Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Contact Forces”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

Energy-Absorbing, Lightweight Wheels

Improved energy-absorbing wheels are under development for use on special-purpose vehicles that must traverse rough terrain under conditions (e.g., extreme cold) in which rubber pneumatic tires would fail. The designs of these wheels differ from those of prior non-pneumatic energy-absorbing wheels in ways that result in lighter weights and more effective reduction of stresses generated by ground/wheel contact forces. These wheels could be made of metals and/or composite materials to withstand the expected extreme operating conditions. As shown in the figure, a wheel according to this concept would include an isogrid tire connected to a hub via spring rods. The isogrid tire would be a stiff, lightweight structure typically made of aluminum. The isogrid aspect of the structure would both impart stiffness and act as a traction surface. The hub would be a thin-walled body of revolution having a simple or compound conical or other shape chosen for structural efficiency. The spring rods would absorb energy and partially isolate the hub and the supported vehicle from impact loads. The general spring-rod configuration shown in the figure was chosen because it would distribute contact and impact loads nearly evenly around the periphery of the hub, thereby helping to protect the hub against damage that would otherwise be caused by large loads concentrated onto small portions of the hub.

Waydo, Peter↗

Acoustically induced slip in sheared granular layers: Application to dynamic earthquake triggering: TRIGGERED SLIP IN SHEARED GRANULAR GOUGE

A fundamental mystery in earthquake physics is “how can an earthquake be triggered by distant seismic sources?” We use discrete element method simulations of a granular layer, during stick slip, that is subject to transient vibrational excitation to gain further insight into the physics of dynamic earthquake triggering. We also observe delayed triggering of slip in the granular gouge, using Coulomb friction law for grains interaction. We find that at a critical vibrational amplitude (strain) there is an abrupt transition from negligible time-advanced slip (clock advance) to full clock advance; i.e., transient vibration and triggered slip are simultaneous. Moreover, the critical strain is of order 10 -6 , similar to observations in the laboratory and in Earth. The transition is related to frictional weakening of the granular layer due to a dramatic decrease in coordination number and the weakening of the contact force network. Associated with this frictional weakening is a pronounced decrease in the elastic modulus of the layer. The study has important implications for mechanisms of triggered earthquakes and induced seismic events and points out the underlying processes in response of the fault gouge to dynamic transient stresses.

58 GEOSCIENCES↗

Dynamic simulation of powder packing structure for powder bed additive manufacturing

Here, powder packing structure is a critical parameter of powder bed-based additive manufacturing (AM). Experimental characterization of powder is typically limited to measuring bulk properties, whereas many numerical models of AM powder packing are based on geometrical consideration without accounting for particle-to-particle interactions. In the present paper, the powder packing dynamics is simulated using a discrete element method (DEM)-based model that solves the mechanical contact forces and moments between individual particles. As DEM uses explicit time integration, a main challenge in modeling dynamics of metallic powder packing is the need for extremely fine time increment size (e.g., in the order of 1 ns for a 10-μm-diameter particle). The effect of mass scaling, employed for speeding up the calculation, on the simulation results is examined in a test case of powder particles packed inside a box container. The calculated packing density for two different particle size distributions is validated against independent literature data for laser powder bed AM with AISI 316L stainless steel powder. The sensitivity of key input parameters (e.g., friction coefficient) is further evaluated in this test case. The powder packing model is then applied to a practical situation of binder jet AM involving rolling of multiple layers of IN718 powder particles onto a powder bed, for which the calculated packing density is also validated with independent literature data.

42 ENGINEERING↗

Discrete element modelling of flexible membrane boundaries for triaxial tests

The discrete element modelling of triaxial tests plays a critical role in unveiling fundamental properties of particulate materials, but the numerical implementation of a flexible membrane boundary for the testing still imposes problems. Here, in this work, a robust algorithm was proposed to reproduce a flexible membrane boundary in triaxial testing. The equivalence of strain energy enables the particle-scale parameters representing the flexible membrane to be directly determined from the real geometric and material parameters of the membrane. Then the proposed flexible membrane boundary was implemented in the context of discrete element simulation of triaxial testing and was validated with laboratory experiments. Furthermore, comparisons of triaxial tests with flexible and rigid boundaries were performed from macro-scale to meso-scale. Lastly, the results show that the boundary condition has limited influences on the stress-strain behaviour but a relatively large impact on the volumetric change, the failure mode, the distribution of contact forces, and the fabric evolution of particles in the specimen during triaxial testing.

