SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The project has two primary objectives: (1) down select three-dimensional (3D) printing and post-processing approaches for solid-state electrolyte (SSE) / cathode integration, and (2) understand battery failure mechanisms via ex situ and in situ characterization.
In the Transformational Challenge Reactor (TCR), the fuel blocks consist of an additively-manufactured silicon carbide (SiC) matrix and uranium nitride tristructural isotropic (UN TRISO) fuel particles, which are stacked to form fuel columns. The SiC matrix is manufactured using binderjet 3D printing followed by loading the TRISO fuel particles and the chemical vapor infiltration (CVI) process. Because the fuel matrix is a primary component of the TCR core and its response to mechanical and thermal loads during operation is one of the most influential factors on the integrity of TCR core, testing and evaluation have focused on producing mechanical and thermophysical properties data for the binderjet/CVI SiC. Mechanical and thermophysical properties were measured from various types of specimens printed for two or three orientations, which included equibiaxial flexural failure strength, elastic constants, thermal diffusivity and conductivity, density, and the coefficient of thermal expansion. Flexural failure strength datasets showed similar Weibull distributions regardless of sample variants including different orientations. The mean failure strengths of the 3D-printed SiC variants were in the range of 286–306 MPa, which are 22–27% lower than that of the CVD SiC. Thermophysical test results showed that specific heat and thermal expansion are not sensitive to the build directions of SiC samples, while thermal diffusivity is highly dependent on the build direction and can be correlated to the anisotropic character of the 3D-printed SiC. This report also includes discussions on the uniaxial tensile properties of the as-printed SiC before CVI and on ongoing efforts for irradiation effects studies.
A magnetic ink composition for three-dimensional (3D) printing a bonded magnet is provided. The magnetic ink composition includes magnetic particles, a polymer binder and a solvent. A 3D printing method for fabrication of a bonded magnet using the magnetic ink composition is also provided.
Solid oxide electrolysis cells (SOECs) for H 2 production is a core technology for H2@scale. However, its conventional manufacturing methods adapted from the manufacture of solid oxide fuel cells (SOFC) need high cost, especially for small-volume production. The emerging laser 3D printing (L3DP) technology with computer-aided 3D printing and computer-controlled laser processing can fulfill layer-by-layer digital shaping and rapid in-situ consolidating feedstock into complicated geometries. L3DP, a promising additive manufacturing (AM) technology, has achieved significant success in manufacturing plastic and metal parts, which is currently attracting considerable attention for the cost-effective, rapid, and flexible manufacturing of heterogeneous multilayered ceramic devices (e.g., SOECs, SOFCs, and solid-state batteries). It is believed that the L3DP can integrate the advantages of selective consolidation of heterogeneous layers, accurate control of layer microstructures, high processing heat efficiency, high processing speed, high stack compactness, high stack design flexibility, and low stack sealing area for cost-effective, rapid, and flexible manufacturing of SOECs to meet DOE’s electrolyzer target.
In this paper, we propose a teleoperated construction 3D printing technology, called TeleLayering, for planetary and terrestrial applications. The TeleLayering technology is enabled by effective multimodal control and monitoring systems and enhanced construction 3D printing robots to build or repair a variety of structures in extreme environments without the need for human presence on the jobsite. This paper presents a general description, main technical requirements, implementation challenges, and applications of this technology.
We will build a 3D printed plant growth substrate that's design is motivated by past problems faced by Vegetable Production System and anticipated problems with growing plants in microgravity based on current microgravity plant growth research.
Polyetherketoneketone (PEKK) has superior physical properties to most available thermoplastics compatible with material extrusion-based 3D printing, including analogs in the polyaryletherketone (PAEK) family. To date, the performance of fused filament fabrication (FFF) compatible PEKK has been detailed primarily as a function of varying the isomer ratios composing the co-polymer structure. The strategy to form blends or composites with PEKK for FFF is attractive for further tailoring of performance in application, yet has received limited attention. Here, we report the integration of three grades of mica platelets into PEKK at 10% and 30% mass loadings to generate an array of filament feedstocks that were then used to print objects with a simple FFF machine. The effects of mica coating chemistry and surface treatment on the compatibility with PEKK and resulting properties are described. Mica fillers at both loadings have only subtle influence on the FFF relevant melt rheological properties inherent to PEKK. Pigment micas at high loadings can lower the melting temperature of PEKK (up to 19 ºC) without shifting its glass transition temperature and inhibit much of the undesirable crystallization occurring during processing with unfilled PEKK. The printed composites were effectively cold crystallized post-printing, affording crystalline fractions up to 90% relative to unfilled PEKK with increased dimensional stabilities. All micas, when used as fillers in low and high relative PEKK crystallinities, significantly increased the tensile modulus (as high as 126% or to 7.31 GPa) of parts in correlation to the loading. Furthermore, the underlying microstructural features of a printed composite were compared to unfilled PEKK by use of a high-resolution helical micro-computed tomography instrument. Practically, pigment micas can confer a wide range of rich colors to 3D-printed PEKK.
