Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “load shapes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,603 records · Page 89

Generation of graphite particles by sliding abrasion and their characterization

Characterization of graphite particles (dust) produced by abrasion that would occur in a pebble bed reactor is of interest for reasons of safety, operation, and maintenance. To better understand this abrasion and particle generation, we have built a test apparatus to produce particles by sliding abrasion in a 1% to 5% relative humidity air environment. We have used a commercial-grade graphite in our experiments and have generated size distributions for the abraded particles. We have also fit lognormal functions to those size distributions (for use in computer codes); determined particle shapes; measured temperature and humidity during the tests; measured and calculated wear rates; and measured the surface roughness of both pretest and posttest samples, particle surface areas, pore volumes, and pore volume distributions of particles produced during abrasion of graphite surfaces under different loadings and sliding speeds. The experiments showed that as loading (analogous to pebble depth in the reactor) and sliding speed increase, so do the wear rates and numbers of particles produced, while surface roughness decreases, increases, and then decreases. Brunauer-Emmett-Teller measurements show that abrasion increases surface area from 0.583 m 2 /g in the bulk material to 555 m 2 /g in material abraded at high loading and high sliding speed. Wear rates range from 0.005 to 0.991 g/m per contact site. As a result, the size of the particles observed was <4000 nm. Finally, in all, our research shows that pebble abrasion is a complex process that is not constant during operation and thus should be considered for future work.

36 MATERIALS SCIENCE↗

Development of a Planar Focusing Collector for CSP

In the field of the concentrating solar power (CSP) technology, the parabolic trough is a common choice for a solar collector. Parabolic troughs are highly reflective curved mirrors that take incident sunlight and focus it onto a line-shaped receiver that runs down the center of troughs. The receivers are generally heat-absorbing pipes containing a heat transfer fluid that delivers the collected thermal energy to steam turbines or engines for generating electricity. However, parabolic troughs are constrained by wind loads and cost of materials and support structure. The goal of this project was to develop a planar focusing collector (PFC) that would serve as an alternative to the parabolic trough. An ideal PFC is ultrathin (less than a few microns) and lightweight, and could be manufactured in a manner that is scalable and low cost. Furthermore, these features would be attractive to CSP technology because of the potential to reduce cost and complexity of installation and maintenance. The work pursued in this project attempted to actualize the PFC concept by utilizing advances in the emerging area of metasurfaces, which rely on the nanopatterning of surfaces to control the amplitude and phase of light at length scales smaller than an optical wavelength. Academic pursuits of metasurface technology predominately employ electron-beam lithography (EBL) for fabrication because the technique offers highly reliable nanopatterning of surfaces with a spatial resolution of ~10 nm. However, due to the techno-economic constraints of the DOE’s SunShot program, particularly cost-effective scalability, the use of EBL was avoided in this project. Rather, fabrication approaches that lend themselves to scalable manufacturing by way of stamping or imprinting were favored. Ultimately, the tradeoffs with using such methods was the larger feature size—on the order of ~150 um critical dimension—resulting in poorer control of light compared to structures fabricated by EBL. A summary of our 2-year investigation on this topic is presented herein. We begin by presenting highlights of our 1 st -year efforts using plasmonics, i.e., metallic nanostructures, as the building block for our PFC. The limitations in this approach are subsequently summarized. We then review the strategy we employed during the final year of our project, in particular utilizing insulating or dielectric materials as the light controlling medium. We round out the report discussing the results of our findings from using this approach. The report is relatively self-contained in that and no prior knowledge of optics or nanotechnology is assumed and technical jargon is kept at a minimum.

14 SOLAR ENERGY↗

In Situ Monitoring of Direct Ink Write Process Using Electromagnetic Resonant Coupling

Additive manufacturing (AM) of multi-material objects enables the design of complex 3D architectures such as printed electronics and devices. The ability to detect the composition of multi-material printed inks in real time is an emerging need for a wide range of manufacturing applications. This study demonstrates the feasibility of using an in situ sensor to locally measure the composition of inks as they are being printed to facilitate greater control over the resulting properties and functionality of printed materials. Dielectric properties of microscale embedded metal particles in a dielectric matrix are measured and characterized as a function of particle size, shape, volume percentage and frequency. Results show that particle shape has a much greater influence on impedance measurements than the particle size. Measurements are found to agree with calculations based on an anisotropic Maxwell-Garnett dielectric function model. The resulting data can be used to generate a calibration curve correlating metal loading with impedance or capacitance and thus applied as an in situ sensor for compositional measurements during extrusion-based AM.

