Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “DYNAMIC PRESSURE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1959

Experimental Investigation of Flutter of Buckled Curved Panels Having Longitudinal Stringers at Transonic and Supersonic Speeds

Panel-flutter tests have been made at transonic and supersonic speeds With particular reference to buckled curved panels with longitudinal stringers. Other panel configurations were also tested in an attempt to determine effects of skin thickness, curvature, stringers, buckling, pressure differential, and Mach number on the dynamic pressure necessary to start flutter. For buckled curved panels with longitudinal stringers, the dynamic pressure required to start flutter was increased by increasing the skin thickness and increasing the pressure differential across the panel. There was no apparent effect of Mach number variation from 1.3 to 2.0. None of the curved panels failed because of flutter although the dynamic pressure at the start of flutter was exceeded by a factor of 3 in many cases. curved panels and four flat panels failed because of flutter. The flat panels fluttered at lower dynamic pressures than the curved panels and four flat panels failed because of flutter.

Tuovila, W. J.↗
NASA NTRS2011

Flight Test Results from the Rake Airflow Gage Experiment on the F-15B

The results are described of the Rake Airflow Gage Experiment (RAGE), which was designed and fabricated to support the flight test of a new supersonic inlet design using Dryden's Propulsion Flight Test Fixture (PFTF) and F-15B testbed airplane (see figure). The PFTF is a unique pylon that was developed for flight-testing propulsion-related experiments such as inlets, nozzles, and combustors over a range of subsonic and supersonic flight conditions. The objective of the RAGE program was to quantify the local flowfield at the aerodynamic interface plane of the Channeled Centerbody Inlet Experiment (CCIE). The CCIE is a fixed representation of a conceptual mixed-compression supersonic inlet with a translating biconic centerbody. The primary goal of RAGE was to identify the relationship between free-stream and local Mach number in the low supersonic regime, with emphasis on the identification of the particular free-stream Mach number that produced a local Mach number of 1.5. Measurements of the local flow angularity, total pressure distortion, and dynamic pressure over the interface plane were also desired. The experimental data for the RAGE program were obtained during two separate research flights. During both flights, local flowfield data were obtained during straight and level acceleration segments out to steady-state test points. The data obtained from the two flights showed small variations in Mach number, flow angularity, and dynamic pressure across the interface plane at all flight conditions. The data show that a free-stream Mach number of 1.65 will produce the desired local Mach number of 1.5 for CCIE. The local total pressure distortion over the interface plane at this condition was approximately 1.5%. At this condition, there was an average of nearly 2 of downwash over the interface plane. This small amount of downwash is not expected to adversely affect the performance of the CCIE inlet.

Frederick, Michael↗
NASA NTRS1972

Effects of Leading-Edge Camber on Low-Speed Characteristics of Slender Delta Wings: Techniques and Tabulated Data

Special tests to determine the importance of transition fixing and Reynolds number variation on forces produced by thin delta wings are discussed. Transition fixing was achieved by applying cement to models and sprinkling grit on wet adhesive. Strips were applied along lines emanating from the apex located along sixty-five percent semi-span rays. Tests were made with grit on both surfaces, upper surface only, lower surface only, and on clean surfaces. Reynolds number varied by testing at three dynamic pressures. Correspondence between dynamic pressure and Reynolds number based on the mean aerodynamic chord are shown. No significant changes are noted due to either Reynolds number variation or transition fixing, within the range of Reynolds numbers used for the test.

Wentz, W. H., Jr.↗
NASA NTRS2011

Comprehensive Forced Response Analysis of J2X Turbine Bladed-Discs with 360 Degree Variation in CFD Loading

