Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ASH CONTENT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

Fast Pyrolysis Oil Stabilization: An Integrated Catalytic and Membrane Approach for Improved Bio-oils. Final Report

This University of Massachusetts, Amherst project, "Fast Pyrolysis Oil Stabilization: An Integrated Catalytic and Membrane Approach for Improved Bio-oils" started on 1st February 2009 and finished on August 31st 2011. The project consisted following tasks: Task 1.0: Char Removal by Membrane Separation Technology The presence of char particles in the bio-oil causes problems in storage and end-use. Currently there is no well-established technology to remove char particles less than 10 micron in size. This study focused on the application of a liquid-phase microfiltration process to remove char particles from bio-oil down to slightly sub-micron levels. Tubular ceramic membranes of nominal pore sizes 0.5 and 0.8m were employed to carry out the microfiltration, which was conducted in the cross-flow mode at temperatures ranging from 38 to 45 C and at three different trans-membrane pressures varying from 1 to 3 bars. The results demonstrated the removal of the major quantity of char particles with a significant reduction in overall ash content of the bio-oil. The results clearly showed that the cake formation mechanism of fouling is predominant in this process. Task 2.0 Acid Removal by Membrane Separation Technology The feasibility of removing small organic acids from the aqueous fraction of fast pyrolysis bio-oils using nanofiltration (NF) and reverse osmosis (RO) membranes was studied. Experiments were carried out with a single solute solutions of acetic acid and glucose, binary solute solutions containing both acetic acid and glucose, and a model aqueous fraction of bio-oil (AFBO). Retention factors above 90% for glucose and below 0% for acetic acid were observed at feed pressures near 40 bar for single and binary solutions, so that their separation in the model AFBO was expected to be feasible. However, all of the membranes were irreversibly damaged when experiments were conducted with the model AFBO due to the presence of guaiacol in the feed solution. Experiments with model AFBO excluding guaiacol were also conducted. NF membranes showed retention factors of glucose greater than 80% and of acetic acid less than 15% when operated at transmembrane pressures near 60 bar. Task 3.0 Acid Removal by Catalytic Processing It was found that the TAN reduction in bio-oil was very difficult using low temperature hydrogenation in flow and batch reactors. Acetic acid is very resilient to hydrogenation and we could only achieve about 16% conversion for acetic acid. Although it was observed that acetic acid was not responsible for instability of aqueous fraction of bio-oil during ageing studies (described in task 5). The bimetallic catalyst PtRe/ceria-zirconia was found to be best catalyst because its ability to convert the acid functionality with low conversion to gas phase carbon. Hydrogenation of the whole bio-oil was carried out at 125°C, 1450 psi over Ru/C catalyst in a flow reactor. Again, negligible acetic acid conversion was obtained in low temperature hydrogenation. Hydrogenation experiments with whole bio-oil were difficult to perform because of difficulty to pumping the high viscosity oil and reactor clogging. Task 4.0 Acid Removal using Ion Exchange Resins DOWEX M43 resin was used to carry out the neutralization of bio-oil using a packed bed column. The pH of the bio-oil increased from 2.43 to 3.7. The GC analysis of the samples showed that acetic acid was removed from the bio-oil during the neutralization and recovered in the methanol washing. But it was concluded that process would not be economical at large scale as it is extremely difficult to regenerate the resin once the bio-oil is passed over it. Task 5.0 Characterization of Upgraded Bio-oils We investigated the viscosity, microstructure, and chemical composition of bio-oils prepared by a fast pyrolysis approach, upon aging these fuels at 90ºC for periods of several days. Our results suggest that the viscosity increase is not correlated with the acids or char present in the bio-oils. The viscosity increase is due to formation of high molecular weight polymeric species over time. Our work also suggests that hydrogenation of the samples is beneficial in eliminating the viscosity increase. Task 6.0 Commercialization Assessment Renewable Oil International LLC (ROI) was responsible for Task 6.0, Commercialization Assessment. As part of this effort ROI focused on methods to reduce char carryover in the vapor stream from the fast pyrolysis reactor and residence time of the vapor in the reactor. Changes were made in the bio-oil recovery methodology and a reactor sweep gas used to reduce vapor residence time. Cyclones were placed in the vapor stream to reduce char particulate carryover. Microfiltration of the bio-oil was also researched to remove char particulate from the bio-oil. The capital cost for these improvements would be less than 2% of the total plant capital cost.

