SEARCH · Engineering Papers

Results for “LOADING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,603 records · Page 89

All sources NASA NTRS DOE OSTI

NASA NTRS1973

Plastic intensity factors for cracked plates subjected to biaxial loading

An elastic-plastic analysis is performed for an infinite plate under plane stress conditions which contains a finite line crack and is subjected to biaxial loading. In the large scale yielding range, the amplitude of the dominant singularity at the crack tip, the plastic stress (or strain) intensity factor, is found to depend on the magnitude of loading parallel to the crack direction. The predicted value for the fracture initiation stress which is based on a plastic intensity factor fracture criterion, increases under lateral, tensile loading. Compressive loading parallel to the crack has the opposite effect on the fracture initiation stress.

Hilton, P. D.↗

NASA NTRS1973

Sea level side loads in high-area-ratio rocket engines

An empirical separation and side load model to obtain applied aerodynamic loads has been developed based on data obtained from full-scale J-2S (265K-pound-thrust engine with an area ratio of 40:1) engine and model testing. Experimental data include visual observations of the separation patterns that show the dynamic nature of the separation phenomenon. Comparisons between measured and applied side loads are made. Correlations relating the separation location to the applied side loads and the methods used to determine the separation location are given.

Nave, L. H.↗

NASA NTRS1974

Selection of appropriate test method for simulating steady-state spacecraft launch loads

In ground testing prior to launch the static loads portion of the launch profile may be simulated by either applying static loads directly to the spacecraft through an appropriate loading facility or by subjecting the spacecraft to acceleration loads on a centrifuge. The factors to be considered in selecting one of the two simulation methods are discussed, giving attention to the relative advantages of the two methods in each case.

Shockey, E. F.↗

NASA NTRS1974

SSME/side loads analysis for flight configuration, revision A

This document describes the dynamic loads analysis accomplished for the Space Shuttle Main Engine (SSME) considering the side load excitation associated with transient flow separation on the engine bell during ground ignition. The results contained herein pertain only to the flight configuration. A Monte Carlo procedure was employed to select the input variables describing the side load excitation and the loads were statistically combined. This revision includes an active thrust vector control system representation and updated orbiter thrust structure stiffness characteristics. No future revisions are planned but may be necessary as system definition and input parameters change.

Holland, W.↗

NASA NTRS1975

Supersonic flutter of panels loaded with inplane shear

A modal flutter analysis for biaxially loaded, orthotropic panels, using linear piston-theory aerodynamics, was extended in order to include the effects of inplane shear loading. Flutter boundaries for shear loads up to buckling are calculated for simply supported, isotropic panels of various length-width ratios and for a square, isotropic panel with elastic boundary conditions along the leading and trailing edges. These flutter boundaries are used to define conservative design curves. Sample calculations made using these design curves indicate that practical panels, which have otherwise been adequately designed, could become flutter critical if the inplane shear loads approach the buckling value.

Sawyer, J. W.↗

NASA NTRS1975

The effect of circumferential distortion on fan performance at two levels of blade loading

Single stage fans designed for two levels of pressure ratio or blade loading were subjected to screen-induced circumferential distortions of 90-degree extent. Both fan rotors were designed for a blade tip speed of 425 m/sec, blade solidity of 1.3 and a hub-to-tip radius ratio of 0.5. Circumferential measurements of total pressure, temperature, static pressure, and flow angle were obtained at the hub, mean and tip radii at five axial stations. Rotor loading level did not appear to have a significant influence on rotor response to distorted flow. Losses in overall pressure ratio due to distortion were most severe in the stator hub region of the more highly loaded stage. At the near stall operating condition tip and hub regions of (either) rotor demonstrated different response characteristics to the distorted flow. No effect of loading was apparent on interactions between rotor and upstream distorted flow fields.

Hartmann, M. J.↗

NASA NTRS1975

A g-load display for remotely piloted vehicles and other aircraft that are subject to maneuvering constraints

The absence of kinesthetic cues deprives RPV pilots of essential feedback, particularly during high speed maneuvers. A display was designed to facilitate pilot control of g loads and to permit an immediate indication of g-load constraint violations. The display embodies all the motion vector components that contribute to maneuvering accelerations. In one mode of operation, the device displays the components of angular velocity as variable length pointers emanating from the center of a circle whose radius is determined by the linear velocity of the vehicle. An alternative mode of operation permits the pilot to select a display in which g loads are presented directly as variable length pointers emanating from the center of a circle whose radius is again determined by the linear velocity of the vehicle. Each circle defines a safe region of operation, and penetration of the circumference of the appropriate circle by a pointer implies that the structural design load was exceeded.

