SEARCH · Engineering Papers

Results for “boundary layer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,603 records · Page 89

All sources NASA NTRS DOE OSTI

NASA NTRS2002

A Ground-Based Profiling Differential Absorption LIDAR System for Measuring CO2 in the Planetary Boundary Layer

Ground-based LIDAR observations can potentially provide continuous profiles of CO2 through the planetary boundary layer and into the free troposphere. We will present initial atmospheric measurements from a prototype system that is based on components developed by the telecommunications industry. Preliminary measurements and instrument performance calculations indicate that an optimized differential absorption LIDAR (DIAL) system will be capable of providing continuous hourly averaged profiles with 250m vertical resolution and better than 1 ppm precision at 1 km. Precision increases (decreases) at lower (higher) altitudes and is directly proportional to altitude resolution and acquisition time. Thus, precision can be improved if temporal or vertical resolution is sacrificed. Our approach measures absorption by CO2 of pulsed laser light at 1.6 microns backscattered from atmospheric aerosols. Aerosol concentrations in the planetary boundary layer are relatively high and are expected to provide adequate signal returns for the desired resolution. The long-term goal of the project is to develop a rugged, autonomous system using only commercially available components that can be replicated inexpensively for deployment in a monitoring network.

Andrews, Arlyn E.↗

NASA NTRS1983

Annulus wall boundary layer development in a compressor stage, including the effects of tip clearance

The end-wall boundary layer development in a compressor stage, including the inlet guide vane (IGV) passage and the rotor passage, was measured. The measurement upstream of the rotor and inside the IGV passage were carried out with a five-hole probe. The data (blade-to-blade) inside the IGV passage were carried out with a five-hole probe. The data (blade-to-blade) inside the rotor passage were measured using a three-sensor rotating hot-wire below the tip clearance region and "V' configuration probe inside the clearance region. The rotor exit measurements (blade-to-blade) were acquired with a laser Doppler velocimeter. The velocity profiles and the integral properties are presented and interpreted. The boundary layer is comparatively well behaved up to the leading edge of the rotor, beyond which complex interactions result in very unconventional profiles. The momentum thicknesses decrease in the leakage flow region of the rotor. The momentum thicknesses and the limiting streamline angles predicted from a momentum integral technique agree well with the data up to the leading edge of the rotor.

Lakshminarayana, B.↗

DOE OSTI2024

Tethered balloon-borne observations of thermal-infrared irradiance and cooling rate profiles in the Arctic atmospheric boundary layer

Clouds play an important role in controlling the radiative energy budget of the Arctic atmospheric boundary layer. To quantify the impact of clouds on the radiative heating or cooling of the lower atmosphere and of the surface, vertical profile observations of thermal-infrared irradiances were collected using a radiation measurement system carried by a tethered balloon. We present 70 profiles of thermal-infrared radiative quantities measured in summer 2020 during the Multidisciplinary drifting Observatory for the Study of Arctic Climate (MOSAiC) expedition and in autumn 2021 and spring 2022 in Ny-Ålesund, Svalbard. Measurements are classified into four groups: cloudless, low-level liquid-bearing cloud, elevated liquid-bearing cloud, and elevated ice cloud. Cloudless cases display an average radiative cooling rate of about —2 K d—1 throughout the atmospheric boundary layer. Instead, low-level liquid-bearing clouds are characterized by a radiative cooling up to —80 K d—1 within a shallow layer at cloud top, while no temperature tendencies are identified underneath the cloud layer. Radiative transfer simulations are performed to quantify the sensitivity of radiative cooling rates to cloud microphysical properties. In particular, cloud top cooling is strongly driven by the liquid water path, especially in optically thin clouds, while for optically thick clouds the cloud droplet number concentration has an increased influence. Additional radiative transfer simulations are used to demonstrate the enhanced radiative importance of the liquid relative to ice clouds. To analyze the temporal evolution of thermal-infrared radiation profiles during the transitions from a cloudy to a cloudless atmosphere, a respective case study is investigated.

