Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STALLING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,603 records · Page 89

Low-speed wind tunnel study of longitudinal stability and usable-lift improvement of a cranked wing

An exploratory low-speed investigation of a 70 deg/46 deg cranked-wing planform was undertaken to evaluate two vortex-control concepts aimed at alleviating a severe pitch up which limits the usable lift well below the C(sub L,max) of the basic wing. One concept was a strake-like extension introduced across the wing crank, whose vortex helps to stabilize the outer-wing flow and alleviate tip stall. The other was a lower-surface cavity flap employed to trap a vortex just beneath the inboard leading edge, resulting in reduced vortex lift over the inner-wing panel. Each of these concepts was shown to eliminate the high-alpha pitch up, potentially raising the maximum usable lift of the cranked wing practically to its C(sub L,max) value.

Rao, Dhanvada M.↗

Simulation investigation of the effect of the NASA Ames 80-by 120-foot wind tunnel exhaust flow on light aircraft operating in the Moffett field trafffic pattern

A preliminary study of the exhaust flow from the Ames Research Center 80 by 120 Foot Wind Tunnel indicated that the flow might pose a hazard to low-flying light aircraft operating in the Moffett Field traffic pattern. A more extensive evaluation of the potential hazard was undertaken using a fixed-base, piloted simulation of a light, twin-engine, general-aviation aircraft. The simulated aircraft was flown through a model of the wind tunnel exhaust by pilots of varying experience levels to develop a data base of aircraft and pilot reactions. It is shown that a light aircraft would be subjected to a severe disturbance which, depending upon entry condition and pilot reaction, could result in a low-altitude stall or cause damage to the aircraft tail structure.

Streeter, Barry G.↗

DC-10 winglet flight evaluation

Results of a flight evaluation of winglets on a DC-10 Series 10 aircraft are presented. For sensitive areas of comparison, effects of winglets were determined back-to-back with and without winglets. Basic and reduced-span winglet configurations were tested. After initial encounter with low-speed buffet, a number of acceptable configurations were developed. For maximum drag reduction at both cruise and low speeds, lower winglets were required, having leading edge devices on upper and lower winglets for the latter regime. The cruise benefits were enhanced by adding outboard aileron droop to the reduced-span winglet aircraft. Winglets had no significant impact on stall speeds, high-speed buffet boundary, and stability and control. Flutter test results agreed with predictions and ground vibration data. Flight loads measurement, provided in a concurrent program, also agreed with predictions. It was estimated that a production version of the aircraft, using the reduced-span winglet and aileron droop, would yield a 3-percent reduction in fuel burned with capacity payload. This range was 2% greater than with winglets. A 5% reduction in takeoff distance at maximum takeoff weight would also result.

Taylor, A. B.↗

Design of an Advanced Wood Composite Rotor and Development of Wood Composite Blade Technology

In support of a program to advance wood composite wind turbine blade technology, a design was completed for a prototype, 90-foot diameter, two-bladed, one-piece rotor, with all wood/epoxy composite structure. The rotor was sized for compatibility with a generator having a maximum power rating of 4000 kilowatts. Innovative features of the rotor include: a teetering hub to minimize the effects of gust loads, untwisted blades to promote rotor power control through stall, joining of blades to the hub structure via an adhesive bonded structural joint, and a blade structural design which was simplified relative to earlier efforts. The prototype rotor was designed to allow flexibility for configuring the rotor upwind or downwind of the tower, for evaluating various types of teeter dampers and/or elastomeric stops, and with variable delta-three angle settings of the teeter shaft axis. The prototype rotor was also designed with provisions for installing pressure tap and angle of attack instrumentation in one blade. A production version rotor cost analysis was conducted. Included in the program were efforts directed at developing advanced load take-off stud designs for subsequent evaluation testing by NASA, development of aerodynamic tip brake concepts, exploratory testing of a wood/epoxy/graphite concept, and compression testing of wood/epoxy laminate, with scarf-jointed plies.