36 MATERIALS SCIENCE↗

C-shaped specimen plane strain fracture toughness tests

Test equipment, procedures, and data obtained in the evaluation of C-shaped specimens are presented. Observations reported on include: specimen preparation and dimensional measurement; modifications to the standard ASTM E 399 displacement gage, which permit punch mark gage point engagement; and a measurement device for determining the interior and exterior radii of ring segments. Load displacement ratios were determined experimentally which agreed with analytically determined coefficients for three different gage lengths on the inner surfaces of radially-cracked ring segments.

Buzzard, R. T.↗

Vibration analysis of the Long Duration Exposure Facility (LDEF) using SPAR

The structural modeling of the Long Duration Exposure Facility (LDEF) utilizing the SPAR system of computer programs for vibration analysis is discussed. The technical areas of interest were: (1) development of the LDEF finite element model; (2) derivation of tray effective panel stiffness matrix using finite element tray models; (3) assessment of attachment conditions and end fitting flexibility by comparing SPAR with test static displacements; (4) SPAR grouping; and (5) derivation of the LDEF frequencies and mode shapes and comparing them with tests. Special detailed finite element modeling was required to obtain good agreement between analytical and test vibration modes. An orthotropic panel in the overall model was developed. Orthotropic stiffness for this panel were obtained from finely detailed statically loaded SPAR models which included stiffness and allowed for partial relative sliding of the tray clamping attachments. Sensitivity to LDEF joint boundary conditions was determined, and static test data proved valuable in assessing modeling of local end fittings.

Edighoffer, H.↗

On the shape and orientation control of an orbiting shallow spherical shell structure

A proposed method for controlling the shape and orientation of very large shallow dish type receiver/reflectors to be used in communication, radiometry and in electronic orbital based mail systems involves connecting a rigid light weight dumbell with heavy tip masses to the shell at its apex by a spring loaded double gimballed joint with dampling. To completely damp the system transient motion in all of the important lower frequency modes, an active control system is required. A mathematical model is extended to include the effects of point actuators located at preselected positions on the shell surface. The formulation of the uncontrolled dynamics assumes an a priori knowledge of the frequencies of all the elastic modes to be incorporated within the system model. As an example, three rigid body modes and six elastic modes are included in the model and six actuators are assumed, none of which lies on a nodal line or circle.

Bainum, P. M.↗

The tectonics of Mercury

The probable tectonic history of Mercury and the relative sequence of events are discussed on the basis of data collected by the Mariner-10 spacecraft. Results indicate that Mercury's tectonic activity was confined to its early history; its endogenic activity was principally due to a small change in the shape of its lithosphere, caused by tidal despinning, and a small change in area caused by shrinkage due to cooling. Exogenic processes, in particular the impact activity, have produced more abundant tectonic features. Many features associated with the Caloris basin are due to loading of Mercury's thick lithosphere by extrusive lavas or subsidence due to magma withdrawal. It is emphasized that tectonic features observed on Mercury yield insight into the earliest tectonic events on planets like Mars and, perhaps, the earth, where subsequent events obscured or erased the most ancient tectonic records.

Melosh, H. J.↗

Advanced Technology Blade testing on the XV-15 Tilt Rotor Research Aircraft

The XV-15 Tilt Rotor Research Aircraft has just completed the first series of flight tests with the Advanced Technology Blade (ATB) rotor system. The ATB are designed specifically for flight research and provide the ability to alter blade sweep and tip shape. A number of problems were encountered from first installation through envelope expansion to airplane mode flight that required innovative solutions to establish a suitable flight envelope. Prior to operation, the blade retention hardware had to be requalified to a higher rated centrifugal load, because the blade weight was higher than expected. Early flights in the helicopter mode revealed unacceptably high vibratory control system loads which required a temporary modification of the rotor controls to achieve higher speed flight and conversion to airplane mode. The airspeed in airplane mode was limited, however, because of large static control loads. Furthermore, analyses based on refined ATB blade mass and inertia properties indicated a previously unknown high-speed blade mode instability, also requiring airplane-mode maximum airspeed to be restricted. Most recently, a structural failure of an ATB cuff (root fairing) assembly retention structure required a redesign of the assembly. All problems have been addressed and satisfactory solutions have been found to allow continued productive flight research of the emerging tilt rotor concept.