54 ENVIRONMENTAL SCIENCES↗

NASA NTRS1984

On the instability of a 3-dimensional attachment line boundary layer: Weakly nonlinear theory and a numerical approach

The instability of a three dimensional attachment line boundary layer is considered in the nonlinear regime. Using weakly nonlinear theory, it is found that, apart from a small interval near the (linear) critical Reynolds number, finite amplitude solutions bifurcate subcritically from the upper branch of the neutral curve. The time dependent Navier-Stokes equations for the attachment line flow have been solved using a Fourier-Chebyshev spectral method and the subcritical instability is found at wavenumbers that correspond to the upper branch. Both the theory and the numerical calculations show the existence of supercritical finite amplitude (equilibrium) states near the lower branch which explains why the observed flow exhibits a preference for the lower branch modes. The effect of blowing and suction on nonlinear stability of the attachment line boundary layer is also investigated.

Hall, P.↗

NASA NTRS2019

Comparison of Boundary Layer Similarity Transformations for High Mach Number Flows

Reynolds averaged Navier-Stokes (RANS) simulations of the turbulent boundary layer flow on a flat plate are performed across a Mach number range of 0.3 up to 16 using the computational fluid dynamics (CFD) software, VULCAN-CFD. The simulation results are used to evaluate the ability of the Van Driest transformation and the transformation of Trettel and Larsson to collapse boundary layer velocity profiles under various flow conditions across the range of Mach numbers. The flat platewall boundary conditions and leading edge geometry are varied from adiabatic to isothermal and sharp to blunted to reveal the physics of how these effects impact the performance of the chosen flow transformations. Results indicate that the transformation of Trettel and Larsson produces a better collapse of velocity profile data than the Van Driest transformation regardless of Mach number, wall boundary condition, or leading edge geometry. In addition, the velocity gradients obtained from the transformation of Trettel and Larsson match the normalized untransformed velocity gradients much more closely than those obtained using the Van Driest transformation.

DiGregorio, Nicholas J.↗

NASA NTRS1987

Reynolds shear stress development in pressure-driven three-dimensional turbulent boundary-layers

The development of the Reynolds stresses has been examined experimentally in an initially two-dimensional boundary layer which is driven to three dimensionality by a spanwise pressure gradient. The pressure field was imposed by an upstream-facing wedge. Two different wedge angles were used in order to vary the level of boundary layer skewing. Bradshaw's Al parameter was found to decrease with the rate of decrease being dependent on the level of skewing between the freestream and the wall flow. It was also concluded that the ratio of the cross-stream to streamwise shear stress components was governed by the rate of freestream turning.

Anderson, S. D.↗

NASA NTRS1954

Performance and boundary-layer data from 12 degree and 23 degree conical diffusers of area ratio 2.0 at Mach numbers up to choking and Reynolds numbers up to 7.5 x 10(6)

For each of two inlet-boundary-layer thicknesses, performance and boundary-layer characteristics have been determined for a 12 degree, 10-inch-inlet-diameter diffuser, a 12 degree, 21-inch-inlet-diameter diffuser, and a 23 degree, 21-inch-inlet-diameter diffuser. The investigation covered an inlet Mach number range from about 0.10 to coking. The corresponding inlet Reynolds number, based on inlet diameter, varied from about 0.5 x 10(6) to 7.5 x 10(6).

