Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Active particles”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Ultrasmall amorphous zirconia nanoparticles catalyse polyolefin hydrogenolysis

Carbon–carbon bond cleavage reactions, adapted to deconstruct aliphatic hydrocarbon polymers and recover the intrinsic energy and carbon value in plastic waste, have typically been catalysed by metal nanoparticles or air-sensitive organometallics. Metal oxides that serve as supports for these catalysts are typically considered to be inert. Here we show that Earth-abundant, non-reducible zirconia catalyses the hydrogenolysis of polyolefins with activity rivalling that of precious metal nanoparticles. To harness this unusual reactivity, our catalytic architecture localizes ultrasmall amorphous zirconia nanoparticles between two fused platelets of mesoporous silica. Macromolecules translocate from bulk through radial mesopores to the highly active zirconia particles, where the chains undergo selective hydrogenolytic cleavage into a narrow, C18-centred distribution. Calculations indicated that C–H bond heterolysis across a Zr–O bond of a Zr(O) 2 adatom model for unsaturated surface sites gives a zirconium hydrocarbyl, which cleaves a C–C bond via β-alkyl elimination.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Voltage and temperature effects on low cobalt lithium-ion battery cathode degradation

Degradation of low cobalt lithium-ion cathodes was tested using a full factorial combination of upper cut-off voltage (4.0 V and 4.3 V vs. Li/Li + ) and operating temperature (25 °C and 60 °C). Half-cell batteries were analyzed with electrochemical and microstructural characterization methods. Electrochemical performance was assessed with galvanostatic cycling, cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS) supported by distribution of relaxation times (DRT) analysis. Electrode microstructure was characterized with scanning electron microscopy (SEM), X-ray diffraction (XRD), and X-ray absorption near edge structure (XANES) imaging. Higher cut-off voltage cycling shows presence of NiO x formation, a low diffusivity rock-salt phase, in both CV and XRD data. XRD patterns confirmed that the rock-salt phase was beginning to form at the low cut-off voltage at high temperature, but in much lower intensity than at the high cut-off voltage. Higher temperature accelerates degradation processes at both voltages. Degradation factors at high temperature include NiO x formation, cathode material dissolution, and electrolyte decomposition. SEM analysis suggests that supporting phases may isolate and disconnect active material particles reducing capacity retention and battery life cycle. DRT analysis and XANES imaging show that both high temperature samples revealed a NiO x phase based on an increased diffusive impedance and a visible shift in the XANES spectra. The low cut-off voltage, high temperature sample showed a split peak and shift to lower energies indicating early formation of the NiO x phase. The diffusive impedance, which hinders intercalation and deintercalation, is driven by the formation of the NiO x phase. While primarily driven by cut-off voltage, elevated temperature also contributes to this degradation mechanism.

electrochemical impedance spectroscopy↗
DOE OSTI2026

Engineering Microstructure in Dry-Processed Cathodes Via Calendering

Calendering serves as a multifunctional step in dry electrode processing that not only densifies the electrode but also induces polytetrafluoroethylene (PTFE) fibrillation and reorganizes the microstructure. These coupled effects are essential for achieving electrical connectivity and sufficient cohesion, yet they also introduce trade-offs, such as active material particle fracture, pore collapse, and excessive porosity loss, that can hinder ionic transport. This research systematically maps the calendering parameter space for LiNi0.6Mn0.2Co0.2O2 (NMC622) dry cathodes with a target thickness of ∼100 µm and porosity of ∼30% by varying roll gaps, roll temperature, roll speed, and the number of passes. A practical processing window for this formulation and electrode architecture is identified that achieves sufficient PTFE fibrillation and strong interfacial contact while minimizing particle fracture and preserving the porosity required for efficient ionic transport. In particular, gradual-gap calendering with moderate per-pass compression mitigates fracture and pore collapse while still reaching the target thickness with reasonable throughput, and slower roll speeds with modest roll temperatures further reduce mechanical damage. These results provide actionable guidance for scaling NMC622-based thick dry-processed cathodes.