Wellman, Brent↗

Investigation of Injector Slot Geometry on Curved-Diffuser Aerodynamic Performance

The Compressor Branch vision is to be recognized as world-class leaders in research for fluid mechanics of compressors. Its mission is to conduct research and develop technology to advance the state of the art of compressors and transfer new technology to U.S. industries. Maintain partnerships with U.S. industries, universities, and other government organizations. Maintain a balance between customers focused and long range research. Flow control comprises enabling technologies to meet compression system performance requirements driven by emissions and fuel reduction goals (e.g., in UEET), missions (e.g., access-to-space), aerodynamically aggressive vehicle configurations (e.g., UAV and future blended wing body configurations with highly distorted inlets), and cost goals (e.g., in VAATE). The compression system requirements include increased efficiency, power-to-weight, and adaptability (i.e., robustness in terms of wide operability, distortion tolerance, and engine system health and reliability). The compressor flow control task comprises efforts to develop, demonstrate, and transfer adaptive flow control technology to industry to increase aerodynamic loading at current blade row loss levels, to enable adaptive1 y wide operability, and to develop plant models for adaptive compression systems. In this context, flow control is the controlled modification of a flow field by a deliberate means beyond the natural (uncontrolled) shaping of the solid surfaces that define the principal flow path. The objective of the compressor flow control task is to develop and apply techniques that control circulation, aerodynamic blockage, and entropy production in order to enhance the performance and operability of compression systems for advanced aero-propulsion applications. This summer I would be working with a curved-diffuser because it simulates what happens with flow in the stator blades in the compressor. With this experiment I will be doing some data analysis and parametric study of the injector slot geometries to get the best aerodynamic performance of it. This includes some data reduction, redesign and fast prototyping of the injector nozzle.

Silva, Odlanier↗

Fracture Analysis of Particulate Reinforced Metal Matrix Composites

A fracture analysis of highly loaded particulate reinforced composites was performed using laser moire interferometry to measure the displacements within the plastic zone at the tip of an advancing crack. Ten castings were made of five different particulate reinforcement-aluminum alloy combinations. Each casting included net-shape specimens which were used for the evaluation of fracture toughness, tensile properties, and flexure properties resulting in an extensive materials properties data. Measured fracture toughness range from 14.1 MPa for an alumina reinforced 356 aluminum alloy to 23.9 MPa for a silicon carbide reinforced 2214 aluminum alloy. For the combination of these K(sub Ic) values and the measured tensile strengths, the compact tension specimens were too thin to yield true plane strain K(sub Ic) values. All materials exhibited brittle behavior characterized by very small tensile ductility suggesting that successful application of these materials requires that the design stresses be below the elastic limit. Probabilistic design principles similar to those used with ceramics are recommended when using these materials. Such principles would include the use of experimentally determined design allowables. In the absence of thorough testing, a design allowable stress of 60 percent of the measured ultimate tensile stress is recommended.

Min, James B.↗

Hypervelocity Impact Performance of 3D Printed Aluminum Panels

With the continued development of additive manufacturing methods, control over the shape of ligaments, cell regularity, and macroscopic shape can all be easily tuned. This capability allows for tailoring of component architecture and promotes potential mass savings in a space vehicle structure. Additionally, it allows one the flexibility of combining structural elements such as MMOD protection and vehicle stiffness for launch loads for an overall mass reduction. At NASA JSC this technology is being explored in many different ways with the goal being a multifunctional structural component. For this study, four different types of aluminum panels have been 3D printed for testing, three being of a body centric cubic (BCC) lattice structure core and one being kelvin cell structure core. All samples have a 5.33 cm (0.05”) nominally thick aluminum face sheet printed on the front and back side of each panel, with all core materials having a 5.08 cm (2.0”) nominal thickness (see Table 1 for test sample summary and Figures 1 – 2 for sample illustrations). These tests will evaluate the performance of 3D printed aluminum panels under hypervelocity impact (HVI) conditions. The hypervelocity impact tests are being conducted at the JSC White Sands Test Facility (WSTF) Remote Hypervelocity Test Laboratory (RHTL), located in Las Cruces, New Mexico. All tests will be conducted with a 3.4mm Al 2017-T4 sphere at 6.8 km/s impacting at 0° to surface normal (i.e., impacting with no obliquity). Each sample will be trapped between two metal frames, with gasket material residing between the sample and frame, which will be the shipping and testing configuration for all tests. There will be an Al 2017-T4 witness plate staged 5.08 cm (2.0”) from each sample to capture signature of debris, if the rear face sheet of the sample were to perforate from the HVI test event.

