Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Texture”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,603 records · Page 89

Development of rare-earth-free bulk magnets with energy product up to 12 MGOe in field annealed Mn–Bi–Mg–In–Sb alloys

A treatment consisting of annealing in a moderately strong, ≤30 kOe, magnetic field was applied to arc-melted ingots and compacted melt-spun alloys with composition Mn 50 Bi 50-x-y-z Mg x In y Sb z . The high degree of texture of the magnetic α phase induced with annealing of the ingot samples (except the Mn–Bi–Sb one) allowed for accurate determination of the phase anisotropy field. Alloying was found to increase the anisotropy field from 45 kOe in the Mn 50 Bi 50 alloy to 65 kOe in the Mn 50 Bi 45 Mg 3 In 0.5 Sb 1.5 alloy. In the compacted melt-spun alloys subjected to field annealing, a higher degree of texture could be achieved after compaction which had involved less heating, when a smaller fraction of the metastable β' phase had been converted into the α phase; compaction at room temperature allowed for the highest degree of texture in the Mn 50 Bi 45 Mg 3 In 0.5 Sb 1.5 magnet. The addition of indium was found to decrease the solidus temperatures of the alloys, facilitating the development of the α phase during the field annealing and modifying the properties of the resulting magnets. Introduction of indium resulted in a higher coercivity H c of the Mn–Bi–Mg–In magnets and in a better texture of the Mn–Bi–Mg–Sn–In magnets. The former effect allowed, in particular, for a viable maximum energy product ( BH ) max of 10 MGOe to be developed in the Mn 50 Bi 46.5 Mg 3 In 0.5 magnet through annealing in a relatively low field of 15 kOe, whereas the latter effect allowed for an excellent combination of ( BH ) max = 11.6 MGOe and H c = 8.5 kOe in the Mn 50 Bi 45 Mg 3 In 0.5 Sb 1.5 magnet. The highest ( BH ) max of 12 MGOe was realized in the Mn 50 Bi 46 Mg 3 In 0.5 Sb 0.5 magnet.

36 MATERIALS SCIENCE↗

Thin La{sub 2}Zr{sub 2}O{sub 7} films made from a water-based solution

Thin films of La{sub 2}Zr{sub 2}O{sub 7} (LZO) are highly regarded as possible buffer layers in the coated conductor configuration. This report describes a new synthesis for thin crystalline LZO films, based on a largely water-based solution, mainly containing metal acetates, acetic acid and an organic amine-base: triethanolamine. Initially, a thin layer of amorphous material is deposited on the textured Ni-5 at%W substrate by means of dip-coating. Only by careful control of the thermal treatment can the layer be transformed into a crystalline layer. Important parameters in this respect are the heating rate and the dwell time. The amorphous gel is analysed by HR-TGA/DTA and HR-TEM. The textured layers are analysed by XRD, pole figures, RHEED, AFM and SEM. - Grapical Abstract: Thin films of La2Zr2O7 (LZO) are produced via a water-based solution, containing metal acetates, acetic acid and triethanolamine. The thin layer is deposited on the textured Ni-5 at%W substrate by dip-coating. The amorphous gel is analysed by HR-TGA/DTA and HR-TEM. The textured layers are analysed by XRD, pole figures, RHEED analysis, AFM and SEM.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Electron backscattering diffraction analysis of an ancient wootz steel blade from central India

The electron backscattering diffraction technique was used to analyse the nature of carbides present in an ancient wootz steel blade. Bulky carbides, pro-eutectoid carbide along the prior austenite grain boundaries and fine spheroidized carbides were detected. Electron backscattering diffraction was employed to understand the texture of these carbides. The orientations of the cementite frequently occur in clusters, which points to a common origin of the members of the cluster. For the bands of coarse cementite, the origin is probably large coarse particles formed during the original cooling of the wootz cake. Pearlite formed earlier in the forging process has led to groups of similarly oriented fine cementite particles. The crystallographic texture of the cementite is sharp whereas that of the ferrite is weak. The sharp cementite textures point to the longevity of the coarse cementite throughout the repeated forging steps and to the influence of existing textured cementite on the nucleation of new cementite during cooling.