Stroebel, Thomas↗

Flight characteristics of the AD-1 oblique-wing research aircraft

The AD-1 is a low-speed oblique-wing research airplane. This report reviews the vehicle's basic flight characteristics, including many aerodynamic, stability, and control effects that are unique to an oblique-wing configuration. These effects include the change in sideforce with angle of attack, moment changes with angle of attack and load factor, initial stall on the trailing wing, and inertial coupling caused by a roll-pitch cross product of inertia. An assessment of the handling qualities includes pilot ratings and comments. Ratings were generally satisfactory through 30 deg of wing sweep but degraded with increased sweep. A piloted simulation study indicated that a basic rate feedback control system could be used to improve the handling qualities at higher wing sweeps.

Sim, Alex G.↗

Transonic Navier-Stokes wing solutions using a zonal approach. Part 2: High angle-of-attack simulation

A computer code is under development whereby the thin-layer Reynolds-averaged Navier-Stokes equations are to be applied to realistic fighter aircraft configurations. This transonic Navier-Stokes code (TNS) utilizes a zonal approach in order to treat complex geometries and satisfy in-core computer memory constraints. The zonal approach was applied to isolated wing geometries in order to facilitate code development. The TNS finite difference algorithm, zonal methodology, and code validation with experimental data is addressed. Also addressed are some numerical issues such as code robustness, efficiency, and accuracy at high angles of attack. Special free-stream-preserving metrics proved an effective way to treat H-mesh singularities over a large range of severe flow conditions, including strong leading edge flow gradients, massive shock induced separation, and stall. Furthermore, lift and drag coefficients were computed for a wing up through CLmax. Numerical oil flow patterns and particle trajectories are presented both for subcritical and transonic flow. These flow simulations are rich with complex separated flow physics and demonstrate the efficiency and robustness of the zonal approach.

Chaderjian, Neal M.↗

Shock structure measured in a transonic fan using laser anemometry

Shock structure measurements acquired in a low aspect ratio transonic fan rotor are presented and analyzed. The rotor aspect ratio is 1.56 and the design tip relative Mach number is 1.38. The rotor flowfield was surveyed at near maximum efficiency and near stall operating conditions. Intra-blade velocity measurements acquired with a laser fringe anemometer on blade-to-blade planes in the supersonic region from 10 to 60 percent span are presented. The three-dimensional shock surface determined from the velocity measurments is used to determine the shock surface normal Mach number in order to properly calculate the ideal shock jump conditions. The ideal jump conditions are calculated based upon the Mach numbers measured on a surface of revolution and based upon the normal Mach number to indicate the importance of accounting for shock three dimensionality in turbomachinery design. Comparison of the shock locations with those predicted by a 3-D Euler code showed very good agreement and indicated the usefulness of integrating computational and experimental work to enhance the understanding of the flow physics occurring in transonic turbomachinery passages.

Wood, Jerry R.↗

Safe microburst penetration techniques: A deterministic, nonlinear, optimal control approach

A relatively large amount of computer time was used for the calculation of a optimal trajectory, but it is subject to reduction with moderate effort. The Deterministic, Nonlinear, Optimal Control algorithm yielded excellent aircraft performance in trajectory tracking for the given microburst. It did so by varying the angle of attack to counteract the lift effects of microburst induced airspeed variations. Throttle saturation and aerodynamic stall limits were not a problem for the case considered, proving that the aircraft's performance capabilities were not violated by the given wind field. All closed loop control laws previously considered performed very poorly in comparison, and therefore do not come near to taking full advantage of aircraft performance.

Psiaki, Mark L.↗

Symbolic generation of elastic rotor blade equations using a FORTRAN processor and numerical study on dynamic inflow effects on the stability of helicopter rotors

The process of performing an automated stability analysis for an elastic-bladed helicopter rotor is discussed. A symbolic manipulation program, written in FORTRAN, is used to aid in the derivation of the governing equations of motion for the rotor. The blades undergo coupled bending and torsional deformations. Two-dimensional quasi-steady aerodynamics below stall are used. Although reversed flow effects are neglected, unsteady effects, modeled as dynamic inflow are included. Using a Lagrangian approach, the governing equations are derived in generalized coordinates using the symbolic program. The program generates the steady and perturbed equations and writes into subroutines to be called by numerical routines. The symbolic program can operate on both expressions and matrices. For the case of hovering flight, the blade and dynamic inflow equations are converted to equations in a multiblade coordinate system by rearranging the coefficients of the equations. For the case of forward flight, the multiblade equations are obtained through the symbolic program. The final multiblade equations are capable of accommodating any number of elastic blade modes. The computer implementation of this procedure consists of three stages: (1) the symbolic derivation of equations; (2) the coding of the equations into subroutines; and (3) the numerical study after identifying mass, damping, and stiffness coefficients. Damping results are presented in hover and in forward flight with and without dynamic inflow effects for various rotor blade models, including rigid blade lag-flap, elastic flap-lag, flap-lag-torsion, and quasi-static torsion. Results from dynamic inflow effects which are obtained from a lift deficiency function for a quasi-static inflow model in hover are also presented.