Davis, B. A.↗

TPSAS-NF1676L-13539-DND

The performance of variable stiffness composite panels is characterized using experiments and structural analyses. Fabricated using a fiber placement system, the fiber angle in these panels varies continuously within each ply. Measured panel shapes and thermal responses are correlated with finite element analyses. Large geometric imperfections require unique fixtures to both straighten the panel edges and provide structural test boundary conditions. Panels show linear prebuckling and nonlinear postbuckling under applied end shortening, which occur at higher loads than a baseline panel. Panel responses to in-plane loading are computed using geometric and materially nonlinear analyses that include mechanical prestresses and measured imperfections. Analytical strains and displacements also correlate well with measured results.

Chauncey Wu↗

On the Influence of the Heat Treatment Temperature on the Superelastic Compressive Behavior of the Ni-Rich NiTi Shape Memory Alloy

In this paper, the relationship between the heat treatment temperature and the thermomechanical behavior of the Ni-rich NiTi shape memory alloy was experimentally investigated. Thermal analysis was performed through a differential scanning calorimetry experiments, and the NiTi superelastic effect was exhibited through loading/unloading compression cycle. It was found that the transformation temperatures and the compressive mechanical response are strongly affected by the heat treatment temperatures. The stress-induced phase transformation was characterized through the relationship between the heat treatment temperature and transformation stresses, elastic moduli and the deformation level upon loading. Subsequently, the evolution of the mechanical hysteresis loops and the mechanical dissipated energy was discussed. The obtained findings are supported by hardness measurements. To better understand the global tendency of the various phase transformation stages, the critical stress-temperature diagram was provided for different proposed heat treatment temperatures.

36 MATERIALS SCIENCE↗

Soft recovery technique to investigate dynamic fragmentation of laser shock-loaded metals

With the development of high energy laser facilities dedicated to inertial confinement fusion, the question of debris ejection from metallic shells subjected to intense laser irradiation has become a key issue. We have used two diagnostics to investigate fragmentation processes. Recovery of ejected fragments has been performed in a highly transparent gel of density 0.9 g/cm{sup 3}. Fragments sizes, shapes, and penetration depths, can be easily observed with a spatial resolution of micrometer-order. Complementary data are provided by transverse shadowgraphy which allows to obtain quasi-instantaneous, successive pictures of the debris clouds and mean ejection velocities.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

A Common Probe Design for Multiple Planetary Destinations

Atmospheric probes have been successfully flown to planets and moons in the solar system to conduct in-situ measurements. They include the Pioneer Venus multi-probes, the Galileo Jupiter probe, and Huygens probe. Probe mission concepts to five destinations, including Venus, Jupiter, Saturn, Uranus, and Neptune, have all utilized similar-shaped aeroshells and concept of operations, namely a 45 deg sphere cone shape with high density heatshield material and parachute system for extracting the descent vehicle from the aeroshell. Each concept designed its probe to meet specific mission requirements and to optimize mass, volume, and cost. At the 2017 IPPW, NASA Headquarters postulated that a common aero-shell design could be used successfully for multiple destinations and missions. This "common probe" design could even be assembled with multiple copies, properly stored, and made available for future NASA missions, potentially realizing savings in cost and schedule and reducing the risk of losing technologies and skills difficult to sustain over decades. Thus the NASA Planetary Science Division funded a study to investigate whether a common probe design could meet most, if not all, mission needs to the five planetary destinations with extreme entry environments. The Common Probe study involved four NASA Centers and addressed these issues, including constraints and inefficiencies that occur in specifying a common design.Study methodology: First, a notional payload of instruments for each destination was defined based on priority measurements from the Planetary Science Decadal Survey. Steep and shallow entry flight path angles (EFPA) were defined for each planet based on qualification and operational g-load limits for current, state-of-the-art instruments. Interplanetary trajectories were then identified for a bounding range of EFPA. Next, 3-DoF simulations for entry trajectories were run using the entry state vectors from the interplanetary trajectories. Aeroheating correlations were used to generate stagnation point convective and radiative heat flux profiles for several aeroshell shapes and entry masses. High fidelity thermal response models for various TPS materials were used to size stagnation point thicknesses, with margins based on previous studies. Backshell TPS masses were assumed based on scaled heat fluxes from the heatshield and also from previous mission concepts.

