Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Divertor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Double-null power-sharing dynamics in MAST-U

Maintaining an effective double-null (DN) configuration is expected to be challenging in reactor-scale tokamak devices. As divertor power-sharing is closely linked to the magnetic topology, even minor variations can lead to fast power-sharing fluctuations which exacerbate the already daunting exhaust challenge. While the static aspects of DN power-sharing have been extensively studied across various devices, this paper presents the first detailed investigation of its dynamic behaviour. We employ dedicated H-mode experiments in MAST-U, in Super-X divertor configuration, featuring perturbation frequencies up to 200 Hz. Our results clearly show no significant dynamic damping of the power-sharing within this frequency range: the divertor responds equally to both fast and slow perturbations. Moreover, the dynamic response also aligns with quasi-static results from slow ramps, implying that static power-sharing models remain valid even for fast fluctuations. Occasionally, some deviations from the otherwise mainly linear behaviour are observed, alongside notable scatter and asymmetries between upwards and downwards trajectories. These observations are likely linked to changes in core conditions, though the underlying mechanisms remain unclear and require further study.

divertor↗
DOE OSTI2025

Deuterium retention in pre-lithiated samples and Li–D co-deposits in the DIII-D tokamak

Divertor designs involving liquid lithium have been proposed as an alternative to solid designs and wall conditioning techniques. However, Li affinity with tritium poses a risk for the fuel cycle. This study investigates deuterium retention in pre-lithiated samples and Li–D co-deposits in the DIII-D tokamak, making for the first time a direct comparison between Li–D co-deposits and pre-deposited Li films. Samples were exposed to H-mode plasmas in the far scrape-off layer (SOL), and Li powder was injected in-situ with the impurity powder dropper to study the uniformity of Li coatings, and the dependence of fuel retention on Li thickness. The results show that at temperatures below the melting point of lithium, deuterium retention is independent of the thickness of pre-deposited Li layers, with Li–D co-deposits being the primary factor for fuel retention. Both pre-deposited and in-situ deposited Li showed lower erosion than predicted by sputtering yield calculations. These results suggest that fuel retention in fusion reactors using lithium in the divertor will likely be dominated by co-deposits rather than in the divertor itself. If one desires to use Li to achieve flatter temperature profiles, operando Li injection is advantageous over pre-deposited Li films, at least at temperatures below the melting point of lithium.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

First-wall fluxes from large and small ELMs

Experimental analysis at DIII-D shows that small edge localized modes (ELMs) deposit a larger fraction of their energy to the first wall, compared to type-I ELMs in similar magnetic configuration and input power. The energy (λQ) and particle (λΓ) flux decay lengths in the scrape-off layer (SOL) are up to 3 and 5 times larger, respectively, for small ELMs than for larger type-I ELMs. Transport dynamics of ELM filaments in the SOL are found to be related to divertor conditions, where high divertor collisionality, typical for partially detached plasmas, is associated with increased cross field ELM radial fluxes. Results show that a sufficiently large outer wall gap and/or limiters might be needed in future scenarios to protect the first wall, if operating with small ELMs and a cold divertor. This might also have implications for RF heating in future devices, where the coupling efficiency is dependent to some degree to the outer-wall gap.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Efficient analysis of magnetic field line behavior in toroidal plasmas

The confinement of plasmas in tokamaks and stellarators depends on magnetic field lines lying in nested toroidal surfaces. The transition near the plasma edge away from the lines lying in magnetic surfaces defines properties of divertors. The transition in time defines properties of disruptions. Divertor design and disruption analyses require a detailed understanding of these transitions. The use of a Fourier transform coupled with a Gaussian window function allows far more information to be extracted about these transitions using far shorter field line integrations than can be obtained using traditional methods based on Poincaré plots. The physics of divertors and disruptions is reviewed to clarify why the type of information that can be gained from more efficient methods of analysis is of central importance to the fusion program based on magnetic confinement.

