Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Solid”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,603 records · Page 89
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Structural, Electronic, and Photophysical Insights into a Few Atom Copper-Sulfur Cluster in the Solid and Solution States

Coinage-metal chalcogenide clusters are widely studied for their attractive photoluminescence properties. Copper chalcogenides are especially promising, but are often confined to solid-state investigations due to their limited solution stability and the difficulty of synthesizing stable, well-defined clusters. Here, we investigate copper–sulfur clusters incorporating a small number of Cu atoms to elucidate fundamental atomic interactions, ground- and excited-state characteristics, and photophysical behavior in both solid and solution. We have synthesized the Cu6(4,6-dimethyl-2-mercaptopyrimidine)6 cluster in both neutral and charged states, Cu6 and Cu6-2H2+, respectively, by selective ligand protonation. The molecular structures are determined using single-crystal X-ray diffraction, while Cu K-edge X-ray absorption spectroscopy is used to probe Cu electronic structure differences arising from the ligand modification. Steady-state and pump-probe optical spectroscopy is used to investigate photophysical properties, interpreted using density functional theory methods. Both clusters exhibit good stability in the solid state and in solution and show characteristic near-infrared emission with microsecond lifetimes. Overall, the Cu6S6 clusters display favorable charge–transfer characteristics and show potential for further use in driving photochemical transformations.

Copper-sulfur clusters↗
DOE OSTI2026

A Dendrite-Resistant Sodium/Porous-Carbon Anode for Solid-State Batteries – Strategies and Challenges for Low-Pressure Operation

Sodium solid-state batteries (Na-SSB) have gained interest recently due to the abundance of Na over Li, but they still tend to fail due to dendrites under practical current densities and cycling capacities. To overcome this, Na-SSBs are frequently tested with impractically high applied pressure. In this work, a porous carbon interfacial layer is utilized in conjunction with Na-ß”-Al2O3 solid electrolytes to enable Na-cycling at milder cell pressures. This sodium/porous carbon layer enables improved solid-state Na cycling in symmetric cells, up to a current density of 10 mA cm-2 at 25 °C. Cycling up to 1 mAh cm-2 is challenging with low pressure, but 1 mAh cm-2 capacity can be reliably cycled at 1 mA cm-2 at an elevated temperature of 60 °C in symmetric cells. Finally, the evolution of the interface and sodium/carbon anode is evaluated with cryogenic ion-milling and cross-sectional imaging revealing that, depending on testing temperature, pressure, current density, and capacity, void formation, Na-extraction from porous carbon, delamination of the porous carbon matrix, or a combination of these occurs at the interface between Na-metal and BASE. Despite this, excellent dendrite resistance is achieved, and a full-cell design utilizing a Na-transition metal oxide cathode is still able to achieve an areal capacity of ~ 2.7 mAh cm-2 at 0.125 mA cm-2. This work demonstrates an alternative pathway toward a Na-metal anode for Na-SSBs without the requirement of excessive stack pressure.

low-cost↗
DOE OSTI2023

Interphase Stabilization of LiNi 0.5 Mn 1.5 O 4 Cathode for 5 V–Class All–Solid–State Batteries

Employing high voltage cobalt-free spinel LiNi 0.5 Mn 1.5 O 4 (LNMO) as a cathode is promising for high energy density and cost-effectiveness, but it has challenges in all-solid-state batteries (ASSBs). Here, it is revealed that the limitation of lithium argyrodite sulfide solid electrolyte (Li 6 PS 5 Cl) with the LNMO cathode is due to the intrinsic chemical incompatibility and poor oxidative stability. Through a careful analysis of the interphase of LNMO, it is elucidated that even the halide solid electrolyte (Li 3 InCl 6 ) with high oxidative stability can be decomposed to form resistive interphase layers with LNMO in ASSBs. Interestingly, with Fe-doping and a Li 3 PO 4 protective layer coating, LNMO with Li 3 InCl 6 displays stable cycle performance with a stabilized interphase at a high voltage (≈4.7 V) in ASSBs. The enhanced interfacial stability with the extended electrochemical stability window through doping and coating enables high electrochemical stability with LNMO in ASSBs. Furthermore, this work provides guidance for employing high-voltage cathodes in ASSBs and highlights the importance of stable interphases to enable stable cycling in ASSBs.