Hwang, Helen H.↗

Reliability-Based Design Optimization of a Composite Airframe Component

A stochastic design optimization methodology (SDO) has been developed to design components of an airframe structure that can be made of metallic and composite materials. The design is obtained as a function of the risk level, or reliability, p. The design method treats uncertainties in load, strength, and material properties as distribution functions, which are defined with mean values and standard deviations. A design constraint or a failure mode is specified as a function of reliability p. Solution to stochastic optimization yields the weight of a structure as a function of reliability p. Optimum weight versus reliability p traced out an inverted-S-shaped graph. The center of the inverted-S graph corresponded to 50 percent (p = 0.5) probability of success. A heavy design with weight approaching infinity could be produced for a near-zero rate of failure that corresponds to unity for reliability p (or p = 1). Weight can be reduced to a small value for the most failure-prone design with a reliability that approaches zero (p = 0). Reliability can be changed for different components of an airframe structure. For example, the landing gear can be designed for a very high reliability, whereas it can be reduced to a small extent for a raked wingtip. The SDO capability is obtained by combining three codes: (1) The MSC/Nastran code was the deterministic analysis tool, (2) The fast probabilistic integrator, or the FPI module of the NESSUS software, was the probabilistic calculator, and (3) NASA Glenn Research Center s optimization testbed CometBoards became the optimizer. The SDO capability requires a finite element structural model, a material model, a load model, and a design model. The stochastic optimization concept is illustrated considering an academic example and a real-life raked wingtip structure of the Boeing 767-400 extended range airliner made of metallic and composite materials.

Patnaik, Surya N.↗

Investigation of Atmospheric Boundary-Layer Effects on Launch-Vehicle Ground Wind Loads

A launch vehicle ground-wind-loads program is underway at the NASA Langley Transonic Dynamics Tunnel. The objectives are to quantify key aerodynamic and structural characteristics that impact the occurrence of large wind-induced oscillations of a launch vehicle when exposed to ground winds prior to launch. Of particular interest is the dynamic response of a launch vehicle when a von Kármán vortex street forms in the wake of the vehicle resulting in quasiperiodic lift and drag forces. Vehicle response to these quasiperiodic forces can become quite large when the frequency of vortex shedding nears that of a lowly-damped structural mode thereby exciting a resonant response. Wind approaching the vehicle can be characterized by a varying speed with height and turbulence content. The combination of both the varying speed and turbulence content is referred to herein as the atmospheric boundary-layer. The importance of the atmospheric boundary-layer upon launch vehicle wind-induced oscillation response has long been questioned, and its effects are not well understood. Although there are several facilities around the world dedicated to replicating atmospheric boundary layers, the development of such a boundary layer in a wind tunnel capable of producing flight-representative Reynolds numbers for aeroelastically-scaled launch vehicle models has only recently been accomplished. The NASA Langley Transonic Dynamics Tunnel is capable of simulating flight-representative Reynolds numbers of launch vehicles on the pad and is uniquely capable of replicating many fluid-structure scaling parameters typical of aeroelastic tests. Recent test efforts successfully developed representative atmospheric boundary-layers for three launch sites in the Transonic Dynamics Tunnel, thereby allowing all known aerodynamic and fluid-structure coupling parameters to be simultaneously simulated for those sites. Dynamic aeroelastically-scaled models representative of typical large launch vehicles were constructed for testing. Aeroelastic scaling includes matching geometry, mode shapes, reduced frequencies, damping, running mass ratios, and running stiffness ratios. The models were tested in smooth uniform flow and then immersed in the atmospheric boundary-layer for comparison of these effects. Dynamic data were acquired measuring unsteady pressure, acceleration, and base bending moment. It was discovered that peak dynamic loads resulting from resonant wind-induced oscillation response are similar when acquired in either smooth uniform flow or an atmospheric boundary-layer. This indicates that resonant lock-in events are minimally impacted by representative turbulence and/or wind profile. Alternately, nonresonant wind-induced oscillation response events are stronger when acquired in an atmospheric boundary-layer. This indicates that a lowly-damped structural response will increase when exposed to an increased magnitude of random excitation, which is consistent with historical comparisons. Loads created by the resonant response events were substantially stronger than those from the nonresonant response events. Therefore, if testing is done to simply identify worst-case conditions and load magnitude, then smooth uniform flow is likely an adequate test technique. However, if nonresonant response loads are of primary interest, then atmospheric boundary-layer simulation is required.

Thomas G Ivanco↗