Boozer, Allen H. [Columbia Univ., New York, NY (Un↗
DOE OSTI2025

Direct comparison of gyrokinetic and fluid scrape-off layer simulations

Typically, fluid simulations are used for tokamak divertor design. However, fluid models are only valid if the scrape-off layer (SOL) is highly collisional. This assumption is valid in many present-day experiments but is questionable in the upstream SOL of some high-power scenarios envisioned for burning plasmas and fusion pilot plants. This paper reports on comparisons between fluid and kinetic simulations of the SOL for upstream parameters and geometry representative of the Spherical Tokamak for Energy Production fusion pilot plant. The SOLPS-ITER (fluid) and Gkeyll (gyrokinetic) codes are operated in a two-dimensional axisymmetric mode, which replaces turbulence with ad-hoc diffusivities. In kinetic simulations, we observe that the ions in the upstream SOL experience significant mirror trapping. This substantially increases the upstream temperature and has important implications for impurity dynamics. We show that the mirror force, which is excluded in SOLPS’s fluid equations, enhances the electrostatic potential drop along the field line in the SOL. We also show that the assumption of equal main ion and impurity temperatures, which is made in commonly used fluid codes, is invalid for the regimes explored here. The combination of these effects results in superior confinement of impurities to the divertor region in kinetic simulations, consistent with our earlier predictions [Kotschenreuther et al., in 29th IAEA 29 Fusion Energy Conference (IAEA, London, UK, 2023)]. This effect can be dramatic, reducing the midplane impurity density by orders of magnitude. These results indicate that in lower collisionality SOL’s the tolerable downstream impurity densities may be higher than would be predicted by fluid simulations, allowing for higher radiated power while avoiding unacceptable core contamination. Our results highlight the importance of kinetic simulations for divertor design and optimization for fusion pilot plants.

Computational fluid dynamics↗
DOE OSTI2024

Overview of results from the 2023 DIII-D negative triangularity campaign

Negative triangularity (NT) is a potentially transformative configuration for tokamak-based fusion energy with its high-performance core, edge localized mode (ELM)-free edge, and low-field-side divertors that could readily scale to an integrated reactor solution. Previous NT work on the TCV and DIII-D tokamaks motivated the installation of graphite-tile armor on the low-field-side lower outer wall of DIII-D. A dedicated multiple-week experimental campaign was conducted to qualify the NT scenario for future reactors. During the DIII-D NT campaign, high confinement ($H_\mathrm{98y,2}\gtrsim$ 1), high current ($q_\mathrm{95} \lt$ 3), and high normalized pressure plasmas ($\beta_\mathrm{N} \gt$ 2.5) were simultaneously attained in strongly NT-shaped discharges with average triangularity $\delta_\mathrm{avg}$ = −0.5 that were stably controlled. Experiments covered a wide range of DIII-D operational space (plasma current, toroidal field, electron density and pressure) and did not trigger an ELM in a single discharge as long as sufficiently strong NT was maintained; in contrast, to other high-performance ELM-suppression scenarios that have narrower operating windows. These strong NT plasmas had a lower outer divertor X-point shape and maintained a non-ELMing edge with an electron temperature pedestal, exceeding that of typical L-mode plasmas. Also, the following was achieved during the campaign: high normalized density ($n_\mathrm{e}$/$n_\mathrm{GW}$ of at least 1.7), particle confinement comparable to energy confinement with $Z_\mathrm{eff}\sim2$ , a detached divertor without impurity seeding, and a mantle radiation scenario using extrinsic impurities. These results are promising for a NT fusion pilot plant but further questions on confinement extrapolation and core-edge integration remain, which motivate future NT studies on DIII-D and beyond.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Tungsten control in long pulse operation: feedback from WEST to ITER

The full W environment that is now foreseen for ITER puts strong emphasis on experimental results obtained in present devices in similar conditions. In this context, the WEST tokamak is well equipped to bring key contributions to the preparation of ITER operation, thanks to its capability to perform long pulses in dominant electron heating, torque-free scheme based on RF systems, and its ITER-grade actively cooled divertor. Recent results of interest cover the understanding of tungsten contamination and the evaluation of conditioning methods, the feedback on the current ramp-up phase, and the ageing of the ITER divertor components in L-mode attached condition. Further, new directions are being explored, in particular low divertor temperature operation that should be the normal operating regime of ITER. We also report on tungsten peaking physics, and the role of light impurity content.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Predicting core transport in ITER baseline discharges with neon injections