Park, Hyunji↗
DOE OSTI2020

Enhancing nanostructured nickel-rich lithium-ion battery cathodes via surface stabilization

Layered, nickel-rich lithium transition metal oxides have emerged as leading candidates for lithium-ion battery (LIB) cathode materials. High-performance applications for nickel-rich cathodes, such as electric vehicles and grid-level energy storage, demand electrodes that deliver high power without compromising cell lifetimes or impedance. Nanoparticle-based nickel-rich cathodes seemingly present a solution to this challenge due to shorter lithium-ion diffusion lengths compared to incumbent micrometer-scale active material particles. However, since smaller particle sizes imply that surface effects become increasingly important, particle surface chemistry must be well characterized and controlled to achieve robust electrochemical properties. Moreover, residual surface impurities can disrupt commonly used carbon coating schemes, which result in compromised cell performance. Using x-ray photoelectron spectroscopy, here we present a detailed characterization of the surface chemistry of LiNi0.8Al0.15Co0.05O2 (NCA) nanoparticles, ultimately identifying surface impurities that limit LIB performance. With this chemical insight, annealing procedures are developed that minimize these surface impurities, thus improving electrochemical properties and enabling conformal graphene coatings that reduce cell impedance, maximize electrode packing density, and enhance cell lifetime fourfold. Overall, this work demonstrates that controlling and stabilizing surface chemistry enables the full potential of nanostructured nickel-rich cathodes to be realized in high-performance LIB technology.

Lim, Jin-Myoung↗
DOE OSTI2020

In Operando XANES Imaging of High Capacity Intermetallic Anodes for Lithium Ion Batteries

In operando 2D X-ray absorption near edge structure (XANES) imaging was performed near the Cu K-edge during cycling of Cu 6 Sn 5 composite anodes for lithium ion batteries. Galvanostatic lithiation and delithiation with intermittent constant voltage holds near reaction plateaus show evolution of absorption spectra for active material particles. XANES spectra obtained from images taken during cycling were compared to standard spectra for Cu, Cu 6 Sn 5 , and Li 2 CuSn. Chemical composition was assessed for Cu-containing phases. Distinct Cu, Cu 6 Sn 5 , and Li 2 CuSn regions were identified for each voltage plateau. Mechanical degradation, electrode particle fracture and expansion were observed during delithiation. Furthermore, movement of particles during cycling suggests that expansion also impacts the supporting secondary phases and the transport networks therein. These results demonstrate that spectroscopic X-ray imaging methods can clearly distinguish chemically distinct phases in alloy electrodes and have the versatility to observe the evolution of these phases during lithiation and delithiation.

25 ENERGY STORAGE↗
DOE OSTI2020

Rate-Dependent Aging Resulting from Fast Charging of Li-Ion Cells

The mass electrification of personal and service vehicles is reliant on the ability of battery packs to undergo extreme fast recharging. A central challenge is that the repeated exposure to high currents can trigger and/or accelerate mechanisms of performance degradation, such as lithium deposition, mechanical damage of active material particles, and impedance rise. Here, we investigate whether constraining high-rate charging to limited state-of-charge (SOC) ranges can mitigate these aging processes. Our experiments map the boundaries of lithium plating conditions, and also indicate that permanent losses of electrode capacity appear to be a function of cycle number, but not charging rate. Interestingly, we show that impedance rise appears to depend on charging rate alone, and not on the amount of charge passed at each cycle. This observation suggests that limiting fast charging to a narrow SOC range would only delay cell aging, but not fully prevent it from happening. We identify oxide-particle cracking as the likely mechanism for this impedance rise, suggesting that particle and electrode design are essential to enable fast charging. The findings of this work can inform the development of fast-charging protocols that are less damaging to cell health.

