SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Shock tube data are used to examine the systematic f value behavior in prominent visible transition arrays (ns-np, np-(n+l)s, np-nd) for the homologous emitter sequence Si 11, Ge 11, Sn 11, and Pb 11. Regularities found for these data are compared with trends in lighter elements. Agreements and s disparities with theoretical and experimental oscillator strengths from the literature are noted.
This report describes the ultrasonic-acoustic technique used to measure a 'Stress Wave Factor'. In a prior study this factor was found effective in evaluating the interlaminar shear strength of fiber-reinforced composites. Details of the method used to measure the stress wave factor are described. In addition, frequency spectra of the stress waves are analyzed in order to clarify the nature of the wave phenomena involved. The stress wave factor can be measured with simple contact probes requiring only one-side access to a part. This is beneficial in nondestructive evaluations because the waves can run parallel to fiber directions and thus measure material properties in directions assumed by actual loads. Moreover, the technique can be applied where conventional through transmission techniques are impractical or where more quantitative data are required. The stress wave factor was measured for a series of graphite/polyimide composite panels and results obtained are compared with through transmission immersion ultrasonic scans.
An experimental investigation was conducted to evaluate the effect of low-velocity impact damage on the compression strength of filamentary-composite hat-stiffened panels. Twenty-four specimens of three design configurations fabricated from graphite-epoxy and boron-epoxy materials were tested. All three design configurations met the design buckling requirements in the undamaged condition. The impact damage was caused by firing aluminum spheres at the panels to simulate impact on aircraft from runway stones. Panels were damaged by impact in the hat cap or in the skin beneath the hat cap (regions of high axial stiffness) and in the skin between stiffeners (region of low axial stiffness). The panels were relatively insensitive to impact damage in the regions of low axial stiffness but were very sensitive to impact damage in the regions of high axial stiffness. Test results suggest that impact damage may be more dependent on the matrix properties than on the fiber properties of the composite materials considered.
On the basis of conservative assumptions, a phenomenological approach is used to address the source strength of Jupiter for interplanetary electrons. It is estimated that Jupiter emits approximately 10 to the 24th - 10 to the 26th electrons per sec with energies in excess of 6 MeV, which sources may be compared with the population of approximately 3 x 10 to the 28th electrons of the same energy in the Jovian outer magnetosphere. It is concluded that Jupiter accelerates particles at a rate exceeding that of ordinary trapped particle dynamic processes.
Three test schemes were examined for testing graphite/epoxy (Narmco T300/5208) composite material specimens to failure in compression, including an adaptation of the IITRI "wedge grip" compression fixture, a face-supported-compression fixture, and an end-loaded-coupon fixture. The effects of specimen size, specimen support arrangement and method of load transfer on compressive behavior of graphite/epoxy were investigated. Compressive stress strain, strength, and modulus data obtained with the three fixtures are presented with evaluations showing the effects of all test parameters, including fiber orientation. The IITRI fixture has the potential to provide good stress/strain data to failure for unidirectional and quasi-isotropic laminates. The face supported fixture was found to be the most desirable for testing + or - 45 s laminates.
An iron alloy is provided which exhibits strength and toughness characteristics at cryogenic temperatures. The alloy consists essentially of about 10 to 16 percent by weight nickel, about 0.1 to 1.0 percent by weight aluminum, and 0 to about 3 percent by weight copper, with the balance being essentially iron. The iron alloy is produced by a process which includes cold rolling at room temperature and subsequent heat treatment.
A study of the flow strength, creep resistance and diffusion welding characteristics of the titanium alloy Ti-6Al-2Nb-1Ta-0.8Mo has been conducted. Two mill-processed forms of this alloy were examined. The forged material had been processed above the beta transus (approximately 1275 K) while the rolled form had been subjected to work below the beta transus. Between 1150 and 1250 K, the forged material was stronger and more creep resistant than the rolled alloy. Both forms exhibit superplastic characteristics in this temperature range. Strain measurements during diffusion welding experiments at 1200 K reveal that weld interfaces have no measurable effect on the overall creep deformation. Significant deformation appears to be necessary to produce a quality diffusion weld between superplastic materials. A 'soft' interlayer inserted between faying surfaces would seemingly allow manufacture of quality diffusion welds with little overall deformation.
Selected lines in the 4-0 and 5-0 bands of HD have been studied with absorption paths up to 80 m and densities up to 0.76 amagat at laboratory temperature. The strengths of these lines are of particular interest in the study of the atmospheres of the outer planets.
Shock-tube data are used to examine systematic f-value behavior in prominent visible transition arrays for the homologous emitter sequence Si-II, Ge-II, Sn-II, and Pb-II. Regularities found in these data are compared with trends in lighter elements. Agreements and disparities with theoretical and experimental oscillator strengths from existing literature are noted.