36 MATERIALS SCIENCE↗

Relationship between laser energy input, microstructures and magnetic properties of selective laser melted Fe-6.9%wt Si soft magnets

Highlights: • Effect of laser energy input on magnetic properties of SLM Fe-6.9%wt.Si is described; • Magnetic properties can be described as function of as-built microstructure after stress-relief post-treatment; • Samples with density >99% and strong crystallographic texture along BD have the best magnetic properties; • At very high laser energy, a strong cube texture forms that deteriorates the magnetic properties. - Abstract: Selective Laser Melting (SLM), a powder-bed Additive Manufacturing technology, can be used in combination with high temperature post-annealing to produce high-silicon steel parts characterised by quasi-static magnetic properties comparable to those of commercial electrical steel. However, the role of the as-built microstructure on the magnetic properties is still unexplored. Therefore, in this study the effect of the energy input of the processing laser on the magnetic properties of the material is investigated. The magnetic properties are determined for 4 mm-high rings obtained using three laser energy input values that provide a good compromise in terms of porosity and crack formation. The best magnetic properties are obtained for the rings built using a value of energy input that produces a strong fibrous crystallographic texture, in which one of the crystallographic <001> axes is preferentially aligned along the build direction. Whether the magnetic properties change with sample direction as a result of the crystallographic texture will be the subject of future research.

36 MATERIALS SCIENCE↗

Simultaneously improving mechanical properties and corrosion resistance of pure Ti by continuous ECAP plus short-duration annealing

Highlights: • Additional short-time annealing led to enhanced strength of UFG Ti due to texture strengthening. • UFG Ti showed improved corrosion resistance in artificial seawater compared with initial CG Ti. • Short-duration annealing enhanced corrosion resistance of UFG Ti due to stronger basal texture. - Abstract: This work investigated the effect of short-duration annealing on mechanical properties and corrosion behavior of bulk ultrafine-grained (UFG) pure Ti (grade 2) produced by high-efficiency equal-channel angular pressing (ECAP), serving the fast developing of marine industries. The initial coarse-grained (CG) Ti achieved higher strength after continuous ECAP at 420 °C for 4 passes, while additional short-duration annealing at 300 °C for 15 min of UFG Ti further led to extraordinary improvement of strength, which was associated with texture strengthening. The yield strength was increased from 362 MPa in as-received state to 561 MPa in post-ECAP annealed condition, and ultimate tensile strength from 450 MPa to 663 MPa. The ECAP-processed UFG Ti had better corrosion resistance in artificial seawater than the initial CG Ti. Short-duration annealing further improved the corrosion resistance of UFG Ti, which was related to stronger basal texture. The corrosion current density decreased from 68.37 nA cm{sup −2} for CG Ti in as-received condition to 41.77 nA cm{sup −2} for UFG Ti processed by ECAP plus short-duration annealing. The fraction of TiO{sub 2} within the surface oxide film for the post-ECAP annealed sample was increased. The bulk UFG Ti after post-ECAP short-duration annealing revealed an excellent combination of high strength, good ductility and superior corrosion resistance for marine applications.

36 MATERIALS SCIENCE↗

In situ monitoring of dislocation, twinning, and detwinning modes in an extruded magnesium alloy under cyclic loading conditions

This work investigates the microscopic deformation mechanisms of an extruded, precipitation-strengthened AZ80 magnesium (Mg) alloy subjected to strain-controlled low-cycle fatigue using in situ neutron diffraction measurements. Results demonstrate that the plastic deformation during cyclic loading is dominated by the alternating {10.2} extension twinning and detwinning mechanisms. The observed deformation mode is strongly texture and precipitate dependent. For the initial texture, the tested material has two major texture components which result in the occurrence of extension twinning during both compression and reverse tension in the first two cycles. The prolonged detwinning process in the following cycles is proposed to relieve the shear stress field of {00.2} grains, leading to the disappearance of twinning. The precipitation strengthening results in an increase of the critical resolved shear stress (CRSS) by similar to 33 MPa for the extension twinning in this AZ80 alloy. Here, the synergistic effects of the initial texture, precipitation strengthening, and load sharing of various grain families and phases contribute to the complicated evolution of dominant deformation mechanisms, among which elevated dislocation activities are believed to be responsible for the relatively poor low-cycle-fatigue lifetime when compared to other Mg alloys.