Howard, J. C.↗

NASA NTRS1975

Determination of rotor harmonic blade loads from acoustic measurements

The magnitude of discrete frequency sound radiated by a rotating blade is strongly influenced by the presence of a nonuniform distribution of aerodynamic forces over the rotor disk. An analytical development and experimental results are provided for a technique by which harmonic blade loads are derived from acoustic measurements. The technique relates, on a one-to-one basis, the discrete frequency sound harmonic amplitudes measured at a point on the axis of rotation to the blade-load harmonic amplitudes. This technique was applied to acoustic data from two helicopter types and from a series of test results using the NASA-Langley Research Center rotor test facility. The inferred blade-load harmonics for the cases considered tended to follow an inverse power law relationship with harmonic blade-load number. Empirical curve fits to the data showed the harmonic fall-off rate to be in the range of 6 to 9 db per octave of harmonic order. These empirical relationships were subsequently used as input data in a compatible far field rotational noise prediction model. A comparison between predicted and measured off-axis sound harmonic levels is provided for the experimental cases considered.

Kasper, P. K.↗

NASA NTRS1975

The effect of circumferential distortion on fan performance at two levels of blade loading

Single stage fans designed for two levels of pressure ratio or blade loading (rotor tip D-factor of 0.43 and 0.54) were subjected to screen-induced circumferential distortions of 90-degree extent. Both fan rotors were designed for a blade tip speed of 425 m/sec, blade solidity of 1.3 and a hub-to-tip radius ratio of 0.5. Circumferential measurements of total pressure, temperature, static pressure, and flow angle were obtained at the hub, mean and tip radii at five axial stations (three between the screen and rotor and behind rotor and stator blade rows). Rotor loading level did not appear to have a significant influence on rotor response to distorted flow. Losses in overall pressure ratio due to distortion were most severe in the stator hub region of the more highly loaded stage. At the near stall operating condition tip and hub regions of (either) rotor demonstrated different response characteristics to the distorted flow. No effect of loading was apparent on interactions between rotor and upstream distorted flow fields.

Hartmann, M. J.↗

NASA NTRS1975

Centaur Standard Shroud (CSS) static ultimate load structural tests

A series of tests were conducted on the jettisonable metallic shroud used on the Titan/Centaur launch vehicle to verify its structural capabilities and to evaluate its structural interaction with the Centaur stage. A flight configured shroud and the interfacing Titan/Centaur structural assemblies were subjected to tests consisting of combinations of applied axial and shear loads to design ultimate values, including a set of tests on thermal conditions and two dynamic response tests to verify the analytical stiffness model. The strength capabilities were demonstrated at ultimate (125 percent of design limit) loads. It was also verified that the spring rate of the flight configured shroud-to-Centaur forward structural deflections of the specimen became nonlinear, as expected, above limit load values. This test series qualification program verified that the Titan/Centaur shroud and the Centaur and Titan interface components are qualified structurally at design ultimate loads.

Source record↗

NASA NTRS1976

Preliminary weight and costs of sandwich panels to distribute concentrated loads

Minimum mass honeycomb sandwich panels were sized for transmitting a concentrated load to a uniform reaction through various distances. The form skin gages were fully stressed with a finite element computer code. The panel general stability was evaluated with a buckling computer code labeled STAGS-B. Two skin materials were considered; aluminum and graphite-epoxy. The core was constant thickness aluminum honeycomb. Various panel sizes and load levels were considered. The computer generated data were generalized to allow preliminary least mass panel designs for a wide range of panel sizes and load intensities. An assessment of panel fabrication cost was also conducted. Various comparisons between panel mass, panel size, panel loading, and panel cost are presented in both tabular and graphical form.

Belleman, G.↗

NASA NTRS1976

A computer program to predict rotor rotational noise of a stationary rotor from blade loading coefficient

The programing language used is FORTRAN IV. A description of all main and subprograms is provided so that any user possessing a FORTRAN compiler and random access capability can adapt the program to his facility. Rotor blade surface-pressure spectra can be used by the program to calculate: (1) blade station loading spectra, (2) chordwise and/or spanwise integrated blade-loading spectra, and (3) far-field rotational noise spectra. Any of five standard inline functions describing the chordwise distribution of the blade loading can be chosen in order to study parametrically the acoustic predictions. The program output consists of both printed and graphic descriptions of the blade-loading coefficient spectra and far-field acoustic spectrum. The results may also be written on binary file for future processing. Examples of the application of the program along with a description of the rotational noise prediction theory on which the program is based are also provided.