Achieving self-consistent performance predictions for ITER requires integrated modeling of core transport and divertor power exhaust under realistic impurity conditions. We present results from a systematic power-flow and impurity-content study for the ITER 15 MA baseline scenario constrained directly by existing SOLPS-ITER neon-seeded divertor solutions. Using the OMFIT STEP workflow, stationary temperature and density profiles are predicted with TGYRO for $1.5 \unicode{x2A7D} Z_\textrm{eff} \unicode{x2A7D} 2.5$, and the corresponding power crossing the separatrix $P_\textrm{sep}$ is evaluated. We find that $P_\textrm{sep}$ varies by more than a factor of 1.7 across this scan and matches the ${\sim}100$ MW SOLPS-ITER prediction when $Z_\textrm{eff} \simeq 1.6$ or when auxiliary heating is reduced to ${\sim}75\%$ of nominal. Rotation-sensitivity studies show that plausible variations in toroidal flow magnitude modify $P_\textrm{sep}$ by $\lesssim 20\%$, while AURORA modeling confirms that charge-exchange radiation inside the separatrix is dynamically negligible under predicted ITER neutral densities. These results identify a restricted compatibility window, $Z_\textrm{eff} \approx 1.6$ –1.75 and $0.75 \lesssim f_{P_\textrm{aux}} \unicode{x2A7D} 1.0$, in which core transport predictions remain aligned with neon-seeded divertor protection targets. This self-consistent, model-constrained framework provides actionable guidance for impurity control and auxiliary-heating scheduling in early ITER operation and supports future whole-device scenario optimization.

ITER↗
DOE OSTI2024

DIII-D research to provide solutions for ITER and fusion energy

The DIII-D tokamak has elucidated crucial physics and developed projectable solutions for ITER and fusion power plants in the key areas of core performance, boundary heat and particle transport, and integrated scenario operation, with closing the core-edge integration knowledge gap being the overarching mission. New experimental validation of high-fidelity, multi-channel, non-linear gyrokinetic turbulent transport models for ITER provides strong confidence it will achieve Q ≥ 10 operation. Experiments identify options for easing H-mode access in hydrogen, and give new insight into the isotopic dependence of transport and confinement. Analysis of 2,1 islands in unoptimized low-torque IBS demonstration discharges suggests their onset time occurs randomly in the constant β phase, most often triggered by non-linear 3-wave coupling, thus identifying an NTM seeding mechanism to avoid. Pure deuterium SPI for disruption mitigation is shown to provide favorable slow cooling, but poor core assimilation, suggesting paths for improved SPI on ITER. At the boundary, measured neutral density and ionization source fluxes are strongly poloidally asymmetric, implying a 2D treatment is needed to model pedestal fuelling. Detailed measurements of pedestal and SOL quantities and impurity charge state radiation in detached divertors has validated edge fluid modelling and new self-consistent 'pedestal-to-divertor' integrated modeling that can be used to optimize reactors. New feedback adaptive ELM control minimizes confinement reduction, and RMP ELM suppression with sustained high core performance was obtained for the first time with the outer strike point in a W-coated, compact and unpumped small-angle slot divertor. Advances have been made in integrated operational scenarios for ITER and power plants. Wide pedestal intrinsically ELM-free QH-modes are produced with more reactor-relevant conditions, Low torque IBS with W-equivalent radiators can exhibit predator-prey oscillations in Te and radiation which need control. High-β P scenarios with q min > 2, q 95 –7.9, β N > 4, β T –3.3% and H 98y2 > 1.5 are sustained with high density ($\overline{n}$ = 7E19 m -3 , f G –1) for 6 τ E , improving confidence in steady-state tokamak reactors. Diverted NT plasmas achieve high core performance with a non-ELMing edge, offering a possible highly attractive core-edge integration solution for reactors.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Impact of error fields and error field correction on heat fluxes in SPARC

Using a single toroidal array of coils to reduce the m,n = 2,1 resonant error field (EF) produced by the misalignment of the axisymmetric coils in SPARC can result in the enhancement of the local divertor heat fluxes. Managing high divertor heat fluxes (q ∥ $\simeq$ 10 GW m -2 ) poses a challenge for compact tokamak devices such as SPARC. The presence of non-axisymmetric magnetic field perturbations adds complexity to the problem by generating intricate 3D edge magnetic topologies that alter the heat flux distributions on the target plates. The aim of this work is to investigate the impact of the EF correction (EFC) on the heat fluxes at the divertor plates in SPARC. The MHD code M3DC1 has been used to simulate the 3D magnetic perturbations generated by the shift and tilt of several axisymmetric coils within specified tolerances, as well as from the array of EFC coils located at the midplane. Using a heuristic model that extends the concept of an axisymmetric heat flux layer to 3D plasmas, the resultant heat flux distributions is derived from magnetic footprints calculated with the MAFOT code. The results show that the EFC could either decrease or further enhance the local heat flux when used to correct the m,n = 2,1 resonant EF to enhance the core plasma performance.