25 ENERGY STORAGE↗
DOE OSTI2025

Tunable Crosslinked Ether Polymer Network Electrolytes for High‐Performance All‐Solid‐State Sodium Batteries

All-solid-state batteries (ASSBs) are critical for achieving high energy density and enhanced safety. Solid polymer electrolytes (SPEs) offer key advantages over other electrolytes, including improved safety, flexibility, and interfacial contact. Among the SPEs, ether-based polymers are widely studied due to their ease of processing and high ionic conductivity (σi) in the amorphous state. In this work, the introduction of poly(ethylene glycol) methyl ether methacrylate (PEGMEMA) into an SPE matrix composed of poly(ethylene glycol) diacrylate (PEGDA), poly(ethylene glycol) (PEG2k), and sodium bis(fluorosulfonyl)imide (NaFSI) salt is investigated to facilitate the formation of amorphous, high σ i SPEs through end-group engineering and polymer ratio optimization. PEGMEMA enhances structural integrity via crosslinking with PEGDA through its methacrylate group, while its methyl end group aids ion conduction. A 2:1:7 ratio of PEGDA:PEGMEMA:PEG2k exhibits a σi of 1.16 x 10 -4 S cm -1 and oxidative stability up to 4.4 V at 60 °C. A solid-state cell incorporating this SPE, a Na 2/3 Ni 1/3 Mn 2/3 O 2 (NM12) cathode, and a sodium-metal anode demonstrates excellent cycling stability, retaining over 80 % of its initial capacity for 150 cycles at 60 °C. The findings highlight the potential of end-group engineering in improving the electrochemical performance of SPEs.

25 ENERGY STORAGE↗
DOE OSTI2017

Vertically-aligned Mn(OH) 2 nanosheet films for flexible all-solid-state electrochemical supercapacitors

We report that the arrangement of the electrode materials is a significant contributor for constructing high performance supercapacitor. Here, vertically-aligned Mn(OH) 2 nanosheet thin films were synthesized by cathodic electrodeposition technique on flexible Au coated polyethylene terephthalate substrates. Morphologies, microstructures, chemical compositions and valence state of the nanosheet films were characterized systematically. It shows that the nanosheets arranged vertically to the substrate, forming a porous nanowall structures and creating large open framework, which greatly facilitate the adsorption or diffusion of electrolyte ions for faradaic redox reaction. Electrochemical tests of the films show the specific capacitance as high as 240.2 F g -1 at 1.0 A g -1 . The films were employed to assemble symmetric all-solid-state supercapacitors with LiCl/PVA gel severed as solid electrolyte. Finally, the solid devices exhibit high volumetric capacitance of 39.3 mF cm -3 at the current density 0.3 mA cm -3 with robust cycling stability. The superior performance is attributed to the vertically-aligned configuration.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Microstructure Analysis and Rheological Behavior of Magnesium Alloys at Semi-solid Temperature Range

Microstructure and rheological properties of AZ91 and Elektron 21 magnesium alloys in semi-solid state were studied. Differential scanning calorimetry revealed significant differences in melting range in analyzed materials. Isothermal annealing for 5, 30 and 80 min, in semi-solid range, corresponding to 50 and 70% of solid fraction, showed slower microstructure coarsening kinetics in Elektron 21 due to the presence of Zr- and RE-enriched precipitations. Ostwald ripening and coalescence resulted in decrease in grains density with increasing annealing time and temperature. Hardness after annealing showed overall tendency to diminish with soaking time probably due to the growth of average grain size. Rheological analysis showed tendency to lower the value of dynamic viscosity coefficient as shear rate rise, which confirmed non-Newtonian flow behavior. The highest values of dynamic viscosity coefficient were obtained for alloy AZ91.