36 MATERIALS SCIENCE↗

A meta-analysis of global cropland soil carbon changes due to cover cropping

Including cover crops within agricultural rotations may increase soil organic carbon (SOC). However, contradictory findings generated by on-site experiments make it necessary to perform a comprehensive assessment of interactions between cover crops, environmental and management factors, and changes in SOC. In this study, we collected data from studies that compared agricultural production with and without cover crops, and then analyzed those data using meta-analysis and regression. Our results showed that including cover crops into rotations significantly increased SOC, with an overall mean change of 15.5% (95% confidence interval of 13.8% to 17.3%). Whereas medium-textured soils had highest SOC stocks with (mean = 39 Mg ha-1) and without (mean = 37 Mg ha-1) cover crops, fine-textured soils showed the greatest increase in SOC after the inclusion of cover crops (mean change of 39.5%). Coarse-textured (11.4%) and medium-textured soils (10.3%) had comparatively smaller changes in SOC. Cover crop mixtures resulted in greater increases in SOC compared to mono-species cover crops, and using legumes resulted in greater SOC increases than grasses and broadleaf species. Cover cropping was associated with significant SOC increases in shallow soils (= 30 cm), but not in subsurface soils (> 30 cm). The regression analysis revealed that SOC changes from cover cropping were correlated with improvements in soil quality, specifically decreased runoff and erosion and increased mineralizable carbon, mineralizable nitrogen, and soil nitrogen. Soil carbon change was also affected by annual temperature, number of years after start of cover crop usage, latitude, and initial SOC concentrations. Finally, the mean rate of carbon sequestration from cover cropping across all studies was 0.56 Mg ha-1 yr-1. If 15% of current global cropland were to adopt cover crops, this value would translate to 0.17 Pg of carbon sequestered per year or ~1-2% of current fossil fuels emissions. Altogether, these results indicated that inclusion of cover crops into agricultural rotations can enhance soil carbon concentrations, improve many soil quality parameters, and serve as a potential sink for atmosphere CO2.

Cover crop, soil organic carbon, soil quality, soi↗

Lipids represent a dynamic, yet stable pool of microbially-derived soil carbon

There is an emerging consensus that microorganisms are a primary source of persistent, slow-cycling soil organic matter (SOM), however which microbial residues contribute to SOM and what controls their accumulation remains unresolved. Lipids are a commonly overlooked biomolecular pool that could contribute significantly to stable SOM. While current estimates for phospholipid degradation in soils are rapid, lipids are structurally heterogeneous molecules that could turnover at different rates. Through a year-long soil incubation and compound-specific, stable isotope probing (SIP)-lipidomics, we were able to rigorously track the persistence of lipid compounds in silty and sandy switchgrass bioenergy crop soils. Here, we assessed the influence of lipid structure on soil lipid accrual and degradation as moderated by soil texture, since mineral association is presumed to be the primary mechanism for lipid persistence. After rapid incorporation of 13 C glucose into microbial biomass, we found 13 C label was retained broadly across chemically diverse lipid classes, even after one year. 13 C-labeled lipid profiles varied significantly with soil texture; however, we found no difference between sandy and silty soils in lipid retention, suggesting soil texture may only play a minor role in modulating lipid persistence. Only two lipid subclasses were found to be persistent (i.e., retention of 13 C label without significant degradation or production): phosphatidylinositol lipids and hydroxyceramide lipids, both of which are negatively charged, possibly facilitating stabilization by mineral complexation. However, several other subclasses displayed substantial ongoing production. In particular, the accumulation of triacylglycerol lipids across soil textures suggests that storage lipids may be an important component of SOC, highlighting a potential target for management strategies to promote C retention by lipid accrual. Overall, the retention for over a year of 13 C label in microbial intact lipid biomarkers reveals the importance of efficient biomass production and turnover when considering microbial C contributions to SOM.

compound-specific↗

Emissivity of solar cell cover glass calculated from infrared reflectance measurements

The thermal emissivity of solar cell cover glasses with differences in glass composition or manufacture and surface texture are evaluated using specular and specular+diffuse infrared reflectance at different angles of incidences. Non-textured and textured glasses all exhibit similar emissivity at all angles of incidence regardless of composition and patterning. Both diffuse and specular reflectance must be included for textured glass at any angle of incidence and may be needed for planar glass at a high angle of incidences to properly determine emissivity.