3D fields↗
DOE OSTI2024

Validation of SOLPS-ITER and EDGE2D-EIRENE simulations for H, D, and T JET ITER-like wall low-confinement mode plasmas

Both experiments and simulations with SOLPS-ITER and EDGE2D-EIRENE show that the onset of detachment for the low-field side (LFS) divertor – defined here as the line-averaged upstream density (〈n e 〉 edge ) at which the plasma flux to the LFS target (I LFS-plate ) starts to decrease with increasing 〈n e 〉 edge – is independent of the isotope mass. However, there are three major simulation-experiment discrepancies: (i) the absolute values of I LFS-plate and the electron density (n e ) in the LFS divertor at the onset of detachment are significantly lower in simulations, i.e., approximately a factor of 2 for I LFS-plate and a factor of 3-4 for n e ; (ii) the degree of detachment – defined here as the difference between I LFS-plate at the onset of detachment and at an 〈n e 〉 edge value close to the density limit – is smaller in simulations compared to experiments; and (iii) the experimentally observed larger degree of detachment for D and T plasmas compared to H plasmas cannot be clearly distinguished from the simulation results. There are strong indications that discrepancy (i) is to a large extent caused by neglecting Lyman-opacity effects in our simulations. The simulations predict a similar net volumetric recombination source for all isotopes due to the fact that molecule-activated recombination (MAR) compensates for the reduced electron–ion recombination (EIR) for H, whereas MAR is negligible for D and T. This similar net volumetric recombination source for all isotopes leads to an isotope-independent degree of detachment in simulations. An analysis of the Balmer-α and Balmer-$γ$ emission confirms the underestimate of MAR in simulations (especially for D and T) for the JET metallic wall, which was previously observed for devices with a carbon wall. The underestimate of MAR is an important cause for discrepancy (ii) and the fact that there is a stronger underestimate of MAR for D and T than for H explains discrepancy (iii). Extending the plasma grid to the vessel wall increases I LFS-plate and n e at the onset of detachment by 25%, and the EIR source increases by 80% in detached conditions. Hence, while the extended grid results are closer to the experimental observations, the previously described qualitative discrepancies still persist.

Balmer emission↗
DOE OSTI2025

Balmer emission measurements in JET-ILW hydrogen, deuterium, tritium and deuterium-tritium low-confinement mode plasmas

Measurements of Balmer-alpha (B-α) and Balmer-gamma (B-γ), where B = H, D, or T isotopes of hydrogen, emission across the low-field side (LFS) divertor in JET ITER-like Wall (ILW), low-confinement mode (L-mode) plasma indicate that the divertor plasma was more strongly detached in deuterium, tritium and deuterium–tritium than in hydrogen plasmas. These measurements are consistent with the lower degree of detachment in hydrogen versus tritium plasmas inferred from Langmuir probes (Groth et al., 2023). The ratio of B-γ to B-α is a suitable indicator of high density/low temperature conditions because B-α emission is dominated by electron impact excitation with a small electron–ion recombination component regardless of electron temperature and density (for conditions in tokamak plasmas) whilst for B-γ the recombination component increases and the excitation component decreases as the electron temperature decreases and the electron density increases. Within the uncertainty of the measurements, the electron density at the low-field side separatrix and the power crossing the separatrix are similar to permit these comparisons. The B-©/B-α ratio is well correlated with the onset of detachment as measured by Langmuir probes (McCracken et al., 1998; Groth et al., 2023). The ratios of B-γ and B-α varied between 0.005 and 0.035 for low-recycling, high-recycling and partially detached conditions, and were 60–70 % higher in partially detached hydrogen than in tritium plasmas. In contrast, the difference between deuterium, tritium and 40–60 % deuterium–tritium is within 10 % and thus within the uncertainties of the measurements. Profiles of the B-α and B-γ emission was measured with two filtered CCDs connected to the visible lost light leg of JET’s mirror link spectroscopy system (Meigs et al., 2010; Lomanowski et al., 2014). Spatially (radial) narrower B-α profiles were measured with increasing isotope mass, while similarly broadened B-γ profiles were measured.

