Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Contacts”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,603 records · Page 89
All sourcesNASA NTRSDOE OSTI
NASA NTRS2009

Non-Contact Measurement of Density and Thickness Variation in Dielectric Materials

This non-contact, single-sided terahertz electromagnetic measurement and imaging method characterizes micro structural (e.g., spatially-lateral density) and thickness variation in dielectric (insulating) materials. This method was demonstrated for space shuttle external tank sprayed-on foam insulation and has been designed for use as an inspection method for current and future NASA thermal protection systems and other dielectric material inspection applications where no contact can be made with the sample due to fragility and it is impractical to use ultrasonic methods

Roth, Ron↗
NASA NTRS2009

Use of Atomic Oxygen for Increased Water Contact Angles of Various Polymers for Biomedical Applications

The purpose of this study was to determine the effect of atomic oxygen (AO) exposure on the hydrophilicity of nine different polymers for biomedical applications. Atomic oxygen treatment can alter the chemistry and morphology of polymer surfaces, which may increase the adhesion and spreading of cells on Petri dishes and enhance implant growth. Therefore, nine different polymers were exposed to atomic oxygen and water-contact angle, or hydrophilicity, was measured after exposure. To determine whether hydrophilicity remains static after initial atomic oxygen exposure, or changes with higher fluence exposures, the contact angles between the polymer and water droplet placed on the polymer s surface were measured versus AO fluence. The polymers were exposed to atomic oxygen in a 100-W, 13.56-MHz radio frequency (RF) plasma asher, and the treatment was found to significantly alter the hydrophilicity of non-fluorinated polymers. Pristine samples were compared with samples that had been exposed to AO at various fluence levels. Minimum and maximum fluences for the ashing trials were set based on the effective AO erosion of a Kapton witness coupon in the asher. The time intervals for ashing were determined by finding the logarithmic values of the minimum and maximum fluences. The difference of these two values was divided by the desired number of intervals (ideally 10). The initial desired fluence was then multiplied by this result (2.37), as was each subsequent desired fluence. The flux in the asher was determined to be approximately 3.0 x 10(exp 15) atoms/sq cm/sec, and each polymer was exposed to a maximum fluence of 5.16 x 10(exp 20) atoms/sq cm.

deGroh, Kim↗
NASA NTRS2009

Preliminary Test Results of a Non-Contacting Finger Seal on a Herringbone-Grooved Rotor

The baseline non-contacting finger seal is a NASA patented design. The primary difference between it and Gul Aroras design patented by AlliedSignal is that there are no lift pads on the high pressure fingers. The baseline non-contacting finger seal is comprised of a back plate, aft spacer, aft (or low pressure) finger element, forward (or high pressure) finger element, forward spacer, and front plate. The components are held together with 20 flat head screws. A typical seal would have a back plate of approximately the same thickness as the front plate and would be riveted together. The thicker back plate allows use of threaded fasteners so that different finger elements can be tested without having to replace all the individual seal components. The finger elements are essentially washers made of thin sheet stock with multiple curved slots machined around the inner diameter to form the fingers. They are clocked so that the fingers of one cover the slots of the other. The aft finger element fingers have axial extensions or "lift pads" at the seal id that are concentric to the rotor. The fingers act as cantilever beams and flex in response to rotor dynamic motion and radial growth of the rotor due to centrifugal or thermal forces.

Proctor, Margaret P.↗
NASA NTRS2006

Better Back Contacts for Solar Cells on Flexible Substrates

Improved low-resistance, semitransparent back contacts, and a method of fabricating them, have been developed for solar photovoltaic cells that are made from thin films of I-III-VI2 semiconductor materials on flexible, high-temperatureresistant polyimide substrates or superstrates. The innovative aspect of the present development lies in the extension, to polyimide substrates or superstrates, of a similar prior development of improved low-resistance, semitransparent back contacts for I-III-VI2 solar cells on glass substrates or superstrates. A cell incorporating this innovation can be used either as a stand-alone photovoltaic device or as part of a monolithic stack containing another photovoltaic device that utilizes light of longer wavelengths.