Sustainable on-demand power solutions are an absolute necessity as humanity works to establish a permanent presence on the moon and make the journey to Mars. NASA’s SIBatt-3D Early Career Initiative project at MSFC is developing shape-conformable Sodium-Ion batteries that can be 3D printed in-space as needed during extended space missions. SIBatt-3D makes use of the unique advantages of 3D printing to create shape-conformable batteries with improved performance that reduce dead volume in devices and seeks to utilize materials found in Lunar/Martian regolith as feedstocks to provide sustainable power for surface operations on the Moon and Mars. SIBatt-3D’s batteries also have terrestrial implications such as improved battery safety and sustainability.
Anisotropy, the characteristic of materials exhibiting different properties based on their direction, is widespread in nature. Conventional manufacturing techniques often fall short in recreating such complex anisotropy. While 3D printing allows for precise fiber deposition in anisotropic composites, previous studies have only achieved bulk reorientation of fibers at the voxel level in two dimensions. This limits the replication of localized 3D anisotropies found in natural materials. To address this, a novel 3D printing technique is presented that enables subvoxel control of fiber orientation in all three directions using multidirectional shearing via nozzle rotation and inclination. The fiber orientation control in these experimental tests is driven by a numerical model, enabling a fully digital approach to program microstructures within a strand. This programmability is demonstrated through mechanical and thermal tests, illustrating a localized and controllable response to external stimuli. Achieving such complex anisotropy holds potential across several fields, including wearables and biomedical implants, lightweight composite structures, and energy storage technologies such as batteries and supercapacitors.
This data set contains images produced to test the performance of anomaly and fault detection methods in the context of additive manufacturing. Two print jobs were executed using the Ingersoll MasterPrint with the Model 30 Strangpresse extruder. The material used was Techmer compounded polylactic acid (PLA) with wood flour as a filler (80/20 PLA/WF by weight). The first print job consists of the 3D printing of a hexagonal cylinder with a two-bead wall. This print was sliced at a gantry velocity of 3000 millimeter per minute, and an extruder screw speed of 68.14 rotations per minute. This are considered the normal operating conditions. A second hexagonal cylinder was printed using a reduced extruder screw speed, 15% lower than under normal operating conditions. The images were collected with a Teledyne FLIR Lepton 3.5 infra-red camera, a small form factor radiometric long-wave infrared camera with a spectral range of 8 µm to 14 µm. Sensor resolution was 160x120 pixels, with a pixel size of 12 µm, a temperature range of -10 - 450°C, and an accuracy of +/- 10°C in its low gain configuration. Images in this data set were collected with cameras oriented at the printer nozzle. The nozzle camera setup consisted of two cameras located 12.5cm from the nozzle center. These were mounted directly to the print head, so that the camera positions relative to the print direction would remain constant as it rotated around its C-axis to follow the print path. One camera was placed ahead of the nozzle to capture the previous layer immediately before being covered by the new layer of material, while the second camera was placed behind the nozzle and captured the freshly extruded bead. Images are collecting during each phase of the print: (a) idle (i.e., no material deposited), (b) extrusion (i.e., to prime the extruder), and (c) printing (deposition of material to manufacture the hexagonal cylinder).