14 SOLAR ENERGY↗

Growth of Epitaxial gamma-Al 2 O 3 Films on Rigid Single-Crystal Ceramic Substrates and Flexible, Single-Crystal-Like Metallic Substrates by Pulsed Laser Deposition

Epitaxial -Al2O3 thin films were grown on diverse substrates using pulsed laser deposition. The high quality of epitaxial growth and cubic structure of -Al2O3 films was confirmed by x-ray diffraction. SrTiO3 and MgO single crystal substrates were used to optimize the growth conditions for epitaxial -Al2O3 film. Under the optimized conditions, epitaxial -Al2O3 thin films were grown on flexible, single-crystal-like, metallic templates. These included untextured Hastelloy substrates with a biaxially textured MgO layer deposited using ion-beam-assisted-deposition and biaxially textured Ni-W metallic tapes with epitaxially grown and a biaxially textured, MgO buffer layer. These biaxially textured, -Al2O3 films on flexible, single-crystal-like substrates are promising for subsequent epitaxial growth of various complex oxide films used for electrical, magnetic and electronic device applications.

36 MATERIALS SCIENCE↗

Design and Control of Three-Dimensional Topological Magnetic Fields Using Interwoven Helical Nanostructures

Three-dimensional (3D) magnetic nanostructures are an emerging platform capable of creating complex topological magnetic fields. The control of localized nanoscale magnetic fields is seen to be of importance for diverse areas from bioapplications such as drug delivery, to particle trapping and controlling Majorana Fermions for quantum computing. Three-dimensional geometric confinement and proximity can create tailor-made spin textures not possible in two dimensions. The control of magnetization afforded here can allow the formation of unique stray field textures. Here, we report the creation of reconfigurable 3D topological magnetic field textures induced by an interwoven 3D nanostructure and applied field protocol. These field textures emerge due to distinct DWs formed in this structure and lead to the creation of an antivortex field, a hexapole cusp and a 3D skyrmion field tube of mixed chirality. In conclusion, our results therefore show a key step toward the design and control of topological magnetic fields on the nanoscale.

36 MATERIALS SCIENCE↗

Chemical disorder in topological insulators: A route to magnetism tolerant topological surface states

Here, we show that the chemical inhomogeneity in ternary three-dimensional topological insulators preserves the topological spin texture of their surface states against a net surface magnetization. The spin texture is that of a Dirac cone with helical spin structure in the reciprocal space, which gives rise to spin-polarized and dissipation-less charge currents. Thanks to the nontrivial topology of the bulk electronic structure, this spin texture is robust against most types of surface defects. However, magnetic perturbations break the time-reversal symmetry, enabling magnetic scattering and loss of spin coherence of the charge carriers. This intrinsic incompatibility precludes the design of magnetoelectronic devices based on the coupling between magnetic materials and topological surface states. We demonstrate that the magnetization coming from individual Co atoms deposited on the surface can disrupt the spin coherence of the carriers in the archetypal topological insulator Bi 2 Te 3 , while in Bi 2 Se 2 Te the spin texture remains unperturbed. This is concluded from the observation of elastic backscattering events in quasiparticle interference patterns obtained by scanning tunneling spectroscopy. The mechanism responsible for the protection is investigated by energy resolved spectroscopy and ab initio calculations, and it is ascribed to the distorted adsorption geometry of localized magnetic moments due to Se–Te disorder, which suppresses the Co hybridization with the surface states.