Woods, Lawrence M.↗
NASA NTRS2011

Mesh-Based Entry Vehicle and Explosive Debris Re-Contact Probability Modeling

The risk to a crewed vehicle arising from potential re-contact with fragments from an explosive breakup of any jettisoned spacecraft segments during entry has long sought to be quantified. However, great difficulty lies in efficiently capturing the potential locations of each fragment and their collective threat to the vehicle. The method presented in this paper addresses this problem by using a stochastic approach that discretizes simulated debris pieces into volumetric cells, and then assesses strike probabilities accordingly. Combining spatial debris density and relative velocity between the debris and the entry vehicle, the strike probability can be calculated from the integral of the debris flux inside each cell over time. Using this technique it is possible to assess the risk to an entry vehicle along an entire trajectory as it separates from the jettisoned segment. By decoupling the fragment trajectories from that of the entry vehicle, multiple potential separation maneuvers can then be evaluated rapidly to provide an assessment of the best strategy to mitigate the re-contact risk.

McPherson, Mark A.↗
NASA NTRS2012

Non-Contact Conductivity Measurement for Automated Sample Processing Systems

A new method has been developed for monitoring and control of automated sample processing and preparation especially focusing on desalting of samples before analytical analysis (described in more detail in Automated Desalting Apparatus, (NPO-45428), NASA Tech Briefs, Vol. 34, No. 8 (August 2010), page 44). The use of non-contact conductivity probes, one at the inlet and one at the outlet of the solid phase sample preparation media, allows monitoring of the process, and acts as a trigger for the start of the next step in the sequence (see figure). At each step of the muti-step process, the system is flushed with low-conductivity water, which sets the system back to an overall low-conductivity state. This measurement then triggers the next stage of sample processing protocols, and greatly minimizes use of consumables. In the case of amino acid sample preparation for desalting, the conductivity measurement will define three key conditions for the sample preparation process. First, when the system is neutralized (low conductivity, by washing with excess de-ionized water); second, when the system is acidified, by washing with a strong acid (high conductivity); and third, when the system is at a basic condition of high pH (high conductivity). Taken together, this non-contact conductivity measurement for monitoring sample preparation will not only facilitate automation of the sample preparation and processing, but will also act as a way to optimize the operational time and use of consumables

Beegle, Luther W.↗
NASA NTRS2015

Fast Grasp Contact Computation for a Serial Robot

A system includes a controller and a serial robot having links that are interconnected by a joint, wherein the robot can grasp a three-dimensional (3D) object in response to a commanded grasp pose. The controller receives input information, including the commanded grasp pose, a first set of information describing the kinematics of the robot, and a second set of information describing the position of the object to be grasped. The controller also calculates, in a two-dimensional (2D) plane, a set of contact points between the serial robot and a surface of the 3D object needed for the serial robot to achieve the commanded grasp pose. A required joint angle is then calculated in the 2D plane between the pair of links using the set of contact points. A control action is then executed with respect to the motion of the serial robot using the required joint angle.

Shi, Jianying↗
NASA NTRS2015

Non-Contact Thermal Characterization of NASA's HERMeS Hall Thruster

The Thermal Characterization Test of NASAs 12.5-kW Hall thruster is being completed. This thruster is being developed to support of a number of potential Solar Electric Propulsion Technology Demonstration Mission concepts, including the Asteroid Redirect Robotic Mission concept. As a part of this test, an infrared-based, non-contact thermal imaging system was developed to measure Hall thruster surfaces that are exposed to high voltage or harsh environment. To increase the accuracy of the measurement, a calibration array was implemented, and a pilot test was performed to determine key design parameters for the calibration array. The raw data is analyzed in conjunction with a simplified thermal model of the channel to account for reflection. The reduced data will be used to refine the thruster thermal model, which is critical to the verification of the thruster thermal specifications. The present paper will give an overview of the decision process that led to identification of the need for a non-contact temperature diagnostic, the development of said diagnostic, the measurement results, and the simplified thermal model of the channel.