The temporal frequency content of the dynamic pressure predicted by a 360 degree computational fluid dynamics (CFD) analysis of a turbine flow field provides indicators of forcing function excitation frequencies (e.g., multiples of blade pass frequency) for turbine components. For the Pratt and Whitney Rocketdyne J-2X engine turbopumps, Campbell diagrams generated using these forcing function frequencies and the results of NASTRAN modal analyses show a number of components with modes in the engine operating range. As a consequence, forced response and static analyses are required for the prediction of combined stress, high cycle fatigue safety factors (HCFSF). Cyclically symmetric structural models have been used to analyze turbine vane and blade rows, not only in modal analyses, but also in forced response and static analyses. Due to the tortuous flow pattern in the turbine, dynamic pressure loading is not cyclically symmetric. Furthermore, CFD analyses predict dynamic pressure waves caused by adjacent and non-adjacent blade/vane rows upstream and downstream of the row analyzed. A MATLAB script has been written to calculate displacements due to the complex cyclically asymmetric dynamic pressure components predicted by CFD analysis, for all grids in a blade/vane row, at a chosen turbopump running speed. The MATLAB displacements are then read into NASTRAN, and dynamic stresses are calculated, including an adjustment for possible mistuning. In a cyclically symmetric NASTRAN static analysis, static stresses due to centrifugal, thermal, and pressure loading at the mode running speed are calculated. MATLAB is used to generate the HCFSF at each grid in the blade/vane row. When compared to an approach assuming cyclic symmetry in the dynamic flow field, the current approach provides better assurance that the worst case safety factor has been identified. An extended example for a J-2X turbopump component is provided.

Elrod, David↗
NASA NTRS2014

Repeatability Modeling for Wind-Tunnel Measurements: Results for Three Langley Facilities

Data from extensive check standard tests of seven measurement processes in three NASA Langley Research Center wind tunnels are statistically analyzed to test a simple model previously presented in 2000 for characterizing short-term, within-test and across-test repeatability. The analysis is intended to support process improvement and development of uncertainty models for the measurements. The analysis suggests that the repeatability can be estimated adequately as a function of only the test section dynamic pressure over a two-orders- of-magnitude dynamic pressure range. As expected for low instrument loading, short-term coefficient repeatability is determined by the resolution of the instrument alone (air off). However, as previously pointed out, for the highest dynamic pressure range the coefficient repeatability appears to be independent of dynamic pressure, thus presenting a lower floor for the standard deviation for all three time frames. The simple repeatability model is shown to be adequate for all of the cases presented and for all three time frames.

Hemsch, Michael J.↗
NASA NTRS1994

Active load control during rolling maneuvers

A rolling maneuver load alleviation (RMLA) system has been demonstrated on the active flexible wing (AFW) wind tunnel model in the Langley Transonic Dynamics Tunnel (TDT). The objective was to develop a systematic approach for designing active control laws to alleviate wing loads during rolling maneuvers. Two RMLA control laws were developed that utilized outboard control-surface pairs (leading and trailing edge) to counteract the loads and that used inboard trailing-edge control-surface pairs to maintain roll performance. Rolling maneuver load tests were performed in the TDT at several dynamic pressures that included two below and one 11 percent above open-loop flutter dynamic pressure. The RMLA system was operated simultaneously with an active flutter suppression system above open-loop flutter dynamic pressure. At all dynamic pressures for which baseline results were obtained, torsion-moment loads were reduced for both RMLA control laws. Results for bending-moment load reductions were mixed; however, design equations developed in this study provided conservative estimates of load reduction in all cases.

Woods-Vedeler, Jessica A.↗
NASA NTRS2006

Solar Wind Excitation of Pc5 Fluctuations in the Magnetosphere and on the Ground

The primary purpose of this paper is to show the strong link between solar wind compressional fluctuations in the 1-8 mHz frequency range and Pc5 fluctuations in the magnetosphere near the magnetopause, at geosynchronous orbit, over the poles, and on the ground. We focus on a time interval in March and April 2002 when there was a favorable alignment of satellites combined with ten high speed solar wind streams. We used the S3C Great Observatory: specifically, ACE and Wind in the solar wind, Geotail near the magnetopause, GOES 8 and 10 at geosynchronous orbit, Cluster over the poles, and CANOPUS/CARISMA ground stations near the footpoints of magnetic field lines connected to either the magnetopause or the GOES satellites. Using four examples and a statistical survey we show that magnetospheric Pc5 fluctuations exist regardless of IMF orientation and for a wide range of speeds and dynamic pressures; the amplitude and power of magnetospheric fluctuations depends primarily on the amplitude and power of solar wind dynamic pressure fluctuations. The driving and response frequency of these geoeffective fluctuations is in the range 0.5 - 4 mHz. The most striking magnetospheric response occurs when the solar wind speed, dynamic pressure, and dynamic pressure fluctuations all increase at approximately the same time, as frequently occurs near the leading edge of high speed streams. We show evidence of oscillating Poynting Flux at the magnetopause determined using Geotail data that both excites a FLR and propagates evanescently inward. These observations suggest that, at least for this time interval at spring equinox, the entry path is from the dayside equatorial magnetopause inward; multiple field line resonances may be excited from the magnetopause to geosynchronous orbit by propagating compressional waves, with the power decreasing inward away from the magnetopause.