09 BIOMASS FUELS↗

Characterization of Advanced Preprocessed Materials (Hydrothermal)

The initial hydrothermal treatment parameters did not achieve the proposed objective of this effort; the reduction of intrinsic ash in the corn stover. However, liquid fractions from the 170°C treatments was indicative that some of the elements routinely found in the ash that negatively impact the biochemical conversion processes had been removed. After reviewing other options for facilitating ash removal, sodium-citrate (chelating agent) was included in the hydrothermal treatment process, resulting in a 69% reduction in the physiological ash. These results indicated that chelation –hydrothermal treatment is one possible approach that can be utilized to reduce the overall ash content of feedstock materials and having a positive impact on conversion performance.

09 BIOMASS FUELS↗

Bio-energy Alliance High-Tonnage Bio-energy Crop Production and Conversion into Conventional Fuels

Maintaining a predictable and sustainable supply of feedstock for bioenergy conversion is a major goal to facilitate the efficient transition to cellulosic biofuels. Our work provides insight into the complex interactions among agronomic, edaphic, and climatic factors that affect the sustainability of bioenergy crop yields. Our results provide science-based agronomic response measures that document how to better manage bioenergy sorghum production from planting to harvest. We show that harvest aids provide no significant benefit as a means to decrease harvest moisture or improve bioenergy yields. Our efforts to identify optimal seeding rates under varied edaphic and climatological conditions reinforce previous findings that sorghum is a resilient plant that can efficiently adapt to changing population pressures by decreasing or increasing the numbers of additional shoots or tillers – where optimal seeding rates for high biomass photoperiod sensitive sorghum is 60,000 to 70,000 seeds per acre and 100,000 to 120,000 seeds per acre for sweet varieties. Our varietal adaptability trials revealed that high biomass photoperiod sensitive energy sorghum consistently outperforms conventional photoperiod insensitive sweet sorghum and high biomass forage sorghum as the preferred bioenergy sorghum type, with combined theoretical yields of both cellulosic and fermentable water-soluble sugars producing an average yield of 1,035 gallons of EtOH per acre. Our nitrogen trials reveal that sweet sorghums produce ample amounts of water-soluble sugars with minimal increases in nitrogen inputs, and that excess nitrogen can affect minor increases in biomass yields and cellulosic sugars but decrease bioenergy quality by decreasing water-soluble sugar concentrations and increasing ash content, specifically when plant tissue nitrogen concentrations exceed 0.6 %, dry weight basis. Finally, through our growth and re-growth trials, we show that single-cut high biomass sorghum bioenergy yields significantly exceed those of multiple-cut high biomass sorghum systems. Our agronomic yield and quality data will be uploaded to the Bioenergy KDF Website before the end of February 2013, with a date for public access to be determined pending peer-reviewed publication of our findings.

09 BIOMASS FUELS↗

AOI2 - Initial Engineering, Testing, and Design of a Commercial-Scale Postcombustion CO 2 Capture System on an Existing Coal-Fired Generating Unit (Project Carbon)

