Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Carbon support”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Development of sulfonated carbon-based solid-acid catalysts derived from biorefinery residues and biomass ash for xylan hydrolysis

In this study, biorefinery residues and biomass ash were used to develop sulfonated carbon-based solid-acid catalysts to enhance xylan hydrolysis. Here, metals extracted from the biomass ash were impregnated into a carbon support prepared from biorefinery residues to synthesize sulfonated ash-impregnated carbon-based catalyst. Metals present in the ash most probably are responsible for the increased acid density in the catalyst. Using this catalyst, 11.4 % xylose yield was produced, an increase of 171 % over the yield obtained from a catalyst without ash impregnation. Using a xylan-to-catalyst ratio of 1:2, 72.9 % xylose yield was obtained, comparable to using 0.5 wt% sulfuric acid under the same reaction condition. Moreover, this catalyst significantly inhibited xylose dehydration, only forming 11.3 % furfural compared to that generated using dilute acid. Hence, these results show the potential for using biomass ash as a metal source to increase the number of acid sites in solid-acid catalysts used for biomass pretreatment.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Surface oxygenation induced strong interaction between Pd catalyst and functional support for zinc–air batteries

Employing the strong metal-support interaction (SMSI) effect for promoting the catalyst's activity toward the oxygen reduction reaction (ORR) is promising due to the electronic structure optimization and high utilization efficiency of platinum group metal (PGM) catalysts. Metal oxides as alternative supports for PGMs facilitate intrinsic activity and improve durability as compared to conventional carbon supports. However, the restricted mass and electron transfer at the metal/support interface need to be addressed. Herein, to strengthen the interaction at the metal/support interfaces and improve the utilization efficiency of PGM, an ultralow loading of Pd was embedded in a surface-oxygenated PdNiMnO porous film. The Mn-doping was designed to promote surface oxygenation using a facile anodization process that created sufficiently exposed interfaces between Pd and the support, strengthening the SMSI effects at the Pd/oxygenated support interface for enhancing ORR performance. Furthermore, the Ni-containing oxygenated catalyst served as both the active component for the oxygen evolution reaction (OER) and the functional support for stabilizing Pd, making PdNiMnO a bifunctional catalyst for zinc–air flow batteries (ZAFB). As a proof-of-concept, the ZAFB (PdNiMnO) shows a maximal power density of 211.6 mW cm –2 and outstanding cycling stability for over 2000 h with a minimal voltage gap of 0.69 V at a current density of 10 mA cm –2 , superior to the state-of-the-art catalysts.

25 ENERGY STORAGE↗
DOE OSTI2020

Atomically Dispersed Iron–Nitrogen Sites on Hierarchically Mesoporous Carbon Nanotube and Graphene Nanoribbon Networks for CO 2 Reduction

Atomically dispersed metal and nitrogen co-doped carbon (M-N/C) catalysts hold great promise for electrochemical CO 2 conversion. However, there is a lack of cost-effective synthesis approaches to meet the goal of economic mass production of single-atom M-N/C with desirable carbon support architecture for efficient CO 2 reduction. Herein, we report facile transformation of commercial carbon nanotube (CNT) into isolated Fe-N 4 sites anchored on carbon nanotube and graphene nanoribbon (GNR) networks (Fe-N/CNT@GNR). The oxidization-induced partial unzipping of CNT results in the generation of GNR nanolayers attached to the remaining fibrous CNT frameworks, which reticulates a hierarchically mesoporous complex and thus enables a high electrochemical active surface area and smooth mass transport. The Fe residues originating from CNT growth seeds serve as Fe sources to form isolated Fe-N-4 moieties located at the CNT and GNR basal plane and edges with high intrinsic capability of activating CO 2 and suppressing hydrogen evolution. The Fe-N/CNT@GNR delivers a stable CO Faradaic efficiency of 96% with a partial current density of 22.6 mA cm -2 at a low overpotential of 650 mV, making it one of the most active M-N/C catalysts reported. This work presents an effective strategy to fabricate advanced atomistic catalysts and highlights the key roles of support architecture in single-atom electrocatalysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Engineered Catalyst Support with Improved Durability at Higher Weight Percentage of Platinum