36 MATERIALS SCIENCE↗
DOE OSTI2014

Temperature Dependence of the Mechanical Properties of Equiatomic Solid Solution Alloys with FCC Crystal Structures

We found that compared to decades-old theories of strengthening in dilute solid solutions, the mechanical behavior of concentrated solid solutions is relatively poorly understood. A special subset of these materials includes alloys in which the constituent elements are present in equal atomic proportions, including the high-entropy alloys of recent interest. A unique characteristic of equiatomic alloys is the absence of “solvent” and “solute” atoms, resulting in a breakdown of the textbook picture of dislocations moving through a solvent lattice and encountering discrete solute obstacles. Likewise, to clarify the mechanical behavior of this interesting new class of materials, we investigate here a family of equiatomic binary, ternary and quaternary alloys based on the elements Fe, Ni, Co, Cr and Mn that were previously shown to be single-phase face-centered cubic (fcc) solid solutions. The alloys were arc-melted, drop-cast, homogenized, cold-rolled and recrystallized to produce equiaxed microstructures with comparable grain sizes. Tensile tests were performed at an engineering strain rate of 10 -3 s -1 at temperatures in the range 77–673 K. Unalloyed fcc Ni was processed similarly and tested for comparison. The flow stresses depend to varying degrees on temperature, with some (e.g. NiCoCr, NiCoCrMn and FeNiCoCr) exhibiting yield and ultimate strengths that increase strongly with decreasing temperature, while others (e.g. NiCo and Ni) exhibit very weak temperature dependencies. Moreover, to better understand this behavior, the temperature dependencies of the yield strength and strain hardening were analyzed separately. Lattice friction appears to be the predominant component of the temperature-dependent yield stress, possibly because the Peierls barrier height decreases with increasing temperature due to a thermally induced increase of dislocation width. In the early stages of plastic flow (5–13% strain, depending on material), the temperature dependence of strain hardening is due mainly to the temperature dependence of the shear modulus. In all the equiatomic alloys, ductility and strength increase with decreasing temperature down to 77 K. Keywords

36 MATERIALS SCIENCE↗
DOE OSTI2015

Quantitative experimental determination of the solid solution hardening potential of rhenium, tungsten and molybdenum in single-crystal nickel-based superalloys

Here, the solid-solution hardening potential of the refractory elements rhenium, tungsten and molybdenum in the matrix of single-crystal nickel-based superalloys was experimentally quantified. Single-phase alloys with the composition of the nickel solid-solution matrix of superalloys were cast as single crystals, and tested in creep at 980 °C and 30–75 MPa. The use of single-phase single-crystalline material ensures very clean data because no grain boundary or particle strengthening effects interfere with the solid-solution hardening. This makes it possible to quantify the amount of rhenium, tungsten and molybdenum necessary to reduce the creep rate by a factor of 10. Rhenium is more than two times more effective for matrix strengthening than either tungsten or molybdenum. The existence of rhenium clusters as a possible reason for the strong strengthening effect is excluded as a result of atom probe tomography measurements. If the partitioning coefficient of rhenium, tungsten and molybdenum between the γ matrix and the γ' precipitates is taken into account, the effectiveness of the alloying elements in two-phase superalloys can be calculated and the rhenium effect can be explained.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Process-Structure-Property Relations for As-Deposited Solid-State Additively Manufactured High-Strength Aluminum Alloy

Solid-state additive manufacturing methods provide innovative solutions to circumvent problems associated with materials susceptible to hot cracking by avoiding liquid solid phase transformations. In this work, the process parameter influence on microstructural evolution and mechanical response of a fully dense aluminum alloy 7050 (AA7050) component manufactured via a rapid, solid-state additive manufacturing process known as Additive Friction Stir Deposition (AFS-D) was quantified for the first time. Three sections (starting dwell, transient, crossover of roads) of the deposition that exhibit differing thermomechanical processing histories were evaluated for the resulting microstructure and mechanical response. The microstructural characterization was performed on the as-deposited AA7050 via Electron Backscatter Diffraction (EBSD), TEM, optical microscopy, and Scanning Electron Microscopy (SEM). The microstructural characterization revealed refined constituent particles and grains throughout the as-deposited AA7050 microstructure. Furthermore, quasi-static tensile experiments were conducted in both the build and transverse directions, in order to quantify the orientation influence on tensile properties of the as-deposited AA7050 build. Spatially dependent tensile properties were observed in the material due to heat input variation coarsening of secondary phases towards the initial layers of the AFS-D build. Post-mortem analysis revealed that voids nucleated and coalesced from the overgrowth of the strengthening precipitates present in the material, resulting in fracture.