3D topological insulators↗

Chemo‐mechanical Alterations Induced From CO 2 Injection in Carbonate‐Cemented Sandstone: An Experimental Study at 71 °C and 29 MPa

Abstract Carbon capture, utilization, and storage may lead to mechanical degradation of the subsurface reservoir from fluid‐rock interaction, which could lead to wellbore instability or reservoir compaction. To better understand potential relationship between mechanical degradation with various carbonate cement textures and compositions in sandstone reservoirs, six flow‐through experiments were conducted. Formation water (TDS = 5,390 mg/L) enriched with CO 2 flowed through two types of Pennsylvanian Morrow B Sandstone: an ankerite‐siderite‐cemented sandstone (disseminated cement texture) and a calcite‐cemented sandstone (poikilotopic cement texture). The experiments produced little change in permeability in the ankerite‐siderite‐cemented sandstone, but permeability increased up to more than 1 order of magnitude in the calcite‐cemented sandstone. Ultrasonic measurements and cylinder‐splitting tests (also known as Brazilian tests) suggested negligible mechanical degradation of the ankerite‐siderite‐cemented sandstone. Variable changes, with significant mechanical degradation in the static moduli, were observed in the calcite‐cemented sandstone. Thus, dissolution of the disseminated ankerite‐siderite cement (0.28–0.30%) had minimal impact on modifying the flow network and the mechanical integrity of the sandstone, whereas dissolution of the poikilotopic calcite cement (0.89–1.13%, quantified with fluid chemistry and visualized with X‐ray microcomputed tomography) impacted the mechanical strength of the sandstone by disconnecting framework grains. With the high water‐to‐rock mass ratios (7.3–8.2) and number of pore volumes (147–675) employed in these experiments, potential risks are most relevant to regions near injection wells. Ultimately, the chemo‐mechanical effects induced by CO 2 injection are strongly influenced by the cement texture and composition and the burial history of the reservoir rock.

Wu, Z.↗

Reducing crystal symmetry to generate out-of-plane Dzyaloshinskii–Moriya interaction

The Dzyaloshinskii-Moriya antisymmetric exchange interaction (DMI) stabilises topological spin textures with promising future spintronics applications. According to crystal symmetry, the DMI can be categorized as four different types that favour different chiral textures. Unlike the other three extensively-investigated types, out-of-plane DMI, as the last type that favours in-plane chirality, remained missing so far. Here we apply point-group-dependent DMI matrix analysis to show that out-of-plane DMI exists under reduced crystal symmetry. Through strain and structure engineering, we show how C s symmetry is realized in ultrathin magnets and observe the out-of-plane DMI stabilised in-plane chirality using spin-polarized electron microscopy. Our results show that extremely low out-of-plane DMI strengths at µeV/atom are sufficient to stabilise topological spin textures, including merons and bimerons. We also demonstrate field-induced reversible control of the in-plane chirality and merons. Our findings open up untapped paths on topological magnetic textures and their potential applications.

36 MATERIALS SCIENCE↗

Creation of artificial skyrmions and antiskyrmions by anisotropy engineering

Topological spin textures form a fundamental paradigm in solid state physics and present unique opportunities to explore exciting phenomena such as the quantum Hall effect. One such non-trivial spin texture is a skyrmion, in which the spins can be mapped to point in all directions wrapping around a sphere. Understanding the formation of these spin textures, and their topological and energetic stability, is crucial in order to control their behavior. In this work, we report on controlling the anisotropy of continuous Co/Pt multilayer films with ion irradiation to form unique domain configurations of artificial skyrmions and antiskyrmions. We elucidate their behavior using aberration-corrected Lorentz transmission electron microscopy. We also discuss the energetic stability of these structures studied through in-situ magnetizing experiments performed at room temperature, combined with micromagnetic simulations that successfully reproduce the spin textures and behavior. As a result, this research offers new opportunities towards creation of artificial skyrmion or antiskyrmion lattices that can be used to investigate not only fundamental properties of their interaction with electron currents but also technological applications such as artificial magnonic crystals.

