Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Critical Fluids”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,603 records · Page 89
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Contact angle and surface tension measurements of a five-ring polyphenyl ether

Contact angle measurements were performed for a five-ring polyphenyl ether isomeric mixture on M-50 steel in a dry nitrogen atmosphere. Two different techniques were used: (1) a tilting plate apparatus, and (2) a sessile drop apparatus. Measurements were made for the temperature range 25 to 190 C. Surface tension was measured by a differential maximum bubble pressure technique over the range 23 to 220C in room air. The critical surface energy of spreading (gamma (sub c)) was determined for the polyphenyl ether by plotting the cosine of the contact angle (theta) versus the surface tension (gamma (sub LV)). The straight line intercept at cosine theta = 1 is defined as gamma (sub c). Gamma (sub c) was found to be 30.1 dyn/cm for the tilting plate technique and 31.3 dyn/cm for the sessile drop technique. These results indicate that the polyphenyl ether is inherently autophobic (i.e., it will not spread on its own surface film until its surface tension is less than gamma (sub c). This phenomenon is discussed in light of the wettability and wear problems encountered with this fluid.

Jones, W. R., Jr.↗
NASA NTRS1986

Contact angle and surface tension measurements of a five-ring polyphenyl ether

Contact angle measurements were performed for a five-ring polyphenyl ether isomeric mixture on M-50 steel in a dry nitrogen atmosphere. Two different techniques were used: (1) a tilting plate apparatus, and (2) a sessile drop apparatus. Measurements were made for the temperature range 25 to 190 C. Surface tension was measured by a differential maximum bubble pressure technique over the range 23 to 220 C in room air. The critical surface energy of spreading (gamma /sub c/) was determined for the polyphenyl ether by plotting the cosine of the contact angle (theta) versus the surface tension (gamma /sub LV/). The straight line intercept at cosine theta = 1 is defined as gamma (sub c). Gamma (sub c) was found to be 30.1 dyn/cm for the tilting plate technique and 31.3 dyn/cm for the sessile drop technique. These results indicate that the polyphenyl ether is inherently autophobic (i.e., it will not spread on its own surface film until its surface tension is less than gamma /sub c/). This phenomenon is discussed in light of the wettability and wear problems encountered with this fluid.

Jones, W. R., Jr.↗
NASA NTRS1991

Preparation of the Ice Certification of the Dornier 328 Regional Airliner By Numerical Simulation and By Ground Test

The Dornier 328, a new regional airliner, is to be qualified to FAR25/JAR25 requirements for operation into known icing conditions. All lifting surfaces are pneumatically deiced. Impingement limits were determined using a validated computational fluid dynamic (CFD) code. Wind tunnel tests with a model of the whole aircraft and the isolated empennage equipped with artificial ice shapes showed a degradation of handling characteristics due to ice accretion. Extensive two and three dimensional CFD calculations evaluated ice accretion at the deflection elevator horn. Icing tunnel tests were performed with a model of the horizontal tail with icing similitude fulfilled. The Dornier Do328 powerplant air induction system has successfully completed a program of icing tests in support of aircraft certification for operation into known icing conditions. Potential flight icing conditions were extensively analyzed using a CFD potential flow code and 3-D particle tracking routine to identify critical flight icing conditions. The tunnel test program verified the analytically predicted critical ice accretion surfaces of the air induction system, the adequacy of the ice protection provisions and demonstrated compliance with the applicable (JAR25) regulatory material.