Kessel, Ramona L.↗
NASA NTRS2001

Solar Wind Influence on the Oxygen Content of Ion Outflow in the High-Altitude Polar Cap During Solar Minimum Conditions

We correlate solar wind and interplanetary magnetic field (IMF) properties with the properties of O(+) and H(+) during early 1996 (solar minimum) at altitudes between 5.5 and 8.9 R(sub E) geocentric using the Thermal Ion Dynamics Experiment (TIDE) on the Polar satellite. Throughout the high-altitude polar cap we observe H(+) to be more abundant than O(+). O(+) is found to be more abundant at lower latitudes when the solar wind speed is low (and Kp is low), while at higher solar wind speeds (and high Kp), O(+) is observed across most of the polar cap. The O(+) density and parallel flux are well organized by solar wind dynamic pressure, both increasing with solar wind dynamic pressure. Both the O(+) density and parallel flux have positive correlations with both V(sub SW)B(sub IMF) and E(sub SW). No correlation is found between O(+) density and IMF Bz, although a nonlinear relationship with IMF By is observed, possibly due to a strong linear correlation with the dynamic pressure. H(+) is not as highly correlated with solar wind and IMF parameters, although H(+) density and parallel flux are negatively correlated with IMF By and positively correlated with both V(sub SW)B(sub IMF) and E(sub SW). In this solar minimum data set, H(+) is dominant, so that contributions of this plasma to the plasma sheet would have very low O(+) to H(+) ratios.

Elliott, H. A.↗
NASA NTRS1989

Performance and test section flow characteristics of the National Full-Scale Aerodynamics Complex 40- by 80-foot wind tunnel

Results from the performance and test section flow calibration of the 40- by 80-Foot Wind Tunnel are presented. A flow calibration test was conducted in May and June 1987. The goal of the flow calibration test was to determine detailed spatial variations in the 40- by 80-ft test section flow quality throughout the tunnel operational envelope. Data were collected for test section speeds up to 300 knots and for air exchange rates of 0, 5, and 10 percent. The tunnel performance was also calibrated during the detailed mapping of the test section flow field. Experimental results presented indicate that the flow quality in the test section, with the exception of temperature, is relatively insensitive to the level of dynamic pressure and the air exchange rate. The dynamic pressure variation in the test section is within + or - 0.5 deg at all test section velocities. Cross-stream temperature gradients in the test section caused by the air exchange system were documented, and a correction method was established. Streamwise static pressure variation on the centerline is about 1 percent of test section dynamic pressure over 30 ft of the test section length.

Zell, Peter T.↗
NASA NTRS1991

Solar wind control of the magnetopause shape, location, and motion

A data set of 1821 magnetopause crossings was assembled. Separate fits to subsets of this data set determine the magnetopause location as a function of solar wind dynamic pressure and interplanetary magnetic field orientation. Solar wind dynamic pressure variations produce self-similar magnetopause motion on time scales of one hour or longer. In this paper, the pressure balance relationship between the solar wind dynamic pressure and the location of the subsolar magnetopause are verified. The relationship between the IMF Bz, region 1 Birkeland current strength, the position of the subsolar magnetopause, and the shape of the dayside magnetosphere is quantified. Cross sections of the dayside magnetopause in planes perpendicular to the earth-sun line are oblate.