Little, B H , Jr↗

NASA NTRS1977

Experimental and theoretical investigation of three-dimensional turbulent boundary layers and turbulence characteristics inside an axial flow inducer passage

Analytical and experimental investigations of the characteristics of three dimensional turbulent boundary layers in a rotating helical passage of an inducer rotor are reported. Expressions are developed for the velocity profiles in the inner layer, where the viscous effects dominate, in the outer layer, where the viscous effects are small, and in the interference layer, where the end walls influence the flow. The prediction of boundary layer growth is based on the momentum integral technique. The equations derived are general enough to be valid for all turbomachinery rotors with arbitrary pressure gradients. The experimental investigations are carried out in a flat plate inducer 3 feet in diameter. The mean velocity profiles, turbulence intensities and shear stresses, wall shear stress, and limiting streamline angles are measured at various radial and chordwise locations by using rotating probes. The measurements are in general agreement with the predictions. The radial flows are well represented by an expression which includes the effect of stagger angle and radial pressure gradient. The radial flows in the rotor channel are higher than those on a single blade. The collateral region exists only very near the blade surface. The radial component of turbulence intensity is higher than the streamwise component because of the effect of rotation.

Anand, A. K.↗

NASA NTRS1981

Simple approximations for the asymptotic description of the interaction between a normal shock wave and a turbulent boundary layer at transonic speeds

The asymptotic description of the interaction between a normal shock wave and a turbulent boundary layer is reviewed. The layers necessary in a rational analysis of the interaction are discussed with emphasis on the differences from an interaction with a laminar boundary layer, the uncoupling of solutions for the distribution of pressure and skin friction at the wall, and the role of the Reynolds shear stress in these solutions. The accuracy of asymptotic solutions in flows at Reynolds numbers of technical interest is discussed. Solutions for the distribution of pressure and skin friction at the wall and the shape of the shock are considered for the case where the flow is near separation. For the pressure and skin friction, it is possible to write two simplified partial solutions, one valid at the beginning of the interaction and one valid somewhat downstream of the shock wave. A solution composed of these two parts and a linear interpolation between them appears to give good comparison with experiment; one unknown constant, independent of the parameters of the interaction, must be found from experiment. The simplified relations are presented. Comparison of numerical computations with experimental data indicates a possible value for the constant and shows quite satisfactory results.

Adamson, T. C., Jr.↗

NASA NTRS2004

Effect of Blowing on Boundary Layer of Scarf Inlet

When aircraft operate in stationary or low speed conditions, airflow into the engine accelerates around the inlet lip and pockets of turbulence that cause noise and vibration can be ingested. This problem has been encountered with engines equipped with the scarf inlet, both in full scale and in model tests, where the noise produced during the static test makes it difficult to assess the noise reduction performance of the scarf inlet. NASA Langley researchers have implemented boundary layer control in an attempt to reduce the influence of the flow nonuniformity in a 12-in. diameter model of a high bypass fan engine mounted in an anechoic chamber. Static pressures and boundary layer profiles were measured in the inlet and far field acoustic measurements were made to assess the effectiveness of the blowing treatment. The blowing system was found to lack the authority to overcome the inlet distortions. Methods to improve the implementation of boundary layer control to reduce inlet distortion are discussed.

Gerhold, Carl H.↗

NASA NTRS1996

Effects of Nonequilibrium at Edge of Boundary Layer on Convective Heat Transfer to a Blunt Body

This investigation is a continuation of a previous study on nonequilibrium convective heat transfer to a blunt body. In the previous study, for relatively high Reynolds number flows, it was found that: nonequilibrium convective heat transfer to a blunt body is not strongly dependent on freestream parameters, provided that the thermochemical equilibrium is reached at the edge of boundary layer; and successful testing of convective heat transfer in an arc-jet environment is possible by duplicating the surface pressure and total enthalpy. The nonequilibrium convective heat transfer computations are validated against the results of Fay and Riddell/Goulard theory. Present work investigates low Reynolds number conditions which are typical in an actual arc-jet flow environment. One expects that there will be departures from the Fay and Riddell/Goulard result since certain assumptions of the classical theory are not satisfied. These departures are of interest because the Fay and Riddell/Goulard formulas are extensively used in arc-jet testing (e.g., to determine the enthalpy of the flow and the catalytic efficiency of heat shield materials). For practical sizes of test materials, density of the test flow (and Reynolds number) in an arc-jet is such that thermochemical equilibrium may not be reached at the edge of boundary layer. For blunt body flows of nitrogen and air, computations will be presented to show the effects of thermochemical nonequilibrium at the boundary layer edge on nonequilibrium heat transfer.

