Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Cu”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Cryostatic influence of formvar coatings on sizing of the stabilizer in composite NbTi-Cu superconductors

Often undesirable low energy densities are associated with extreme safety measures (e.g. cryostatic stability) in large superconducting magnets. Therefore, a medium-sized, formvar-coated composite NbTi alloy, Cu-stabilized, has been studied (48 filaments, approximately square cross section about 1/5 cm thickness). Thermal quench behavior (caused by heating) was investigated in various fluid states of He4, including pressurized and superfluid He4. The data obtained support existence of a particular coating thickness ('limiting' thickness) with the property that thermal boundary conditions of uncoated superconductors at a quench are not deteriorated.

Caspi, S.↗
NASA NTRS1981

Intraband optical conductivity sigma/omega,T/ of Cu, Ag, and Au - Contribution from electron-electron scattering

The frequency and temperature dependence of the intraband optical conductivity of the noble metals Cu, Ag and Au is measured and contributions of electron-electron scattering are assessed. Optical measurements were performed at temperatures of 77, 295 and 425 K to obtain values of the Drude electron scattering rate with a linear dependence on temperature which may be attributed to electron-phonon scattering, and a quadratic dependence on photon energy, which is suggestive of electron-electron scattering but is a factor of two to three times greater than would be expected. Comparison of the optical data with dc electrical and thermal resistivity data which also show behavior attributed to electron-electron scattering reveals discrepancies of up to an order of magnitude. Other possible mechanisms for the frequency dependence, including absorptance, electron-surface plasmon interactions, a two-carrier model, and a structure dependence are considered, and it is concluded that the frequency dependence in the Drude scattering rates of the noble metals is not yet quantitatively understood

Parkins, G. R.↗
NASA NTRS1983

Transmission electron microscopy characterization of microstructural features of Al-Li-Cu alloys

A transmission electron microscopy (TEM) examination of aluminum-lithium-copper alloys was conducted. The principal purpose is to characterize the nature, size, and distribution of stringer particles which result from the powder metallurgy (P/M) processing of these alloys. Microstructural features associated with the stringer particles are reported that help explain the stress corrosion susceptibility of the powder metallurgy-processed Al-Li-Cu alloys. In addition, matrix precipitation events are documented for a variety of heat treatments and process variations. Hot rolling is observed to significant alter the nature of matrix precipitation, and the observations are correlated with concomitant mechanical property variations.

Avalos-Borja, M.↗
NASA NTRS1983

A surface analytical examination of Stringer particles in Al-Li-Cu alloys

A surface analytical examination of powder metallurgy processed Al-Li-Cu alloys was conducted. The oxide stringer particles often found in these alloys was characterized. Particle characterization is important to more fully understand their impact on the stress corrosion and fracture properties of the alloy. The techniques used were SIMS (Secondary Ion Mass Spectroscopy) and SAM (Scanning Auger Microscopy). The results indicate that the oxide stringer particles contain both Al and Li with relatively high Li content and the Li compounds may be associated with the stringer particles, thereby locally depleting the adjacent matrix of Li solute.

Larson, L. A.↗
NASA NTRS1984

Models for the Effects of G-seat Cuing on Roll-axis Tracking Performance

Including whole-body motion in a flight simulator improves performance for a variety of tasks requiring a pilot to compensate for the effects of unexpected disturbances. A possible mechanism for this improvement is that whole-body motion provides high derivative vehicle state information whic allows the pilot to generate more lead in responding to the external disturbances. During development of motion simulating algorithms for an advanced g-cuing system it was discovered that an algorithm based on aircraft roll acceleration producted little or no performance improvement. On the other hand, algorithms based on roll position or roll velocity produced performance equivalent to whole-body motion. The analysis and modeling conducted at both the sensory system and manual control performance levels to explain the above results are described.

Levison, W. H.↗
NASA NTRS1985

Reversion phenomena of Cu-Cr alloys

Cu-Cr alloys which were given various aging and reversion treatments were investigated in terms of electrical resistivity and hardness. Transmission electron microscopy was one technique employed. Some results obtained are as follows: the increment of electrical resistivity after the reversion at a constant temperature decreases as the aging temperature rises. In a constant aging condition, the increment of electrical resistivity after the reversion increases, and the time required for a maximum reversion becomes shorter as the reversion temperature rises. The reversion phenomena can be repeated, but its amount decreases rapidly by repetition. At first, the amount of reversion increases with aging time and reaches its maximum, and then tends to decrease again. Hardness changes by the reversion are very small, but the hardness tends to soften slightly. Any changes in transmission electron micrographs by the reversion treatment cannot be detected.