36 MATERIALS SCIENCE↗
DOE OSTI2025

A real-time distributed solid oxide electrolysis cell (SOEC) model for cyber-physical simulation

System integration and dynamic operability between SOEC and balance-of-plant (BoP) components are major technical challenges before realizing rapid load following of SOEC systems. Cyber-physical simulation (CPS) is a leading-edge digital engineering approach and is regarded as the next step beyond Digital Twins. CPS approach can be used to research SOEC system integration and develop dynamic controls prior to actual pilot testing without using a real SOEC. To seamlessly couple with BoP hardware and access non-observable operational parameters (e.g., local temperature gradient) during transients, a distributed one-dimensional (1D) real-time SOEC model was developed. Its real-time execution was demonstrated for 20 to 640 nodes at the fixed time step of 5 ms. A higher excess air ratio enabled smaller local temperature gradients on SOEC solid materials and faster transients upon current density step change from 0.15 to 0.55 A cm -2 . During the transients, the magnitude of the peak temperature gradient nearly doubled in 10 s from -3.5 to -5.9 °C cm -1 . This represents a significant operating risk that can impact the dynamic operability of SOEC systems. In addition, the local temperature gradient was found to change directions on all nodes in SOEC solid materials, with the greatest impact on the upstream nodes. The SOEC model was also tested at the thermal neutral voltage using actual process air flow parameters as variable model inputs. Variable process air temperatures were found to induce alternating local temperature gradients on SOEC solid materials. These are new operational mechanisms for SOEC degradation relevant for load following operational modes yet distinct from previous reports. To mitigate these unfavorable features, the SOEC can be operated at voltages that are slightly (±20 mV) deviated from the thermal neutral voltage. Here, the corresponding net thermal energy change was less than 1.6% of the electric power consumption. This 1D real-time SOEC model established the basis of cyber-physical simulation of SOEC hybrid systems.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2017

Study of aluminum particle combustion in solid propellant plumes using digital in-line holography and imaging pyrometry

The combustion of molten metals is an important area of study with applications ranging from solid aluminized rocket propellants to fireworks displays. Our work uses digital in-line holography (DIH) to experimentally quantify the three-dimensional position, size, and velocity of aluminum particles during combustion of ammonium perchlorate (AP) based solid-rocket propellants. Additionally, spatially resolved particle temperatures are simultaneously measured using two-color imaging pyrometry. To allow for fast characterization of the properties of tens of thousands of particles, automated data processing routines are proposed. In using these methods, statistics from aluminum particles with diameters ranging from 15 to 900 µm are collected at an ambient pressure of 83 kPa. In the first set of DIH experiments, increasing initial propellant temperature is shown to enhance the agglomeration of nascent aluminum at the burning surface, resulting in ejection of large molten aluminum particles into the exhaust plume. The resulting particle number and volume distributions are quantified. In the second set of simultaneous DIH and pyrometry experiments, particle size and velocity relationships as well as temperature statistics are explored. The average measured temperatures are found to be 2640 ± 282 K, which compares well with previous estimates of the range of particle and gas-phase temperatures. The novel methods proposed here represent new capabilities for simultaneous quantification of the joint size, velocity, and temperature statistics during the combustion of molten metal particles. The proposed techniques are expected to be useful for detailed performance assessment of metalized solid-rocket propellants.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Ab initio property predictions of quinary solid solutions using small binary cells

The Set of Small Ordered Structures (SSOS) approach is an ab initio technique for modelling random solid solutions in which many small structures are averaged so that their correlation functions match those of a desired composition. SSOS has been shown to be effective in reducing the cost of density functional theory calculations relative to other well-known techniques such as cluster expansions and special quasirandom structures for modelling solid solutions. Here in this work, we demonstrate that SSOS’s can be constructed using cells with only a subset of elements while still accurately modelling multi-component systems. Specifically, we show that small binary cells can effectively model two quinary high entropy alloys – NbTaTiHfZr and MoNbTaVW – accurately capturing properties such as formation energy, lattice parameters, elastic constants, and root-mean-square atomic displacements. Overall, this insight is useful for those looking to construct databases of such small structures for predicting the properties of multi-component solid solutions, as it greatly decreases the number of structures that needs to be considered.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Self-Stabilized LiNi 0.8 Mn 0.1 Co 0.1 O 2 in thiophosphate-based all-solid-state batteries through extra LiOH