42 ENGINEERING↗

Survey of Dust Production in Pebble Bed Reactors Cores

Graphite dust produced via mechanical wear from the pebbles in a pebble bed reactor is an area of concern for licensing. Both the German pebble bed reactors produced graphite dust that contained activated elements. These activation products constitute an additional source term of radiation and must be taken under consideration during the conduct of accident analysis of the design. This paper discusses the available literature on graphite dust production and measurements in pebble bed reactors. Limited data is available on the graphite dust produced from the AVR and THTR-300 pebble bed reactors. Experiments that have been performed on wear of graphite in pebble-bed-like conditions are reviewed. The calculation of contact forces, which are a key driving mechanism for dust in the reactor, are also included. In addition, prior graphite dust predictions are examined, and future areas of research are identified.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Effect of grain dissolution on sloping ground

The static and dynamic stability of natural or constructed slopes can be affected by dissolution or dissolution-like phenomena. Their underlying mechanisms, however, remain unclear. New experimental results and discrete element simulations provide particle-level and macroscale information on the consequences of mineral dissolution on slope behavior. At the microscale, load-carrying grain arches develop around dissolving particles, the porosity increases, and contact force chains evolve to form a honeycomb topology. At the macroscale, while vertical settlements are the prevailing deformation pattern, lateral granular movements that create mass wasting are prominent in sloping ground, even under the quasi-static granular loss. Horizontal grain displacement is maximum at the surface and decreases linearly with the distance from the slope surface to become zero at the bottom boundaries, much like vertical granular displacement along the depth. Sediments with smaller friction angles and steeper slopes experience greater displacement, both vertically and horizontally. Slopes become flatter after dissolution, with the reduction in slope angle directly related to the loss in ground elevation, ΔH/H o . Yet, because of the porous fabric that results from dissolution, vertical shortening is less than the upper bound, estimated from the loss in the solid mass fraction, ΔH/H o ≈SF. Under water-saturated conditions, the post-dissolution fabric may lead to sudden undrained shear and slope slide.

42 ENGINEERING↗

Design of robot grippers for binder jet products handling

Dimension accuracy, damage minimization, and defect detection are essential in manufacturing processes, especially additive manufacturing. These types of challenges may arise either during the manufacture of a product or its use. The repeatability of the process is vital in additive manufacturing systems. However, human users may lose concentration and, thus, would be a great alternative as an assistant. Depending on the nature of work, a robot’s fingers might vary, for example, mechanical, electrical, vacuum, two-fingers, and three-fingers. In addition, the end effector plays a vital role in picking up an object in the advanced manufacturing process. However, inbuilt robotic fingers may not be appropriate in different production environments. In this research presented here considering metal binder jet additive manufacturing, the two-finger end- effectors are proposed design, analysis, and experiment to pick up an object after completing the production process from a specific location. The final designs were further printed by using a 3D metal printer and installed in the existing robotic systems. These new designs are used successfully to hold the object from the specific location by reducing the contact force that was not possible with the previously installed end effector's finger. In addition, a numerical study was conducted in order to compare the flowability of the geometric shape of finger's free areas.

