Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “flaps”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,603 records · Page 89
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Status of NASA advanced LFC airfoil high-lift study

The design of a high lift system for the NASA advanced LFC airfoil designed by Pfenninger is described. The high lift system consists of both leading and trailing edge flaps. A 3 meter semispan, 1 meter chord wing model using the above airfoil and high lift system is under construction and will be tested in the NASA Langley 4 by 7 meter tunnel. This model will have two separate full span leading edge flaps (0.10c and 0.12c) and one full span trailing edge flap (0.25c). The performance of this high lift system was predicted by the NASA two dimensional viscous multicomponent airfoil program. This program was also used to predict the characteristics of the LFC airfoils developed by the Douglas Aircraft Company and Lockheed-Georgia Aircraft Company.

Applin, Z. T.↗
NASA NTRS1982

Variable camber rotor study

Deployment of variable camber concepts on helicopter rotors was analytically assessed. It was determined that variable camber extended the operating range of helicopters provided that the correct compromise can be obtained between performance/loads gains and mechanical complexity. A number of variable camber concepts were reviewed on a two dimensional basis to determine the usefulness of leading edge, trailing edge and overall camber variation schemes. The most powerful method to vary camber was through the trailing edge flaps undergoing relatively small motions (-5 deg to +15 deg). The aerodynamic characteristics of the NASA/Ames A-1 airfoil with 35% and 50% plain trailing edge flaps were determined by means of current subcritical and transonic airfoil design methods and used by rotor performance and loads analysis codes. The most promising variable camber schedule reviewed was a configuration with a 35% plain flap deployment in an on/off mode near the tip of a blade. Preliminary results show approximately 11% reduction in power is possible at 192 knots and a rotor thrust coefficient of 0.09. The potential demonstrated indicates a significant potential for expanding the operating envelope of the helicopter. Further investigation into improving the power saving and defining the improvement in the operational envelope of the helicopter is recommended.

Dadone, L.↗
NASA NTRS1983

Results of free yaw tests of the Mod-O 100 kilowatt wind turbine

Tests were conducted on the Mod-O 100 kW experimental wind turbine to provide data on yaw alignment characteristics of a large horizontal axis wind turbine with its yaw restraint removed (i.e., in free yaw). The wind turbine consisted of a downwind horizontal axis rotor mounted on a tubular tower. Three rotor configurations were tested. Each rotor was teetered, coned 3 deg and tip-controlled. Two of the rotors had pitch-flap coupling or Delta-3, and one rotor had none. The two rotors with Delta-3 differed in the airfoil used in the tip sections. Test results indicate the rotor without pitch-flap coupling did not align closer than 25 deg with the wind, and pitch-flap coupling improved the wind turbine's alignment with the wind. Yaw damping was shown to have a favorable effect on free yaw characteristics. The change in the tip airfoil section was shown to affect the free yaw alignment also. The rotors with Delta-3 were shown to be capable of responding to wind shifts and exhibited stable operating properties.

Glasgow, J. C.↗
NASA NTRS1983

An experimental investigation of control surface effectiveness and real-gas simulation for biconics

Aerodynamic coefficients, pressure distributions, and oil-flow patterns measured on spherically blunted, 13 degrees/7 degrees on-axis and bent biconics at Mach 6 and 10 in air are compared. Angle of attack, referenced to the axis of the aft cone, was varied from zero to 40 degrees. The effect of deflection of base-mounted flaps on aerodynamic characteristics was examined at Mach 10. Real-gas effects on aerodynamic coefficients, pressure distributions and shock detachment distance were simulated by testing the biconic models in Mach 6 air and Mach 6 CF4 flows. (Density ratio equal to 5.3 for air and 12 for CF4.) The on-axis biconic is stable but cannot be trimmed at angles of attack above zero with the assumed center of gravity and flap configuration. Flaps on the bent biconic produced a stable and trim configuration for angles of attack from zero to 23 degrees. A significant effect of density ratio on aerodynamic coefficients, pressure distribution, and shock detachment distance was observed.