Balmer↗
DOE OSTI2025

Three-Dimensional Heat Flux and Thermal Analysis of Angled Tungsten Samples on DIII-D

ITER-grade tungsten and dispersoid-strengthened tungsten samples with the top surface angled at ~15° towards the incident plasma flux were exposed to 9 H-mode discharges with edge-localized modes (ELMs) in the lower divertor of DIII-D tokamak using the Divertor Material Evaluation System (DiMES). Surface damage included cracking and flaking of material on the two samples farthest away from the plasma strike point, and significant melting of the two samples closest to the strike point. Heat flux and thermal analysis tools new to DIII-D have been applied to better understand this material response and to help optimize the exposure conditions for future experiments. SMITER field-line tracing simulations based on IRTV data and EFIT equilibria estimate an average inter-ELM perpendicular heat flux, 𝑞⊥,𝑖nter−𝐸LM , on the angled surfaces of 10.1 – 19.6 MW/m² for a majority of the 9 discharges, increasing to 15.6 – 24.5 MW/m² for the single, higher-power shot where samples melted. Fast camera data showed shallow intra-ELM melting and re-solidification, which transitioned to bulk inter-ELM melting with melt motion in the 𝐽⃗ 𝑥 𝐵⃗ direction. About 50% of the protruding volume of the most affected sample was displaced via melt-motion. SIERRA thermal modeling software was able to reproduce an onset time of melting consistent with fast camera data and final sample conditions, within < 200 ms. Maximum surface temperatures of 3122 K and 2787 K are estimated for the samples farthest away from the strike point, while the closest samples achieve melting at 4067 ms and 4750 ms into the ~5000 ms plasma exposure. A +10% increase in both the SMITER 𝑞⊥,𝑖nter−𝐸LM calculations and the estimated ELM heat loads 𝑞⊥, 𝐸LM was required to achieve this result, which is within the uncertainty of the diagnostic data but likely accounts for non-ideal geometry effects plus other physics uncertainties not included in this first iteration of modeling. This work provided valuable estimates of the 3D temperature evolution to help better understand the observed surface morphology and internal recrystallization of samples, which are discussed in detail in a complementary manuscript [1]. Benchmarking efforts with more diagnosed DIII-D experiments are underway to further refine the SMITER and SIERRA models for DiMES. Future use of these tools will enable researchers to precisely target heat flux exposure conditions in DIII-D to test, but not exceed, the thermomechanical limitations of novel plasma-facing materials.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Overview of the first Wendelstein 7-X long pulse campaign with fully water-cooled plasma facing components

After a long device enhancement phase, scientific operation resumed in 2022. The main new device components are the water cooling of all plasma facing components and the new water-cooled high heat flux divertor units. Water cooling allowed for the first long-pulse operation campaign. A maximum discharge length of 8 min was achieved with a total heating energy of 1.3 GJ. Safe divertor operation was demonstrated in attached and detached mode. Stable detachment is readily achieved in some magnetic configurations but requires impurity seeding in configurations with small magnetic pitch angle within the edge islands. Progress was made in the characterization of transport mechanisms across edge magnetic islands: Measurement of the potential distribution and flow pattern reveals that the islands are associated with a strong poloidal drift, which leads to rapid convection of energy and particles from the last closed flux surface into the scrape-off layer. Using the upgraded plasma heating systems, advanced heating scenarios were developed, which provide improved energy confinement comparable to the scenario, in which the record triple product for stellarators was achieved in the previous operation campaign. However, a magnetic configuration-dependent critical heating power limit of the electron cyclotron resonance heating was observed. Exceeding the respective power limit leads to a degradation of the confinement.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Overview of the ASDEX Upgrade results

After a 26-month vent ASDEX Upgrade (AUG) went back in operation with a newly designed upper W-divertor suitable for alternative divertor configurations (featuring in-vessel coils and cryo-pump). Parameter scans and an extensive set of measurements were obtained and their interpretation is ongoing. Prompted by the ITER wall change, dedicated experiments on non-boronized plasma startup were contrasted to that employing asymmetric and more symmetric boronizations. The asymmetric boronization proved to be as beneficial as the more symmetric one, which is in contrast to previous model calculations assuming perfect sticking of boron (measurements suggest sticking ≈ 0.3). In the startup phase also the impurity influxes at the outboard limiters were investigated contrasting the unboronized case featuring cold edges (low- Z radiation) to the boronized case, in which the lifetime of the boron layers could be estimated. Pedestal stability investigations revealed that the quasi-continuous exhaust (QCE) regime is obtained when ballooning modes are active in the vicinity of the separatrix and the global peeling-ballooning stability is high enough. Thus, at high enough shaping and high gas flux both can be achieved and QCE is a consequence. The closely related enhanced D-alpha (EDA) mode is not clearly distinguishable from QCE, e.g. the quasi-coherent mode characteristic for EDA also shows up in QCE. In QCE the impurity transport is behaving benign as could be measured for Ne with a novel analysis method making use of a comprehensive set of CXRS measurements. For high radiative fractions the regime of the X-point radiator (XPR) is accessible at AUG and the understanding of its access conditions and behaviour is further developed. Due to the localized radiative cooling at the X-point the XPR can be well diagnosed and thus controlled. For negative triangularity shapes, further experiments at increased shaping resulted in strongly heated L-mode plasmas avoiding ELMs. Two integrated modelling approaches towards ITER suggested that core W-accumulation will be no issue for ITER and that the fusion yield in ITER may be Q = 12 (i.e. ITPA20-IL scaling is too pessimistic). Further, investigations of the ITER ramp-down in AUG provide insights into maintaining position control. Various aspects of shattered pellet injection were investigated in AUG and one of the results show that with increasing Ne fraction the radiation during the current quench increases and the current decay becomes faster.