Proton Exchange Membrane (PEM) fuel cells are a suitable electrochemical power source for heavy duty vehicle (HDV) applications due to their high efficiency and durability. The cathode of the fuel cell uses a higher geometric loading of platinum (∼0.2 to 0.4 mg Pt /cm 2 ) for the electrocatalysis of the kinetically sluggish Oxygen Reduction Reaction (ORR) which requires higher weight percent loading of the metal (∼50%) on the carbon support to decrease the catalyst layer thickness and hence, the reactant transport losses. The conventionally used supports for platinum catalyst, such as the KetjenBlack TM type high surface area carbon (HSC) features limited mesopore area for the dispersion of Pt nanoparticles leading to increased aggregation and poor durability. Here, we show a new class of carbon materials known as the Engineered Catalyst Support (ECS) developed by Pajarito Powder with higher mesopore fraction for the dispersion of higher weight percentage of Pt nanoparticles. ECS materials can disperse up to 50% Pt by weight of the catalyst thereby enabling lower catalyst layer thickness with higher performance retained after durability test. A comprehensive set of physico-chemical and electrochemical studies in membrane electrode assembly (MEA) are reported to understand the performance and durability of Pt/ECS catalysts.

08 HYDROGEN↗
DOE OSTI2020

Modeling suggests fossil fuel emissions have been driving increased land carbon uptake since the turn of the 20th Century

Terrestrial vegetation removes CO 2 from the atmosphere; an important climate regulation service that slows global warming. This 119 Pg C per annum transfer of CO 2 into plants—gross primary productivity (GPP)—is the largest land carbon flux globally. While understanding past and anticipated future GPP changes is necessary to support carbon management, the factors driving long-term changes in GPP are largely unknown. In this study, we show that 1901 to 2010 changes in GPP have been dominated by anthropogenic activity. Our dual constraint attribution approach provides three insights into the spatiotemporal patterns of GPP change. First, anthropogenic controls on GPP change have increased from 57% (1901 decade) to 94% (2001 decade) of the vegetated land surface. Second, CO 2 fertilization and nitrogen deposition are the most important drivers of change, 19.8 and 11.1 Pg C per annum (2001 decade) respectively, especially in the tropics and industrialized areas since the 1970’s. Third, changes in climate have functioned as fertilization to enhance GPP (1.4 Pg C per annum in the 2001 decade). These findings suggest that, from a land carbon balance perspective, the Anthropocene began over 100 years ago and that global change drivers have allowed GPP uptake to keep pace with anthropogenic emissions.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Solvothermal synthesis of MOF-derived supported Ru nanocatalysts for low-temperature ammonia synthesis

We report the synthesis and scale-up of Ru catalysts that use high porosity MOF templates grown on graphitic carbon supports via solvothermal synthesis. Thermal treatment of the MOF resulted in well-dispersed Ru nanoparticles that are fully stabilized by in-situ graphitization of the surrounding carbon. The resulting catalyst has demonstrated significant improvement in activity for low-temperature NH 3 synthesis, and catalyst production has been scaled up from 1 g per batch to 200 g per batch scales.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Stabilizing alkaline fuel cells with a niobium-doped brookite titanium dioxide catalyst support

Anion-exchange membrane fuel cells represent a promising and scalable approach for hydrogen energy utilization. However, their development is hindered by the weak bonding between metal catalysts and carbon supports, along with challenges in fabricating electronically/ionically conductive electrodes. Here, we report a composite cathode of Nb-doped brookite TiO 2 nanorods that have robust stability when combined with Pt nanoscale catalysts in an alkaline fuel cell. The composite cathode, fabricated without the addition of an ionomer, delivers a power density of 419 mW cm −2 at a current density of 650 mA cm −2 and a voltage retention of 81% at 100 mA cm −2 after 25 h, substantially outperforming a cathode fabricated from commercial Pt/C. Further investigations of the chemical structure, anion exchange capacity, and mass transfer resistance reveal that a solvent residue derived from N-methylpyrrolidone plays an important role in charge transfer and mass transport in the alkaline fuel cell.

alkaline fuel cell↗
DOE OSTI2024

Predicting Adhesion Energies of Metal Nanoparticles to Support Surfaces, Which Determines Metal Chemical Potential versus Particle Size and Thus Catalyst Performance