Miller, C. G.↗
NASA NTRS1983

An experimental heat-transfer investigation of an advanced winged entry vehicle at Mach 10

Heat-transfer measurements have been made at Mach 10 in air on an instrumented 0.006-scale model of an advanced winged entry vehicle. Data were obtained at 83 thermocouple stations which include locations on the lower and upper surface centerlines, spanwise positions along the lower and upper surfaces of the wing, the lower surface of the body flap, and radial locations on the fuselage. Data were obtained for angles of attack ranging from 0 to 45 deg, sideslip angles of + or - 2 deg, Reynolds numbers of 0.5, 1.0 and 2.0 million per foot, and body-flap deflections of 0, 10, and 20 deg. The data generally indicate increased windward heating and decreased leeside heating with increased angle of attack, significantly increased body-flap heating with deflection angle, and minor variations in heating with sideslip, increasing in magnitude with angle of attack. Windward centerline data are shown to be in fair agreement with results of predictions based on an approximate engineering method.

Wurster, K. E.↗
NASA NTRS1983

A static investigation of yaw vectoring concepts on two-dimensional convergent-divergent nozzles

The flow-turning capability and nozzle internal performance of yaw-vectoring nozzle geometries were tested in the NASA Langley 16-ft Transonic wind tunnel. The concept was investigated as a means of enhancing fighter jet performance. Five two-dimensional convergent-divergent nozzles were equipped for yaw-vectoring and examined. The configurations included a translating left sidewall, left and right sidewall flaps downstream of the nozzle throat, left sidewall flaps or port located upstream of the nozzle throat, and a powered rudder. Trials were also run with 20 deg of pitch thrust vectoring added. The feasibility of providing yaw-thrust vectoring was demonstrated, with the largest yaw vector angles being obtained with sidewall flaps downstream of the nozzle primary throat. It was concluded that yaw vector designs that scoop or capture internal nozzle flow provide the largest yaw-vector capability, but decrease the thrust the most.

Berrier, B. L.↗
NASA NTRS1983

Unsteady behavior of a reattaching shear layer

A detailed investigation of the unsteadiness in a reattaching, turbulent shear layer is reported. Laser-Doppler velocimeter measurements were conditionally sampled on the basis of instantaneous flow direction near reattachment. Conditions of abnormally short reattachment and abnormally long reattachment were considered. Ensemble-averaging of measurements made during these conditions was used to obtain mean velocities and Rreynolds stresses. In the mean flow, conditional streamlines show a global change in flow pattern which correlates with wall-flow direction. This motion can loosely be described as a 'flapping' of the shear layer. Tuft probes show that the flow direction reversals occur quite randomly and are shortlived. Streses shown also vary with the change in flow pattern. Yet, the global'flapping' motion does not appear to contribute significantly to the stress in the flow. A second type of unsteady motion was identified. Spectral analysis of both wall static pressure and streamwise velocity shows that most of the energy in the flow resides in frequencies that are significantly lower than that of the turbulence. The dominant frequency is at a Strouhal number equal to 0.2, which is the characteristic frequency of roll-up and pairing of vortical structure seen in free shear layers. It is conjectured that the 'flapping' is a disorder of the roll-up and pairing process occurring in the shear layer.

Driver, D. M.↗
NASA NTRS1983

Vortical flow management for improved configuration aerodynamics: Recent experiences

Recent progress in vortex-control applications for alleviating the adverse consequences of three dimensional separation and vortical interactions on slender body/swept wing configurations is reported. Examples include helical separation trip to alleviate the side force due to forebody vortex asymmetry; hinged strakes to avoid vortex breakdown effects; compartmentation of swept leading edge separation to delay the pitch-up instability; under wing vortex trip and vortex trip and vortex flaps for drag reduction at high lift; and an apex-flap trimmer to fully utilize the lift capability of trailing-edge flaps for take off and landing of delta wings. Experimental results on generic wind-tunnel models are presented to illustrate the vortex-management concepts involved and to indicate their potential for enhancing the subsonic aerodynamics of supersonic-cruise type vehicles.

Rao, D. M.↗
NASA NTRS1982

National Aerospace Laboratory News (Japan)

Tests carried out in November 1981 on the stationary flap of STOL test planes at Kakuda Labs are described. Acoustic pressure, outer plate temperature of the fore flap, and acceleration, strain, and temperature of the outer plate of the main flap were measured. High load turbine inlet distortion experiments were also performed. Results of these experiments are discussed.