25 ENERGY STORAGE↗
DOE OSTI2022

Methods—Kintsugi Imaging of Battery Electrodes: Distinguishing Pores from the Carbon Binder Domain using Pt Deposition

The mesostructure of porous electrodes used in lithium-ion batteries strongly influences cell performance. Accurate imaging of the distribution of phases in these electrodes would allow this relationship to be better understood through simulation. However, imaging the nanoscale features in these components is challenging. While scanning electron microscopy is able to achieve the required resolution, it has well established difficulties imaging porous media. This is because the flat imaging planes prepared using focused ion beam milling will intersect with the pores, which makes the images hard to interpret as the inside walls of the pores are observed. It is common to infiltrate porous media with resin prior to imaging to help resolve this issue, but both the nanoscale porosity and the chemical similarity of the resins to the battery materials undermine the utility of this approach for most electrodes. In this study, a technique is demonstrated which uses in situ infiltration of platinum to fill the pores and thus enhance their contrast during imaging. Reminiscent of the Japanese art of repairing cracked ceramics with precious metals, this technique is referred to as the kintsugi method. The images resulting from applying this technique to a conventional porous cathode are presented and then segmented using a multi-channel convolutional method. We show that while some cracks in active material particles were empty, others appear to be filled (perhaps with the carbon binder phase), which will have implications for the rate performance of the cell. Energy dispersive X-ray spectroscopy was used to validate the distribution of phases resulting from image analysis, which also suggested a graded distribution of the binder relative to the carbon additive. The equipment required to use the kintsugi method is commonly available in major research facilities and so we hope that this method will be rapidly adopted to improve the imaging of electrode materials and porous media in general.

25 ENERGY STORAGE↗
DOE OSTI2023

The Effects of Lithium Ions and pH on the Function of Polyacrylic Acid Binder for Silicon Anodes

Binder plays a critical role in the performance of silicon anodes for lithium-ion batteries, specifically by connecting particles of active material and promoting adhesion to the current collector. Recent studies have differed on the relative cycle life of silicon anodes made from water-based polyacrylic acid (PAA) vs LiOH-PAA binders. Differences between the two may be due to the pH value or the extra Li + in the binder, both of which change when LiOH is added to PAA. Here we investigate the impact of these two variables on the performance of silicon anodes. Regarding the effect of Li + , cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) results confirm our hypothesis that the extra Li + facilitates ion transport. Regarding pH, we find that high pH in binders is detrimental to the electrode mechanical integrity, as observed in peeling tests and cross-sectional imaging. However, viscosity tests reveal that increased pH benefits the coating and mixing process. Further, our cycling results show that LiOH-PAA binder maintains greater cell capacity than does PAA, and further that LiOH-PAA at pH 4.5 leads to a cell with the highest capacity. Therefore, an intermediate pH is an optimal compromise between benefits observed for the low and high pH experiments.

25 ENERGY STORAGE↗
DOE OSTI2025

Electrochemical-Mechanical Coupling Strongly Affects the Performance of Nanopore, Thin-Film, and Solid-State Batteries

Here, the present study focuses on the electrochemical-mechanical (ECM) coupling effects of a thin-film, solid-state battery with only stiff, ceramic materials, in contrast to prior investigations that focus on individual active material particles or aggregations of particles. We model the impacts of ECM couplings including stress-transport and stress-equilibrium potential on the full-cell performance and potential mechanical failure modes of a thin-film battery conformally deposited in a nanopore scaffold, which is an experimentally achievable device. Model results indicate electrode volume changes due to lithium insertion or removal, along with mechanical boundary conditions, result in stress gradients that alter the lithium-ion flux, reduce lithium concentration gradients, and improve cell rate capability. However, the high stress levels in the cell can also lead to mechanics-related failure such as the separation of cell layers. For the parameter set in this work, stress-transport coupling has a much greater influence on rate capability than stress-potential coupling. Optimization of thin-film batteries to harness the benefits of ECM coupling effects requires leveraging geometric design and material selection. The current work underscores the need for further theoretical and experimental investigation into ECM coupling effects in thin-film batteries to enhance their understanding and design optimization.

25 ENERGY STORAGE↗
DOE OSTI2025

Deployable Element Ultra-High Vacuum Pump

Advancing Ultra High Vacuum (UHV) Pumping Technology: The deployable UHV pump team has designed a theoretical model to boost efficiency in high vacuum environments. Traditional systems face challenges with random molecular motion. The innovative windmill design, using titanium sublimation technology, reduces randomness by deploying a gettering surface that actively captures particles. This marks a notable advancement in UHV pumping technology.