Sibeck, D. G.↗
NASA NTRS2016

Experimental Verification of Buffet Calculation Procedure Using Unsteady PSP

Typically a limited number of dynamic pressure sensors are employed to determine the unsteady aerodynamic forces on large, slender aerospace structures. The estimated forces are known to be very sensitive to the number of the dynamic pressure sensors and the details of the integration scheme. This report describes a robust calculation procedure, based on frequency-specific correlation lengths, that is found to produce good estimation of fluctuating forces from a few dynamic pressure sensors. The validation test was conducted on a flat panel, placed on the floor of a wind tunnel, and was subjected to vortex shedding from a rectangular bluff-body. The panel was coated with fast response Pressure Sensitive Paint (PSP), which allowed time-resolved measurements of unsteady pressure fluctuations on a dense grid of spatial points. The first part of the report describes the detail procedure used to analyze the high-speed, PSP camera images. The procedure includes steps to reduce contamination by electronic shot noise, correction for spatial non-uniformities, and lamp brightness variation, and finally conversion of fluctuating light intensity to fluctuating pressure. The latter involved applying calibration constants from a few dynamic pressure sensors placed at selective points on the plate. Excellent comparison in the spectra, coherence and phase, calculated via PSP and dynamic pressure sensors validated the PSP processing steps. The second part of the report describes the buffet validation process, for which the first step was to use pressure histories from all PSP points to determine the "true" force fluctuations. In the next step only a selected number of pixels were chosen as "virtual sensors" and a correlation-length based buffet calculation procedure was applied to determine "modeled" force fluctuations. By progressively decreasing the number of virtual sensors it was observed that the present calculation procedure was able to make a close estimate of the "true" unsteady forces only from four sensors. It is believed that the present work provides the first validation of the buffet calculation procedure which has been used for the development of many space vehicles.

Buffet↗
NASA NTRS2015

In-Flight Aeroelastic Stability of the Thermal Protection System on the NASA HIAD, Part II: Nonlinear Theory and Extended Aerodynamics

Conical shell theory and a supersonic potential flow aerodynamic theory are used to study the nonlinear pressure buckling and aeroelastic limit cycle behavior of the thermal protection system for NASA's Hypersonic Inflatable Aerodynamic Decelerator. The structural model of the thermal protection system consists of an orthotropic conical shell of the Donnell type, resting on several circumferential elastic supports. Classical Piston Theory is used initially for the aerodynamic pressure, but was found to be insufficient at low supersonic Mach numbers. Transform methods are applied to the convected wave equation for potential flow, and a time-dependent aerodynamic pressure correction factor is obtained. The Lagrangian of the shell system is formulated in terms of the generalized coordinates for all displacements and the Rayleigh-Ritz method is used to derive the governing differential-algebraic equations of motion. Aeroelastic limit cycle oscillations and buckling deformations are calculated in the time domain using a Runge-Kutta method in MATLAB. Three conical shell geometries were considered in the present analysis: a 3-meter diameter 70 deg. cone, a 3.7-meter 70 deg. cone, and a 6-meter diameter 70 deg. cone. The 6-meter configuration was loaded statically and the results were compared with an experimental load test of a 6-meter HIAD. Though agreement between theoretical and experimental strains was poor, the circumferential wrinkling phenomena observed during the experiments was captured by the theory and axial deformations were qualitatively similar in shape. With Piston Theory aerodynamics, the nonlinear flutter dynamic pressures of the 3-meter configuration were in agreement with the values calculated using linear theory, and the limit cycle amplitudes were generally on the order of the shell thickness. The effect of axial tension was studied for this configuration, and increasing tension was found to decrease the limit cycle amplitudes when the circumferential elastic supports were neglected, but resulted in more complex behavior when the supports were included. The nominal flutter dynamic pressure of the 3.7-meter configuration was significantly lower than that of the 3-meter, and it was found that two sets of natural modes coalesce to flutter modes near the same dynamic pressure. This resulted in a significant drop in the limit cycle frequencies at higher dynamic pressures, where the flutter mode with the lower frequency becomes more critical. Pre-buckling pressure loads and the aerodynamic pressure correction factor were studied for all geometries, and these effects resulted in significantly lower flutter boundaries compared with Piston Theory alone. The maximum dynamic pressure predicted by aerodynamic simulations of a proposed 3.7-meter HIAD vehicle was still lower than any of the calculated flutter dynamic pressures, suggesting that aeroelastic effects for this vehicle are of little concern.