D Welte↗
NASA NTRS2001

Volatility and Wear Characteristics of a Variety of Liquid Lubricants for Space Applications

The vapor pressures and wear characteristics are critical properties for liquid lubricants to assure long-term reliability and performance in space applications. Vapor pressures, obtained using a Knudsen cell technique, and wear properties, obtained using a vacuum four-ball apparatus, were measured for a series of unformulated liquid lubricants. These included two multiply alkylated cyclopentanes (MACs) (X-1000 and X2000), two linear perfluoropolyalkylethers (PFPAEs) (Z-25 and 815Z), and four silahydrocarbons (a tri, a tetra, and two pentas). Vapor pressures were measured at three elevated temperatures (423, 448, and 498 K) and extrapolated to room temperature 298 K. The lowest 298 K vapor pressure of 5.7 x 10(exp -14) Pa was obtained with the PFPAE fluid (815Z) and the highest value with the low molecular weight MAC (X-1000) at 3.6 x 10(exp -7) Pa. In addition, vacuum wear rates were determined for some of the lubricants. The lowest wear rates (approximately 3 x 10(exp -11) cubic mm/mm) were observed for three of the silahydrocarbons while the highest wear rates (approximately 2 x 10(exp -9) cubic mm/mm) were observed with the two PFPAE fluids (Z-25 and 815Z). The MAC (X-2000) yielded a wear rate of about 10(exp -10) cubic mm/mm. The results indicated that the silahydrocarbon class of liquid lubricants offers the better potential for space applications.

Nguyen, QuynhGiao N.↗
DOE OSTI2022

Tundra SGS – Critical Importance of Site-Specific Injectivity Testing for Carbon Dioxide Injection Well Simulation Calibration

Paper presented at 16th International Conference on Greenhouse Gas Control Technologies (GHGT-16), October 23–27, 2022, Lyon, France. Brine injectivity tests were conducted on both the Broom Creek (BC) and Deadwood (DW) storage formations in one of the cored stratigraphic test wells prior to finalized simulations. The injectivity tests entailed injection of brine into the formations, followed by shutting in the wells. The shut-in duration represents the fall-off period which was used to carry out pressure transient analyses of the tests. The analysis of injectivity tests indicated that core-indicated and modeled permeability distributions should be conservatively multiplied by 2.5× and 5× in the BC and DW geologic models, respectively, prior to numerical simulations of CO 2 injection using Computer Modelling Group’s (CMG’s) GEM equation-of-state reservoir simulator. The scaler permeability multipliers allowed the fluid flow simulations to fully represent well test-measured injection well rates in the respective formations.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2025

Performance of a dynamic single bubbler in single and two-phase immiscible liquids

Ensuring nonproliferation and safeguards of special nuclear materials (SNM) is a critical aspect of advancing the nuclear fuel cycle. Traditional bubbler systems used to estimate liquid levels and densities in nuclear recycling processes have limitations, particularly in harsh environments where dip-tube corrosion and buildup necessitate frequent maintenance and recalibration. This study explores the Dynamic Single Bubbler (DSB) method, which utilizes a single dip-tube attached to a linear actuator to estimate liquid properties dynamically. This approach is extended to estimate liquid-liquid interfaces in immiscible liquids and employs a linear regression method to reduce uncertainties and improve accuracy. The DSB method achieved density estimate uncertainties of less than 0.5% and surface level estimate uncertainties typically under 0.5%, across various fluids including water, acetone, methanol, mineral oil, glycerol, and aqueous salt solutions. Results indicate that the DSB method provides accurate and robust estimates of liquid density and surface levels with minimal maintenance and without the need for calibration. Additionally, the method's applicability to immiscible liquids and various dip-tube geometries was demonstrated, showing promise for widespread use in nuclear and other industrial applications.

98 - NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL↗
NASA NTRS2001

Volatility and Wear Characteristics of a Variety of Liquid Lubricants for Space Applications