Nickle-rich LiNi 0.8 Co 0.1 Mn 0.1 O 2 (NMC 811) cathode material exhibits engaging properties in high energy density and low cost, making it great potential for the next generation high-energy all-solid-state lithium batteries (ASSLBs). However, NMC 811 suffers from severe surface electrochemical, chemical, and voltage incompatibility towards solid-state electrolytes (SSE), especially thiophosphate-based electrolytes like Li 6 PS 5 Cl. Although diverse coating methods have been made to overcome this issue, they are typically cumbersome and expensive. A coating strategy that satisfied all the requirements of cost-efficiency, stability, uniformity, scalability, and easy-achieving is still challenging. Here, we developed a LiOH-based surface stabilization strategy that provides a ~10 nm stable permeable layer on NMC 811. After one-step sintering of NMC 811 precursor mixed with LiOH, which is commonly used for NMC 811 lithiation process, excessive LiOH simultaneously distributes on NMC 811 particles. Unlike other reported methods, this coating method can be easily controlled and fabricated without additional complicated processes. By simply controlling the thickness of LiOH layer, which protects the Li 6 PS 5 Cl solid electrolyte materials from being oxidized, optimized cycling stability can be obtained for 600 cycles with capacity of 130 mAh g – 1 on average at a wide electrochemical window of 2.50–4.20 V (vs. Li-In).

25 ENERGY STORAGE↗
DOE OSTI2015

Generalized gas-solid adsorption modeling: Single-component equilibria

Over the last several decades, modeling of gas–solid adsorption at equilibrium has generally been accomplished through the use of isotherms such as the Freundlich, Langmuir, Tóth, and other similar models. While these models are relatively easy to adapt for describing experimental data, their simplicity limits their generality to be used with many different sets of data. This limitation forces engineers and scientists to test each different model in order to evaluate which one can best describe their data. Additionally, the parameters of these models all have a different physical interpretation, which may have an effect on how they can be further extended into kinetic, thermodynamic, and/or mass transfer models for engineering applications. Therefore, it is paramount to adopt not only a more general isotherm model, but also a concise methodology to reliably optimize for and obtain the parameters of that model. A model of particular interest is the Generalized Statistical Thermodynamic Adsorption (GSTA) isotherm. The GSTA isotherm has enormous flexibility, which could potentially be used to describe a variety of different adsorption systems, but utilizing this model can be fairly difficult due to that flexibility. To circumvent this complication, a comprehensive methodology and computer code has been developed that can perform a full equilibrium analysis of adsorption data for any gas-solid system using the GSTA model. The code has been developed in C/C++ and utilizes a Levenberg–Marquardt’s algorithm to handle the non-linear optimization of the model parameters. Since the GSTA model has an adjustable number of parameters, the code iteratively goes through all number of plausible parameters for each data set and then returns the best solution based on a set of scrutiny criteria. Data sets at different temperatures are analyzed serially and then linear correlations with temperature are made for the parameters of the model. The end result is a full set of optimal GSTA parameters, both dimensional and non-dimensional, as well as the corresponding thermodynamic parameters necessary to predict the behavior of the system at temperatures for which data were not available. It will be shown that this code, utilizing the GSTA model, was able to describe a wide variety of gas-solid adsorption systems at equilibrium.In addition, a physical interpretation of these results will be provided, as well as an alternate derivation of the GSTA model, which intends to reaffirm the physical meaning.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2023

Steam explosion pretreatment coupling high-temperature short-time sterilization facilitating cellulose degradation and sporulation-regulatory gene expression in high-solid fermentation

Steam explosion coupling high-temperature short-time sterilization (SE-HTST) was exploited to modify cellulosic biomass medium properties and promote high-solid fermentation (HSF). Biomass characterization analysis showed that SE-HTST enlarged microstructural pores and cavities in solid media, providing more effective space for microbial growth. Meanwhile, SE-HTST helped to release glucose from the cellulose with 35.8 ± 4.5, 20.0 ± 2.3, and 12.3 ± 5.7 mg glucose/g dry medium at 24, 48, and 72 h of fermentation, which were 3.1, 2.3, and 1.5 times higher than that in medium from conventional thermal sterilization (CTS), respectively. SE-HTST increased the viable cell and spore number of Bacillus subtilis by 1.8 and 1.6 times at 72 h of fermentation compared to CTS. Moreover, the expressions of master transcriptional gene spo0A and the early sigma factors of sigF and sigE genes gradually increased in the SE-HTST medium, showing enhanced sporulation in HSF. Therefore, SE-HTST is an effective strategy for facilitating cellulose degradation, improving glucose nutrients in biomass medium, and promoting sporulation-regulatory gene expression during high-solid fermentation, which enhances the production of microbial ecological agents using B. subtilis significantly.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2018

