Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Mount”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,603 records · Page 89
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Ultrasonic scanner for radial and flat panels

An ultrasonic scanning mechanism is described that scans panels of honeycomb construction or with welded seams. It incorporates a device which by simple adjustment is adapted to scan either a flat panel or a radial panel. The supporting structure takes the form of a pair of spaced rails. An immersion tank is positioned between the rails and below their level. A work holder is mounted in the tank and is adapted to hold the flat or radial panel. A traveling bridge is movable along the rails and a carriage is mounted on the bridge.

Spencer, R. L.↗
NASA NTRS1974

Wind tunnel blockage and support interference effects on winged-body models at Mach numbers from 0.6 to 1.0

Three sting-mounted winged-body models with tunnel blockages of 0.1, 1.0, and 2.0 percent were tested in the Lewis Research Center's 8- by 6- Foot Supersonic Wind Tunnel. Fuselage pressures were obtained over a Mach number range of 0.6 to 1.0 at angles of attack from 0 deg to 4 deg. Two other types of model support were investigated, which included simulated wing-tip and fuselage support-strut mountings. The effects of tunnel porosity and sidewall geometry were also investigated. Model blockage effects were small up to M sub 0 = 0.95. At higher speeds the major blockage effect observed was a displacement of the local transonic terminal shocks on the model. The effects of the wing-tip type of model support were small up to M sub 0 = 0.95, but disturbances were observed on the fuselage at higher speeds. Changes in local tunnel porosity were effective in reducing the disturbances up to M sub 0 = 0.975, but a change in sidewall geometry was not.

Blaha, B. J.↗
NASA NTRS1974

Venting characteristics of gaseous helium and nitrogen discharging into a free stream at Mach numbers from 0.60 to 1.57

An experimental investigation was conducted in the Lewis Research Center 8- by 6-Foot Supersonic Wind Tunnel to compare the effects on discharge coefficient of venting gaseous helium and gaseous nitrogen into a free stream. The test was conducted from Mach 0.06 to 1.57 with the vent mounted in a flat plate. The plate was strut mounted to the tunnel ceiling and at a 0 angle of attack. The gases were discharged from a plenum chamber through a 2.54-centimeter (1.00-in.) diameter vent. The ratio of local static pressure to plenum pressure was varied from 0.51 to 0.975. The ratio of boundary layer thickness to vent diameter varied from a maximum of 1.34 at Mach 0.60 to a minimum of 0.55 at Mach 1.37.

Johns, A. L.↗
NASA NTRS1974

Grinding arrangement for ball nose milling cutters

A grinding arrangement for spiral fluted ball nose end mills and like tools includes a tool holder for positioning the tool relative to a grinding wheel. The tool is mounted in a spindle within the tool holder for rotation about its centerline and the tool holder is pivotably mounted for angular movement about an axis which intersects that centerline. A follower arm of a cam follower secured to the spindle cooperates with a specially shaped cam to provide rotation of the tool during the angular movement of the tool holder during the grinding cycle, by an amount determined by the cam profile. In this way the surface of the cutting edge in contact with the grinding wheel is maintained at the same height on the grinding wheel throughout the angular movement of the tool holder during the grinding cycle.

Burch, C. F.↗
NASA NTRS1972

Space shuttle system program definition. Volume 1: Executive summary

A study for the selection of a low cost shuttle system for design and development was conducted. The objective of the final study was to examine and penetrate the major technical and cost issues affecting the choice of the following: (1) liquid propulsion recoverable or solid propulsion recoverable booster, (2) parallel burn/parallel mount or series burn/tandem mount configurations, and (3) payload weight and payload bay size of the orbiter. The matrix of program options which were considered in the study is developed.

Source record↗
NASA NTRS1974

Deployable flexible ventral fins for use as an emergency spin recovery device in aircraft

A flexible fin device for mounting on an aircraft to effect spin recovery is described. The device may be selectively deployed to provide a triangular planform of flexible material to provide spin recovery, and retracted for compact storage during non-use. A single flexible fin may be deflected in a specific direction depending on direction of spin rotation, or two flexible fins forming an inverted V configuration may be used. The device is mounted on the underbody of the aircraft.

