Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ABLATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,603 records · Page 89
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

The adjunctive effect for left pulmonary vein isolation of vein of Marshall ethanol infusion in persistent atrial fibrillation

Abstract Objective This study sought to assess the effect of ethanol infusion into the vein of Marshall (EIVOM) on the acute success of left pulmonary vein (LPV) isolation in persistent atrial fibrillation (PeAF). Methods and results A total of 313 patients with drug-resistant PeAF were enrolled (135 in Group 1 and 178 in Group 2). In Group 1, EIVOM was firstly performed, followed by radiofrequency ablation (RFA) including bilateral pulmonary vein isolation (PVI) and linear ablation at roofline, cavotricuspid isthmus, and mitral isthmus (MI). In Group 2, PVI and linear ablations were completed with RFA. First-pass isolation of the LPV was achieved in 119 (88.1%) and 132 (74.2%) patients in Groups 1 and 2, respectively (P = 0.002). The rate of acute pulmonary vein reconnection (PVR) was significantly lower in Group 1 (9.6% vs. 22.5%, P = 0.003). About half of acute PVR occurred in the carina with or without EIVOM. Conclusion EIVOM is effective in achieving a higher first-pass isolation and a lower acute PVR of LPV in PeAF.

Huang, Lihong (ORCID:000000027261316X)↗
DOE OSTI2018

Measuring the shock impedance mismatch between high-density carbon and deuterium at the National Ignition Facility

Fine-grained diamond, or high-density carbon (HDC), is being used as an ablator for inertial confinement fusion (ICF) research at the National Ignition Facility (NIF). Accurate equation of state (EOS) knowledge over a wide range of phase space is critical in the design and analysis of integrated ICF experiments. Here in this paper, we report shock and release measurements of the shock impedance mismatch between HDC and liquid deuterium conducted during shock-timing experiments having a first shock in the ablator ranging between 8 and 14 Mbar. Using ultrafast Doppler imaging velocimetry to track the leading shock front, we characterize the shock velocity discontinuity upon the arrival of the shock at the HDC/liquid deuterium interface. Comparing the experimental data with tabular EOS models used to simulate integrated ICF experiments indicates the need for an improved multiphase EOS model for HDC in order to achieve a significant increase in neutron yield in indirect-driven ICF implosions with HDC ablators.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Novel Hot-Spot Ignition Designs for Inertial Confinement Fusion with Liquid-Deuterium-Tritium Spheres

A new class of ignition designs is proposed for inertial confinement fusion (ICF) experiments. These designs are based on the hot-spot-ignition approach, but instead of conventional targets that comprise of spherical shells with thin frozen deuterium{tritium (DT) layers, homogeneous-density (solid or liquid) DT spheres are used where the lower-density central region and higher-density shell are created dynamically by appropriately shaping the laser pulse. These offer several advantages, including simplicity in target production and lower sensitivity to both laser imprint and physics uncertainty in shock interaction with the ice-vapor interface. The design evolution starts by launching an ~1-Mbar shock into a homogeneous DT sphere. After bouncing from the center, the reflected shock reaches the outer surface of the sphere and the shocked material starts to expand outward until its pressure drops below the ablation pressure. At this point, an adjustment shock is launched inward by supporting ablation pressure. This shock compresses the ablator and fuel, forming a shell. The shell is then accelerated and compressed by appropriately shaping the drive laser pulse, similar to the conventional thin-shell, hot-spot designs. Here, this paper demonstrates the feasibility of the new concept using hydrodynamic simulations and discusses the advantages and disadvantages of the concept compared with more-traditional ICF designs.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Hot Spot Evolution Measured by High-Resolution X-Ray Spectroscopy at the National Ignition Facility

Evolution of the hot spot plasma conditions was measured using high-resolution x-ray spectroscopy at the National Ignition Facility. The capsules were filled with DD gas with trace levels of Kr and had either a high-density-carbon (HDC) ablator or a tungsten (W)-doped HDC ablator. Time-resolved measurement of the Kr He β spectra, absolutely calibrated by a simultaneous time-integrated measurement, allows inference of the electron density and temperature through observing Stark broadening and the relative intensities of dielectronic satellites. By matching the calculated hot spot emission using a collisional-radiative code to experimental observations, the hot spot size and areal density are determined. Here these advanced spectroscopy techniques further reveal the effect of W dopant in the ablator on the hot spot parameters for their improved implosion performance.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2018