High areal capacity electrodes hold great potential for high-energy density lithium-ion batteries (LIBs), but their poor electrochemical kinetics limit their power density. Here, in this study, high areal capacity 3D-structured LiNi 0.8 Mn 0.1 Co 0.1 O 2 cathodes (4.3 mAh cm -2 ) are prepared via 3D printing with a manner of direct ink writing. The electrodes had an enlarged electrode–electrolyte contact area, shortened diffusion pathway, and reduced intercalation-induced stress, thereby delivering enhanced rate capability and cyclability in LIBs, which is 143.6 mAh g -1 at 3C and a 60.2 % capacity retention over 800 cycles at 1C. Moreover, at electrode level, the 3D-NMC exhibits an energy and power densities of 313.1 Wh kg -1 and 657.9 W kg -1 , respectively. Furthermore, the theoretical calculation suggests that reducing the gap width will be highly beneficial to the energy and power densities. This work establishes a milestone in understanding the cycling effect on the electrode local structure, including the void area and the LiNi 0.8 Mn 0.1 Co 0.1 O 2 region, which confirms the effectiveness of 3D printing for electrode preparation.
To dramatically increase the adaptability, performance, and safety of processes in support of the Defense Waste Processing Facility (DWPF), Savannah River National Lab (SRNL) plans to perform chemical and radiological compatibility testing on a wide variety of 3D printed materials of interest. The 3D printing process provides numerous strategic operational benefits such as rapid prototyping of complex designs and geometry specific to the needs of the nuclear waste disposition process, as well as on-demand rapid prototyping and iteration with materials that aren’t as accessible through traditional manufacturing methods. Reaction chemistry in simulated waste batches can be matched closely to its radioactive counterpart, but glass reactor vessels have limitations. Vessel geometry can play a big factor in mixing transport limitations, process chemistry, and degradation reaction kinetics. In addition, additive manufacturing allows for much more detailed vessel design than traditional alternatives. Waste processing techniques in DWPF also encounter extreme chemical environments including high pH, strong acids, abrasive slurries, and significant irradiation. To meet these challenges, a matrix of various polymer, ceramic, and metal additive manufacturing materials have been exposed to a suite of chemical environments of interest as well as radioactive dose (such as gamma radiation from 60 Co) to properly test their durability under these conditions. Mass change has been monitored over a period of up to a week in these conditions, as well as added characterization for surface modification through Scanning Electron Microscopy/Electron Dispersive X-ray analysis (SEM/EDX). Further chemical characterization has been monitored through Fourier-Transform InfraRed Spectroscopy (FTIR), with planned investigation via thermal and tensile strength degradation. While the direct product of this research is identification of material(s) that can withstand specific hazardous environments encountered by the mercury water wash tank in DWPF process simulation experiments, the reference base of materials will be used for many other nuclear processes in the pursuit of rapidly developed, cost-efficient, and highly specific devices for environmental remediation and much more.
The energy transition is one of the main challenges of our society and therefore a major driver for the scientific community. To ensure a smart transition to a sustainable future energy scenario different technologies such as energy harvesting using solar cells or windmills and chemical storage in batteries, super-capacitors or hydrogen have to be developed and ultimately deployed. New fabrication approaches based on additive manufacturing and the digitalization of the industrial processes increase the potential to achieve highly efficient and smart technologies required to increase the competitiveness of clean energy technologies against fossil fuels. In this frame, the present roadmap highlights the tremendous potential of 3D printing as a new route to fully automate the manufacturing of energy devices designed as digital files. Additionally, this article gives numerous guidelines to maximize the performance and efficiency of the next generation of 3D printed devices for the energy transition while reducing the waste of critical raw materials. In particular, the paper is focused on the current status, present challenges and the expected and required advances of 3D printing for the fabrication of the most relevant energy technologies such as fuel cells and electrolysers, batteries, solar cells, super-capacitors, thermoelectric generators, chemical reactors and turbomachinery.
This study primarily focuses on examining the impact that geometric structure has on thermal conductivity of multi-phase constructs in different 3D-printed poly(lactic acid), PLA, samples. The investigated structures are inspired by morphologies formed by diblock copolymers: lamellae, hexagonally packed cylinders, and gyroid. This research also investigates how volume percentage and material combination influence the thermal conductivity of these structures. Further, the samples can be tailored to simulate various thermal management structures observed in practical applications, such as thermal interface materials in electronic devices. Thermal conductivity ratio is controlled using air, the least conductive material at 0.026 W/(m K), PLA at 0.136 W/(m K), and thermal paste at 5.11 W/(m K). Different models were tested against thermal conductivity measurements in order to capture the effect of material type (PLA-Air versus PLA-Thermal Paste), volume percentage, structure, and orientation. Simple, effective medium models were good predictions of thermal conductivity in lamellar structures, but it was necessary to develop models for conduction through cylindrical and gyroid structures. Finally, all results were normalized to find a universal model that is independent of structure and material. This approach provides a simple method to predict how to reduce or enhance transport properties and heat management capabilities of 3D printed objects.