Goekcen, Tahir↗

NASA NTRS1994

ROSAT observations of cataclysmic variables: A search for the boundary layer emission

Many cataclysmic variables (CVs) and low-mass X-ray binaries show He II line emission at wavelength 1640 and wavelength 4686. As recombination lines of an ion requiring 55 eV for ionization, these lines cannot be attributed to gravitational heating in the disk but could be due to reprocessed 55-280 eV X-rays which may be produced in a boundary layer at the disk/star surface. We undertook a search for this soft component using the Positon Sensitve Proportional Counter (PSPC) on ROSAT. The photon fluxes we observe are not sufficient to produce the He II wavelength 1640 fluxes observed by IUE. If we assume that the X-ray luminosity is due to emission from a boundary layer, then the observed quiescent luminosity is one-quarter of the total accretion luminosity as determined by optical and ultraviolet observations rather than the one-half that is predicted by some theories. An additional very soft component (e.g. an approximately equal 10-20 eV blackbody) could provide sufficient photons in the 0.055-0.100 keV band to produce the observed He II fluxes and contribute the additional luminosity from the boundary layer while remaining hidden to the PSPC and IUE. Alternatively, the high He II line fluxes could be evidence for high-temperature collisionally ionized material. We also find evidence for line emission at approximately equal 0.9 keV consistent with L-shell emission from highly ionized iron.

Vrtilek, S. D.↗

DOE OSTI2021

Editors’ Choice—Natural Convection Boundary Layer Thickness at Elevated Chloride Concentrations and Temperatures and the Effects on a Galvanic Couple

The natural convection boundary layer ( δ n c ) and its influence on cathodic current in a galvanic couple under varying electrolytes as a function of concentration (1 − 5.3 M NaCl) and temperature (25 °C−45 °C) were understood. Polarization scans were obtained under quiescent conditions and at defined boundary layer thicknesses using a rotating disk electrode on platinum and stainless steel 304L (SS304L); these were combined to determine δ n c . With increasing chloride concentration and temperature, δ n c decreased. Increased mass transport (Sherwood number) results in a decrease in δ n c , providing a means to predict this important boundary. Using Finite Element Modeling, the cathodic current was calculated for an aluminum alloy/SS304L galvanic couple as a function of water layer ( WL ) thickness and cathode length. Electrolyte domains were delineated, describing (i) dominance of ohmic resistance over mass transport under thin WL , (ii) the transition from thin film to bulk conditions at δ n c , and (iii) dominance of mass transport under thick WL . With increasing chloride concentration, cathodic current decreased due to decreases in mass transport. With increasing temperature, increased cathodic current was related to increases in mass transport and solution conductivity. This study has implications for sample sizing and corrosion prediction under changing environments.

25 ENERGY STORAGE↗

NASA NTRS1956

On the period of the coherent structure in boundary layers at large Reynolds numbers

The period of the large coherent structure in a subsonic, compressible, turbulent boundary layer was determined using the autocorrelation of the velocity and pressure fluctuations for Reynolds numbers between 5,000 and 35,000. In low Reynolds number flows the overall correlation period scaled with the outer variables - namely, the free stream velocity and the boundary layer thickness.

