Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Capacitors”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,603 records · Page 89

Deposition Of Materials Using A Simple Planar Coil Radio Frequency Inductively Coupled Plasma System

A planar coil RF inductively coupled plasma (PC-RFICP) systems is set up for the purpose of thin film deposition. The system is powered by a 13.56 MHz, 550 W, 50 OMEGA RF generator. The RF power is transferred to the plasma via a planar induction coil. The impedance matching unit consists of an air core step-down transformer and a tunable vacuum capacitor. This system is used for the plasma enhanced chemical vapor deposition (PECVD) of diamond-like carbon (DLC) film on silicon substrate, and hydrogenated amorphous carbon (a-C:H) film.

36 MATERIALS SCIENCE↗

KSI's Cross Insulated Core Transformer Technology

Cross Insulated Core Transformer (CCT) technology improves on Insulated Core Transformer (ICT) implementations. ICT systems are widely used in very high voltage, high power, power supply systems. In an ICT transformer ferrite core sections are insulated from their neighboring ferrite cores. Flux leakage is present at each of these insulated gaps. The flux loss is raised to the power of stages in the ICT design causing output voltage efficiency to taper off with increasing stages. KSI's CCT technology utilizes a patented technique to compensate the flux loss at each stage of an ICT system. Design equations to calculate the flux compensation capacitor value are presented. CCT provides corona free operation of the HV stack. KSI's CCT based High Voltage power supply systems offer high efficiency operation, high frequency switching, low stored energy and smaller size over comparable ICT systems.

43 PARTICLE ACCELERATORS↗

Neutron yield saturation in plasma focus: A fundamental cause

Plasma focus research in the direction of fusion energy faces the limitation of observed neutron saturation; the neutron yield Y{sub n} falls away from Y{sub n}{approx}E{sub 0}{sup 2}, the scaling deteriorating as storage energy E{sub 0} increases toward 1 MJ. Numerical experiments confirm that Y{sub n}{approx}E{sub 0}{sup 2} applies at low energies and drops to Y{sub n}{approx}E{sub 0}{sup 0.8} toward 25 MJ; deteriorating already at several hundred kilojoules. We point out that the cause is the dynamic resistance of the axial phase that is constant for all plasma foci. This dynamic resistance dominates the circuit as capacitor bank surge impedance becomes insignificant at large E{sub 0}, causing current, hence neutron 'saturation'.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Conduction mechanism of sputtered BaTiO{sub 3} film on Ni substrate

BaTiO{sub 3} (BTO) thin film capacitors were deposited on Ni substrate using rf magnetron sputtering. Microstructural studies by x-ray diffraction and transmission electron microscopy reveal that the as-grown BTO films have the columnar structure and the good interface structure. Postdeposition anneal results in the recrystallization of BTO films. The electrical measurements exhibit that the BTO films have high capacitance densities and low leakage currents.

36 MATERIALS SCIENCE↗

Effect of the resonant growth of harmonics on the electron density in capacitively coupled plasma

The growth of harmonics is known to occur under the condition of plasma series resonance (PSR). In an actual plasma process chamber, the external circuit also affects the PSR. We experimentally demonstrated the resonant growth of the third and fourth harmonics by tuning a variable capacitor attached to the electrode, and investigated the influence of the growth on the electron density. We observed significant increases in electron density as the amplitude of harmonics grows. The result clearly shows that nonlinear electron resonance heating actually takes place.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Epitaxial growth of (001)-oriented Ba{sub 0.5}Sr{sub 0.5}TiO{sub 3} thin films on a-plane sapphire with an MgO/ZnO bridge layer

High quality (001)-oriented Ba{sub 0.5}Sr{sub 0.5}TiO{sub 3} (BST) thin films have been grown on a-plane sapphire (1120) by rf magnetron sputtering using a double bridge layer consisting of (0001)-oriented ZnO (50 nm) and (001)-oriented MgO (10 nm) prepared by plasma-assisted molecular beam epitaxy. X-ray diffraction revealed the formation of three sets of in-plane BST domains, offset from one another by 30 deg., which is consistent with the in-plane symmetry of the MgO layer observed by in situ reflective high electron energy diffraction. The in-plane epitaxial relationship of BST, MgO, and ZnO has been determined to be BST [110]//MgO [110]//ZnO [1120] and BST [110]/MgO [110]//ZnO [1100]. Capacitance-voltage measurements performed on BST coplanar interdigitated capacitor structures revealed a high dielectric tunability of up to 84% at 1 MHz.

