Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Diffusion coefficient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Determination and Comparison of Parameters from Cyclic Voltammetry of LaCl 3 in Eutectic LiCl-KCl

Electrochemical measurements of LaCl 3 were obtained in eutectic LiCl-KCl at 773 K. Cyclic voltammetry data were acquired using a tungsten electrode LaCl 3 amounts in the molten salt in the range of 0.5 to 3.0 wt%. Both cyclic voltammetry and Tafel analyses of the data resulted in calculation of values for the charge transfer coefficient (0.262), diffusion coefficient (1.67 × 10 -5 cm 2 s -1 ), exchange current density (0.0148 to 0.0473 A cm -2 ), and charge transfer resistance (0.404 to 1.99 Ω) related to lanthanum ions in the molten salt. Calculated values were compared to those available in the literature. The values of parameters found in literature varied significantly in comparison to those in the present study due to dissimilar experimental conditions, e.g., electrode material, temperature, and LaCl 3 concentration.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1973

Transient permeation of organic vapors through elastomeric membranes

The permeation of benzene and acetone vapors through sulfur-cured natural rubber was studied by the time-lag method. The zero concentration diffusion coefficient, was obtained by the early-time method. The Frisch time lag equation was utilized to estimate both the solubility coefficient and the additional parameter required to define the concentration-dependence of the diffusion coefficient. This form of concentration dependence was manifested by the corresponding permeability coefficient values. At low entering penetrant pressure where the transport coefficients are constant, indirect evidence was obtained that zero diffusion coefficient is the mechanically correct diffusion coefficient. The solubility coefficient values calculated for benzene vapor in natural rubber are in reasonable agreement with published equilibrium sorption data for a similar rubber compound. At higher entering penetrant pressures, average diffusion coefficients obtained at steady state tended to be larger than the corresponding average diffusion coefficients derived from the time-lags.

Curry, J. E.↗
DOE OSTI2022

The effect of stress on the migration of He gas bubbles under a thermal gradient in Fe by phase-field modeling

Here a phase-field model is parameterized to study the effect of elastic stresses on the migration of He gas bubbles in Fe under a temperature gradient. Stresses caused by the gas bubble pressure and residual stress in the Fe matrix are considered. The dependence of He bubble migration velocity on the magnitude of the residual stress, average temperature, temperature gradient, and bubble size is measured. In agreement with a theoretical model based on surface diffusion, simulation results demonstrate that He bubbles move towards the high temperature region with velocities in Fe that are orders of magnitude faster than previously reported in UO 2 . It is found that local stresses in the matrix caused by the He bubble have negligible effect on the bubble migration process; however, residual stresses in the Fe matrix, potentially caused by processing or irradiation, can modestly modify bubble kinetics through pressure dependence of the He diffusion coefficients. Compressive residual stress decreases diffusion coefficients for bulk and surface diffusion mechanisms, thus reducing the migration velocity of the gas bubble. In contrast, tensile residual stress increases the diffusion coefficients, resulting in an increase in the gas bubble migration velocity. This pressure dependence is also consistent with a theoretical model. This phase field model lays the foundation for analysis of bubble coalescence-induced fracture in He bubble-containing steels.

36 MATERIALS SCIENCE↗
NASA NTRS2002

Static and Dynamic Effects of Lateral Carrier Diffusion in Semiconductor Lasers

Electron and hole diffusions in the plane of semiconductor quantum wells play an important part in the static and dynamic operations of semiconductor lasers. It is well known that the value of diffusion coefficients affects the threshold pumping current of a semiconductor laser. At the same time, the strength of carrier diffusion process is expected to affect the modulation bandwidth of an AC-modulated laser. It is important not only to investigate the combined DC and AC effects due to carrier diffusion, but also to separate the AC effects from that of the combined effects in order to provide design insights for high speed modulation. In this presentation, we apply a hydrodynamic model developed by the present authors recently from the semiconductor Bloch equations. The model allows microscopic calculation of the lateral carrier diffusion coefficient, which is a nonlinear function of the carrier density and plasma temperature. We first studied combined AC and DC effects of lateral carrier diffusion by studying the bandwidth dependence on diffusion coefficient at a given DC current under small signal modulation. The results show an increase of modulation bandwidth with decrease in the diffusion coefficient. We simultaneously studied the effects of nonlinearity in the diffusion coefficient. To clearly identify how much of the bandwidth increase is a result of decrease in the threshold pumping current for smaller diffusion coefficient, thus an effective increase of DC pumping, we study the bandwidth dependence on diffusion coefficient at a given relative pumping. A detailed comparison of the two cases will be presented.