The vapor pressures and near characteristics are critical properties for liquid lubricants to assure long-term reliability and performance in space applications. Vapor pressures, obtained using a Knudsen cell technique, and near properties, obtained using a vacuum four-ball apparatus, were measured for a series of unformulated liquid lubricants. These include: two multiple alkylated cyclopentanes (MACs) (X-1000 and X-2000), two linear perfluoropolyalkylethers (PFPAEs) (Z-25 and 815Z), and four silahydrocarbons (a tri-, a tetra-, and two pentas). Vapor pressures were measured at three elevated temperatures (423, 448, and 498 K) and extrapolated to room temperature 298 K. The lowest 298 K vapor pressure of 5.7 x 10(exp -14) Pa, was obtained with the PFPAE fluid (815Z) and the highest value with the low molecular weight MAC (X-1000) at 3.6 x 10(exp -7) Pa. In addition, vacuum near rates were determined for some of the lubricants. The lowest wear rates (approximately 3 x 10(exp -11) cubic mm/mm) were observed for three of the silahydrocarbons while the highest wear rate (approximately 2 x 10(exp-9) cubic mm/mm) were observed with the two PFPAE fluids (Z-25 and 815Z). The MAC (X-2000) yielded a wear rate of about 10(exp -10) cubic mm/mm. The results indicated that the silahydrocarbon class of liquid lubricants offers the better potential for space applications.

Nguyen, Quynhgiao N.↗
NASA NTRS2005

Technical Consultation of the International Space Station (ISS) Internal Active Thermal Control System (IATCS) Cooling Water Chemistry

The Internal Active Thermal Control System (IATCS) coolant exhibited unexpected chemical changes during the first year of on-orbit operation following the launch and activation in February 2001. The coolant pH dropped from 9.3 to below the minimum specification limit of 9.0, and re-equilibrated between 8.3 and 8.5. This drop in coolant pH was shown to be the result of permeation of CO2 from the cabin into the coolant via Teflon flexible hoses which created carbonic acid in the fluid. This unexpected diffusion was the result of having a cabin CO2 partial pressure higher than the ground partial pressure (average 4.0 mmHg vs. less than 0.2 mmHg). This drop in pH was followed by a concurrent increasing coolant nickel concentration. No other metal ions were observed in the coolant and based on previous tests, the source of nickel ion was thought to be the boron nickel (BNi) braze intermetallics used in the construction of HXs and cold plates. Specifically, BNi2 braze alloy was used for the IATCS IFHX and BNi3 braze alloy was used for the IATCS Airlock Servicing and Performance Checkout Unit (SPCU) HX and cold plates. Given the failure criticality of the HXs, a Corrosion Team was established by the IATCS CWG to determine the impact of the nickel corrosion on hardware performance life.

Gentz, Steven J.↗
DOE OSTI2022

Deformations, relaxation, and broken symmetries in liquids, solids, and glasses: A unified topological field theory

Here, we combine hydrodynamic and field theoretic methods to develop a general theory of phonons as Goldstone bosons in crystals, glasses, and liquids based on nonaffine displacements and the consequent Goldstone phase relaxation. We relate the conservation, or lack thereof, of specific higher-form currents with properties of the underlying deformation field—nonaffinity—which dictates how molecules move under an applied stress or deformation. In particular, the single-valuedness of the deformation field is associated with conservation of higher-form charges that count the number of topological defects. Our formalism predicts, from first principles, the presence of propagating shear waves above a critical wave vector in liquids, thus giving a formal derivation of the phenomenon in terms of fundamental symmetries. The same picture provides also a theoretical explanation of the corresponding “positive sound dispersion” phenomenon for longitudinal sound. Importantly, accordingly to our theory, the main collective relaxation timescale of a liquid or a glass (known as the α relaxation for the latter) is given by the phase relaxation time, which is not necessarily related to the Maxwell time. Finally, we build a nonequilibrium effective action using the in-in formalism defined on the Schwinger-Keldysh contour, that further supports the emerging picture. In summary, our work suggests that the fundamental difference between solids, fluids, and glasses has to be identified with the associated generalized higher-form global symmetries and their topological structure, and that the Burgers vector for the displacement fields serves as a suitable topological order parameter distinguishing the solid (ordered) phase and the amorphous ones (fluids, glasses).