42 ENGINEERING↗

IDENTIFYING FRACTURE ORIGIN IN CERAMICS BY COMBINATION OF NONDESTRUCTIVE TESTING AND DISCRETE ELEMENT ANALYSIS

Advanced ceramic materials have been extensively applied in aerospace, automobile and other industries. However, the reliability of the advanced ceramics is a major concern because of the brittle nature of the materials. In this paper, combination of nondestructive testing and numerical modeling Discrete Element Method is proposed to identify the fracture origin in ceramics. The nondestructive testing--laser scattering technology is first performed on the ceramic components to reveal the machining-induced damage such as cracks and the material-inherent flaws such as voids, then followed by the four point bending test. Discrete Element software package PFC{sup 2D} is used to simulate the four point bending test and try to identify where the fractures start. The numerical representation of the ceramic materials is done by generating a densely packed particle system using the specimen genesis procedure and then applying the suitable microparameters to the particle system. Simulation of four point bending test is performed on materials having no defects, materials having manufacturing-induced defects like cracks, and materials having material-inherent flaws like voids. The initiation and propagation of defects is modeled and the mean contact force on the loading ball is also plotted. The simulation prediction results are well in accordance with the nondestructive testing results.

36 MATERIALS SCIENCE↗

Effects of Prosthesis Stem Tapers on Stress Distribution of Cemented Hip Arthroplasty

Aseptic loosening effects are critical issues in encouraging long term stability of cemented hip arthroplasty. Stress shielding is believed to be an important factor that contributes to the aseptic loosening problems. The numerous changes in the prosthesis stem design are intended to minimize the stress shielding and aseptic loosening problems and to improve the long term performance of the implants. In this study, the stress distribution in cemented hip arthroplasty is established using finite element method. The taper of the prosthesis is designed to be 3 deg. at anterior/posterior, 3 deg. at medial/lateral and 10 deg. from wide lateral to narrow medial. Major muscle loads and contact forces are simulated for walking (toe-off phase) and stair climbing load cases. Effects of prosthesis stem tapers on the resulting stress distribution are investigated. Results show that compressive stress dominates in the medial plane while tensile stress in the lateral plane of the femur. The corresponding stress levels of intact femur for walking and stair-climbing load cases are 22 and 29 MPa, respectively. The magnitude of Tresca stress for the THA femur in stair-climbing load case remains higher in the region of 85 MPa while the walking load case induces around 40 MPa. The stress range in the straight and single taper stem prosthesis is lower than 260 MPa, while localized Tresca stress is in the order of the yield strength of Ti-6Al-4V alloy for double and triple taper stem design.

36 MATERIALS SCIENCE↗

Scanning thermo-ionic microscopy for probing local electrochemistry at the nanoscale

Conventional electrochemical characterization techniques based on voltage and current measurements only probe faradaic and capacitive rates in aggregate. In this work we develop a scanning thermo-ionic microscopy (STIM) to probe local electrochemistry at the nanoscale, based on imaging of Vegard strain induced by thermal oscillation. It is demonstrated from both theoretical analysis and experimental validation that the second harmonic response of thermally induced cantilever vibration, associated with thermal expansion, is present in all solids, whereas the fourth harmonic response, caused by local transport of mobile species, is only present in ionic materials. The origin of STIM response is further confirmed by its reduced amplitude with respect to increased contact force, due to the coupling of stress to concentration of ionic species and/or electronic defects. The technique has been applied to probe Sm-doped Ceria and LiFePO{sub 4}, both of which exhibit higher concentrations of mobile species near grain boundaries. The STIM gives us a powerful method to study local electrochemistry with high sensitivity and spatial resolution for a wide range of ionic systems, as well as ability to map local thermomechanical response.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Superconducting qubits in a flip-chip architecture

Flip-chip architectures have recently enabled significant scaling-up of multi-qubit circuits and have been used to assemble hybrid quantum systems that combine different substrates, for example, for quantum acoustics experiments. The standard flip-chip method uses superconducting galvanic connections between two substrates, typically implemented using sophisticated indium wafer-bonding systems, which give highly reliable and temperature-cyclable assemblies, but are expensive, somewhat inflexible in design, and require robust substrates that can sustain the large compressive forces required to cold-weld the indium bonds. A much simpler method is to assemble dies using very low-force contacts and air-dried adhesives, although this does not provide a galvanic contact between the dies. In this work, we demonstrate that the latter technique can be used to reliably couple superconducting qubit circuits, in which the qubits are on separate dies, without the need for a galvanic connection. We demonstrate full vector qubit control of each qubit on each of the two dies, with high-fidelity single-shot readout, and further demonstrate entanglement-generating excitation swaps as well as benchmark a controlled-Z entangling gate between the two qubits on the two dies. This exemplifies a simple and inexpensive assembly method for two-plus-one-dimensional quantum circuit integration that supports the use of delicate or unusually shaped substrates.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