Narayanan, M. A. B.↗

NASA NTRS1994

Linking boundary-layer circulations and surface processes during FIFE89. Part 1: Observational analysis

Surface, aircraft, and satellite observations are analyzed for the 21-day 1989 intensive field campaign of the First ISLSCP Field Experiment (FIFE) to determine the effect of precipitation, vegetation, and soil moisture distributions on the thermal properties of the surface including the heat and moisture fluxes, and the corresponding response in the boundary-layer circulation. Mean and variance properties of the surface variables are first documented at various time and space scales. These calculations are designed to set the stage for Part 2, a modeling study that will focus on how time-space dependent rainfall distribution influences the intensity of the feedback between a vegetated surface and the atmospheric boundary layer. Further analysis shows strongly demarked vegetation and soil moisture gradients extending across the FIFE experimental site that were developed and maintained by the antecedent and ongoing spatial distribution of rainfall over the region. These gradients are shown to have a pronounced influence on the thermodynamic properties of the surface. Furthermore, perturbation surface wind analysis suggests for both short-term steady-state conditions and long-term averaged conditions that the gradient pattern maintained a diurnally oscillating local direct circulation with perturbation vertical velocities of the same order as developing cumulus clouds. Dynamical and scaling considerations suggest that the embedded perturbation circulation is driven by surface heating/cooling gradients and terrain ef fects rather than the manifestation of an inertial oscillation. The implication is that at even relatively small scales (less than 30 km), the differential evolution in vegetation density and soil moisture distribution over a relatively homogenous ecotone can give rise to preferential boundary-layer circulations capable of modifying local-scale horizontal and vertical motions.

Smith, Eric A.↗

DOE OSTI2026

Improving Process Level Understanding of Boundary Layer Winds over the Northeast U.S. Shelf: The Third Wind Forecast Improvement Project (WFIP3)

The third Wind Forecast Improvement Project (WFIP3), a U.S. Department of Energy and National Oceanic and Atmospheric Administration sponsored investigation, sought to improve understanding of the physical phenomena in the atmosphere and ocean that dictate the structure and variability of wind and thermodynamic fields within the marine atmospheric boundary layer. WFIP3 focused on mesoscale and submesoscale flows -- including sea breezes, low-level jets, low-level clouds, and coastal storms -- and the ability of advanced numerical model parameterizations to represent them within fully coupled oceanic and atmospheric modeling systems and foundational weather forecast models. WFIP3 conducted a comprehensive 18-month observational study over the Northeast U.S. outer continental shelf, a high-use coastal zone, using a 3D multiscale sensor array to highly resolve the temporal, vertical, and horizontal structure of the coupled atmospheric and oceanic boundary layers. Multiple land-based study sites adjacent to the coastal ocean observed surface meteorology and vertical profiles of atmospheric properties via passive infrared and microwave radiometers, active lidars and radars, and radiosondes. At sea, an array of surface flux buoys and two vertical profiling lidar buoys observed both atmospheric and oceanic properties, augmented by land-based oceanographic radar systems and routine ship-based surveys. Intensive observations of the marine atmospheric boundary layer over the ocean was done from an air-sea interaction flux tower and extended deployments of a large autonomous barge platform. Numerous critical forecasting phenomena were observed that are being evaluated within regional coupled and uncoupled modeling systems, including the National Oceanic and Atmospheric Administration's foundational High-Resolution Rapid Refresh forecast model.

Kirincich, Anthony↗

NASA NTRS1955

Analysis and calculation by integral methods of laminar compressible boundary-layer with heat transfer and with and without pressure gradient

A survey of integral methods in laminar-boundary-layer analysis is first given. A simple and sufficiently accurate method for practical purposes of calculating the properties (including stability) of the laminar compressible boundary layer in an axial pressure gradient with heat transfer at the wall is presented. For flow over a flat plate, the method is applicable for an arbitrarily prescribed distribution of temperature along the surface and for any given constant Prandtl number close to unity. For flow in a pressure gradient, the method is based on a Prandtl number of unity and a uniform wall temperature. A simple and accurate method of determining the separation point in a compressible flow with an adverse pressure gradient over a surface at a given uniform wall temperature is developed. The analysis is based on an extension of the Karman-Pohlhausen method to the momentum and the thermal energy equations in conjunction with fourth- and especially higher degree velocity and stagnation-enthalpy profiles.

Morduchow, Morris↗