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2025

Chemical Reactor Network Modeling of Ammonia Rich-Quench-Lean Combustion Using a Partially Stirred Reactor Approach

Ammonia is a promising alternative to hydrogen with high energy density and favorable storage and transport characteristics. However, low flammability and a propensity for high nitrogen oxide (NO x ) emissions make direct utilization challenging. Recently, two-stage rich-quench-lean (RQL) combustion strategies have shown promise in achieving low NO x emissions with ammonia. In this approach, the rich stage serves to oxidize a portion of the fuel while thermally decomposing as much of the remaining ammonia as possible, generating hydrogen. In the second (lean) stage, air is rapidly introduced, burning out the hydrogen and residual ammonia. Two-stage RQL combustion of ammonia has been investigated in the open literature both experimentally and numerically. In general, idealized chemical reactor network (CRN) models predict NO x concentrations below those of 2D/3D computational fluid dynamics models and experiments. The primary drivers of these discrepancies may be largely attributed to finite rate mixing nonadiabatic operation. The typical CRN model is comprised of a perfectly-stirred-reactor (PSR), followed by a plug-flow-reactor (PFR), meant to represent the flame, and postflame zones, respectively. In the two-stage RQL approach two PSR-PFR networks are arranged sequentially, corresponding to the rich and lean stages, with secondary air injection in between. In the authors' past work, this arrangement has demonstrated the significant sensitivity of exit NO x to the rich stage equivalence ratio, while the amount of secondary air injection was shown to be less critical. In this paper, the CRN model is extended to (1) include the impacts of heat loss and (2) utilize a partially-stirred-reactor (PaSR) approach to study the impacts of mixing on emissions performance. Varying amounts of heat loss are applied to the rich relaxation zone to understand emissions performance and changes to optimization of equivalence ratio and residence time. Premixed and nonpremixed configurations are considered in the rich stage PaSR, with varying degrees of mixing intensity to study the interaction between mixing, transport, and kinetic timescales. Critically, the impact of mixing between hot products and secondary air injection is studied to understand practical injector needs. Results show unburnt ammonia leaving the rich stage as a primary contributor to NO x emissions – driven both by increased heat loss and reduced mixing rates. Furthermore, heat losses have been shown to create conditions that are conducive to increased N 2 O formation in the lean stage. In conclusion, the results of this study will be considered in the context of developing optimized two-stage RQL combustors for ammonia.

Combustion↗
NASA NTRSDate not supplied

Evaluation of CFD as a Surrogate for Mach 2.4 to 4.6 Wind-Tunnel Testing – Project Overview

The debate over when wind-tunnel testing will be replaced by Computational Fluid Dynamics (CFD) comes and goes. More recently the debate has subsided with a more collaborative spirit between practitioners of these two disciplines resulting in significant improvements in the outcomes of both. There may come a time, however, when CFD has sufficient accuracy to supplant WTT as the dominant or perhaps only tool for aerodynamic simulation. If and/or when that happens, financial pressures favor efforts to close or severely limit the operations of wind tunnels. Presumably additional resources will go toward CFD to generate aerodynamic databases, load environments, and new aero/fluid-dynamic knowledge. It is therefore important to develop appropriate processes by which wind-tunnel closure decisions are made to ensure that facilities critical to industry and government research and development aren’t closed prematurely without proof that the available CFD tools have sufficient accuracy and low-enough cost (and enough experts and computational facilities) to take on the traditional role of wind tunnels. This paper will describe a project intended to answer the specific question of whether CFD can replace wind-tunnel testing for the limited Mach-number range 2.4 to 4.6. The project involves wind-tunnel testing and coordinated CFD for a variety of vehicle and flow-physics types in the high-speed leg of the Unitary Plan Wind Tunnel at NASA’s Langley Research Center.

James C Ross↗
DOE OSTI2023

Model assessment of synthetic jets for turbulent combustion experiments

Abstract Understanding turbulent premixed flames is essential to predict and optimize advanced combustion strategies, but critical capability gaps exist for collecting and validating measurements such as turbulent flame speed. Here, we evaluate synthetic jets as a new, promising turbulence generation device for constant-volume combustion chambers, quantitatively assessing turbulence intensity and spatial uniformity in a hypothetical 4,189-cm 3 vessel for various premixture conditions. Graphic Abstract

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2025

Unavoidable multilevel biaxial symmetry breaking in chiral hybrid liquid crystals