Reddy, T. S. R.↗

Effect of variable inlet guide vanes on the operating characteristics of a tilt nacelle inlet/powered fan model

The effects of a variable inlet guide vane (VIGV) assembly on the operating characteristics of a V/STOL inlet and on the performance of a 20-in. (0.508-m) diameter fan engine were investigated. The data indicate that the VIGVs are effective thrust modulators over a wide range of free-stream velocities, nacelle angles of attack, and fan speeds. The thrust modulation ranges, including choking limits, fan stall limits, and inlet separation boundaries are presented. The presence of the VIGV assembly causes significant losses in inlet angle-of-attack capability and generally increases the blade stress levels at all limit conditions except at high angle of attack and high free-stream velocity. Reducing the fan nozzle exit area limited the positive VIGV actuation range and consequently decreased the range of thrust modulation at all limit conditions except at both high free-stream velocity and high angle of attack conditions.

Woollett, R. R.↗

Toward comparing experiment and theory for corroborative research on hingeless rotor stability in forward flight

For flap lag stability of isolated rotors, experimental and analytical investigations were conducted in hover and forward flight on the adequacy of a linear quasisteady aerodynamics theory with dynamic flow. Forward flight effects on lag regressing mode were emphasized. A soft inplane hingeless rotor with three blades was tested at advance ratios as high as 0.55 and at shaft angles as high as 20 deg. The 1.62 m model rotor was untrimmed with an essentially unrestricted tilt of the tip path plane. In combination with lag natural frequencies, collective pitch settings and flap lag coupling parameters, the data base comprises nearly 1200 test points (damping and frequency) in forward flight and 200 test points in hover. By computerized symbolic manipulation, a linear model was developed in substall to predict stability margins with mode identification. To help explain the correlation between theory and data it also predicted substall and stall regions of the rotor disk from equilibrium values. The correlation showed both the strengths and weaknesses of the theory in substall ((angle of attack) equal to or less than 12 deg).

Gaonkar, G.↗

An analysis of the crossover between local and massive separation on airfoils

Massive separation on airfoils operating at high Reynolds number is an important problem to the aerodynamicist, since its onset generally determines the limiting performance of an airfoil, and it can lead to serious problems related to aircraft control as well as turbomachinery operation. The phenomenon of crossover between local separation and massive separation on realistic airfoil geometries induced by airfoil thickness is investigated for low speed (incompressible) flow. The problem is studied both for the asymptotic limit of infinite Reynolds number using triple-deck theory, and for finite Reynolds number using interacting boundary-layer theory. Numerical results are presented which follow the evolution of the flow as it develops from a mildly separated state to one dominated by the massively separated flow structure as the thickness of the airfoil geometry is systematically increased. The effect of turbulence upon the evolution of the flow is considered, and the impact is significant, with the principal effect being the suppression of the onset of separation. Finally, the effect of surface suction and injection for boundary-layer control is considered. The approach which was developed provides a valuable tool for the analysis of boundary-layer separation up to and beyond stall. Another important conclusion is that interacting boundary-layer theory provides an efficient tool for the analysis of the effect of turbulence and boundary-layer control upon separated vicsous flow.

Barnett, M.↗

Numerical and physical aspects of aerodynamic flows III; Proceedings of the Third Symposium, California State University, Long Beach, CA, January 21-24, 1985

The present symposium considers hydrodynamic stability and turbulent transition, transition calculations in three-dimensional flows, a quasi-simultaneous finite difference approach for strongly interacting flows, the significance of the thin layer Navier-Stokes approximation, unsteady airfoil boundary layers, predictions and experiments on airfoils at low Reynolds numbers, and a comparison of interactive boundary layer and thin layer Navier-Stokes procedures. Also discussed are a viscous-inviscid interaction method for computing unsteady transonic separation, massive separation and dynamic stall on a cusped trailing edge airfoil, the computation of turbulent separated flows over wings, an iterative scheme for three-dimensional transonic flows, and the computation of three-dimensional flows with shock wave/boundary layer interaction. Many of the papers in this symposium were abstracted previously (cf., A85-42951).