Measurements of the oscillator strengths of the ultraviolet lines of neutral nickel obtained by the use of the combined hook and absorption technique are reported. A total of 221 transitions in the range 1964-4094 A was measured for nickel atoms from a high-temperature graphite furnace (2000-2500 K) using a continuum background source, a Mach-Zehnder interferometer and a 3-m Czerny-Turner spectrograph. Hook and absorption measurements are presented, and radiative lifetimes are derived from log gf values. Comparison of the present values with previous results indicates only those of Bell et al. (1966) and Lennard et al. (1975) to consistently agree with the data presented, although the reliability laser-excitation technique of lifetime measurement is supported over that of Hanle methods.
A nickel-based powder metal disk alloy developed for use in advanced commercial gas turbines is described. Consideration is given to final alloy chemistry modifications made to achieve a desirable balance between tensile strength and stress rupture life and ductility. The effects of post-consolidation heat treatment are discussed, the preliminary mechanical properties obtained from full-scale turbine disks are presented.
Simplified convenient procedure has been developed that can be used to determine elastic and strength properties of angle-plied laminates. Method is suitable for use with pocket calculator. Consists of simple equations and graphs of ply combinations from most frequently used composites. Procedure makes use of well-known transformation equations, ply stress influence coefficients, and ply uniaxial composites including interply and intraply hybrids.
To develop predictive theory to account for time/temperature effect of B/A1 composites, series of deformation and fracture studies was performed on commercial boron fibers over wide ranges of stress, stress application time, and temperature. By combining these single fiber results with fracture theory for metal matrix composites, design formulas were derived that describe B/A1 composite tensile and stress rupture strengths as function of time and temperature. Using derived formulas, calculated and experimental results agree to within 3 percent.
A theory of the effect of geometry on the mechanical properties of a butt weld joint is worked out based upon the soft interlayer weld model. Tensile tests of 45 TIG butt welds and 6 EB beads-on-plate in 1/4-in. 2219-T87 aluminum plate made under a wide range of heat sink and power input conditions are analyzed using this theory. The analysis indicates that purely geometrical effects dominate in determining variations in weld joint strength with heat sink and power input. Variations in weld dimensions with cooling rate are significant as well as with power input. Weld size is suggested as a better indicator of the condition of a weld joint than energy input.
A diamond surface undergoes a transformation in its electronic structure by a vacuum anneal at approximately 900 C. The polished surface has no electronic states in the band gap, whereas the annealed surface has both occupied and unoccupied states in the and gap and exhibits some electrical conductivity. The effect of this transformation on the strength of the diamond metal interface was investigated by measuring the static friction force of an atomically clean meta sphere on a diamond flat in ultrahigh vacuum. It was found that low friction (weak bonding) is associated with the diamond surface devoid of gap states whereas high friction (strong bonding) is associated with the diamond surface with gap states. Exposure of the annealed surface to excited hydrogen also leads to weak bonding. The interfacial bond is discussed in terms of interaction of the metal conduction band electrons with the band gap states on the diamond surface. Effects of surface electrical conductivity on the interfacial bond are also be considered.
It has long been known that the periods of Pc 3, 4 pulsations on the ground correlate with the magnitude of the interplanetary magnetic field. This fact has been used to argue for an exogenic source for these pulsations. Particularly attractive candidates for the source of pulsations in this frequency range are the upstream waves of similar frequencies which are associated with populations of ions reflected from the bow shock. However, the dependence of the period of these waves on the strength of the interplanetary magnetic field has never been checked. This paper performs such a check and confirms that the upstream waves have the proper functional relationship.
Fatigue initiation in six aluminum alloys used in the aircraft industry was investigated. Cyclic loading superimposed on a constant stress was alternated with atmospheric corrosion. Tests made at different stress levels revealed that a residual stress as low as 39% of the yield strength caused stress corrosion cracking in some of the alloys. An atmospheric corrosion rate meter developed to measure the corrosivity of the atmosphere is described. An easily duplicated hole in the square test specimen with a self-induced residual stress was developed.
Experimental results are presented showing that the strength and toughness of finite width angle-ply laminates can be increased significantly by using an alternating layer stacking sequence as opposed to a clustered configuration. The ultimate tensile stress of an alternating plus/minus theta laminate of the form (+ or - theta) sub 2 sub s can be much as 1.5 times that of a clustered configuration of the form theta sub 2/-theta sub 2 sub s. Further, the toughness of the alternating layer configuration can be as much as 2.7 times that of the clustered configuration. These differences are explained analytically through consideration of the influence of layer thickness on the magnitude of the interlaminar shear stress and by examination of failed specimens. It is shown that the two laminate configurations exhibit distinctly different failure modes for some fiber angles. Both laminate configurations exhibit catastrophic failure with the damage limited essentially to a small region defined by the length of a single crack across the width of the specimen, parallel to the fiber direction. Results are presented for T300/5208 graphite-epoxy for fiber orientations of 10, 30, and 45 deg.