The continued long-term use of North Dakota lignite is likely dependent on creating a business case for carbon capture, utilization, and storage (CCUS) that also addresses society’s desire to reduce carbon emissions. CCUS coupled with enhanced oil recovery appears to be the most feasible option for utilities to sustain and grow the lignite industry. Establishing a market where lignite-powered utilities provide carbon dioxide (CO 2 ) to oil producers depends upon having a cost-effective method to capture CO 2 . The application of CO 2 capture technology to lignite-fired flue gas has challenges in addition to the cost of capture, including the effects of the buildup of heat-stable salts, aerosol formation, degradation of solvents or solid sorbents, or subsequent solvent loss. Lignite, especially North Dakota lignite, presents its own set of challenges that include the combination of high sodium, sulfur, and ash contents; NO x reduction; and footprint limitations. Project Carbon was designed to address these technical barriers and provide pre-FEED (preliminary front-end engineering and design) information necessary for additional commercial demonstrations to move forward. A long-term pilot-scale evaluation of Mitsubishi Heavy Industries’ (MHI’s) KS-1™ solvent at Minnkota Power Cooperative’s lignite-fired Milton R. Young Station Unit 2 (MRY2) was a major objective of the project. The purpose of the test was to demonstrate the technology’s compatibility with MRY2’s flue gas over an extended period of time. During the long-term test, aerosol sampling and measurement were performed, and a pilot-scale baghouse was tested to determine the effect of bag material and operation on aerosol concentrations in the flue gas. Project engineering and design work were performed to support the other major project objective: a pre-FEED study of CO 2 capture at MRY2. Finally, a techno-economic assessment (TEA) of the application of CO 2 capture to MRY2 was performed. This project was performed over a period of 28 months, with a total budget of $12,700,000. The U.S. Department of Energy’s (DOE’s) National Energy Technology Laboratory, through the Energy & Environmental Research Center’s (EERC’s) Cooperative Agreement, the North Dakota Industrial Commission, and industry partners ALLETE and Minnkota Power Cooperative, funded the project. The pilot-scale test system at MRY2 performed very well for the continuous test period of 83 days. The CO 2 capture plant achieved stable operation while utilizing MHI’s KS-1™ solvent and the MHI amine emission reduction unit. No major concerns were encountered when capturing CO 2 from lignite-fired flue gas. Challenges were encountered because the cooling water temperature was warmer than needed for the capture system to operate efficiently. This affected the ability of the solvent to capture CO 2 and promoted solvent loss through solvent entrainment caused by high CO 2 gas temperature within a cyclone separator. The KS-1™ solvent and the lignite-derived flue gas were analyzed during the long-term test. Analysis of the solvent indicates that, although some metals and heat-stable salts increased over the course of the long-term test, they were at levels that can be treated with filtration and reclaiming and do not pose a concern for effective solvent operation. Fourier transform infrared (FTIR) spectrometry was successfully used to determine the composition of the lignite-derived flue gas as well as concentrations of select components of the flue gas at various locations within the EERC’s CO 2 capture system. The formation of aerosols during the capture process is of interest, as are approaches for their reduction, especially in a baghouse. Testing of aerosol removal was performed using the EERC’s portable baghouse. It was found that both Ryton and polytetrafluoroethylene (PTFE) membrane bags were effective at reducing the level of aerosols during steady-state operation. During backpulse events, however, the amount of aerosols passing through the bags was an order of magnitude lower for the Ryton bags than the PTFE membrane bags. The testing showed that proper design of the baghouse air-to-cloth ratio as well as minimization of backpulsing can dramatically reduce the amount of aerosols that pass through the bags and remain in the flue gas stream exiting a baghouse system. A technology maturation plan (TMP) was performed to enable successful development of the Kansai Mitsubishi Carbon Dioxide Recovery® (KM CDR®) Process for application to a combustion flue gas for which the process has not yet been demonstrated. In the TMP, new challenges to the MHI CO 2 capture technology during its application to MRY2 were identified. These challenges included capture from lignite-fired (as opposed to subbituminous coal-fired) flue gas, a larger scope than previous applications of the technology, and implementation in a colder climate that could affect process and equipment operability. Because MRY2 is located where stack icing in the winter could be problematic, a rime icing study was performed. Rime icing modeling indicated that, under both 100% and 50% operating loads, there is a potential for many icing events during any given part of the year in which below-freezing weather conditions exist. The models showed that a critical amount of rime ice could be formed at the stack top during two or more events per year. CO 2 capture plant stack height and location will need to be determined in order to minimize the formation of rime ice. It was found that the integration of the MHI CO 2 capture process into the normal operation of the MRY2 steam turbine is a viable alternative to a cogeneration facility to provide steam and power for the carbon capture facility. The research performed under this project showed that CO 2 capture at a lignite-fired power plant can successfully be performed. No known fatal flaws that would prevent the continued development of the MRY2 CO 2 capture facility were identified during the pre-FEED study. A TEA performed following DOE methodology shows that applying capture technology to MRY2 may not only meet but exceed the DOE-recognized state-of-the-art baseline.