Goldman, Benjamin D.↗
NASA NTRS1990

The effectiveness of vane-aileron excitation in the experimental determination of flutter speed by parameter identification

The effectiveness of aerodynamic excitation is evaluated analytically in conjunction with the experimental determination of flutter dynamic pressure by parameter identification. Existing control surfaces were used, with an additional vane located at the wingtip. The equations leading to the identification of the equations of motion were reformulated to accommodate excitation forces of aerodynamic origin. The aerodynamic coefficients of the excitation forces do not need to be known since they are determined by the identification procedure. The 12 degree-of-freedom numerical example treated in this work revealed the best wingtip vane locations, and demonstrated the effectiveness of the aileron-vane excitation system. Results from simulated data gathered at much lower dynamic pressures (approximately half the value of flutter dynamic pressure) predicted flutter dynamic pressures with 2-percent errors.

Nissim, Eli↗
NASA NTRS1990

Effects of spoiler surfaces on the aeroelastic behavior of a low-aspect-ratio rectangular wing

An experimental research study to determine the effectiveness of spoiler surfaces in suppressing flutter onset for a low-aspect-ratio, rectangular wing was conducted in the Langley Transonic Dynamics Tunnel (TDT). The wing model used in this flutter test consisted of a rigid wing mounted to the wind-tunnel wall by a flexible, rectangular beam. The flexible beam was connected to the wing root and cantilever mounted to the wind-tunnel wall. The wing had a 1.5 aspect ratio based on wing semispan and a NACA 64A010 airfoil shape. The spoiler surfaces consisted of thin, rectangular aluminum plates that were vertically mounted to the wing surface. The spoiler surface geometry and location on the wing surface were varied to determine the effects of these parameters on the classical flutter of the wing model. Subsonically, the experiment showed that spoiler surfaces increased the flutter dynamic pressure with each successive increase in spoiler height or width. This subsonic increase in flutter dynamic pressure was approximately 15 percent for the maximum height spoiler configuration and for the maximum width spoiler configuration. At transonic Mach numbers, the flutter dynamic pressure conditions were increased even more substantially than at subsonic Mach numbers for some of the smaller spoiler surfaces. But greater than a certain spoiler size (in terms of either height or width) the spoilers forced a torsional instability in the transonic regime that was highly Mach number dependent. This detrimental torsional instability was found at dynamic pressures well below the expected flutter conditions. Variations in the spanwise location of the spoiler surfaces on the wing showed little effect on flutter. Flutter analysis was conducted for the basic configuration (clean wing with all spoiler surface mass properties included). The analysis correlated well with the clean wing experimental flutter results.

Cole, Stanley R.↗
NASA NTRS1979

Experimental study of acoustic loads on an upper-surface-blown STOL airplane configuration

Fluctuating pressure levels were measured on the flap and fuselage of an upper-surface-blown jet-flap airplane configuration in a wind tunnel. The model tested had turbofan engines with a bypass ratio of 3 and a thrust rating of 10 kN. Rectangular nozzles were mounted flush with the upper surface at 35 percent of the wing chord. Test parameters were flap deflection angle, jet impingement angle, angle of attack, free-stream velocity, spanwise location of the engine, and jet dynamic pressure. Load levels were high throughout the jet impingement region, with the highest levels (about 159 dB) occurring on the fuselage and near the knee of the flap. The magnitude of the forward-velocity effect appeared to depend upon the ratio of free-stream and jet velocities. Good agreement was obtained between fluctuating pressure spectra measured at jet dynamic pressures of 7 and 22 kPa when the spectra were scaled by nondimensional functions of dynamic pressure, velocity, and the empirical relationship between dynamic pressure and overall fluctuating pressure level.

Willis, C. M.↗