ASDEX Upgrade↗
DOE OSTI2025

Basic Physical Processes Involving Dust in Fusion Plasmas

This report presents the main outcomes of our research focused on understanding the behavior and effects of dust particles in fusion plasmas, particularly in the edge regions of tokamaks and stellarators. We conducted computer modeling studies of burst injections of carbon and tungsten dust particles in DIII-D like divertor plasmas. The studies investigated effects of transient influx of the low- and high-Z material plasma contaminants in form of dust on the edge plasma dynamics in a modern mid-size tokamak. We also performed theoretical and computational studies of the forces acting on non-spherical dust grains in magnetized and nonmagnetized plasmas. In addition, we cooperated with General Atomics slag management group on development of DIII-D dust injection experiments to measure trajectories of dust grains in the divertor plasma and compare them with DUSTT code predictions for validation of the dust modeling capabilities. We collaborated with JET experimentalists on evaluation of radiative losses induced by injection of mixed neon-deuterium ice pellets for disruption and run-away electron generation mitigation during thermal and current quench phases. We also cooperated with experimentalists at LHD fusion device (Japan) on modeling support of experiments on injection of boron granules in fusion plasma discharges to assess their dynamics and effectiveness for in situ dynamic wall conditioning.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Shadow masks predictions in SPARC tokamak plasma-facing components using HEAT code and machine learning methods

Here, this work uses machine learning (ML) to complement HEAT (Heat flux Engineering Analysis Toolkit) by developing 3-D footprint surrogate models for fast and accurate heat load calculations in the divertor of the SPARC tokamak. The focus is on shadowed regions, or magnetic shadows, caused by the 3-D geometry of plasma-facing components (PFCs). ML classifiers are employed to create a surrogate model for HEAT generated shadow masks, predicting these shadow masks and divertor heat flux profiles based on a diverse range of equilibria and only the plasma current, safety factor(q95) at the edge, and magnetic flux angles as input parameters. The ultimate goal is to integrate the model for real-time control and future operational decisions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Thermal and structural analysis of a new WEST reciprocating probe head with Titanium-Zirconium-Molybdenum armour material

The Tore Supra tokamak was transformed into an X-point divertor fusion device in the frame of the WEST (W-for tungsten-Environment in Steady-state Tokamak) project, launched in support of the ITER tungsten divertor strategy. WEST began operation in 2017. A new reciprocating probe head, equipped with a Titanium-Zirconium-Molybdenum (TZM) heat shield, was recently built and operated on WEST during the C9 Campaign in early 2024. TZM was chosen as armour material for its very good mechanical properties between 700 °C and 1400 °C. This material was already extensively used for probe heads and other plasma facing components on the Alcator C-Mod tokamak. Here, this paper presents the design of the new WEST probe head. It is equipped with tungsten filaments that can be heated to emit electrons and provide a direct measurement of the plasma potential in the scrape-off layer, and it is also equipped with a pair of Langmuir probes. The probe plunges vertically into the plasma, reaches its maximum dive depth, then returns to its protected resting position in about 0.25 s. Thermal loads are calculated using as input the thermal properties of TZM and radial profiles of the heat flux measured in the past by other reciprocating probes, and scaled upwards to the expected heat loads in the WEST scrape-off layer. An analytical estimation of Electromagnetic (EM) loads will also be presented, as well as a thermal and structural analysis of the probe for 15 cycles at maximum plunge depth. The probe is observed by an infrared camera. Comparisons between the heat flux deduced by the Langmuir probe and the infrared radiance of the probe housing during plasma exposure are finally presented.

Diagnostic↗