Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Microstructure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,603 records · Page 89

Study of the effects of gaseous environments on the hot corrosion of superalloy materials

The effect of the gaseous corrodent NaCl on the high temperature oxidation and sodium sulfate induced hot corrosion behavior of alumina formers, chromia formers, and the superalloy B-1900 was examined. Isothermal experiments were conducted at 900 C and 1050 C in air in the presence and absence of NaCl vapors. Microstructural changes in oxide morphology and increased rates of oxidation were observed when NaCl(g) was present. It is hypothesized that the accelerated rates of oxidation are the result of removal of aluminum from the scale substrate interface and the weakening of the scale substrate bonds. The aluminum removed was redeposited on the surfaces in the form of alumina whiskers. For the superalloy B-1900, alumina whiskers are also formed, and the alloy oxidizes at catastrophic rates. In the case of Ni-25Cr alloy, NaCl vapors interact with the scale depleting it of chromium.

Smeggil, J. G.↗

State of the mineral component of rat bone tissue during hypokinesia and the recovery period

Experiments were conducted on young growing rats. Hypokinesia lasting from 20 to 200 days caused retarded gain in weight and volume of the femur and delayed development of the cortical layer of the diaphysis. In contrast, the density of the cortical layer of the femoral diaphysis increased due to elevation of the mineral saturation of the bone tissue microstructures. Incorporation of Ca into the bone tissue in hypokinesia had a tendency to reduce. Partial normalization of the bone tissue mineral component occurred during a 20 day recovery period following hypokinesia.

Volozhin, A. I.↗

Dynamic Modulus and Damping of Boron, Silicon Carbide, and Alumina Fibers

The dynamic modulus and damping capacity for boron, silicon carbide, and silicon carbide coated boron fibers were measured from-190 to 800 C. The single fiber vibration test also allowed measurement of transverse thermal conductivity for the silicon carbide fibers. Temperature dependent damping capacity data for alumina fibers were calculated from axial damping results for alumina-aluminum composites. The dynamics fiber data indicate essentially elastic behavior for both the silicon carbide and alumina fibers. In contrast, the boron based fibers are strongly anelastic, displaying frequency dependent moduli and very high microstructural damping. Ths single fiber damping results were compared with composite damping data in order to investigate the practical and basic effects of employing the four fiber types as reinforcement for aluminum and titanium matrices.

Dicarlo, J. A.↗

Experimental laboratory measurement of thermophysical properties of selected coal types

A number of bituminous coals of moderate to high plasticity were examined, along with portions of their extrudates from the JPL 1.5-inch 850 F screw extruder. Portions of the condensed pyrolysis liquids released during extrusion, and of the gaseous products formed during extrusion were also analyzed. In addition to the traditional determinations, the coals and extrudates were examined in terms of microstructure (especially extractable fractions), thermal analysis (especially that associated with the plastic state), and reactivity towards thermal and catalyzed hydroliquefaction. The process of extrusion increases the fixed carbon content of coals by about 5% and tends to increase the surface area. Coals contaning 25% or more DMF-extractable material show an increase in extractables as a result of extrusion; those initially containing less than 20% extractables show a decrease as a result of extrusion. Both the raw and extruded samples of Kentucky #9 coal are highly reactive towards hydroliquefaction, undergoing conversions of 75 to 80% in 15 min and 85-94% in 60 min in a stirred clave.

Lloyd, W. G.↗

Application of superalloy powder metallurgy for aircraft engines

In the last decade, Government/Industry programs have advanced powder metallurgy-near-net-shape technology to permit the use of hot isostatic pressed (HIP) turbine disks in the commercial aircraft fleet. These disks offer a 30% savings of input weight and an 8% savings in cost compared in cast-and-wrought disks. Similar savings were demonstrated for other rotating engine components. A compressor rotor fabricated from hot-die-forged-HIP superalloy billets revealed input weight savings of 54% and cost savings of 35% compared to cast-and-wrought parts. Engine components can be produced from compositions such as Rene 95 and Astroloy by conventional casting and forging, by forging of HIP powder billets, or by direct consolidation of powder by HIP. However, each process produces differences in microstructure or introduces different defects in the parts. As a result, their mechanical properties are not necessarily identical. Acceptance methods should be developed which recognize and account for the differences.

