Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Compression”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,603 records · Page 89

Design of a very-low-bleed Mach 2.5 mixed-compression inlet with 45 percent internal contraction

A full-scale, mixed-compression inlet was designed for operation with the TF30-P-3 turbofan engine and tested at Mach numbers of 2.5 and 2.0. The two-cone axisymmetric inlet had minimum internal contraction consistent with high total pressure recovery and low cowl drag. At Mach 2.5, inlet recovery was 0.906 with only 0.021 centerbody bleed mass-flow ratio and no cowl bleed. Increased centerbody bleed gave a maximum inlet unstart angle of attack of 6.85 deg. At Mach 2.0, inlet recovery was 0.94 with only 0.014 centerbody bleed mass-flow ratio and no cowl bleed. Inlet performance and angle-of-attack tolerance is presented for operation at Mach numbers of 2.5 and 2.0.

Wasserbauer, J. F.↗

Effect of afterburner lights and inlet unstarts on a mixed compression inlet turbofan engine operating at Mach 2.5

Data are presented to show the response of an uncontrolled inlet to afterburner lightoff disturbances when a mixed-compression inlet is coupled to a turbofan engine. The results show a significant upstream shock excursion when the afterburner lights which is a result of the direct communication between the afterburner region and the inlet by means of the fan duct and fan stages. In addition results of a waveform analysis on the inlet pressure response to the afterburner light is presented. Inlet unstarts and their effect on operation of the propulsion system is also discussed.

Baumbick, R. J.↗

Design of a digital voice data compression technique for orbiter voice channels

Candidate techniques were investigated for digital voice compression to a transmission rate of 8 kbps. Good voice quality, speaker recognition, and robustness in the presence of error bursts were considered. The technique of delayed-decision adaptive predictive coding is described and compared with conventional adaptive predictive coding. Results include a set of experimental simulations recorded on analog tape. The two FM broadcast segments produced show the delayed-decision technique to be virtually undegraded or minimally degraded at .001 and .01 Viterbi decoder bit error rates. Preliminary estimates of the hardware complexity of this technique indicate potential for implementation in space shuttle orbiters.

Source record↗

Study of efficient video compression algorithms for space shuttle applications

Results are presented of a study on video data compression techniques applicable to space flight communication. This study is directed towards monochrome (black and white) picture communication with special emphasis on feasibility of hardware implementation. The primary factors for such a communication system in space flight application are: picture quality, system reliability, power comsumption, and hardware weight. In terms of hardware implementation, these are directly related to hardware complexity, effectiveness of the hardware algorithm, immunity of the source code to channel noise, and data transmission rate (or transmission bandwidth). A system is recommended, and its hardware requirement summarized. Simulations of the study were performed on the improved LIM video controller which is computer-controlled by the META-4 CPU.

Poo, Z.↗

The design of a digital voice data compression technique for orbiter voice channels

Voice bandwidth compression techniques were investigated to anticipate link margin difficulties in the shuttle S-band communication system. It was felt that by reducing the data rate on each voice channel from the baseline 24 (or 32) Kbps to 8 Kbps, additional margin could be obtained. The feasibility of such an alternate voice transmission system was studied. Several factors of prime importance that were addressed are: (1) achieving high quality voice at 8 Kbps; (2) performance in the presence of the anticipated shuttle cabin environmental noise; (3) performance in the presence of the anticipated channel error statistics; and (4) minimal increase in size, weight, and power over the current baseline voice processor.

Source record↗

Vapor compression distillation module

A Vapor Compression Distillation (VCD) module was developed and evaluated as part of a Space Station Prototype (SSP) environmental control and life support system. The VCD module includes the waste tankage, pumps, post-treatment cells, automatic controls and fault detection instrumentation. Development problems were encountered with two components: the liquid pumps, and the waste tank and quantity gauge. Peristaltic pumps were selected instead of gear pumps, and a sub-program of materials and design optimization was undertaken leading to a projected life greater than 10,000 hours of continuous operation. A bladder tank was designed and built to contain the waste liquids and deliver it to the processor. A detrimental pressure pattern imposed upon the bladder by a force-operated quantity gauge was corrected by rearranging the force application, and design goals were achieved. System testing has demonstrated that all performance goals have been fulfilled.

Nuccio, P. P.↗

Control of shock wave-boundary layer interactions by bleed in supersonic mixed compression inlets

An experimental investigation was conducted to determine the effect of bleed on a shock wave-boundary layer interaction in an axisymmetric mixed-compression supersonic inlet. The inlet was designed for a free-stream Mach number of 2.50 with 60-percent supersonic internal area contraction. The experiment was conducted in the NASA Lewis Research Center 10-Foot Supersonic Wind Tunnel. The effects of bleed amount and bleed geometry on the boundary layer after a shock wave-boundary layer interaction were studied. The effect of bleed on the transformed form factor is such that the full realizable reduction is obtained by bleeding of a mass flow equal to about one-half of the incident boundary layer mass flow. More bleeding does not yield further reduction. Bleeding upstream or downstream of the shock-induced pressure rise is preferable to bleeding across the shock-induced pressure rise.