Chiral nematic or cholesteric liquid crystals (LCs) are fluid mesophases with long-ranged orientational order featuring a quasilayered periodicity imparted by a helical director configuration but lacking long-range positional order. Doping molecular cholesteric LCs with strongly anisotropic uniaxial colloidal particles adds another level of complexity because of the interplay between weak surface-anchoring boundary conditions and bulk-based elastic distortions near the particle-LC interface. Using cylindrical colloidal disks and rods with different geometric shapes and surface conditions, we demonstrate that these colloidal inclusions generically exhibit biaxial orientational probability distributions which may impart anomalously strong local biaxiality onto the hybrid cholesteric LC structure. Unlike nonchiral hybrid molecular-colloidal LCs, where biaxial order emerges only at critical colloid volume fractions exceeding some uniaxial-biaxial transition value, the orientational probability of the colloidal inclusions immersed in chiral nematic hosts is unambiguously biaxial even at infinite dilution. We demonstrate that the colloids induce local biaxial perturbations within the molecular orientational order of the LC host medium which strongly enhances the weak but native biaxial order of chiral nematic LC induced by the chiral symmetry breaking of the director field. With the help of analytical modeling and computer simulations based on the Landau–de Gennes free energy of the host LC around the colloids, we rationalize the observed multilevel biaxial order and conclude that it is not only unavoidable but also strongly enhanced compared to both achiral hybrid LCs and purely molecular cholesteric LCs.

biaxial liquid crystals↗
NASA NTRS2000

Aerothermodynamic Analysis of the Project FIRE II Afterbody Flow

35 years later, the Project FIRE II ballistic reentry to Earth at a nominal velocity of 11.4 km/s remains one of the best sources of heating data for the design of sample return capsules. The data from this flight experiment encompass both the thermochemical non-equilibrium and equilibrium flow regimes and include measurements of both radiative and total heating on the forebody and afterbody. Because of this, a number of researchers have performed computational fluid dynamics (CFD) simulations of the forebody of the FIRE II entry vehicle, with generally good results. In particular, Olynick et. al. coupled a Navier-Stokes solver (GIANTS) with a radiation code (NOVAR) and showed excellent agreement in surface heat transfer over the FIRE II trajectory between 1634 and 1651 seconds (77 km to 37 km). However, in most cases the primary motivation of the previous work was to understand and model the coupling between shock layer radiation and aerothermodynamics, and thus the simulations concentrated on the forebody flow only. To our knowledge there have been no prior published attempts to reproduce the afterbody heating data. However, an understanding of this data is critical to our efforts to design the next generation of Earth and planetary entry vehicles and to assess our need for additional flight data.

Wright, Micheal J.↗
NASA NTRSDate not supplied

Validation of Transient Spacecraft Refueling Model with Gateway Breadboard Test Data

The ability to refuel spacecraft on-orbit is a key enabling technology for deep space human exploration. On-orbit refueling requires priming a pressurized liquid propellant from a source tank into fluid transfer lines at vacuum conditions, which could result in excessive surge pressures beyond the system’s qualified operating limits and potentially damage hardware. Therefore, it is imperative to employ numerical models during the development of flight hardware to parametrically characterize system performance over a wide range of operating conditions. Since priming transients are difficult to model accurately, it is important to validate those models with test data. As part of the Gateway bipropellant refueling system development, a simplified fluidic breadboard system was created using water as a simulant for fuel to support early program risk reduction of refueling operations. The objectives of breadboard testing were to gather performance data to characterize and demonstrate critical refueling operations and to validate numerical models that can be extended to predicting flight system performance. A description of the breadboard test system and the results of numerical model validation is presented. The model is shown to have very good agreement with test data.