Li, Jian-Zhong↗
DOE OSTI2021

Modeling fission product diffusion in TRISO fuel particles with BISON

Diffusion of fission products in intact TRISO particles depends on particle geometry, fission product source rates, time, temperature, and temperature-dependent diffusion coefficients. Simulating this diffusion process requires models for source rates and diffusion coefficients, plus computation of the temperature field if not prescribed. In addition, simulation quality depends on discretization of the geometry, appropriate time stepping, and the accuracy of the solution method. In this paper, we explore the simulation of fission product diffusion in TRISO fuel particles using the finite element method via the fuel performance code Bison. Recent material model development has occurred in Bison for each material present in tri-structural isotropic (TRISO) fuel particles: the buffer, inner pyrolytic carbon, silicon carbide, and outer pyrolytic carbon layers, as well as the fuel kernel. Also, new mesh generation and fission product release fraction capabilities have been added. Diffusion capabilities are shown to converge to the correct solution via formal verification tests. A large number of code benchmarking problems are also given, with good results, showing that Bison’s computed release fractions closely match those of other software tools. Finally, a significant validation effort is detailed in which fission product release, measured as part of the AGR-1 capsule experiments, is compared to Bison outputs. Bison outputs compare very well to the experimental data and to PARFUME results.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Theoretical Examination of the Hydroxide Transport in Cobaltocenium-Containing Polyelectrolytes

Polymers incorporating cobaltocenium groups have received attention as promising components of anion-exchange membranes (AEMs), exhibiting a good balance of chemical stability and high ionic conductivity. In this work, we analyze the hydroxide diffusion in the presence of cobaltocenium cations in an aqueous environment based on the molecular dynamics of model systems confined in one dimension to mimic the AEM channels. In order to describe the proton hopping mechanism, the forces are obtained from the electronic structure computed at the density-functional tight-binding level. We find that the hydroxide diffusion depends on the channel size, modulation of the electrostatic interactions by the solvation shell, and its rearrangement ability. Hydroxide diffusion proceeds via both the vehicular and structural diffusion mechanisms with the latter playing a larger role at low diffusion coefficients. The highest diffusion coefficient is observed under moderate water densities (around half the density of liquid water) when there are enough water molecules to form the solvation shell, reducing the electrostatic interaction between ions, yet there is enough space for the water rearrangements during the proton hopping. Furthermore, the effects of cobaltocenium separation, orientation, chemical modifications, and the role of nuclear quantum effects are also discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1981

Dynamics of solar cosmic ray events - Processes at large heliocentric distances /much greater than 1 AU/

Observations of solar cosmic ray events at heliocentric distances up to 6 AU and beyond obtained by the Pioneer 10 and 11 spacecraft are discussed in terms of the propagation of energetic charged particles in interplanetary space. Following a review of the diffusion propagation model used to explain cosmic ray transport, the statistical studies of McCarthy and O'Gallagher (1976) and Zwickl and Webber (1977) of the relations of event parameters with radial distance and the simultaneous observation studies of Hamilton (1977) are reviewed, and it is noted that the results imply a slowly increasing radial diffusion coefficient out to about 6 AU. More recent analyses of data obtained at heliocentric distances greater than 10 AU are then presented which indicate that the coefficient of radial diffusion may actually be decreasing with radial distance beyond 5 AU. Finally, theoretical predictions of the radial variation of the diffusion coefficient are presented which take into account the background interplanetary medium and are shown to be in agreement with observations.