Burk, S. M., Jr.↗
NASA NTRS1974

Apparatus for forming drive belts

An apparatus for manufacturing belts, such as seamless belts, is provided, the apparatus has relatively movable rollers that are mounted in an oven. A belt blank, for example, of a thin polyester film, is rotated on the rollers as heat is applied. Four rollers, each mounted on a separate roller assembly, are movable along appropriate tracks while a fifth centrally located roller is stationary. A pair of dc motors are operatively connected to a speed reduction gear assembly to provide a pair of rotating drive shafts that extend into the oven. One rotating shaft drives all of the rollers through a rotational gear assembly while the other drive shaft is capable of positioning the movable rollers through respective rotating threaded shafts. Control devices are provided for controlling the motors while measuring devices are operatively connected to the positional drive shaft to indicate the position of the rollers.

Topits, A., Jr.↗
NASA NTRS1974

Investigation of space shuttle orbiter subsonic stability and control characteristics in the NAAL low speed wind tunnel (OA62B), volume 2

Experimental aerodynamic investigations were conducted on a sting-mounted 0.0405 scale representation of the 140A/B space shuttle orbiter in a 7.75 ft by 11 ft low speed wind tunnel during the period from November 14, 1973 to December 6, 1973. Establishment of basic longitudinal stability characteristics in and out of ground effect, and the establishment of lateral-directional stability characteristics in free air were the primary test objectives. The following effects and configurations were tested: (1) two dual podded nacelle configurations; (2) stability and control characteristics at nominal elevon deflections, rudder deflections, airleron deflections, rudder flare angles, and body flap deflections; (3) effects of various elevon and elevon/fuselage gaps on longitudinal stability and control; (4) pressures on the vertical tail at spanwise stations using pressure bugs; (5) aerodynamic force and moment data measured in the stability axis system by an internally mounted, six-component strain gage balance. For Vol. 1, see N74-32324.

Mennell, R.↗
NASA NTRS1974

Investigation of space shuttle orbiter subsonic stability and control characteristics and determination of control surface hinge moments in the Rockwell International low speed wind tunnel (OA37)

Experimental aerodynamic investigations were conducted on a string-mounted 0.030 scale representation of the 140A/B space shuttle orbiter in the 7.75- by 11-foot low speed wind tunnel. The primary test objectives were to establish basic longitudinal and lateral directional stability and control characteristics for the basic configuration plus control surface hinge moments. Aerodynamic force and moment data were measured in the body axis system by an internally mounted, six-component strain gage balance. Additional configurations investigated were sealed rudder hingeline gaps, sealed elevon gaps and compartmentized speedbrakes.

Hughes, T.↗
NASA NTRS1974

Feasibility study of the transonic biplane concept for transport aircraft application

Investigations were conducted to evaluate the feasibility of a transonic biplane consisting of a forward-mounted swept-back lower wing, a rear-mounted swept-forward upper wing, and a vertical fin connecting the wings at their tips. This wing arrangement results in significant reductions in induced drag relative to a monoplane designed with the same span, and it allows for a constant-section fuselage shape while closely matching an ideal area distribution curve for M = 0.95 cruise. However, no significant reductions in ramp weight were achieved for the biplane relative to a monoplane with the same mission capability. Flutter analyses of the biplane revealed both symmetric and antisymmetric instabilities that occur well below the required flutter speed. Further studies will be required to determine if acceptable flutter speeds can be achieved through the elimination of the instabilities by passive means or by active controls. Configurations designed for other missions, especially those with lower Mach numbers and lower dynamic pressures, should be examined since the geometries suitable for those design constraints might avoid the weight penalties and flutter instabilities which prevent exploitation of induced drag benefits for the configuration studied.