All-solid-state asymmetric supercapacitor based on porous cobalt selenide thin films

As a significant semiconductor material, cobalt selenide has enormous potential and extensive application prospects in the field of solar cells, photocatalysis and supercapacitor. In this paper, porous CoSe thin films were successfully fabricated on stainless-steel sheet using a facile, effective electrodeposition technique. Electrochemical tests reveal that the specific capacitance reaches as high as 510 F g –1 at the current density of 1 A g –1 with the capacitance retention of 91% over 5000 cycles. An asymmetric all-solid-state supercapacitor is fabricated using CoSe thin film as the positive electrode and activate carbon as the negative electrode. The combined solid device displays a high area specific capacitance of 18.1 mF cm –2 accompanied with good cycling stability, outstanding flexibility and satisfactory mechanical stability. Furthermore, the solid devices connected in series can power the red light-emitting diodes. Here, the results show great potential for preparing large scale high energy density storage systems.

25 ENERGY STORAGE↗
DOE OSTI2021

A novel solid oxide electrolytic cell with reduced endothermic load for CO 2 electrolysis using (La 0.80 Sr 0.20 ) 0.95 MnO 3-δ cathode

CO 2 conversion to CO via solid oxide electrolysis provides a potentially efficient method for converting CO 2 into an industrially relevant product. A solid oxide electrolysis cell with (La 0.80 Sr 0.20 ) 0.95 MnO 3-δ (LSM) as the CO 2 reduction cathode, yttrium stabilized zirconia (YSZ) as electrolyte, and nickel as the H 2 oxidation anode was operated 800 °C and 850 °C. Thermogravimetric analysis of the LSM material showed no catalyst oxidation at operating temperatures allowing for CO 2 electrolysis without reducing safe gas. In addition, no cathode material mass gain was observed in the presence of CO suggesting little to no carbon deposition occurred above 750 °C. The formation rates of CO for the cell reached 1.15 mL∙min-1∙ cm -2 for an applied current of 150 mA∙cm -2 achieving a faradaic efficiency of 100 %. Furthermore, the cell displayed good stability in the short-term CO 2 electrolysis test with a nominal voltage drop of 4 mV h -1 for 10 h at 850°C. This study shows the feasibility of operating a solid oxide CO 2 electrolysis cell for CO production with H 2 at the anode to reduce endothermic process load.

(La0.80Sr0.20)0.95MnO3-δ↗
DOE OSTI2022

Deep eutectic solvent-based polymer electrolyte for solid-state lithium metal batteries

Poly(ethylene) oxide (PEO)-based electrolytes have been widely studied for solid-state lithium batteries while their ionic conductivity and lithium-ion transference number still need to be further improved. Herein, using the combined experimental and theoretical approach, we demonstrate a novel, solid-state PEO-deep eutectic solvent (DES) electrolyte for the first time. We found that the in situ formation of DES can reduce the crystallinity of PEO matrix and more Li + ions can move freely owing to the weakened coordination between ether oxygens and Li-ions. Besides, we show that more Li + ions can be dissociated from Li salts in PEO-DES electrolyte using the molecular dynamics simulations. Such liquid-free PEO-DES electrolytes showed good ionic conductivity (2.1 × 10 −4 S cm −1 ) which is 160% higher than that of conventional PEO-LiTFSI (8.1 × 10 −5 S cm −1 ) electrolyte at 60 °C. Additionally, the PEO-DES electrolyte showed 136% increase of Li-ion transference number (0.33) compared with ionic liquid-doped PEO-LiTFSI (0.14) at 60 °C. Moreover, the PEO-DES exhibited good compatibility with Li metal and stable Li plating/stripping behavior with little morphology change of Li metal. In conclusion, this research also provides new insights into the enhancement mechanisms of novel polymer electrolytes, improving our fundamental understanding of critical challenges that have impeded the adoption of solid-state lithium metal batteries.

Deep eutectic solvent↗