A constitutive model for sheared dense fiber suspensions

Here we propose a constitutive model to predict the viscosity of fiber suspensions, which undergoes shear thinning, at various volume fractions, aspect ratios, and shear stresses/rates. We calibrate the model using the data from direct numerical simulation and prove the accuracy by predicting experimental measurements from the literature. We use a friction coefficient decreasing with the normal load between the fibers to quantitatively reproduce the experimentally observed shear thinning in fiber suspensions. In this model, the effective normal contact force, which is directly proportional to the bulk shear stress, determines the effective friction coefficient. A rise in the shear stress reduces the effective friction coefficient in the suspension. As a result, the jamming volume fraction increases with the shear stress, resulting in a shear thinning in the suspension viscosity. Moreover, we extend the model to quantify the effects of fiber volume fraction and aspect ratio in the suspension. We calibrate this model using the data from numerical simulations for the rate-controlled shear flow. Once calibrated, we show that the model can be used to predict the relative viscosity for different volume fractions, shear stresses, and aspect ratios. The model predictions are in excellent agreement with the available experimental measurements from the literature. The findings of this study can potentially be used to tune the fiber size and volume fraction for designing the suspension rheology in various applications.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Rotation-dependent catastrophic disruption of gravitational aggregates

We carry out a systematic exploration of the effect of pre-impact rotation on the outcomes of low-speed collisions between planetesimals modeled as gravitational aggregates. We use pkdgrav, a cosmology code adapted to collisional problems and recently enhanced with a new soft-sphere collision algorithm that includes more realistic contact forces. A rotating body has lower effective surface gravity than a non-rotating one and therefore might suffer more mass loss as the result of a collision. What is less well understood, however, is whether rotation systematically increases mass loss on average regardless of the impact trajectory. This has important implications for the efficiency of planet formation via planetesimal growth, and also more generally for the determination of the impact energy threshold for catastrophic disruption (leading to the largest remnant retaining 50% of the original mass), as this has generally only been evaluated for non-spinning bodies. We find that for most collision scenarios, rotation lowers the threshold energy for catastrophic dispersal. For head-on collisions, we develop a semi-analytic description of the change in the threshold description as a function of the target's pre-impact rotation rate, and find that these results are consistent with the 'universal law' of catastrophic disruption developed by Leinhardt and Stewart. Using this approach, we introduce re-scaled catastrophic disruption variables that take into account the interacting mass fraction of the target and the projectile in order to translate oblique impacts into equivalent head-on collisions.

79 ASTRONOMY AND ASTROPHYSICS↗

Universal corrections to the superfluid gap in a cold Fermi gas

A framework for computing the superfluid gap in an effective field theory (EFT) of fermions interacting via momentum-independent contact forces is developed. The leading universal corrections in the EFT are one-loop in-medium effects at the Fermi surface, and reproduce the well-known Gor'kov-Melik-Barkhudarov result. Here, the complete subleading universal corrections are presented here, and include one-loop effects away from the Fermi surface, two-loop in-medium effects, as well as modifications to the fermion propagator. Together, these effects are found to reduce the gap at low densities. Applications to neutron superfluidity in neutron stars are also discussed.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Edwards statistical mechanics for jammed granular matter