Improved catalysts and electrocatalysts composed of transition metal nanoparticles dispersed on high-area supports are essential for energy and environmental technologies. The chemical potential of the metal atoms in these supported nanoparticles is an important descriptor that correlates with both their catalytic activity and deactivation rate. This descriptor (μ M ) is predictably determined by the particle size and the adhesion energy per unit area at the metal/support interface (E adh ). We show here that the adhesion energies for different metals on a given support scale linearly with a simple property of the metal: for oxides, it is proportional to the metal oxophilicity, and for the carbon support, it increases linearly with metal carbophilicity (both divided by the area per metal atom). Furthermore, these relationships allow predicting E adh for other metal/support combinations, thus allowing estimation of μ M versus particle size and thereby better structure-based predictions of catalysts’ performance, which can aid in designing improved catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Atomically dispersed single iron sites for promoting Pt and Pt 3 Co fuel cell catalysts: performance and durability improvements

Significantly reducing platinum group metal (PGM) loading while improving catalytic performance and durability is critical to accelerating proton-exchange membrane fuel cells (PEMFCs) for transportation. In this study, we report an effective strategy to boost PGM catalysts through integrating PGM-free atomically-dispersed single metal active sites in the carbon support toward the cathode oxygen reduction reaction (ORR). We achieved uniform and fine Pt nanoparticle (NP) (~2 nm) dispersion on an already highly ORR-active FeN 4 site-rich carbon (FeN 4 –C). Furthermore, we developed an effective approach to preparing a well-dispersed and highly ordered L1 2 Pt 3 Co intermetallic nanoparticle catalyst on the FeN 4 –C support. DFT calculations predicted a synergistic interaction between Pt clusters and surrounding FeN 4 sites through weakening O 2 adsorption by 0.15 eV on Pt sites and reducing activation energy to break O–O bonds, thereby enhancing the intrinsic activity of Pt. Experimentally, we verified the synergistic effect between Pt or Pt 3 Co NPs and FeN 4 sites, leading to significantly enhanced ORR activity and stability. Especially in a membrane electrode assembly (MEA) with a low cathode Pt loading (0.1 mg Pt cm –2 ), the Pt/FeN 4 –C catalyst achieved a mass activity of 0.451 A mg Pt –1 and retained 80% of the initial values after 30 000 voltage cycles (0.60 to 0.95 V), exceeding DOE 2020 targets. Furthermore, the Pt 3 Co/FeN 4 catalyst achieved significantly enhanced performance and durability concerning initial mass activity (0.72 A mg Pt –1 ), power density (824 mW cm –2 at 0.67 V), and stability (23 mV loss at 1.0 A cm –2 ). The approach to exploring the synergy between PGM and PGM-free Fe–N–C catalysts provides a new direction to design advanced catalysts for hydrogen fuel cells and various electrocatalysis processes.

25 ENERGY STORAGE↗
DOE OSTI2024

Tuning Strong Metal–Support Interactions via Synergistic Alloying

The encapsulation phenomenon associated with strong metal-support interaction (SMSI) has been largely restricted to catalyst systems consisting of group VIII metals with high surface energy and reducible transition metal oxide supports with low surface energy. Here, we demonstrate an encapsulation phenomenon that, while sharing morphological similarities with conventional SMSI, follows a distinctive pathway. This is shown by the encapsulation of CuAu nanoparticles (NPs) supported on highly ordered pyrolytic graphite (HOPG). Through dynamic monitoring of Cu, Au, and Cu 50 Au 50 NPs in an oxidizing atmosphere using ambient-pressure X-ray photoelectron spectroscopy, we show that this spontaneous encapsulation is achieved through the synergistic effect of the alloying elements. Specifically, the surface segregation of Cu promotes dissociative O 2 adsorption, leading to the formation of atomic O species, while the subsurface enrichment of Au hinders O incorporation into the bulk of CuAu NPs. Consequently, O spillover onto the graphite support occurs, resulting in the oxidation of the HOPG surface into graphitic oxide species. The higher affinity of the graphitic oxide species toward the Cu-segregated surface prompts their migration from the HOPG support to encapsulate the CuAu NPs. Finally, these results transcend the conventional SMSI and bear practical implications for the design and development of heterogeneous catalysts, particularly in carbon-supported alloy systems.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Nanocolumnar Pt:Ni Alloy Thin Films by High Pressure Sputtering for Oxygen Reduction Reaction