Electric Propulsion↗
NASA NTRS2016

Non-Contacting Finger Seals Static Performance Test Results at Ambient and High Temperatures

The non-contacting finger seal is an advanced seal concept with potential to reduce specific fuel consumption in gas turbine engines by 2 to 3 percent with little to no wear of the seal or rotor. Static performance tests and bind-up tests of eight different non-contacting finger seal configurations were conducted in air at pressure differentials up to 689.4 kPa and temperatures up to 922 K. Four of the seals tested were designed to have lift pads concentric to a herringbone-grooved rotor which generates hydrodynamic lift when rotating. The remaining seals were tested with a smooth rotor; one seal had a circumferential taper and one had an axial taper on the lift pad inner diameter to create hydrodynamic lift during rotation. The effects of the aft finger axial thickness and of the forward finger inner diameter on leakage performance were investigated as well and compared to analytical predictions.

static tests↗
NASA NTRS2016

Non-Contacting Finger Seals Static Performance Test Results at Ambient and High Temperatures

The non-contacting finger seal is an advanced seal concept with potential to reduce specific fuel consumption in gas turbine engines by 2 to 3 with little to no wear of the seal or rotor. Static performance tests and bind-up tests of eight different non-contacting finger seal configurations were conducted in air at pressure differentials up to 689.4 kPa and temperatures up to 922 K. Four of the seals tested were designed to have lift pads concentric to a herringbone-grooved rotor which generates hydrodynamic lift when rotating. The remaining seals were tested with a smooth rotor; one seal had a circumferential taper and one had an axial taper on the lift pad inner diameter to create hydrodynamic lift during rotation. The effects of the aft finger axial thickness and of the forward finger inner diameter on leakage performance were investigated as well and compared to analytical predictions.

rotors↗
NASA NTRS2018

Comparison of Performance Test Results to CFD and Structural Models of Non-Contacting Finger Seals

Performance tests of non-contacting finger seal designs were conducted at 300, 700, 922 K (70, 800 and 1200 F) at pressure differentials up to 517 kPa (75 psid) and surface speeds up to 366 m/s (1200 ft/s). Room temperature, static analysis of the seal was performed. A simplified CFD model was developed to examine pressure loads within the seal. Results from the CFD model were used as input to a finite element analysis model of a six-finger segment of the non-contacting finger seal. Examination of predicted deflections of individual components of the seal gives insight into the seal behavior. Wear patterns from testing verify the pattern of radial deflection. The models are used to predict maximum pressure differential capability of the seal and compared to experimental results. The CFD model slightly under-predicts the measured leakage flow factor, but has the same trend as the measured flow factor versus pressure differential.

Seals:Brush Seals↗
NASA NTRS2019

An Analytic Model for Estimating the First Contact Resistance Needed to Avoid Damaging ESD During Spacecraft Docking in GEO

NASA’s Gateway program will involve spacecraft (s/c) docking in the outer radiation belt in order to transfer Gateway elements between s/c for transport to lunar orbit. The charging of these s/c to different potentials prior to docking raises the possibility of a damaging electrostatic discharge (ESD) at the time of first contact between the s/c. A proposed mitigation strategy is for first contact to occur prior to docking through a resistor with resistance R that would lower the potential difference at an optimal rate to a sufficiently low value to prevent ESD damage. The coupling of s/c by a resistor can be modeled by SPIS, but for realistic two s/c models SPIS can take hours to simulate the evolution of the s/c surface charges and potentials to an equilibrium state. Our objective is to develop a simpler model of s/c resistive coupling that runs orders of magnitude faster while providing useful first design estimates of the time variation of the s/c potentials, current through the resistor, and how these vary with R and s/c configuration This configuration is defined by the relative separation and orientation of the s/c, and their solar illumination. The configuration and geometry of the s/c determine their capacitive coupling. The s/c capacitances are computed using Nascap-2K. This poster presents the first version of such a model, and initial tests.