Dreshfield, R. L.↗

Acoustic emission from composite materials

The two basic areas where the acoustic emission (AE) technique can be applied are materials research and the evaluation of structural reliability. This experimental method leads to a better understanding of fracture mechanisms and is an NDT technique particularly well suited for the study of propagating cracks. Experiments are described in which acoustic emissions were unambiguously correlated with microstructural fracture mechanisms. The advantages and limitations of the AE technique are noted.

Visconti, I. C.↗

Equilibrium geochemical modeling of a seasonal thermal energy storage aquifer field test

A geochemical mathematical modeling study designed to investigate the well plugging problems encountered at the Auburn University experimental field tests is summarized. The results, primarily of qualitative interest, include: (1) loss of injectivity was probably due to a combination of native particulate plugging and clay swelling and dispersion; (2) fluid-fluid incompatibilities, hydrothermal reactions, and oxidation reactions were of insignificant magnitude or too slow to have contributed markedly to the plugging; and (3) the potential for and contributions from temperature-induced dissolved gas solubility reductions, capillary boundary layer viscosity increases, and microstructural deformation cannot be deconvolved from the available data.

Stottlemyre, J. S.↗

Development of improved-durability plasma sprayed ceramic coatings for gas turbine engines

As part of a NASA program to reduce fuel consumption of current commercial aircraft engines, methods were investigated for improving the durability of plasma sprayed ceramic coatings for use on vane platforms in the JT9D turbofan engine. Increased durability concepts under evaluation include use of improved strain tolerant microstructures and control of the substrate temperature during coating application. Initial burner rig tests conducted at temperatures of 1010 C (1850 F) indicate that improvements in cyclic life greater than 20:1 over previous ceramic coating systems were achieved. Three plasma sprayed coating systems applied to first stage vane platforms in the high pressure turbine were subjected to a 100-cycle JT9D engine endurance test with only minor damage occurring to the coatings.

Sumner, I. E.↗

Method of mitigating titanium impurities effects in p-type silicon material for solar cells

Microstructural evaluation tests performed on Cu-doped, Ti-doped and Cu/Ti doped p-type silicon single crystal wafers, before and after the solar cell fabrication, and evaluation of both dark forward and reverse I-V characteristic records for the solar cells produced from the corresponding silicon wafers, show that Cu mitigates the unfavorable effects of Ti, and thus provides for higher conversion efficiency, thereby providing an economical way to reduce the deleterious effects of titanium, one of the impurities present in metallurgical grade silicon material.

Salama, A. M.↗

SPAR 5 experiment no. 74-30 agglomeration in immiscible liquids

The influence of gravity, cooling rate, and composition on the macro-and microstructure of liquid phase immiscible alloys were researched. Aluminum indium alloys of compositions 30, 40, 70, and 90 weight percent indium were processed aboard two sounding rocket flights, SPAR 2 and SPAR 5. Radiographic and metallographic examination of the SPAR 2 flight and ground base samples showed the expected separation at lg of the ground base alloys into indium rich and aluminum rich layers. The flight alloys produced an aluminum rich core surrounding by indium rich metal. The results obtained from the SPAR 5 40 and 70 weight percent indium alloys were essentially identical to those from SPAR 2. The 30 and 90 weight percent indium alloys also showed massive separation into configuration similar to the 40 and 70 weight percent indium alloys. The 90 weight percent indium alloy showed additional evidence that surface tension induced droplet migration had occurred in this alloy which could at least in part account for the observed structures.

Gelles, S.↗

State-of-the-art SiAlON materials

The state of the art of SiAlONs is examined. The review includes work on phase relations, crystal structure, synthesis, fabrication, and properties of various SiAlONs. The essential features of compositions, fabrication methods, and microstructure are reviewed. High temperature flexure strength, creep, fracture toughness, oxidation, and thermal shock resistance are discussed. These data are compared to those for some currently produced silicon nitride ceramics to assess the potential of SiAlON materials for use in advanced gas turbine engines.

Dutta, S.↗

Effects of factors of prolonged space flight on conditions of tortoise skeleton

After a 60-90 day space flight mild osteoporosis developed in the epiphyses and metaphyses of long tubular bones of tortoises, which was not attributed to reduced mineral saturation of the preserved bone tissue microstructures. The diminished strength of the cancellous bone of the epiphyses in tortoises after space flight was due to the reduced properties of its structure. The strength of the compact substance did not change under the effect of weightlessness.