Takeda, J.↗
NASA NTRS1984

Numerical analysis of a variable camber rotor blade as a lift control device

A new rotor configuration called the variable camber rotor was numerically investigated as a lift control device. This rotor differs from a conventional (baseline) rotor only in the blade aft section. In this configuration, the aft section or flap is attached to the forward section by pin joint arrangement, and also connected to the rotor control system for the control of rotor thrust level and vectoring. Pilot action to the flap deflection controls rotor lift and tip path plane tilt. The drag due to flaps is presented and the theoretical result correlated with test data. The assessment of payoff for the variable camber rotor in comparison with conventional (baseline) rotor was examined in hover. The variable camber rotor is shown to increase hover power required by 1.35%, but such a minimal power penalty is not significant enough to be considered a negative result. In forward flight, the control needs of the variable camber rotor were evaluated.

Awani, A. O.↗
NASA NTRS1983

V/STOL model fan stage rig design report

A model single-stage fan with variable inlet guide vanes (VIGV) was designed to demonstrate efficient point operation while providing flow and pressure ratio modulation capability required for a V/STOL propulsion system. The fan stage incorporates a split-flap VIGV with an independently actuated ID flap to permit independent modulation of fan and core engine airstreams, a flow splitter integrally designed into the blade and vanes to completely segregate fan and core airstreams in order to maximize core stream supercharging for V/STOL operation, and an EGV with a variable leading edge fan flap for rig performance optimization. The stage was designed for a maximum flow size of 37.4 kg/s (82.3 lb/s) for compatibility with LeRC test facility requirements. Design values at maximum flow for blade tip velocity and stage pressure ratio are 472 m/s (1550 ft/s) and 1.68, respectively.

Cheatham, J. G.↗
NASA NTRS1982

Pressure distribution data from tests of 2.29-meter (7.5-ft.) span EET high-lift research model in Langley 4- by 7-meter tunnel

A 2.29 m (7.5 ft.) span high-lift research model equipped with full-span leading-edge slat and part-span double-slotted trailing-edge flap was tested in the Langley 4- by 7-Meter Tunnel to determine the low speed performance characteristics of a representative high aspect ratio suprcritical wing. These tests were performed in support of the Energy Efficient Transport (EET) program which is one element of the Aircraft Energy Efficiency (ACEE) project. Static longitudinal forces and moments and chordwise pressure distributions at three spanwise stations were measured for cruise, climb, two take-off flap, and two landing flap wing configurations. The tabulated and plotted pressure distribution data is presented without analysis or discussion.

Morgan, H. L., Jr.↗
NASA NTRS1984

An experimental investigation of surface pressure measurements on an advanced winged entry vehicle at Mach 10

Surface pressure measurements have been made at Mach 10 in air on an instrumented 0.006-scale model of an advanced (control configured) winged entry vehicle. The tests were conducted in the Langley Continuous Flow Hypersonic Tunnel. Data were obtained at 83 surface pressure stations, which include locations on the lower and upper surface centerlines, spanwise positions along the lower and upper surfaces of the wing, the lower surface of the body flap, and radial locations on the fuselage. Data were obtained for angles of attack ranging from zero to 40 deg, sideslip angles of -2 deg to +5 deg, Reynolds numbers of 0.5, 1.0, and 2.0 million per foot, and body-flap deflections of zero, 10, and 20 deg. Test conditions and orifice locations were chosen to correspond directly with those for the heat transfer measurements previously reported on the same configuration. Comparison of windward symmetry plane data with predictions based upon an approximate engineering method was found to yield reasonable agreement for angles of attack from 20 to 40 deg. The leeward surface pressure data were observed to be roughly an order of magnitude lower than the corresponding windward data. At low angles of attack, regions of high pressure were noted on the windward wing surface. The result is attributed to vortical action or shock impingement. High pressures were also measured on the deflected body flap, a critical region for this type of vehicle. Reynolds number effects were found to be insignificant.

Wurster, K. E.↗
NASA NTRS1985

Static internal performance of a two-dimensional convergent nozzle with thrust-vectoring capability up to 60 deg

An investigation was conducted at wind-off conditions in the static-test facility of the Langley 16-Foot Transonic Tunnel to determine the internal performance characteristics of a two-dimensional convergent nozzle with a thrust-vectoring capability up to 60 deg. Vectoring was accomplished by a downward rotation of a hinged upper convergent flap and a corresponding rotation of a center-pivoted lower convergent flap. The effects of geometric thrust-vector angle and upper-rotating-flap geometry on internal nozzle performance characteristics were investigated. Nozzle pressure ratio was varied from 1.0 (jet off) to approximately 5.0.

