during combustion of the air-fuel mixture. The combustion system further includes an exhaust gas recirculation (EGR) device that recirculates a portion of the exhaust gases back into the combustion chamber. The EGR device recirculates the portion of the exhaust to lower combustion temperature resulting in reduced amount of nitrogen oxide in the exhaust. The combustion system further includes a three-way catalytic converter in line with the exhaust channel to convert a second portion of the exhaust gases, leading to lower pollutant emissions than conventional combustion systems.

Pickett, Lyle M.↗
DOE OSTI2013

Exhaust Gas Recirculation Cooler Fouling in Diesel Applications: Fundamental Studies Deposit Properties and Microstructure

This paper reports on the results of experimental efforts aimed at improving the understanding of the mechanisms and conditions at play in the fouling of EGR coolers. An experimental apparatus was constructed to utilize simplified surrogate heat exchanger tubes in lieu of full-size heat exchangers. The use of these surrogate tubes allowed removal of the tubes after exposure to engine exhaust for study of the deposit layer and its properties. The exhaust used for fouling the surrogate tubes was produced using a modern medium-duty diesel engine fueled with both ultra-low sulfur diesel and biodiesel blends. At long exposure times, no significant difference in the fouling rate was observed between fuel types and HC levels. Surface coatings for the tubes were also evaluated to determine their impact on deposit growth. No surface treatment or coating produced a reduction in the fouling rate or any evidence of deposit removal. In addition, microstructural analysis of the fouling layers was performed using optical and electron microscopy in order to better understand the deposition mechanism. The experimental results are consistent with thermophoretic deposition for deposit formation, and van der Waals attraction between the deposit surface and exhaust-borne particulate.

EGR↗