20 FOSSIL-FUELED POWER PLANTS↗

Elemental Analysis of Bio-Oils by Inductively Coupled Plasma Optical Emission Spectroscopy (ICP-OES). Laboratory Analytical Procedure (LAP), Issue Date: May 13, 2022

Concentrations of inorganic elements is a key quality metric for bio-oils as certain elements impact upgrading processes and product quality. Unless reduced or removed during production and processing, alkali and alkaline metals native to lignocellulosic biomass can carry over into bio-oils contributing to ash content and degraded catalyst performance during upgrading to hydrocarbon fuels or chemical products. Non-metallic elements such as sulfur and phosphorus can also negatively impact upgrading catalysts and product quality. Inductively coupled plasma optical emission spectroscopy (ICP-OES) can be used to measure inorganic elements of interest in bio-oils. This procedure covers the preparation and analysis of fast pyrolysis (FP) and catalytic fast pyrolysis (CFP) bio-oils. The concentrations of these elements can indicate potential bio-oil quality from the perspective of deoxygenation processes. The implications of elemental composition will depend on process parameters such as upgrading catalyst sensitivities. This Laboratory Analytical Procedure (LAP) covers two methods for quantification of inorganic elements by ICP-OES: Procedure A uses microwave assisted digestion with concentrated nitric acid, and Procedure B is an organic ICP-OES method utilizing a diglyme solvent.

09 BIOMASS FUELS↗

Using Chemical Reactor Models to Predict Fluidized Bed Pyrolysis Yields of Biomass Feedstocks

A detailed biomass pyrolysis kinetics scheme is implemented in reduced-order reactor models to predict chemical species yields from a fluidized bed reactor. The biomass composition in terms of cellulose, hemicellulose, lignins, and extractives are determined for several biomass feedstocks. Model results are compared to yields measured from a two-inch diameter bench-scale fluidized bed reactor operating at fast pyrolysis conditions. The reduced-order chemical reactor models compare favorably with the experimental measurements and capture trends in product yields due to biomass compositional effects such as high ash content. This work offers a computationally inexpensive approach to predict the quality of biomass pyrolysis products in a timely manner. Source code for the reactor models along with a biomass composition web tool are made available online for future scientific research efforts.

09 BIOMASS FUELS↗

ASSESSMENT OF HIGH-VOLUME HARVESTED FLY ASH BLENDS FOR USE IN PRECAST CONSTRUCTION

Declining supplies of fresh fly ashes in some regions have further driven the importance of using harvested fly ash as a supplementary cementitious material and thus replacement for more energy-intensive ordinary Portland cement (OPC). Higher replacement rates of OPC with fly ash in general has traditionally been limited in precast operations due to stringent early-age strength requirements necessitated by initial prestress and lifting/handling of hardened components – often well within 24 hours after fresh concrete placement. Therefore, a series of mix designs were developed, as part of a larger framework for reassessing high-volume fly ash (HVFA) use in the context of precast construction, to demonstrate the feasibility of using larger fractions of harvested fly ash in concrete formulations suitable for precast fabrication demands. More specifically, a target minimum 24-hour compressive strength of 24.1 MPa (3500 psi) was set, in accordance with conventional precast structural design checks, while increasing the fly ash content to 40% replacement of OPC – at least a 15% increase above the traditional limit of 25%. The effect of using more sustainable Type IL cement in contrast to conventional Type III Portland cement (the traditional standard for precast use) – both in conjunction with HVFA use – was also examined. Early-age mechanical properties including compressive strength, modulus of rupture, and modulus of elasticity were evaluated within the aforementioned early-age window. Lastly, corresponding design equations were then reassessed for their applicability with respect to the high-early strength HVFA mixes examined herein.