43 PARTICLE ACCELERATORS↗
DOE OSTI2021

Techno-Economic Analysis of a Concentrating Solar Power Plant Using Redox-Active Metal Oxides as Heat Transfer Fluid and Storage Media

We present results for a one-dimensional quasi-steady-state thermodynamic model developed for a 111.7 MW e concentrating solar power (CSP) system using a redox-active metal oxide as the heat storage media and heat transfer agent integrated with a combined cycle air Brayton power block. In the energy charging and discharging processes, the metal oxide CaAl 0.2 Mn 0.8 O 2.9-δ (CAM28) undergoes a reversible, high temperature redox cycle including an endothermic oxygen-releasing reaction and exothermic oxygen-incorporation reaction. Concentrated solar radiation heats the redox-active oxide particles under partial vacuum to drive the reduction extent deeper for increased energy density at a fixed temperature, thereby increasing storage capacity while limiting the required on sun temperature. Direct counter-current contact of the reduced particles with compressed air from the Brayton compressor releases stored chemical and sensible energy, heating the air to 1,200°C at the turbine inlet while cooling and reoxidizing the particles. The cool oxidized particles recirculate through the solar receiver subsystem for another cycle of heating and reduction (oxygen release). We applied the techno-economic model to 1) size components, 2) examine intraday operation with varying solar insolation, 3) estimate annual performance characteristics over a simulated year, 4) estimate the levelized cost of electricity (LCOE), and 5) perform sensitivity analyses to evaluate factors that affect performance and cost. Simulations use hourly solar radiation data from Barstow, California to assess the performance of a 111.7 MW e system with solar multiples (SMs) varying from 1.2 to 2.4 and storage capacities of 6–14 h. The baseline system with 6 h storage and SM of 1.8 has a capacity factor of 54.2%, an increase from 32.3% capacity factor with no storage, and an average annual energy efficiency of 20.6%. Calculations show a system with an output of 710 GWh e net electricity per year, 12 h storage, and SM of 2.4 to have an installed cost of $329 million, and an LCOE of 5.98 ¢/kWh e . This value meets the U.S. Department of Energy’s SunShot 2020 target of 6.0 ¢/kWh e ( U. S Department of Energy, 2012 ), but falls just shy of the 5.0 ¢/kWh e 2030 CSP target for dispatchable electricity ( U. S Department of Energy, 2017 ). The cost and performance results are minimally sensitive to most design parameters. However, a one-point change in the weighted annual cost of capital from 8 to 7% (better understood as a 12.5% change) translates directly to an 11% decrease (0.66 ¢/kWhe) in the LCOE.

Gorman, Brandon T.↗
DOE OSTI2021

Cloud drop number concentrations over the western North Atlantic Ocean: seasonal cycle, aerosol interrelationships, and other influential factors

Cloud drop number concentrations (N d ) over the western North Atlantic Ocean (WNAO) are generally highest during the winter (DJF) and lowest in summer (JJA), in contrast to aerosol proxy variables (aerosoloptical depth, aerosol index, surface aerosol mass concentrations, surface cloud condensation nuclei (CCN) concentrations) that generally peak inspring (MAM) and JJA with minima in DJF. Using aircraft, satellite remote sensing, ground-based in situ measurement data, and reanalysis data, we characterize factors explaining the divergent seasonal cycles and furthermore probe into factors influencing N d on seasonal timescales. The results can be summarized well by features most pronounced in DJF, including features associated with cold-air outbreak (CAO) conditions such as enhanced values of CAO index, planetary boundary layer height (PBLH),low-level liquid cloud fraction, and cloud-top height, in addition to winds aligned with continental outflow. Data sorted into high- and low-N d days in each season, especially in DJF, revealed that all of these conditions were enhanced on the high-N d days, including reduced sea level pressure and stronger wind speeds. Although aerosols may be more abundant in MAM and JJA, the conditions needed to activate those particles into cloud droplets are weaker than in colder months, which is demonstrated by calculations of the strongest (weakest) aerosol indirect effects in DJF (JJA) based on comparing N d to perturbations in four different aerosol proxy variables (total and sulfate aerosol optical depth, aerosol index, surface mass concentration of sulfate). We used three machine learning models and up to 14 input variables to infer about most influential factors related to N d for DJF and JJA, with the best performance obtained with gradient-boosted regression tree (GBRT) analysis. The model results indicated that cloud fraction was the most important input variable, followed by some combination (depending on season) of CAO index and surface mass concentrations of sulfate and organic carbon. Future work is recommended to further understand aspects uncovered here such as impacts of free tropospheric aerosol entrainment on clouds, degree of boundary layer coupling, wet scavenging, and giant CCN effects on aerosol–N d relationships, updraft velocity, and vertical structure of cloud properties such as adiabaticity that impact the satellite estimation of N d .