Stupakon, G. P.↗

Fatigue behavior of SiC reinforced titanium composites

The low cycle axial fatigue properties of 25 and 44 fiber volume percent SiC/Ti(6Al-4V) composites were measured at room temperature and at 650 C. At room temperature, the S-N curves for the composites showed no anticipated improvement over bulk matrix behavior. Although axial and transverse tensile strength results suggest a degradation in SiC fiber strength during composite fabrication, it appears that the poor fatigue life of the composites was caused by a reduced fatigue resistance of the reinforced Ti(6Al-4V) matrix. Microstructural studies indicate that the reduced matrix behavior was due, in part, to the presence of flawed and fractured fibers created near the specimen surfaces by preparation techniques. Another possible contributing factor is the large residual tensile stresses that can exist in fiber-reinforced matrices. These effects, as well as the effects of fatigue testing at high temperature, are discussed.

Bhatt, R. T.↗

Characterization and properties of controlled nucleation thermochemical deposited /CNTD/ silicon carbide

Results are presented for an investigation designed to characterize the microstructure of controlled nucleation thermomechanical deposition (CNTD) produced SiC material with respect to grain structure, stoichiometry, phase analysis, etc., and to evaluate the room-temperature and high-temperature fracture and oxidation behavior. By using the CNTD process, ultrafine-grained SiC is deposited on tungsten wires as substrates, with superior surface smoothness and without the macrocolumnar growth commonly observed in conventional CVD materials. The results suggest that the high-purity, fully dense, and stable grain size SiC material produced by CNTD shows potential for high-temperature structural applications, provided that pertinent problems are resolved.

Dutta, S.↗

State-of-the-art of SiAlON materials

The state of the art of 'SiAlONs' is reviewed, noting that the term has become a generic one applied to Si3N4 based materials. Attention is given to work on phase relations, crystal structure, synthesis, fabrication, and properties of various SiAlONs. Also discussed are the essential features of compositions, fabrication methods, and microstructures. In addition, consideration is given to high temperature flexure strength, creep, fracture toughness, oxidation, and thermal shock resistance. Finally, these data are compared to those for some currently produced silicon nitride ceramics to assess the potential of SiAlON materials for use in advanced gas turbine engines.

Dutta, S.↗

Some TEM observations of Al2O3 scales formed on NiCrAl alloys

The microstructural development of Al2O3 scales on NiCrAl alloys has been examined by transmission electron microscopy. Voids have been observed within grains in scales formed on a pure NiCrAl alloy. Both voids and oxide grains grew measurably with oxidation time at 1100 C. The size and amount of porosity decreased towards the oxide-metal growth interface. It was postulated that the voids resulted from an excess number of oxygen vacancies near the oxide-metal interface. Short-circuit diffusion paths were discussed in reference to current growth stress models for oxide scales. Transient oxidations of pure, Y-doped, and Zr-doped NiCrAl was also examined. Oriented alpha-(Al,Cr)2O3 and Ni(Al,Cr)2O4 scales often coexisted in layered structures on all three alloys. Close-packed oxygen planes and directions in the corundum and spinel layers were parallel. The close relationships between oxide layers provided a gradual transition from initial transient scales to steady state Al2O3 growth.

Smialek, J.↗

Recent developments in liquid-metal embrittlement

The paper reviews developments in liquid-metal embrittlement of the past 7 years including data on cyclic loading. Embrittlement by solid and liquid metals and by hydrogen has many common features, although the mechanism of embrittler transport differs. Fracture may occur in each type of embrittlement by environmentally assisted shear and by reduced cohesion; embrittlement under cyclic loading has been widely observed, with stress level, temperature, and substrate alloy composition and grain size being the major variables. The degree of embrittlement between any combination of environment (i.e. hydrogen, liquid metal, or solid metal) and substrate depends upon the strength of the interaction with the substrate, the kinetics of embrittler transport, the mutual solubility of embrittler and substrate, and a large number of test and microstructural conditions. A method of calculating the most significant of these variables and the strength of interaction was reviewed and predictions of embrittlement in previously untested couples were made.

Stoloff, N. S.↗