Ramakrishnan, R.↗

NASA NTRS1976

The effect of circumferential distortion on fan performance at two levels of blade loading

Single stage fans designed for two levels of pressure ratio or blade loading were subjected to screen induced circumferential distortions of 90 degree extent. Both fan rotors were designed for a blade tip speed of 425 m/sec, blade solidity of 1.3 and a hub-to-tip radius ratio of 0.5. Circumferential measurements of total pressure, temperature, static pressure, and flow angle were obtained at the hub, mean and tip radii at five axial stations. Rotor loading level did not appear to have a significant influence on rotor response to distorted flow. Losses in overall pressure ratio due to distortion were most severe in the stator hub region of the more highly loaded stage. At the near stall operating condition tip and hub regions of (either) rotor demonstrated different response characteristics to the distorted flow. No effect of loading was apparent on interactions between rotor and upstream distorted flow fields.

Hartmann, M. J.↗

NASA NTRS1976

Effect of loading and rotor wake characteristics on the acoustic field of stator blades

The generation of blade passing frequency noise due to rotor wakes interaction with the downstream stator is examined using a recent model for the unsteady aerodynamic forces developed by Goldstein and Atassi. The effects of blade geometry and loading are investigated. It is shown that at low reduced frequencies loading significantly reduces the noise level while at high frequencies loading substantially increases the sound level radiated. It is also shown that for the same loading a higher angle of attack generates more noise particularly at higher reduced frequencies. The noise level shows a quasi-periodic pattern with pronounced minima and maxima as the frequency increases. These conclusions are valid for different wake models.

Atassi, H.↗

NASA NTRS1976

Gaussian ideal impulsive loading of rigid viscoplastic plates

The response of a thin, rigid, viscoplastic plate subjected to a spatially axisymmetric Gaussian ideal impulse loading was studied analytically. The Gaussian ideal impulse distribution instantaneously imparts a Gaussian initial velocity distribution to the plate, except at the fixed boundary. The plate deforms with monotonically increasing deflections until the initial dynamic energy is completely dissipated in plastic work. The simply supported plate of uniform thickness obeys the von Mises yield criterion and a generalized constitutive equation for rigid, viscoplastic materials. For the small deflection bending response of the plate, neglecting the transverse shear stress in the yield condition and rotary inertia in the equations of dynamic equilibrium, the governing system of equations is essentially nonlinear. A proportional loading technique, known to give excellent approximations of the exact solution for the uniform load case, was used to linearize the problem and obtain analytical solution in the form of eigenvalue expansions. The linearized governing equations required the knowledge of the collapse load of the corresponding static problem.

Hayduk, R. J.↗

NASA NTRS1975

A 100-kW metal wind turbine blade basic data, loads and stress analysis

A rotor loads computer program was used to define the steady state and cyclic loads acting on 60 ft long metal blades designed for the ERDA/NASA 100 kW wind turbine. Blade load and stress analysis used to support the structural design are presented. For the loading conditions examined, the metal blades are structurally adequate for use, within the normal operating range, as part of the wind turbine system.

Cherritt, A. W.↗

NASA NTRS1977

Biaxial fatigue loading of notched composites

Thin walled, 2.54-cm (1-in.) diameter tubular specimens of T300/934 graphite/epoxy were fabricated and fatigue cycled in combinations of axial, torsional, and internal pressure loading. Two different four-ply layup configurations were tested: (0/90)S and (+ or - 45)S; all tubes contained a 0.48-cm (3/16-in.) diameter circular hole penetrating one wall midway along the tube length. S-N curves were developed to characterize fatigue behavior under pure axial, torsional, or internal pressure loading, as well as combined loading fatigue. A theory was developed based on the Hill plane stress model which enabled the S-N curve for combined stress states to be predicted from the S-N data for the uniaxial loading modes. Correlation of the theory with the experimental data proved to be remarkably good.

Francis, P. H.↗

NASA NTRS1978

Effects of rotor location, coning, and tilt on critical loads in large wind turbines

Several large (1500 kW) horizontal rotor configurations were analyzed to determine the effects on dynamic loads of upwind downwind rotor locations, coned and radial blade positions, and tilted and horizontal rotor axis positions. Loads were calculated for a range of wind velocities at three locations in the structure: (1) the blade shank; (2) the hub shaft; and (3) the yaw drive. Blade axis coning and rotor axis tilt were found to have minor effects on loads. However, locating the rotor upwind of the tower significantly reduced loads at all locations analyzed.

Spera, D. A.↗