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Desulfurization and sulfur tolerant hydrogenation processes of hydrocarbon feedstocks

The present invention relates to the use of adsorbents comprising zinc oxide nanowires decorated with catalytically active metal particles for the removal of sulfur from hydrocarbon feedstocks, including the desulfurization of diesel fuels and the deep desulfurization of natural gas, and to the use of decorated zinc oxide nanowire adsorbents for the hydrogenation of naphthalene selectively to tetralin in the presence of sulfur compounds. The adsorbent comprises nickel metal particles or nickel-zinc alloy particles deposited on zinc oxide nanowires.

Sunkara, Mahendra↗
DOE OSTI2022

Scaffolding matrix with internal nanoparticles

A battery electrode composition is provided comprising composite particles, with each composite particle comprising active material and a scaffolding matrix. The active material is provided to store and release ions during battery operation. For certain active materials of interest, the storing and releasing of the ions causes a substantial change in volume of the active material. The scaffolding matrix is provided as a porous, electrically-conductive scaffolding matrix within which the active material is disposed. In this way, the scaffolding matrix structurally supports the active material, electrically interconnects the active material, and accommodates the changes in volume of the active material.

Yushin, Gleb↗
DOE OSTI2022

Scaffolding matrix with internal nanoparticles

A battery electrode composition is provided comprising composite particles, with each composite particle comprising active material and a scaffolding matrix. The active material is provided to store and release ions during battery operation. For certain active materials of interest, the storing and releasing of the ions causes a substantial change in volume of the active material. The scaffolding matrix is provided as a porous, electrically-conductive scaffolding matrix within which the active material is disposed. In this way, the scaffolding matrix structurally supports the active material, electrically interconnects the active material, and accommodates the changes in volume of the active material.

25 ENERGY STORAGE↗
DOE OSTI2024

Scaffolding matrix with internal nanoparticles

A battery electrode composition is provided comprising composite particles, with each composite particle comprising active material and a scaffolding matrix. The active material is provided to store and release ions during battery operation. For certain active materials of interest, the storing and releasing of the ions causes a substantial change in volume of the active material. The scaffolding matrix is provided as a porous, electrically-conductive scaffolding matrix within which the active material is disposed. In this way, the scaffolding matrix structurally supports the active material, electrically interconnects the active material, and accommodates the changes in volume of the active material.

Yushin, Gleb↗
DOE OSTI2023

Regulating the properties of activated carbon for supercapacitors: impact of particle size and degree of aromatization of hydrochar

Hydrochar (HC), obtained by the hydrothermal carbonization (HTC) of biomass, is an excellent precursor for preparing activated carbon (AC). However, the effects of the intrinsic properties of HC on the microstructure and electrochemical properties of AC are largely unknown. Here, this study investigates the impact of particle size and the degree of aromatization of in-situ HC on the microstructure and electrochemical properties of AC. Our results show that a large particle size and a high degree of aromatization help protect the HC from overactivation by ZnCl 2 , resulting in an large specific surface area (SSA > 2000 m 2 /g) and high mesopore to micropore volume ratio value ( V mes /V mic > 0.3) of the AC. Electrochemical performance measurements show a maximum specific capacitance of 218 F/g at 0.5 A/g was achieved in all samples where the AC (AC180-10 h) was prepared by activating HC180-10 h with a large size, a high degree of aromatization, and abundant surface oxygen-containing functional groups. After AC180-10 h was assembled into a supercapacitor, the specific capacitance of AC180-10 h still reached 158 F/g at 0.5 A/g, and it showed excellent cycling stability. This study advances the understanding of the impact of HC particle size and degree of aromatization on AC properties, providing new insights into tailoring HC qualities so that improving improve the properties of AC.

36 MATERIALS SCIENCE↗