Eight chromophoric indicators are incorporated into Sylgard 184 to develop sensors that are fabricated either by traditional methods such as casting or by more advanced manufacturing techniques such as 3D printing. The sensors exhibit specific color changes when exposed to acidic species, basic species, or elevated temperatures. Additionally, material properties are investigated to assess the chemical structure, Shore A Hardness, and thermal stability. Comparisons between the casted and 3D printed sensors show that the sensing devices fabricated with the advanced manufacturing technique are more efficient because the color changes are more easily detected.
The NGEE Arctic Rainfall Simulator (NARS) is a variable intensity rainfall simulator (RFS) with a frame design based on the Humphry et al. (2002) RFS and a water delivery system based on the Walnut Gulch (Paige et al., 2004) RFS. The NARS uses an aluminum frame that is fully deconstructable for transportation to field locations and a water system that enables variable rain intensity. Prior to field deployment, H-flume discharge and the corresponding Milone eTape Liquid Level Sensor (eTape) resistance values were measured in the laboratory so that discharge measurements from the NGEE Arctic Rainfall Simulator could be automated. eTape resistance was measured with increasing fluid heights for the full range of the eTape to calculate sensor detection limits and resolution. The eTape was calibrated to both a commercially available 12.2 cm HS-flume and a 3D printed 4 cm Micro-HS-flume. This data package contains two .csv files, one for the eTape calibration and the other for the flume calibrations, and two .stl files to 3D print the 4 cm Micro-HS-Flume design with a 1 cm x 3.6 cm stilling well opening. The .stl files can be opened in most 3D printing or CAD programs/software. Two .kml files of the laboratory location and broader area where testing was conducted are also included in this data package.The Next-Generation Ecosystem Experiments: Arctic (NGEE Arctic), was a research effort to reduce uncertainty in Earth System Models by developing a predictive understanding of carbon-rich Arctic ecosystems and feedbacks to climate. NGEE Arctic was supported by the Department of Energy's Office of Biological and Environmental Research.The NGEE Arctic project had two field research sites: 1) located within the Arctic polygonal tundra coastal region on the Barrow Environmental Observatory (BEO) and the North Slope near Utqiagvik (Barrow), Alaska and 2) multiple areas on the discontinuous permafrost region of the Seward Peninsula north of Nome, Alaska.Through observations, experiments, and synthesis with existing datasets, NGEE Arctic provided an enhanced knowledge base for multi-scale modeling and contributed to improved process representation at global pan-Arctic scales within the Department of Energy's Earth system Model (the Energy Exascale Earth System Model, or E3SM), and specifically within the E3SM Land Model component (ELM).
Disruptive robotic construction technologies such as additive deposition of cementitious materials like concrete (or "3D concrete printing") require the synchronous operation of multiple pieces of equipment in the production setup. In such an environment, it is crucial to simulate the robotic motions (for toolpath clashes) and the cementitious material behavior (for toolpath failures) to ensure fail-proof constructability of the envisioned building geometry. However, toolpath clash detection requires 4D simulations of the production setup, which are computationally graphics intensive, whereas toolpath failure detection requires actual 3D printing of test parts from the geometry to identify areas prone to failure while 3D printing, which is physically tedious. Both these processes, being computationally and physically intensive, have largely curtailed designers from simulating and exploring large sets of design options with varying geometries and toolpath configurations. To overcome this and allow designers to explore large sets of design possibilities, this paper proposes two novel computational metamodels capable of performing robotic toolpath clash detection and failure detection with significantly reduced times than the earlier approaches. The developed metamodels were used to rapidly simulate large sets of building design options for robotic constructability in the NASA 3D-Printed Mars Habitat Challenge.
Research on polymer materials for additive manufacturing technology in biomedical applications is as promising as it is numerous, but biocompatibility of printable materials still remains a big challenge. Changes occurring during the 3D-printing processes itself may have adverse effects on the compatibility of the completed print. Furthermore, this prospective will put emphasis on the different additives and processes that can have a direct impact on biocompatibility during and after 3D printing of polymer materials.