36 MATERIALS SCIENCE↗

An innovative high-power constant-current pulsed-arc power-supply for a high-density pulsed-arc-plasma ion-source using a LaB{sub 6}-filament

An innovative high-power constant-current (CC) pulsed-arc (PA) power-supply (PS) indispensable for a high-density PA plasma ion-source using a lanthanum hexaboride (LaB{sub 6}) filament was devised by combining a constant-voltage (CV) PA-PS, which is composed of an insulated gate bipolar transistor (IGBT) switch, a CV direct-current (dc) PS and a 270 mF capacitor with a CC-PA-PS, which is composed of an IGBT-switch, a CC-dc-PS and a 400 {mu}H inductor, through the inductor. The hybrid-CC-PA-PS succeeded in producing a flat arc-pulse with a peak power of 56 kW (400 Ax140 V) and a duty factor of more than 1.5%(600 {mu}sx25 Hz) for Japan Proton Accelerator Research Complex (J-PARC) H{sup -} ion-source stably. It also succeeded in shortening the 99% rising-time of the arc-pulse-current to about 20 {mu}s and tilting up or down the arc-pulse-current arbitrarily and almost linearly by changing the setting voltage of its CV-dc-PS.

43 PARTICLE ACCELERATORS↗

Synthesis, structure, and electrical behavior of Sr{sub 4}Bi{sub 4}Ti{sub 7}O{sub 24}.

An n = 7 Aurivillius phase, Sr{sub 4}Bi{sub 4}Ti{sub 7}O{sub 24}, with c = 6.44 nm, was synthesized as an epitaxial (001)-oriented film. This phase and its purity were confirmed by x-ray diffraction and transmission electron microscopy. The material is ferroelectric, with a P{sub r} = 5.3 {micro}C/cm{sup 2} oriented in the (001) plane and a paraelectric-to-ferroelectric transition temperature of T{sub C} = 324 K. Some indications of relaxorlike behavior are observed. Such behavior is out of character for Sr{sub n-1}Bi{sub 2}Ti{sub n}O{sub 3n+3} Aurivillius phases and is closer to the bulk behavior of doped SrTiO{sub 3}, implying a spatial limit to the elastic interlayer interactions in these layered oxides. A finite-element solution to the interpretation of data from interdigitated capacitors on thin films is also described.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Analysis of the ITER ICRH Decoupling and Matching System

The reference ITER ICRH load resilient matching system uses four 3dB hybrid power splitters. It is proposed to use a 'double stub' tuner (DST) configuration for the matching on the reference load and a decoupling system placed between the antenna plug and the matching system to reduce the mutual coupling effects and also to actively control the array current spectrum while requesting the same forward power from all 4 power sources. The paper analyzes (i) the optimization of the matching layout e.g. by varying the distance between the stubs and by the use of two capacitors taking into account the role of the decouplers on the matching requirements; (ii) the practical realization of the decouplers and their insertion into the circuit; (iii) the requests in voltage and current capabilities in the different parts of the system. The paper presents solutions for saving space and to decrease the ratings of the components. The computations are done with the array loading simulated by the TOPICA matrix.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

A Fast Pulse, High Intensity Neutron Source Based Upon The Dense Plasma Focus

Alameda Applied Sciences Corporation (AASC) has built a bench-top source of fast neutrons (approx10-30 ns, 2.45 MeV), that is portable and can be scaled to operate at approx100 Hz. The source is a Dense Plasma Focus driven by three different capacitor banks: a 40 J/30 kA/100 Hz driver; a 500 J/130 kA/2 Hz driver and a 3 kJ/350 kA/0.5 Hz driver. At currents of approx130 kA, this source produces approx1x10{sup 7} (DD) n/pulse. The neutron pulse widths are approx10-30 ns and may be controlled by adjusting the DPF electrode geometry and operating parameters. This paper describes the scaling of the fast neutron output with current from such a Dense Plasma Focus source. For each current and driver, different DPF head designs are required to match to the current rise-time, as the operating pressure and anode radius/shape are varied. Doping of the pure D{sub 2} gas fill with Ar or Kr was shown earlier to increase the neutron output. Results are discussed in the light of scaling laws suggested by prior literature.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Frequency dependent electrical measurements of amorphous GeSbSe chalcogenide thin films

A commercial bulk chalcogenide glass (Ge28Sb12Se60) was used as a source to fabricate amorphous thin films via thermal evaporation technique. At low frequencies (1 MHz) impedance spectroscopy was performed to measure electrical properties. To measure ac conductivity at microwave frequencies, a split resonance cavity technique was applied for which a model based on parallel arrangement of substrate and film capacitors was developed. This model was used to extract tan8 and ac conductivity of the films. Microwave ac conductivity was correlated with the extrapolated low frequency conductivity data confirming applicability of the universal law commonly observed in amorphous semiconductors.