Nishikawa, S.↗
NASA NTRS1984

Pilot differences and motion cuing effects on simulated helicopter hover

The effects that cues of aircraft motion, delays in visual scene, and movement of a ship model have on pilots' ability to hover a simulated helicopter near a destroyer-class ship were examined. Twelve pilots were tested in a within-subject factorial combination of fixed-base, moving-base, and G-seat conditions in which delays of 66 or 128 ms existed in the simulator's visual display and the pilots had to hover near a moving or stationary ship. Best control performance was seen under the moving-base conditions, whereas poorest control was associated with the fixed-base simulation. An intermediate level of performance was produced by the G-seat. In addition, visual delay affected control of the roll axis of the simulation, and interactions between pilots and motion cuing and visual delay were seen. Movement of the ship model had little effect.

Ricard, G. L.↗
NASA NTRS1984

The physical metallurgy of mechanically-alloyed, dispersion-strengthened Al-Li-Mg and Al-Li-Cu alloys

Powder processing of Al-Li-Mg and Al-Li-Cu alloys by mechanical alloying (MA) is described, with a discussion of physical and mechanical properties of early experimental alloys of these compositions. The experimental samples were mechanically alloyed in a Szegvari attritor, extruded at 343 and 427 C, and some were solution-treated at 520 and 566 C and naturally, as well as artificially, aged at 170, 190, and 210 C for times of up to 1000 hours. All alloys exhibited maximum hardness after being aged at 170 C; lower hardness corresponds to the solution treatment at 566 C than to that at 520 C. A comparison with ingot metallurgy alloys of the same composition shows the MA material to be stronger and more ductile. It is also noted that properly aged MA alloys can develop a better combination of yield strength and notched toughness at lower alloying levels.

Gilman, P. S.↗
NASA NTRS1985

ac susceptibility of thermally annealed and neutron irradiated Cu-Ni alloys

Thermal annealing and high-flux neutron irradiation are used to vary the degree of short-range atomic order in Cu-Ni alloys of composition 40, 50, and 60 at. pct Ni. The magnetic state is measured by ac magnetic susceptibility measurements. It is shown that annealing at 350 C causes significant changes in the susceptibility of all the samples. In the 50 and 60 at. pct Ni samples, the transition is broadened and extended to higher temperatures, while the 40 at. pct Ni sample changes from a paramagnetic system to a weakly ferromagnetic system. The neutron irradiation, in contrast to the thermal treatment, causes the development of smaller size cluster formations. The irradiated 60 at. pct Ni sample exhibits no change in the shape of its susceptibility curve from that of the quenched sample, whereas, the 40 pct alloy is changed, by irradiation, from a paramagnetic system to a spin-glass system.

Catchings, R. M., III↗
NASA NTRS1984

The nature of chemisorbed oxygen on Ni(100) and Cu(100)

Model calculations indicate two low-lying states for the interaction of O with Ni and Cu(100). The oxide state is approximately 1 eV more stable and its R(perpendicular) for Ni(100) is consistent with the experimental value for Ni(100), indicating only one type of stable chemisorption bond. This agrees with XPS (X-ray photoemission spectroscopy) and EXAFS (extended X-ray absorption fine structure) data for the observed LEED (low energy electron diffraction) structures. Interpretations of EELS (electron energy loss spectroscopy) data in terms of a radical state forthe p(2x2) and the oxide state for the c(2x2) structure must be seriously questioned.

Bauschlicher, C. W., Jr.↗
NASA NTRS1986

An evaluation of the benefits of utilizing rapid solidification for development of 2XXX (Al-Cu-Mg) alloys

The advantages of rapid solidification processing over ingot metallurgy processing in the development of 2XXX aluminum alloy compositions were evaluated using a similarly processed ingot metallurgy (IM) control alloy. The powder metallurgy (PM) alloy extrusions showed a reduced age-hardening response in comparison with similar IM compositions, with higher tensile properties for naturally aged extrusions but lower properties for artificially aged ones. However, the tensile properties of naturally and artificially aged PM alloy extrusions based on a version of IM 2034 alloy, but containing 0.6 weight percent zirconium, were comparable to those of the IM control extrusions and had significantly superior combinations of strength and toughness. The tensile properties of this PM alloy showed even greater advantage in 6.4-mm (0.25-in.) and 1.8-mm (0.070-in.) plate and sheet, the yield strength being about 68 MPa (10 ksi) greater than reported values for the IM 2034 alloy sheet. An artificially aged PM alloy based on 2219 alloy also showed a strength and strength-toughness combination comparable to those of the PM Al-Cu-Mg-Zr alloy, substantially outperforming the IM 2219 alloy. These results show that rapid solidification offers the flexibility needed to modify conventional IM compositions to produce new alloy compositions with superior mechanical properties.