Hamilton, D. C.↗
NASA NTRS1978

Geomagnetic field fluctuations at synchronous orbit. II - Radial diffusion

Power spectra of geomagnetic-field variations measured at synchronous equatorial altitude (geomagnetic shell parameter about 6.6) in the magnetosphere are used to calculate the time dependence of the radial diffusion coefficient for particles in the radiation belts. The diffusion coefficients calculated are mainly applicable for relativistic electrons. The magnitudes of the derived diffusion coefficients using data only from local day observations are consistent with those reported from analyses of most particle observations and thus are slightly larger than those derived from magnetic sudden commencements. They are consistent with the diffusion coefficients calculated from power spectra of ground-based geomagnetic data measured near L = 4.

Lanzerotti, L. J.↗
NASA NTRS1975

A feasibility study for measuring stratospheric turbulence using metrac positioning system

The feasibility of obtaining measurements of Lagrangian turbulence at stratospheric altitudes is demonstrated by using the METRAC System to track constant-level balloons. The basis for current estimates of diffusion coefficients are reviewed and it is pointed out that insufficient data is available upon which to base reliable estimates of vertical diffusion coefficients. It is concluded that diffusion coefficients could be directly obtained from Lagrangian turbulence measurements. The METRAC balloon tracking system is shown to possess the necessary precision in order to resolve the response of constant-level balloons to turbulence at stratospheric altitudes. A small sample of data recorded from a tropospheric tetroon flight tracked by the METRAC System is analyzed to obtain estimates of small-scale three-dimensional diffusion coefficients. It is recommended that this technique be employed to establish a climatology of diffusion coefficients and to ascertain the variation of these coefficients with altitude, season, and latitude.

Gage, K. S.↗
NASA NTRS2003

High-Pressure Transport Properties Of Fluids: Theory And Data From Levitated Drops At Combustion-Relevant Temperatures

Although the high pressure multicomponent fluid conservation equations have already been derived and approximately validated for binary mixtures by this PI, the validation of the multicomponent theory is hampered by the lack of existing mixing rules for property calculations. Classical gas dynamics theory can provide property mixing-rules at low pressures exclusively. While thermal conductivity and viscosity high-pressure mixing rules have been documented in the literature, there is no such equivalent for the diffusion coefficients and the thermal diffusion factors. The primary goal of this investigation is to extend the low pressure mixing rule theory to high pressures and validate the new theory with experimental data from levitated single drops. The two properties that will be addressed are the diffusion coefficients and the thermal diffusion factors. To validate/determine the property calculations, ground-based experiments from levitated drops are being conducted.

Bellan, Josette↗
DOE OSTI2026

Electrode and Microstructure Dependence of Oxygen Diffusion in Ferroelectric Hafnium Zirconium Oxide Thin Films

Hafnia-based ferroelectrics hold promise to reduce energy demand for computing by enabling compute-in-memory and as non-volatile memories. The ferroelectric phase in this material system is, in part, stabilized by oxygen vacancies. While oxygen vacancies may be a necessity for phase stability, they limit device endurance through diffusion and accumulation into conducting channels. Herein, it is shown that oxygen diffusion is spatially variable within individual grains of ferroelectric hafnium zirconium oxide (HZO). Using 18 O tracers and finite difference modeling, it is shown that grain boundaries and regions near electrode interfaces allow for relatively rapid oxygen diffusion, with values as much as 10 4 larger than the grain cores. Further, the selection of electrode material affects the diffusion coefficients across all microstructural regions. HZO films in contact with TiN electrodes result in more oxygen-deficient HZO films and higher oxygen diffusion coefficients. Tungsten electrodes result in fewer vacancies and lower diffusion coefficients. Diffusion activation energy differences between the HZO with the two electrodes is reconciled by differing populations of charged and uncharged oxygen vacancies. This insight into the local vacancy populations and diffusion pathways provides a platform for designing hafnia-based films, deposition processes, and integration strategies to reduce vacancy gradients and improve performance.

36 MATERIALS SCIENCE↗
NASA NTRS1973

A study of the force-field equation for the propagation of galactic cosmic rays

A new development is given of the solution of the equation of the force-field approximation for the propagation of galactic cosmic rays in the interplanetary region. It leads to simpler methods for determining the force-field parameters. A method is given for determining the separable diffusion coefficient from observations of galactic electron spectrum and near-earth electron spectra; it is shown that this diffusion coefficient is not unique but may have a periodic-like dependence upon rigidity; and the method is used to obtain diffusion coefficients for 1965 and 1968. Approximate formulae relating small changes in intensity and diffusion coefficient are developed and some applications of these noted; in one it is shown that the form of, and changes in, diffusion coefficient deduced previously for a neutron monitor event during June-September 1969 are unnecessarily constrained and therefore probably not correct.