Self-supported nanocolumnar Pt:Ni thin films (TFs) with varying Pt:Ni atomic ratios and Pt mass loadings were produced on a microporous layer (MPL)-like surface composed of carbon particles by high pressure sputtering and examined as oxygen reduction reaction (ORR) electrocatalysts for polymer electrolyte membrane fuel cells. Cauliflower-like microstructures were observed from scanning electron microscopy imaging. Various Pt:Ni atomic ratios were obtained by simply changing the relative deposition power between Pt and Ni source and investigated by X-ray diffraction and quartz crystal microbalance analysis. Additionally, electrochemical characterization of the Pt:Ni-TF/MPL-like-layer/glassy-carbon samples was conducted through benchtop cyclic voltammetry and rotating disk electrode measurements. The electrochemically active surface area (ECSA) was found to be between 22–42 m 2 g -1 for different Pt:Ni atomic ratios. Lower Pt mass loadings exhibited a higher ECSA and the catalytic activity of all Pt:Ni ratios increased with the increase in Pt mass loading. The ORR activity of the Pt:Ni-TFs increased in the order of 3:1 < 1:1 < 1:3 with exhibiting a specific activity of 1781 μA cm -2 and mass activity of 0.66 A mg -1 for the Ni-rich film with 1:3 ratio. The catalytic performance of Pt:Ni-TFs were higher than traditional high surface area carbon supported Pt nanoparticles, elemental Pt nanorods, and Pt-Ni nanorods.

08 HYDROGEN↗
DOE OSTI2022

Coupled continuum and network model framework to study catalyst layers of polymer electrolyte fuel cells

The nanostructured thin film (NSTF) catalyst layers which have demonstrated high power densities, mass activities, and exceptional metal and support stability can have limited operational robustness due to their thin thickness and the hydrophilicity of the metal-coated nano whiskers. The dispersed nanostructured thin film (dNSTF) catalyst layers have been developed by dispersing the NSTF Pt whiskers with ionomer and carbon support to increase the thickness and hydrophobicity. Continuum and network models (NM) are coupled through boundary conditions to study the polymer electrolyte fuel cell with a dNSTF cathode catalyst layer. The coupled model combines the computational efficiency of the continuum model with the pore-scale information in the dNSTF cathode catalyst layer of the NM. It captures the special morphology of the partially ionomer/water covered cylindrical whiskers, as well as water percolation through the pore structures and their impact on the cell performance. Here we observe optimal ionomer coverage on whiskers to be 0.5, ionomer to carbon ratio to be 0.9 and higher whisker to carbon ratios to be desired.

08 HYDROGEN↗
DOE OSTI2023

Hierarchically Porous Carbons with Highly Curved Surfaces for Hosting Single Metal FeN 4 Sites as Outstanding Oxygen Reduction Catalysts

Iron–nitrogen–carbon (Fe₋N₋C) materials have emerged as a promising alternative to platinum-group metals for catalyzing the oxygen reduction reaction (ORR) in proton-exchange-membrane fuel cells. However, their low intrinsic activity and stability are major impediments. Herein, an Fe₋N–C electrocatalyst with dense FeN 4 sites on hierarchically porous carbons with highly curved surfaces (denoted as FeN 4 - hc C) is reported. The FeN 4 - hc C catalyst displays exceptional ORR activity in acidic media, with a high half-wave potential of 0.85 V (versus reversible hydrogen electrode) in 0.5 m H 2 SO 4 . When integrated into a membrane electrode assembly, the corresponding cathode displays a high maximum peak power density of 0.592 W cm -2 and demonstrates operating durability over 30 000 cycles under harsh H 2 /air conditions, outperforming previously reported Fe–N₋C electrocatalysts. These experimental and theoretical studies suggest that the curved carbon support fine-tunes the local coordination environment, lowers the energies of the Fe d-band centers, and inhibits the adsorption of oxygenated species, which can enhance the ORR activity and stability. This work provides new insight into the carbon nanostructure–activity correlation for ORR catalysis. It also offers a new approach to designing advanced single-metal-site catalysts for energy-conversion applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Tuning Active Site Flexibility by Defect Engineering of Graphene Ribbon Edge‐hosted Fe−N 3 Sites

Abstract Nitrogen‐doped, carbon‐supported transition metal catalysts are excellent for several reactions. Structural engineering of M−N x sites to boost catalytic activity is rarely studied. Here, we demonstrate that the structural flexibility of Fe−N 3 site is vital for tuning the electronic structure of Fe atoms and regulating the catalytic transfer hydrogenation (CTH) activity. By introducing carbon defects, we construct Fe−N 3 sites with varying Fe−N bond lengths distinguishable by X‐ray absorption spectroscopy. We investigate the CTH activity by density‐functional theory and microkinetic calculations and reveal that the vertical displacement of the Fe atom out of the plane of the support, induced by the Fe−N 3 distortion, raises the Fe orbital and strengthens binding. We propose that the activity is controlled by the relaxation of the reconstructed site, which is further affected by Fe−N bond length, an excellent activity descriptor. We elucidate the origin of the CTH activity and principles for high‐performing Fe−N−C catalysts by defect engineering.