Paris, H. G.↗
NASA NTRS1987

Evidence for superconductivity above 40 K in the La-Ba-Cu-O compound system

An apparent superconducting transition with an onset temperature above 40 K has been detected under pressure in the La-Ba-Cu-O compound system synthesized directly from a solid-state reaction of La2O3, CuO, and BaCO3 followed by a decomposition of the mixture in a reduced atmosphere. The experiment is described and the results of effects of magnetic field and pressure are discussed.

Chu, C. W.↗
NASA NTRS1987

Superconductivity at 93 K in a new mixed-phase Y-Ba-Cu-O compound system at ambient pressure

A stable and reproducible superconductivity transition between 80 and 93 K has been achieved and maintained in a Y-Ba-Cu-O compound system at ambient pressure in a simple liquid-nitrogen Dewar. An upper critical field Hc2(0) estimate of between 80 and 180 T is obtained, and the paramagnetic limiting field at 0 K for a sample with a T(c) of about 90 K is 165 T. It is suggested that the lattice parameters, the valence ratio, and the sample treatments all play a role in achieving superconductivity above 77 K.

Wu, M. K.↗
NASA NTRS1987

A thermodynamic prediction for microporosity formation in aluminum-rich Al-Cu alloys

A computer model is used to predict the formation and degree of microporosity in a directionally solidified Al-4.5 wt pct Cu alloy, considering the interplay between solidification shrinkage and gas porosity. Macrosegregation theory is used to determine the local pressure within the interdendritic liquid. Results show interdendritic porosity for initial hydrogen contents in the 0.03-1 ppm range, and none below contents of 0.03. An increase in either the thermal gradient or the solidification rate is show to decrease the amount of interdendritic porosity.

Poirier, D. R.↗
NASA NTRS1988

Theoretical study of the electron affinities of Cu, Cu2, and Cu3

The modified pair functional method is used here to compute the electron affinities of the negative ions of Cu, Cu2, and Cu3 to equal relative accuracy. The results show that, while the extra electron in Cu2(-) occupies a sigma(u) antibonding orbital, the orbital is polarized to reduce the density in the internuclear rergion. The calculations also show that Cu3(-) is a closed-shell linear molecule in its ground state, and that there is an excited triplet state about 0.7 eV higher in energy. This strongly suggests that photodetachment from the excited triplet state is responsible for the low energy structure observed in the photoelectron spectrum of Cu3(-).

Bauschlicher, Charles W., Jr.↗
NASA NTRS1988

Superconductivity up to 114 K in the Bi-Al-Ca-Sr-Cu-O compound system without rare-earth elements

Stable superconductivity up to 114 K has been reproducibly detected in Bi-Al-Ca-Sr-Cu-O multiphase systems without any rare-earth elements. Pressure has only a slight positive effect on T(c). These observations provide an extra material base for the study of the mechanism of high-temperature superconductivity and also the prospect of reduced material cost for future applications of superconductivity.

Chu, C. W.↗
NASA NTRS1988

Superconductivity in the high-Tc Bi-Ca-Sr-Cu-O system - Phase identification

Four phases are observed in superconducting Bi-Ca-Sr-Cu-O samples. The superconducting phase, with onset temperature near 120 K, is a 15.4-A-layered compound with composition near Bi2Ca1Sr2Cu2O9 and an A-centered orthorhombic unit subcell 5.41 x 5.44 x 30.78 A. X-ray diffraction and electron microscopy data are consistent with a structure of alternating perovskite and Bi2O2 layers. High-resolution transmission electron microscopy images reveal a b-axis superstructure of 27.2 A, numerous (001) stacking faults, and other defects.

Hazen, R. M.↗
NASA NTRS1988

Crystallography, chemistry and structural disorder in the new high-Tc Bi-Ca-Sr-Cu-O superconductor

Diffraction experiments are reported which indicate that the new Bi-Ca-Sr-Cu-O layer-structure superconductor possesses a primitive orthorhombic unit cell with probable space group Pnnn. The material exhibits severe structural disorder which is primarily related to stacking within the layers. The apparent orthorhombic structure is an average resulting from orthorhombic material mixed with monoclinic domains in two twinned orientations. Two distinct types of structural disorder that are common in materials synthesized to date are also described. This disorder complicates the crystallographic analysis and suggests that X-ray and neutron diffraction methods may yield only an average structure.

Veblen, D. R.↗