Fukuda, M. K.↗

Variable geometry for supersonic mixed-compression inlets

Study of two-dimensional and axisymmetric supersonic mixed-compression inlet systems has shown that the geometry of both systems can be varied to provide adequate transonic airflow to satisfy the airflow demand of most jet engines. Collapsing geometry systems for both types of inlet systems provide a generous amount of transonic airflow for any design Mach number inlet system. However, the mechanical practicality of collapsing centerbodies for axisymmetric inlet systems is doubtful. Therefore, translating centerbody axisymmetric inlets with auxiliary airflow systems to augment the transonic airflow capability are an attractive alternative. Estimates show that the capture mass-flow ratio at Mach number 1.0 can be increased approximately 0.20 for a very short axisymmetric inlet system designed for Mach number 2.37. With this increase in mass-flow ratio, even variable-cycle engine transonic airflow demand can be matched without oversizing the inlet at the design Mach number.

Sorensen, N. E.↗

Numerical solutions of supersonic and hypersonic laminar flows over a two-dimensional compression corner

An efficient time-splitting, second-order accurate, numerical scheme is used to solve the complete Navier-Stokes equations for supersonic and hypersonic laminar flow over a two-dimensional compression corner. A fine, exponentially stretched mesh spacing is used in the region near the wall for resolving the viscous layer. Good agreement is obtained between the present computed results and experimental measurement for a Mach number of 14.1, a Reynolds number of 104,000, and wedge angles of 15, 18, and 24 deg. The details of the pressure variation across the boundary layer are given, and a correlation between the leading edge shock and the peaks in surface pressure and heat transfer is observed.

Hung, C. M.↗

The problem of a finite strip compressed between two rough rigid stamps

A finite strip compressed between two rough rigid stamps is considered. The elastostatic problem is formulated in terms of a singular integral equation from which the proper stress singularities at the corners are determined. The singular integral equation is solved numerically to determine the stresses along the fixed ends of the strip. The effect of material properties and strip geometry on the stress-intensity factor is presented graphically.

Gupta, G. D.↗

Evaluation of boron/aluminum tubes in compression

A brief analytical and experimental investigation was conducted to determine the compressive behavior of a limited number of boron/aluminum (B/Al) tubes. The purpose of the investigation was to gain hardware experience in a limited evaluation of the material for possible application to spacecraft truss structures. Specimen description, test procedures and results are presented as well as comparisons with theoretical predictions regarding local column stability. It is shown that the experimental results of full-scale tests are consistent with previously reported data and that the local stability of B/Al columns as determined through short column tests can best be predicted using large deflection theory.

Knoell, A. C.↗

Behavior of some singly ionized, heavy-ion impurities during compression in a theta-pinch plasma

The introduction of a small percentage of an impurity gas containing a desired element into a theta-pinch plasma is a standard procedure used to investigate the spectra and atomic processes of the element. This procedure assumes that the mixing ratio of impurity-to-fill gases remains constant during the collapse and heating phase. Spectroscopic investigations of the constant-mixing-ratio assumption for a 2% neon and argon impurity verifies the assumption only for the neon impurity. However, for the 2% argon impurity, only 20 to 25% of the argon is in the high-temperature compressed plasma. It is concluded that the constant-mixing-ratio assumption is not applicable to the argon impurity.

Jalufka, N. W.↗

Control of shock-wave boundary-layer interactions by bleed in supersonic mixed compression inlets

An experimental investigation has been conducted to determine the effect of bleed region geometry and bleed rate on shock wave-boundary layer interactions in an axisymmetric, mixed-compression inlet at a Mach number of 2.5. The full realizable reduction in transformed form factor is obtained by bleeding off about half the incident boundary layer mass flow. Bleeding upstream or downstream of the shock-induced pressure rise is preferable to bleeding across the shock-induced pressure rise. Slanted holes are more effective than normal holes. Two different bleed hole sizes were tested without detectable difference in performance.

Fukuda, M. K.↗

An investigation of several numerical procedures for time-asymptotic compressible Navier-Stokes solutions

The status of an investigation of four numerical techniques for the time-dependent compressible Navier-Stokes equations is presented. Results for free shear layer calculations in the Reynolds number range from 1000 to 81000 indicate that a sequential alternating-direction implicit (ADI) finite-difference procedure requires longer computing times to reach steady state than a low-storage hopscotch finite-difference procedure. A finite-element method with cubic approximating functions was found to require excessive computer storage and computation times. A fourth method, an alternating-direction cubic spline technique which is still being tested, is also described.

Rudy, D. H.↗

Compressed air demand-type firefighter's breathing system, volume 1

The commercial availability of lightweight high pressure compressed air vessels has resulted in a lightweight firefighter's breathing apparatus. The improved apparatus, and details of its design and development are described. The apparatus includes a compact harness assembly, a backplate mounted pressure reducer assembly, a lightweight bubble-type facemask with a mask mounted demand breathing regulator. Incorporated in the breathing regulator is exhalation valve, a purge valve and a whistle-type low pressure warning that sounds only during inhalation. The pressure reducer assembly includes two pressure reducers, an automatic transfer valve and a signaling device for the low pressure warning. Twenty systems were fabricated, tested, refined through an alternating development and test sequence, and extensively examined in a field evaluation program. Photographs of the apparatus are included.

Sullivan, J. L.↗

The compressibility rule for drag of airfoil noses

It is shown that the drag of any semi-infinite airfoil section in purely subsonic inviscid flow follows precisely the Prandtl-Glauert compressibility rule. The result for the parabola has application to leading edge corrections in thin airfoil theory.

Jones, R. T.↗