Yang, Piaoping↗
DOE OSTI2023

Silver-decorated palladium on carbon catalyst for enhanced ammonium formate dehydrogenation

Palladium (Pd)-based catalysts efficiently convert ammonium formate solution to hydrogen at low temperatures (<100 °C), but they tend to deactivate quickly during stability testing. This manuscript presents a systematic investigation into the catalytic properties of Pd–Ag bimetallic catalysts, focusing on their surface compositions and exploring the mechanisms behind the deactivation of Pd/Ag-based catalysts. Here this study reports a carbon-supported Pd–Ag bimetallic nanoparticle (NP) catalyst obtained through a galvanic replacement method, which showed enhanced formate dehydrogenation performance. The best catalyst, Pd 3 Ag 10 /ACA-G (Pd–Ag bimetallic NPs with a 3 : 10 mass ratio loaded on acid-washed activated carbon, prepared by the galvanic replacement method), presents the highest activity with a TOF of 5202 h -1 (~2.6-fold of commercial Pd/C). The enhanced electron density of Pd–Ag bimetallic nanoparticles, coupled with the advantages of a smaller nanoparticle size, and the modulation of hydrogen adsorption energy through the Ag/Pd surface alloy on the Ag/Pd(111) facet, collectively resulted in experimentally higher turnover rates of hydrogen production. The changes on the catalyst surface, including surface Ag fraction decrease, NP size growth, and O-containing species (carboxylate, etc.) adsorption, gradually resulted in catalyst deactivation.

08 HYDROGEN↗
DOE OSTI2023

Tuning Active Site Flexibility by Defect Engineering of Graphene Ribbon Edge–hosted Fe–N3 Sites

Nitrogen-doped, carbon-supported transition metal catalysts are excellent for several reactions. Structural engineering of metal-Nx sites to boost catalytic activity is rarely studied. Here, we demonstrate that the structural flexibility of Fe-N3 site is vital for tuning the electronic structure of Fe atoms and regulating the catalytic transfer hydrogenation (CTH) activity. By introducing carbon defects, we construct Fe-N3 sites with varying Fe-N bond lengths distinguishable by X-ray absorption spectroscopy. We investigate the CTH activity by density functional theory and microkinetic calculations and reveal that the vertical displacement of the Fe atom out of the plane of the support, induced by the Fe-N3 distortion, raises the Fe [[EQUATION]]orbital and strengthens binding. We propose that the activity is controlled by the relaxation of the reconstructed site, which is further affected by Fe-N bond length, an excellent activity descriptor. Furthermore, we elucidate the origin of the CTH activity and principles for high-performing Fe-N-C catalysts by defect engineering.

09 BIOMASS FUELS↗
DOE OSTI2024

Unveiling the porosity effect of superbase ionic liquid-modified carbon sorbents in CO 2 capture from air

Direct air capture (DAC) of CO 2 represents one of the most promising technologies to achieve negative carbon emissions. In this work, the superbase ionic liquids (ILs)-modified carbon substrates were developed for DAC of CO 2 by harnessing the strong CO 2 binding capability of IL and the ordered porous channels of the carbon supports. Detailed porosity analysis revealed that the IL with an aromatic cation and an oxygenate anion preferred to fill the micropores, and a thin layer was created on the surface of the mesopores. Strong π-π interaction between the IL layer and the carbon surface was disclosed by wide-angle X-ray scattering (WAXS) analysis, leading to enhanced thermal stability of the IL phase. For the same lL coating amount, the DAC of CO 2 evaluation revealed that a larger mesopore size and pore volume in the carbon/IL composite materials led to higher CO 2 uptake capacity by exposing more active sites to integrate CO 2 from diluted sources. Further, the thermodynamic analysis confirmed the critical role of IL coating in providing strong chemisorption sites and significantly improved selectivity to enrich the diluted CO 2 from the air atmosphere. This work provides guidance on leveraging the scaffolds' surface properties and porosities of the scaffolds to optimize DAC of CO 2 behavior.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