Cebeci, T.↗

Exploratory wind-tunnel investigation of the stability and control characteristics of advanced general aviation configurations

Results of low-speed wind-tunnel investigations are presented for two general aviation configurations: the AVTEK canard configuration and the DeVore conventional configuration. Cooperative research programs were undertaken by industry and NASA to jointly conduct tests in the NASA Langley 12-Foot Low-Speed Wind Tunnel to explore stability and control characteristics of each configuration. A 1/5-scale AVTEK model and a 1/6-scale DeVore model were tested over an angle-of-attack range of up to 45 deg and an angle-of-sideslip range of up to 20 deg. Results from the AVTEK test are presented with an emphasis on the effects of configuration on the stall and poststall characteristics. Results from the DeVore test are presented with emphasis on the effects of wing leading-edge droop design on spin resistance characteristics.

Yip, L. P.↗

Special opportunities in helicopter aerodynamics

Aerodynamic research relating to modern helicopters includes the study of three dimensional, unsteady, nonlinear flow fields. A selective review is made of some of the phenomenon that hamper the development of satisfactory engineering prediction techniques, but which provides a rich source of research opportunities: flow separations, compressibility effects, complex vortical wakes, and aerodynamic interference between components. Several examples of work in progress are given, including dynamic stall alleviation, the development of computational methods for transonic flow, rotor-wake predictions, and blade-vortex interactions.

Mccroskey, W. J.↗

Numerical analysis of a NACA0012 airfoil with leading edge ice accretions

Analysis of a NACA0012 airfoil with leading edge ice has been performed using a Navier-Stokes code coupled with a grid generation code. The computed results were compared to experimental information obtained for an airfoil with a well defined artificial ice shape. The computations were performed at angles of attack ranging from zero to ten degrees. This range is sufficient to show the development of the separation bubble aft of the ice shape on both the upper and lower surfaces. Velocity profile plots in the separation bubble are examined in order to determine if recirculation patterns are predicted properly and if separation and reattachment points are found within the resolution of the experimental information. Also, the massive separation near the point of stall is examined in order to more accurately evaluate the lift coefficient curve in that region. Lift, drag, and moment coefficients are computed and compared to experiment.

Potapczuk, Mark G.↗

Further comparisons of interactive boundary-layer and thin-layer Navier-Stokes procedures

Calculations of the flows over NACA 4412 and GA(W)-2 airfoils with low-speed flow and over NACA 0012 and RAE 2822 airfoils with transonic flow are reported. They were obtained by solving potential flow and boundary-layer equations, and by solving thin-layer Navier-Stokes equations. The results cover a range of angles of attack up to and including stall and allow the evaluation of the numerical and physical features of the two solution methods. The agreement with measurements is acceptable except between the results of the thin Navier-Stokes equations and measurements in subsonic flow at high angles of attack. The interactive boundary-layer method is considerably more efficient requiring considerably less computer time and storage.

Chang, K. C.↗

A new method to predict unsteady aeroelastic behavior

A new method for predicting subsonic flutter and static deflections, including divergence, has been developed. The present method accounts for aspect ratio and, in the case of flutter, static deflections. The angle of attack is limited only by the occurrence of stall or vortex bursting near the wing. The innovation in the present method is to integrate simultaneously and interactively the equations of motion of the structure and the flowfield. The present approach employs an iterative scheme based on the predictor-corrector method. The general unsteady vortex-lattice method (UVLM) is used to predict the aerodynamic loads. Because the UVLM predicts the wakes as part of the solution, the history of the motion is taken into account; hysteresis is predicted. The deflection (for both bending and torsion) is expressed as an expansion in terms of the free-vibration modes. The time-dependent coefficients in these expansions serve as the generalized coordinates. Numerical examples illustrating the calculation of static deflections and transient dynamic responses above and below the flutter boundary are included.

Strganac, Thomas W.↗