Brian S Lusby↗
NASA NTRS1997

An Experimental Study of Characteristic Combustion-Driven Flow for CFD Validation

A series of uni-element rocket injector studies were completed to provide benchmark quality data needed to validate computational fluid dynamic models. A shear coaxial injector geometry was selected as the primary injector for study using gaseous hydrogen/oxygen and gaseous hydrogen/liquid oxygen propellants. Emphasis was placed on the use of non-intrusive diagnostic techniques to characterize the flowfields inside an optically-accessible rocket chamber. Measurements of the velocity and species fields were obtained using laser velocimetry and Raman spectroscopy, respectively Qualitative flame shape information was also obtained using laser-induced fluorescence excited from OH radicals and laser light scattering studies of aluminum oxide particle seeded combusting flows. The gaseous hydrogen/liquid oxygen propellant studies for the shear coaxial injector focused on breakup mechanisms associated with the liquid oxygen jet under sub-critical pressure conditions. Laser sheet illumination techniques were used to visualize the core region of the jet and a Phase Doppler Particle Analyzer was utilized for drop velocity, size and size distribution characterization. The results of these studies indicated that the shear coaxial geometry configuration was a relatively poor injector in terms of mixing. The oxygen core was observed to extend well downstream of the injector and a significant fraction of the mixing occurred in the near nozzle region where measurements were not possible to obtain Detailed velocity and species measurements were obtained to allow CFD model validation and this set of benchmark data represents the most comprehensive data set available to date As an extension of the investigation, a series of gas/gas injector studies were conducted in support of the X-33 Reusable Launch Vehicle program. A Gas/Gas Injector Technology team was formed consisting of the Marshall Space Flight Center, the NASA Lewis Research Center, Rocketdyne and Penn State. Injector geometries studied under this task included shear and swirl coaxial configurations as well as an impinging jet injector.

Santoro, Robert J.↗
NASA NTRS2014

NASA Bioculture System: From Experiment Definition to Flight Payload

Starting in 2015, the NASA Bioculture System will be available to the science community to conduct cell biology and microbiology experiments on ISS. The Bioculture System carries ten environmentally independent Cassettes, which house the experiments. The closed loop fluids flow path subsystem in each Cassette provides a perfusion-based method for maintain specimen cultures in a shear-free environment by using a biochamber based on porous hollow fiber bioreactor technology. Each Cassette contains an incubator and separate insulated refrigerator compartment for storage of media, samples, nutrients and additives. The hardware is capable of fully automated or manual specimen culturing and processing, including in-flight experiment initiation, sampling and fixation, up to BSL-2 specimen culturing, and the ability to up to 10 independent cultures in parallel for statistical analysis. The incubation and culturing of specimens in the Bioculture System is a departure from standard laboratory culturing methods. Therefore, it is critical that the PI has an understanding the pre-flight test required for successfully using the Bioculture System to conduct an on-orbit experiment. Overall, the PI will conduct a series of ground tests to define flight experiment and on-orbit implementation requirements, verify biocompatibility, and determine base bioreactor conditions. The ground test processes for the utilization of the Bioculture System, from experiment selection to flight, will be reviewed. Also, pre-flight test schedules and use of COTS ground test equipment (CellMax and FiberCell systems) and the Bioculture System will be discussed.

Bioculture System↗
NASA NTRSDate not supplied

Reactor Parametric Assessments for Alternative Propellant Nuclear Thermal Propulsion Engines

This work focuses on the implications of alternative working fluids for nuclear thermal propulsion (NTP) reactors. To perform this analysis, NASA’s Testing Reference Design (TRD) is altered using parametric studies with selected alternative propellants to determine the reactor modifications required to enable an operable system. This research investigates ammonia, water, methane, helium, and enriched diborane as feasible options to enable a specific impulse (Isp) greater than the chemical propulsion alternatives. Frozen and dissociated Isp for each propellant is shown for variable chamber temperature conditions. Geometrical sensitivities are performed to observe the impact on the neutron multiplication factor (keff), system mass, and HALEU loading. Control drum worth curves are included for 5- degree increments of rotation. The base TRD configuration does not enable a critical system for ammonia and enriched diborane, thus these propellants will be highlighted in the final results. Equivalent study results for hydrogen will be included as a point of comparison to the performance of the other options.

Nuclear Thermal Propulsion↗