36 MATERIALS SCIENCE↗

Influence of high power impulse magnetron sputtering plasma ionization on the microstructure of TiN thin films

HIPIMS (High Power Impulse Magnetron Sputtering) discharge is a new PVD technology for the deposition of high-quality thin films. The deposition flux contains a high degree of metal ionization and nitrogen dissociation. The microstructure of HIPIMS-deposited nitride films is denser compared to conventional sputter technologies. However, the mechanisms acting on the microstructure, texture and properties have not been discussed in detail so far. In this study, the growth of TiN by HIPIMS of Ti in mixed Ar and N{sub 2} atmosphere has been investigated. Varying degrees of metal ionization and nitrogen dissociation were produced by increasing the peak discharge current (I{sub d}) from 5 to 30 A. The average power was maintained constant by adjusting the frequency. Mass spectrometry measurements of the deposition flux revealed a high content of ionized film-forming species, such as Ti{sup 1+}, Ti{sup 2+} and atomic nitrogen N{sup 1+}. Ti{sup 1+} ions with energies up to 50 eV were detected during the pulse with reducing energy in the pulse-off times. Langmuir probe measurements showed that the peak plasma density during the pulse was 3 x 10{sup 16} m{sup -3}. Plasma density, and ion flux ratios of N{sup 1+}: N{sub 2}{sup 1+} and Ti{sup 1+}: Ti{sup 0} increased linearly with peak current. The ratios exceeded 1 at 30 A. TiN films deposited by HIPIMS were analyzed by X-ray diffraction, and transmission electron microscopy. At high I{sub d}, N{sup 1+}: N{sub 2}{sup 1+} > 1 and Ti{sup 1+}: Ti{sup 0} > 1 were produced; a strong 002 texture was present and column boundaries in the films were atomically tight. As I{sub d} reduced and N{sup 1+}: N{sub 2}{sup 1+} and Ti{sup 1+}: Ti{sup 0} dropped below 1, the film texture switched to strong 111 with a dense structure. At very low I{sub d}, porosity between columns developed. The effects of the significant activation of the deposition flux observed in the HIPIMS discharge on the film texture, microstructure, morphology and properties are discussed.

36 MATERIALS SCIENCE↗

Disorder improves nanophotonic light trapping in thin-film solar cells

We present a systematic experimental study on the impact of disorder in advanced nanophotonic light-trapping concepts of thin-film solar cells. Thin-film solar cells made of hydrogenated amorphous silicon were prepared on imprint-textured glass superstrates. For periodically textured superstrates of periods below 500 nm, the nanophotonic light-trapping effect is already superior to state-of-the-art randomly textured front contacts. The nanophotonic light-trapping effect can be associated to light coupling to leaky waveguide modes causing resonances in the external quantum efficiency of only a few nanometer widths for wavelengths longer than 500 nm. With increasing disorder of the nanotextured front contact, these resonances broaden and their relative altitude decreases. Moreover, overall the external quantum efficiency, i.e., the light-trapping effect, increases incrementally with increasing disorder. Thereby, our study is a systematic experimental proof that disorder is conceptually an advantage for nanophotonic light-trapping concepts employing grating couplers in thin-film solar cells. The result is relevant for the large field of research on nanophotonic light trapping in thin-film solar cells which currently investigates and prototypes a number of new concepts including disordered periodic and quasi periodic textures.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Tuning the electronic properties at the surface of BaBiO{sub 3} thin films

The presence of 2D electron gases at surfaces or interfaces in oxide thin films remains a hot topic in condensed matter physics. In particular, BaBiO{sub 3} appears as a very interesting system as it was theoretically proposed that its (001) surface should become metallic if a Bi-termination is achieved (Vildosola et al., PRL 110, 206805 (2013)). Here we report on the preparation by pulsed laser deposition and characterization of BaBiO{sub 3} thin films on silicon. We show that the texture of the films can be tuned by controlling the growth conditions, being possible to stabilize strongly (100)-textured films. We find significant differences on the spectroscopic and transport properties between (100)-textured and non-textured films. We rationalize these experimental results by performing first principles calculations, which indicate the existence of electron doping at the (100) surface. This stabilizes Bi ions in a 3+ state, shortens Bi-O bonds and reduces the electronic band gap, increasing the surface conductivity. Our results emphasize the importance of surface effects on the electronic properties of perovskites, and provide strategies to design novel oxide heterostructures with potential interface-related 2D electron gases.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