36 MATERIALS SCIENCE↗

Optical and electrical diagnostics of an atmospheric pressure room-temperature plasma plume

Cold plasmas have recently received great attention. In this paper, optical and electrical diagnostics are carried out on a reliable and user-friendly plasma plume. A simple electrical model is used to simulate the electrical characteristics of the device. The plasma is represented by a resistor connected in parallel with a capacitor, an inductor, and another resistor, which are connected in series. The simulated current-voltage waveforms have very good agreement with experimental measurements. Besides, the emission spectra of the plasma are also studied. It shows that, when Ar is used as working gas, there is strong OH (hydroxyl radical) emission and the emission intensities of the N{sub 2} emission bands are more than three times higher than that of He. On the contrary, when He is used as working gas, the emission intensities of N{sub 2}{sup +} band are much stronger. Detail analyses on these observations are presented.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Fast integrator based data acquisition system for the SST-1 Thomson scattering system

An operational transconductance amplifier based fast charge-integrating module (FCIM) is designed and developed for an easy acquisition of fast Thomson scattered and background signal. FCIM based data acquisition technique can be used for the measurement of charge pulses of <20 ns duration. The response of the module is tested using a standard pulsed charge-generating module. The measuring charge range of the module depends on the integrating capacitor. Comparison of the performance of FCIM to commercially available module shows that it has better dynamic range with higher sensitivity and less measurement error. The module is quite cost effective and has many new features.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Hydrophobic fluoroalkylsilane nanolayers for inhibiting copper diffusion into silica

Molecular nanolayers (MNLs) are attractive for suppressing chemical transport and mixing at copper-silica interfaces. Here, we demonstrate that hydrophobic fluoroalkyl moieties enhance the effectiveness of organosilane MNLs to inhibit copper diffusion. Bias thermal annealing of copper-MNL-silica capacitors with MNLs having different fluoroalkyl contents, combined with electron spectroscopy and contact angle measurements, show that the enhanced barrier properties are due to diminished water uptake and curtailed copper ionization. Our results suggest that controlling interface moisture content using hydrophobic moieties can complement copper ion immobilization by hydrophilic groups in MNL barriers.

36 MATERIALS SCIENCE↗

A simple double-focusing electrostatic ion beam deflector

We have developed an electrostatic, double-focusing 90 deg. deflector for fast ion beams consisting of concentric cylindrical plates of differing heights. In contrast to standard cylindrical deflectors, our design allows for focusing of an incoming parallel beam not only in the plane of deflection but also in the orthogonal direction. The optical properties of our design resemble those of a spherical capacitor deflector while it is much easier and more cost effective to manufacture.

43 PARTICLE ACCELERATORS↗

Modeling and Experimental Analysis of Piezoelectric Shakers for High-Frequency Calibration of Accelerometers

Piezoelectric shakers have been developed and used at the National Institute of Standards and Technology (NIST) for decades for high-frequency calibration of accelerometers. Recently, NIST researchers built new piezoelectric shakers in the hopes of reducing the uncertainties in the calibrations of accelerometers while extending the calibration frequency range beyond 20 kHz. The ability to build and measure piezoelectric shakers invites modeling of these systems in order to improve their design for increased performance, which includes a sinusoidal motion with lower distortion, lower cross-axial motion, and an increased frequency range. In this paper, we present a model of piezoelectric shakers and match it to experimental data. The equations of motion for all masses are solved along with the coupled state equations for the piezoelectric actuator. Finally, additional electrical elements like inductors, capacitors, and resistors are added to the piezoelectric actuator for matching of experimental and theoretical frequency responses.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Solid-state Marx based two-switch voltage modulator for the On-Line Isotope Mass Separator accelerator at the European Organization for Nuclear Research

A new circuit topology is proposed to replace the actual pulse transformer and thyratron based resonant modulator that supplies the 60 kV target potential for the ion acceleration of the On-Line Isotope Mass Separator accelerator, the stability of which is critical for the mass resolution downstream separator, at the European Organization for Nuclear Research. The improved modulator uses two solid-state switches working together, each one based on the Marx generator concept, operating as series and parallel switches, reducing the stress on the series stacked semiconductors, and also as auxiliary pulse generator in order to fulfill the target requirements. Preliminary results of a 10 kV prototype, using 1200 V insulated gate bipolar transistors and capacitors in the solid-state Marx circuits, ten stages each, with an electrical equivalent circuit of the target, are presented, demonstrating both the improved voltage stability and pulse flexibility potential wanted for this new modulator.

43 PARTICLE ACCELERATORS↗

Design of microcontroller based system for automation of streak camera

A microcontroller based system has been developed for automation of the S-20 optical streak camera, which is used as a diagnostic tool to measure ultrafast light phenomenon. An 8 bit MCS family microcontroller is employed to generate all control signals for the streak camera. All biasing voltages required for various electrodes of the tubes are generated using dc-to-dc converters. A high voltage ramp signal is generated through a step generator unit followed by an integrator circuit and is applied to the camera's deflecting plates. The slope of the ramp can be changed by varying values of the capacitor and inductor. A programmable digital delay generator has been developed for synchronization of ramp signal with the optical signal. An independent hardwired interlock circuit has been developed for machine safety. A LABVIEW based graphical user interface has been developed which enables the user to program the settings of the camera and capture the image. The image is displayed with intensity profiles along horizontal and vertical axes. The streak camera was calibrated using nanosecond and femtosecond lasers.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