Lange, R. H.↗
NASA NTRS1974

Lift-induced wing-tip vortex attenuation

It has been shown by a new static airflow visualization method that a drogue device properly positioned downstream of the wing tip causes vortex breakdown. This same result has been obtained by mounting a jet engine simulator at the wing tip and directing the high-energy jet blast downstream into the vortex. These configurations, among others, are now under intensive investigation in the new Langley Vortex Research Facility. In this facility a balance mounted vortex generating model is propelled along the 1800-foot track while a second model trailed at 160 feet (scale distance of 1 mile) measures the far-field rolling moment induced by the vortex of the generating model.

Patterson, J. C., Jr.↗
NASA NTRS1974

Radar measurement of soil moisture content

The effect of soil moisture on the radar backscattering coefficient was investigated by measuring the 4- to 8-GHz spectral response from two types of bare-soil fields: slightly rough and very rough, in terms of the wavelength. An FM-CW radar system mounted atop a 75-ft truck-mounted boom was used to measure the return at ten frequency points across the 4- to 8-GHz band, at eight different look angles (0 through 70 deg), and for all polarization combinations. A total of 17 sets of data were collected covering the range from 4 to 36% soil moisture content by weight. The results indicate that the radar response to soil moisture content is highly dependent on the surface roughness, microwave frequency, and look angle. The response seems to be linear, however, over the range from 15 to 30% moisture content for all angles, frequencies, polarizations and surface conditions.

Ulaby, F. T.↗
NASA NTRS1974

A technique for generating shear waves in cylindrical shells under radial impact

Experimental techniques are developed to study and measure the shear-wave velocity in an aluminum cylindrical shell subjected to a radial impact. The radial impact is obtained by exploding an electrical detonator inserted in plastic plugs mounted on the end of the shell. Strain gages, mounted on the outside surface of the shell at various axial locations, are used to obtain oscilloscope traces from which the shear-wave velocity can be calculated.

Blum, A.↗
NASA NTRS1975

Four-dimensional worldwide atmospheric models: ANYPT and ANYRG

Computer programs read magnetic-tape data bases and computer meteorological profiles for any position, time, and height (from zero to 25 km). System assists in analyses of distortion of information obtained from aircraft-mounted or spacecraft-mounted electromagnetic sensors.

Johnson, D.↗
NASA NTRS1975

An experimental 100 kilowatt wind turbine generator

Experimental generator consists of two blades mounted on 100 foot tower, driving transmission train and electric generator mounted on top of tower. Machine generates 100 kW of electricity at wind speeds from 18 to 60 miles per hour. Yaw control mechanism automatically orients machine into wind.

Thomas, R. L.↗
NASA NTRS1974

Effect of ELEVON gap configurations on the longitudinal stability and control effectiveness of the 43-0 space shuttle orbiter (OA118)

Experimental aerodynamic investigations were conducted on a stingmounted 0.0405-scale representation of the 140A/B space shuttle orbiter in a 7.75 by 11-Foot low speed wind tunnel from April 24 to April 26, 1974. Differential inboard/outboard elevon panel deflections with the 6-inch gap were investigated to determine outboard panel aileron effectiveness. The elevons were deflected from +20 degrees to -40 degrees in various combinations. Aerodynamic force and moment data for the orbiter were measured in the body axis system by an internally mounted, six-component strain gage balance. The model was sting mounted with the center of rotation located at F.S. 60.172. The angle of attack range was from -10 degrees to +24 degrees.

Hughes, T.↗
NASA NTRS1973

The 8-18 GHz radar spectrometer

The design, construction, testing, and accuracy of an 8-18 GHz radar spectrometer, an FM-CW system which employs a dual antenna system, is described. The antennas, transmitter, and a portion of the receiver are mounted at the top of a 26 meter hydraulic boom which is in turn mounted on a truck for system mobility. HH and VV polarized measurements are possible at incidence angles ranging from 0 deg. to 80 deg. Calibration is accomplished by referencing the measurements against a Luneberg lens of known radar cross section.

Bush, T. F.↗