Gombeda, Matthew J.↗

Whole Algae Hydrothermal Liquefaction and Upgrading: A review of progress and challenges and insight into the future

This report summarizes the research at Pacific Northwest National Laboratory (PNNL) to evaluate the economic viability and environmental impact of using microalgae to produce fuels and other products via hydrothermal liquefaction (HTL). Over the past several years, PNNL has examined key aspects of feedstock cost and availability, formatting and conversion techniques, and the utilization of all HTL products. Investigations of feedstock cost led to opportunities to work with cost-advantaged algal feedstocks that can be provided at minimal cost for HTL processing. Cost-advantaged algae include wastewater-grown algae and harvested algal blooms. Although farm-cultivated algae offer the best possible biomass composition and scalability for HTL processing, the cost of the feedstock is too high to yield an economically competitive biofuel. Processing cost-advantaged feedstocks creates other unique challenges in adapting HTL to upgrade biomass with higher than typical ash content and less preferred composition (low lipid). Despite the challenges, HTL of cost-advantaged algae results in economically competitive pricing scenarios and significant advantages in reducing net emissions below 70% of the petroleum baseline. The utilization of a variety of potential non-fuel products from algal HTL, such as the use of HTL solids as a cement additive, provides a significant reduction in net emissions by offsetting emissions from other carbon-intense products. This report presents an analysis of the research conducted at PNNL to develop an economically and environmentally beneficial process for algae HTL.

09 BIOMASS FUELS↗

Carbon Ore-Derived Critical Materials for Clean Energy Technologies

Conference presentation at American Institute of Chemical Engineers (AIChE) Annual Meeting, San Diego, California, October 27–31, 2024. Trends in the manufacture of electric vehicles that use graphite-based LIBs are rising steeply in the United States and globally, but the U.S. domestic supply chains for graphite, the largest component in an LIB by mass, is severely limited and faces complicated geopolitical dynamics with foreign sources. Consequently, the United States has designated graphite as a critical mineral to focus attention and resources to develop technologies to meet the challenge of limited domestic graphite supply chains. Results obtained so far based on the UCOP process have successfully validated the technology at the laboratory scale, with the produced graphite material showing up to 95% degree of graphitization, high carbon purity of ~99.98%, residual ash content of ≤0.02%, negligible moisture, low trace elements, and high electrochemical stability. These results suggest that the emerging UCOP technology is a promising approach to effectively synthesize high-quality graphite from abundant coal and coal waste resources in the United States to create a sustainable domestic critical graphite supply chain. A brief description of the status of UCOP process development and representative results will be presented.

01 COAL, LIGNITE, AND PEAT↗

Using Incremental Changes to Convert Lignocellulosic Feedstocks to Cellulosic Ethanol

One billion tons of biomass feedstocks have been identified for the production of renewable biofuels and biochemicals. This is one of the key carbon feedstocks to supply energy to the transportation sector for light duty, heavy duty and aviation fuels. Utilization of lignocellulosic feedstocks supports an improved energy security by reducing demand of petroleum imports, agricultural development, job creation, and reducing greenhouse gas emissions. To date, however, operational challenges have stymied the industrial production of large volumes of lignocellulosic-based fuels and chemicals. As a result, significant research investment has been led by the United States Department of Energy to understand and improve operational reliability at pioneer cellulosic biorefineries. In this perspective article lignocellulosic conversion technologies are described that have been adopted from the starch ethanol process. The developed process culminated in successful demonstration of 1,000-h integrated runs using several feedstocks, including switchgrass, energy sorghum, and two types of corn kernel fiber. This report highlights process development that solved several of the issues that plagued—and continue to plague—many in the cellulosic sugars space such as biomass feeding into equipment, high ash content, diversified co-product value, and others.

09 BIOMASS FUELS↗

Studying the Suitability of Nineteen Lignins as Partial Polyol Replacement in Rigid Polyurethane/Polyisocyanurate Foam

In this study, nineteen unmodified lignins from various sources (hardwood, softwood, wheat straw, and corn stover) and isolation processes (kraft, soda, organosolv, sulfite, and enzymatic hydrolysis) were used to replace 30 wt.% of petroleum-based polyol in rigid polyurethane/polyisocyanurate (PUR/PIR) foam formulations. Lignin samples were characterized by measuring their ash content, hydroxyl content (Phosphorus Nuclear Magnetic Resonance Spectroscopy), impurities (Inductively Coupled Plasma), and pH. After foam formulation, properties of lignin-based foams were evaluated and compared with a control foam (with no lignin) via cell morphology, closed-cell content, compression strength, apparent density, thermal conductivity, and color analysis. Lignin-based foams passed all measured standard specifications required by ASTM International C1029-15 for type 1 rigid insulation foams, except for three foams. These three foams had poor compressive strengths, significantly larger cell sizes, darker color, lower closed-cell contents, and slower foaming times. The foam made with corn stover enzymatic hydrolysis lignin showed no significant difference from the control foam in terms of compressive strength and outperformed all other lignin-based foams due to its higher aliphatic and p-hydroxyphenyl hydroxyl contents. Lignin-based foams that passed all required performance testing were made with lignins having higher pH, potassium, sodium, calcium, magnesium, and aliphatic/p-hydroxyphenyl hydroxyl group contents than those that failed.