In 1989, Sir Sam Edwards made the visionary proposition to treat jammed granular materials using a volume ensemble of equiprobable jammed states in analogy to thermal equilibrium statistical mechanics, despite their inherent athermal features. Since then, the statistical mechanics approach for jammed matter—one of the very few generalizations of Gibbs-Boltzmann statistical mechanics to out-of-equilibrium matter—has garnered an extraordinary amount of attention by both theorists and experimentalists. Its importance stems from the fact that jammed states of matter are ubiquitous in nature appearing in a broad range of granular and soft materials such as colloids, emulsions, glasses, and biomatter. Indeed, despite being one of the simplest states of matter—primarily governed by the steric interactions between the constitutive particles—a theoretical understanding based on first principles has proved exceedingly challenging. Here a systematic approach to jammed matter based on the Edwards statistical mechanical ensemble is reviewed. The construction of microcanonical and canonical ensembles based on the volume function, which replaces the Hamiltonian in jammed systems, is discussed. The importance of approximation schemes at various levels is emphasized leading to quantitative predictions for ensemble averaged quantities such as packing fractions and contact force distributions. An overview of the phenomenology of jammed states and experiments, simulations, and theoretical models scrutinizing the strong assumptions underlying Edwards approach is given including recent results suggesting the validity of Edwards ergodic hypothesis for jammed states. A theoretical framework for packings whose constitutive particles range from spherical to nonspherical shapes such as dimers, polymers, ellipsoids, spherocylinders or tetrahedra, hard and soft, frictional, frictionless and adhesive, monodisperse, and polydisperse particles in any dimensions is discussed providing insight into a unifying phase diagram for all jammed matter. Furthermore, the connection between the Edwards ensemble of metastable jammed states and metastability in spin glasses is established. This highlights the fact that the packing problem can be understood as a constraint satisfaction problem for excluded volume and force and torque balance leading to a unifying framework between the Edwards ensemble of equiprobable jammed states and out-of-equilibrium spin glasses.

97 MATHEMATICS AND COMPUTING↗

A constitutive model for sheared dense suspensions of rough particles

In a concentrated suspension, particles come into contact due to the presence of asperities on their surfaces. As a result, the contact forces and interparticle friction become one of the important factors governing the rheology of rigid particle suspensions at high concentrations. We show that a load-dependent friction model can be used to reproduce the experimentally observed shear thickening [ST—continuous and discontinuous (DST)] behavior with an increase in the asperity size. Increasing the particle surface roughness size leads to a decrease in the critical shear rate above which shear-thickening takes place, a reduction in the critical volume fraction for DST and an increase in the viscosity jump across non-shear-thickened to shear-thickened regime. In this paper, we propose a constitutive model to quantify the effect of increasing the roughness size on the rheology of dense ST suspensions as well as on the critical shear rate for ST and the critical volume fraction for DST. We fit this model to our simulation data for stress controlled shear flow of dense rough particle suspensions. Once the fitting is complete, these equations are used to predict exact volume fractions and shear stress values for transitions between three regimes on the shear stress-shear rate flow state diagram for different roughness values. Furthermore, the results of this study can be used to tune the particle surface roughness for manipulating the dense suspension rheology according to different applications.

42 ENGINEERING↗

CFD-DEM Onset of Motion Analysis for Application to Bed Scour Risk Assessment

This CFD study with DEM was done as a part of the Federal Highway Administration’s (FHWA’s) effort to improve scour design procedures. The Computational Fluid Dynamics-Discrete Element Method (CFD-DEM) model, available in CD-Adapco’s StarCCM+ software, was used to simulate multiphase systems, mainly those which combine fluids and solids. In this method the motion of discrete solids is accounted for by DEM, which applies Newton's laws of motion to every particle. The flow of the fluid is determined by the local averaged Navier–Stokes equations that can be solved using the traditional CFD approach. The interactions between the fluid phase and solids phase are modeled by use of Newton's third law. The inter-particle contact forces are included in the equations of motion. Soft-particle formulation is used, which allows particles to overlap. In this study DEM was used to model separate sediment grains and spherical particles laying on the bed with the aim to analyze their movement due to flow conditions. Critical shear stress causing the incipient movement of the sediment was established and compared to the available experimental data. An example of scour around a cylindrical pier is considered. Various depths of the scoured bed and flow conditions were taken into account to gain a better understanding of the erosion forces existing around bridge foundations. The decay of these forces with increasing scour depth was quantified with a ‘decay function’, which shows that particles become increasingly less likely to be set in motion by flow forces as a scour hole increases in depth. Computational and experimental examples of the scoured bed around a cylindrical pier are presented.

97 MATHEMATICS AND COMPUTING↗