Gleeson, L. J.↗
NASA NTRS2001

A Hydrodynamic Theory for Spatially Inhomogeneous Semiconductor Lasers: Microscopic Approach

Starting from the microscopic semiconductor Bloch equations (SBEs) including the Boltzmann transport terms in the distribution function equations for electrons and holes, we derived a closed set of diffusion equations for carrier densities and temperatures with self-consistent coupling to Maxwell's equation and to an effective optical polarization equation. The coherent many-body effects are included within the screened Hartree-Fock approximation, while scatterings are treated within the second Born approximation including both the in- and out-scatterings. Microscopic expressions for electron-hole (e-h) and carrier-LO (c-LO) phonon scatterings are directly used to derive the momentum and energy relaxation rates. These rates expressed as functions of temperatures and densities lead to microscopic expressions for self- and mutual-diffusion coefficients in the coupled density-temperature diffusion equations. Approximations for reducing the general two-component description of the electron-hole plasma (EHP) to a single-component one are discussed. In particular, we show that a special single-component reduction is possible when e-h scattering dominates over c-LO phonon scattering. The ambipolar diffusion approximation is also discussed and we show that the ambipolar diffusion coefficients are independent of e-h scattering, even though the diffusion coefficients of individual components depend sensitively on the e-h scattering rates. Our discussions lead to new perspectives into the roles played in the single-component reduction by the electron-hole correlation in momentum space induced by scatterings and the electron-hole correlation in real space via internal static electrical field. Finally, the theory is completed by coupling the diffusion equations to the lattice temperature equation and to the effective optical polarization which in turn couples to the laser field.

Li, Jianzhong↗
DOE OSTI2022

Investigation of Molecular Diffusion at Block Copolymer Thin Films Using Maximum Entropy Method-Based Fluorescence Correlation Spectroscopy and Single Molecule Tracking

Fluorescence correlation spectroscopy (FCS) has been widely used to investigate molecular diffusion behavior in various samples. The use of the maximum entropy method (MEM) for FCS data analysis provides a unique means to determine multiple distinct diffusion coefficients without a priori assumption of their number. Comparison of the MEM-based FCS method (MEM-FCS) with another method will reveal its utility and advantage as an analytical tool to investigate diffusion dynamics. Herein, we measured diffusion of fluorescent probes doped into nanostructured thin films using MEM-FCS, and validated the results with single molecule tracking (SMT) data. The efficacy of the MEM code employed was first demonstrated by analyzing simulated FCS data for systems incorporating one and two diffusion modes with broadly distributed diffusion coefficients. The MEM analysis accurately afforded the number of distinct diffusion modes and their mean diffusion coefficients. These results contrasted with those obtained by fitting the simulated data to conventional two-component and anomalous diffusion models, which yielded inaccurate estimates of the diffusion coefficients. Subsequently, the MEM analysis was applied to FCS data acquired from hydrophilic dye molecules incorporated into microphase-separated polystyrene-block-poly(ethylene oxide) (PS-b-PEO) thin films characterized under a water-saturated nitrogen atmosphere. The MEM analysis revealed distinct fast and slow diffusion components attributable to molecules diffusing on the film surface and inside the film, respectively. SMT studies of the same materials yielded trajectories for mobile molecules that appear to follow the curved PEO microdomains. Diffusion coefficients obtained from the SMT data were consistent with those obtained for the slow diffusion component detected by MEM-FCS. Furthermore, these results highlight the utility of MEM-FCS and SMT for gaining complementary information on molecular diffusion processes in heterogeneous material systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Computational determination of a primary diffusion mode in γ U-10Mo under irradiation