Leavitt, L. D.↗
NASA NTRS1985

Bifurcation theory applied to aircraft motions

Bifurcation theory is used to analyze the nonlinear dynamic stability characteristics of single-degree-of-freedom motions of an aircraft or a flap about a trim position. The bifurcation theory analysis reveals that when the bifurcation parameter, e.g., the angle of attack, is increased beyond a critical value at which the aerodynamic damping vanishes, a new solution representing finite-amplitude periodic motion bifurcates from the previously stable steady motion. The sign of a simple criterion, cast in terms of aerodynamic properties, determines whether the bifurcating solution is stable (supercritical) or unstable (subcritical). For the pitching motion of a flap-plate airfoil flying at supersonic/hypersonic speed, and for oscillation of a flap at transonic speed, the bifurcation is subcritical, implying either that exchanges of stability between steady and periodic motion are accompanied by hysteresis phenomena, or that potentially large aperiodic departures from steady motion may develop. On the other hand, for the rolling oscillation of a slender delta wing in subsonic flight (wing rock), the bifurcation is found to be supercritical. This and the predicted amplitude of the bifurcation periodic motion are in good agreement with experiments.

Hui, W. H.↗
NASA NTRS1985

Static investigation of several yaw vectoring concepts on nonaxisymmetric nozzles

A test has been conducted in the static test facility of the Langley 16-Foot Transonic Tunnel to determine the flow-turning capability and the effects on nozzle internal performance of several yaw vectoring concepts. Nonaxisymmetric convergent-divergent nozzles with throat areas simulating dry and afterburning power settings and single expansion ramp nozzles with a throat area simulating a dry power setting were modified for yaw thrust vectoring. Forward-thrust and pitch-vectored nozzle configurations were tested with each yaw vectoring concept. Four basic yaw vectoring concepts were investigated on the nonaxisymmetric convergent-divergent nozzles: (1) translating sidewall; (2) downstream (of throat) flaps; (3) upstream (of throat) port/flap; and (4) powered rudder. Selected combinations of the rudder with downstream flaps or upstream port/flap were also tested. A single yaw vectoring concept, post-exit flaps, was investigated on the single expansion ramp nozzles. All testing was conducted at static (no external flow) conditions and nozzle pressure ratios varied from 2.0 up to 10.0.

Mason, M. L.↗
NASA NTRS1983

Pressure distribution data from tests of 2.29 M (7.5 feet) span EET high-lift transport aircraft model in the Ames 12-foot pressure tunnel

A high-lift transport aircraft model equipped with full-span leading-edge slat and part-span double-slotted trailing-edge flap was tested in the Ames 12-ft pressure tunnel to determine the low-speed performance characteristics of a representative high-aspect-ratio supercritical wing. These tests were performed in support of the Energy Efficient Transport (EET) program which is one element of the Aircraft Energy Efficiency (ACEE) project. Static longitudinal forces and moments and chordwise pressure distributions at three spanwise stations were measured for cruise, climb, two take-off flap, and two landing flap wing configurations. The tabulated and plotted pressure distribution data is presented without analysis or discussion.

Kjelgaard, S. O.↗
NASA NTRS1985

Subsonic pressure distributions near a wing-fin juncture on a supersonic arrow-wing configuration with wing-mounted vertical fins

A generic supersonic arrow-wing configuration has been extensively studied to develop a consistent experimental data base to aid in verifying analytical prediction methods. One of the wing configurations studied was a twisted and cambered wing with wing-mounted vertical fins and trailing-edge flaps. The pressure data obtained on that configuration was limited in the wing-fin juncture region, and no pressures were obtained on the fin itself. However, detailed data in the juncture region and on the fin are essential to check out the analytical prediction methods. Therefore, the model was modified to provide details of the juncture pressure field as well as pressures on the fin. The results of this experimental investigation showed that the addition of a fin helped improve the wing pressure distribution outboard of the fin. Deflection of the trailing-edge flap did not adversely affect this trend. The pressure distributions on the vertical fin were generally affected more by change in angle of attack than by flap deflection. The spanwise pressure distribution on the fin itself indicated a load reversal with angle of attack.

Huffman, J. K.↗