Goodman, Michael L.↗
NASA NTRS2019

An Analytic Model for Estimating the First Contact Resistance Needed to Avoid Damaging ESD During Spacecraft Docking in GEO

NASA’s Gateway program is to involve spacecraft (s/c) docking in the outer radiation belt in order to transfer Gateway elements between s/c for transport to lunar orbit. The charging of these s/c to different potentials prior to docking raises the possibility of a damaging electrostatic discharge (ESD) at the time of first contact between the s/c. A proposed mitigation strategy is for first contact to occur prior to docking through a resistor with resistance R that would lower the potential difference at an optimal rate to a sufficiently low value to prevent a damaging ESD. The coupling of s/c by a resistor can be modeled by SPIS (Spacecraft Plasma Interaction System), but for realistic two s/c models SPIS can take hours to simulate the evolution of the s/c surface charges and potentials to an equilibrium state. Our objective is to develop a simpler model of s/c resistive coupling that runs orders of magnitude faster while providing useful first design estimates of the time variation of the s/c potentials, current through the resistor, and how these vary with R and s/c configuration. This configuration is defined by the relative separation and orientation of the s/c, and their solar illumination. The configuration and geometry of the s/c determine their capacitive coupling. The s/c capacitances are computed using Nascap-2K. This abstract and the associated poster describe the first version of such a model, and initial tests.

Goodman, Michael L.↗
NASA NTRS2019

Lamb wave defect detection and evaluation using a fully non-contact laser system

Traditional Lamb wave structural health monitoring (SHM)/nondestructive evaluation (NDE) system employs contact type transducers such as PZT, ultrasonic transducers, and optical fibers. In application, transducer attachment and maintenance can be time and labor consuming. In addition, the use of couplant and adhesives can introduce additional materials on structures, and the interface coupling is often not well understood. To overcome these limitations, we proposed a fully non-contact NDE system by employing pulsed laser (PL) for Lamb wave actuation and scanning laser Doppler vibrometer (SLDV) for Lamb wave sensing. The proposed system is implemented on aluminum plates. The PL Lamb wave excitation is calibrated, and the optimal parameters are obtained. Lamb wave modes are then characterized through 1D wavefield analysis. With the calibrated and characterized system, defect detection and evaluation are achieved on aluminum plates with simulated defects (surfaced-bonded quartz rod, and machine milled crack) through 1D and 2D inspection in both time-space and frequency-wavenumber domains.

Ma, Zhaoyun↗
NASA NTRS2019

On-Demand Non-Contact Distillation: Low-g Demonstrations of a Leidenfrost Waste-Water Processor

Leidenfrost phenomenon is employed as a potential solution to NASA’s urine water recovery problem by providing a method for on demand non-contact distillation. Leidenfrost investigations have been almost exclusively conducted in terrestrial environments and are in turn largely defined by the ever-presence of gravity. In this work we demonstrate a variety of Leidenfrost effects for enormous liquid droplets in the microgravity environment of a 2.1 second drop tower. Dynamic Leidenfrost droplet impacts on a selection of heated hydrophilic and superhydrophobic surfaces in microgravity are presented. Nearly ideal elastic non- contact impacts and droplet oscillation modes are observed. Impact experiments are extended to a variety of heated substrates including macro pillar arrays, confined passageways, and others. The potential for contamination-free processing is obvious, with the proof of concept to be pursued shortly.

Leidenfrost↗
NASA NTRSDate not supplied

Metal Contact Processing Experiments Towards Realizing 500 °C Durable RF 4H-SiC BJTs

This paper presents results from metal contact processing experiments towards the implementationof durable 500 deg.C high-frequency 4H-SiC bipolar junction transistors (BJTs). Specifically, p-type ohmic contacts have been demonstrated on a 0.25 μm-thick p-type homoepitaxial layer of doping 8 x 1018± 4 x 1018cm-3. Finally, preliminary current-voltage characteristics of fabricated BJTs are presented.

RF SiC↗
NASA NTRS2023

Metal Contact Processing Experiments Towards Realizing 500 °C Durable RF 4H-SiC BJTs

This paper presents results from metal contact processing experiments towards the implementation of durable 500 °C high-frequency 4H-SiC bipolar junction transistors (BJTs) . Specifically, p -type ohmic contacts have been demonstrated on a 0.25 μm-thick p -type homoepitaxial layer of doping 8 x 10 18 ± 4 x 10 18 cm -3 . Preliminary current-voltage characteristics of fabricated BJTs are presented.

4H-SiC BJT↗