Low enriched uranium (< 20 % 235 U)-molybdenum (U-Mo) monolithic fuel is the primary candidate for high performance research and test reactors, and is in the process of being qualified to replace highly enriched uranium (≥ 20 % 23 5U) fuel. As part of the qualification process, it is critical to understand and predict the behavior of fission gas bubbles under irradiation, which affects fuel swelling and fuel failure. Mechanistic fuel models are being developed that can both reproduce the existing experimental data for fuel swelling, and be further applied to irradiation conditions beyond the experimental scope. Diffusion of species under irradiation conditions is an important parameter in the mechanistic fuel models; however, no temperature-relevant experimental diffusion data exists. In the present work, radiation-enhanced diffusion coefficients of U, Mo, and Xe in λU-10wt.%Mo were calculated in the temperature range between 300 K and 1400 K via rate-theory models and molecular dynamics simulations with an embedded-atom method interatomic potential for the U-Mo-Xe system. Accordingly, total diffusion coefficients under relevant irradiation conditions are determined using previously obtained intrinsic thermal diffusion and radiation-driven diffusion coefficients, as well as the newly calculated radiation-enhanced diffusion coefficients presented herein. Radiation-enhanced diffusion of U and Mo was dominant in the intermediate temperature range, whereas radiation-enhanced diffusion of Xe did not significantly contribute to total diffusion of Xe at the relevant fission rate densities. Radiation-enhanced diffusion of Xe became faster than both intrinsic thermal diffusion and radiation-driven diffusion at a fission rate density of 5 x 10 22 fissions/m 3 /s, which is higher than the typical fission rate density range in research reactors. The temperature regime that radiation-enhanced diffusion of each element dominated was dependent on the fission rate density. Finally, the total diffusion coefficients of U, Mo, and Xe, updated in this work, will be utilized as parameters in the mechanistic fuel models to help predict the behavior of fission gas bubbles under irradiation more accurately.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Turbulence-level dependence of cosmic ray parallel diffusion

ABSTRACT Understanding the transport of energetic cosmic rays belongs to the most challenging topics in astrophysics. Diffusion due to scattering by electromagnetic fluctuations is a key process in cosmic ray transport. The transition from a ballistic to a diffusive-propagation regime is presented in direct numerical calculations of diffusion coefficients for homogeneous magnetic field lines subject to turbulent perturbations. Simulation results are compared with theoretical derivations of the parallel diffusion coefficient’s dependences on the energy and the fluctuation amplitudes in the limit of weak turbulence. The present study shows that the widely used extrapolation of the energy scaling for the parallel diffusion coefficient to high turbulence levels predicted by quasi-linear theory does not provide a universally accurate description in the resonant-scattering regime. It is highlighted here that the numerically calculated diffusion coefficients can be polluted for low energies due to missing resonant interaction possibilities of the particles with the turbulence. Five reduced-rigidity regimes are established, which are separated by analytical boundaries derived in this work. Consequently, a proper description of cosmic ray propagation can only be achieved by using a turbulence-level-dependent diffusion coefficient and can contribute to solving the Galactic cosmic ray gradient problem.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2024

Cosmic-Ray Feedback on Bistable Interstellar Medium Turbulence

Abstract While cosmic rays ( E ≳ 1 GeV) are well coupled to a galaxy’s interstellar medium (ISM) at scales of L > 100 pc, adjusting stratification and driving outflows, their impact on small scales is less clear. Based on calculations of the cosmic-ray diffusion coefficient from observations of the grammage in the Milky Way, cosmic rays have little time to dynamically impact the ISM on those small scales. Using numerical simulations, we explore how more complex cosmic-ray transport could allow cosmic rays to couple to the ISM on small scales. We create a two-zone model of cosmic-ray transport, with the cosmic-ray diffusion coefficient set at the estimated Milky Way value in cold gas but smaller in warm gas. We compare this model to simulations with a constant diffusion coefficient. Quicker diffusion through cold gas allows more cold gas to form compared to a simulation with a constant, small diffusion coefficient. However, slower diffusion in warm gas allows cosmic rays to take energy from the turbulent cascade anisotropically. This cosmic-ray energization comes at the expense of turbulent energy which would otherwise be lost during radiative cooling. Finally, we show our two-zone model is capable of matching observational estimates of the grammage for some transport paths through the simulation.

79 ASTRONOMY AND ASTROPHYSICS↗