59 BASIC BIOLOGICAL SCIENCES↗

Determination of the effects of graphite material properties on ablation performance.

Application of statistical methods to the problem of identifying those material properties of artificial graphite having the strongest effect on ablation performance. Ablation performance, as determined by total length change during test, recession rate, surface temperature, surface texture, and degree of gouging, was measured on 40 different, commercially available, artificial graphites in a Mach 2 airstream having a nominal enthalpy of 2.2 MJ/kg and a stagnation pressure of 5.6 atm. Eighteen material properties were measured on these same graphites, and correlations between pairs of these material properties were developed where possible, reducing the original 18 properties to ten mutually independent properties. Multiple regression equations were formulated relating ablation performance to the reduced set of ten independent material properties, thereby identifying those material properties having the most pronounced effect on ablation performance. These regression equations reveal that for optimum ablation performance in the present environment, grain size should be small, ash content low, density and thermal conductivity high, and mean pore radius large.

Maahs, H. G.↗

Low-temperature refining of coal

Laboratory-tested process demonstrates technical feasibility of new low temperature chemical pretreatment of new coal that yields purified product with low sulfur, oxygen, and inorganic ash content.

Ganguli, P. S.↗

Continuous extrusion of coal

A feeding method for use with bituminous coals that exhibit plasticity at elevated temperatures is described and demonstrated on a small screw extruder previously used to extrude polyethylene. A metered feed of coal heated to a temperature just below that of incipient caking (approximately 450 C) is used. Modifications to the extruder consisting of ceramic band heaters, auxiliary cooling coils on the thrust bearing and special quick opening dies are detailed. Coals successfully extruded include high volatile A bituminous coals, high volatile B bituminous coals, a high volatile C bituminous coal and a coal with high ash content. The computer program, EXTRUD, used to simulate the extruder is described. Predicted power consumption exhibits 30% scatter, which is explained by the sensitivity of the coal friction coefficient to temperature profiles. Detailed analysis reveals some discrepancies in the program that need to be resolved.

England, C.↗

Improved Supercritical-Solvent Extraction of Coal

Raw coal upgraded by supercritical-solvent extraction system that uses two materials instead of one. System achieved extraction yields of 20 to 49 weight percent. Single-solvent yields are about 25 weight percent. Experimental results show extraction yields may be timedependent. Observed decreases in weight of coal agreed well with increases in ash content of residue.

Compton, L.↗

Aerosols from the Soufriere eruption plume of 17 April 1979

Aerosol samples collected from the April 17, 1979 eruption plume of Soufriere, St. Vincent, at altitudes between 1.8 and 5.5 kilometers were physically and chemically very similar to the ash that fell on the island. Higher altitude samples (7.3 and 9.5 kilometers) had a much lower ash content but comparable concentrations of sulfate, which were above the background concentration found at these altitudes.

Sedlacek, W. A.↗

Development of carbon slurry fuels for transportation (hybrid fuels, phase 2)

Slurry fuels of various forms of solids in diesel fuel are developed and evaluated for their relative potential as fuel for diesel engines. Thirteen test fuels with different solids concentrations are formulated using eight different materials. A variety of properties are examined including ash content, sulfur content, particle size distribution, and rheological properties. Attempts are made to determine the effects of these variations on these fuel properties on injection, atomization, and combustion processes. The slurries are also tested in a single cylinder CLR engine in both direct injection and prechamber configurations. The data includes the normal performance parameters as well as heat release rates and emissions. The slurries perform very much like the baseline fuel. The combustion data indicate that a large fraction (90 percent or more) of the solids are burning in the engine. It appears that the prechamber engine configuration is more tolerant of the slurries than the direct injection configuration.

Ryan, T. W., III↗