On the Problem of Thermonuclear Ignition and Burning in the NIF Laser: Ignition with Capsules Taking into Account the Influence of the Hohlraum Radiation on Implosion

One of the significant problems of modern physics is the creation and use of new energy sources. The decisive step in this direction is the realization of a positive yield in thermonuclear energy on a laboratory scale with the facilities that create and retain plasma. Between 2010 and 2017, a large series of experiments were performed at the National Ignition Facility laser at the Livermore Laboratory in the United States with the aim of achieving such a positive outcome. Until now, however, the ignition has not been reached. In this paper, for the first time the influence of the hohlraum radiation on capsule layers including a deuterium–tritium layer is discussed. It is shown that the negative influence of the ablator transparency can be compensated for by the selection of a capsule design with a greater optical thickness of the part of the ablator. This part of the ablator is not evaporated upon heating by an X-ray pulse. The design of such a capsule is proposed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Laser-Induced Plasmas of Plutonium Dioxide in a Double-Walled Cell

Plutonium research has been stifled by the significant number of administrative controls and safety procedures, space and instrumentation limitations in radiological gloveboxes, and the potential for personnel and equipment contamination. To address the limited number of spectroscopic studies in Pu-bearing compounds in the current scientific literature, this work presents the use of double-walled cells (DWCs) in “clean” buildings/laboratories as an alternative to research in radiological gloveboxes. This study reports the first laser-induced breakdown spectroscopy (LIBS) experiments of a PuO 2 pellet contained within a DWC, where the formation of elemental (atomic and ionic) species as well as the evolution from elemental to molecular products (Pu x O y ) was measured. Raman spectroscopy was also used to characterize the surface of the ablated pellet and the particulates deposited on the window of the inner cell. The full width half-maximum of the T 2g band enabled us to obtain an estimate of the temperature at the pellet surface after the ablation pulse and the particulates based on the crystal lattice disorder. Particulates deposited on the window of the DWC during laser ablation were characterized using scanning electron microscopy, where molten irregular particulates and spheroids were observed. This exciting research conducted in a DWC describes our initial attempts to incorporate LIBS in the arsenal of spectroscopic tools for nuclear forensics applications.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2018

Probing the Interface Stability of Implosions

In the quest for reaching ignition of deuterium-tritium (DT) fuel capsule implosions, experiments on the National Ignition Facility have shown lower final fuel areal densities than simulated. Possible explanations for reduced compression are higher preheat that can increase the ablator-DT ice density jump and induce mix at that interface, or reverberating shocks. We were hence interested in developing x-ray Refraction Enhanced Radiography (RER) to infer the inflight density profiles in layered fuel capsule implosions. The first experiments validated our setup by recording a streaked x-ray fringe pattern from an undriven high density carbon (HDC) capsule consistent with raytracing calculations at the required ~ 6 micron and 25 ps resolution. Streaked RER was then applied to inflight cryogenically layered HDC capsule implosions using a hydrogen-tritium fuel mix. The first RER of an inflight capsule revealed strong features associated with the ablation front and ice-ablator interface that are not visible in standard absorption in-flight radiographs.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗
DOE OSTI2019

Amorphous Carbon Coatings with Controlled Density and Composition

Inertial confinement fusion (ICF) experiments rely on the compression of a spherical capsule containing tritium and deuterium fuel as a way to achieve thermonuclear fusion. Rapid ablation of the capsule surface produces the reactive force that compresses the capsule. Carbon-based capsule materials currently used include low density glow discharge polymer (GDP) and polycrystalline diamond. An ideal capsule material would have the high density of diamond, with the amorphous nature of GDP, which would reduce asymmetries during compression caused by a random crystalline structure. An intermediate material, diamond-like carbon (DLC), has an amorphous structure, and densities between GDP and diamond, but has been difficult to produce with low stress and low impurity levels. The goal of this Feasibility Study was to investigate the practicality of using a magnetically enhanced, hollow-cathode, plasma source to produce thick (50-200 µm), low-stress, diamond-like carbon films for ICF ablator applications. The coatings produced during the course of this work have been shown to be amorphous, to have a higher density than traditional GDP ablators (1.6-1.7 g/cc), to have low stress (67-113 MPa), and can be deposited at the high thicknesses required for ICF capsule requirements. Atomic-force microscopy on a 45-micron-thick coating also measured the films to have grain sizes on the order of 20 nanometers, and a root-mean squared surface roughness of 0.5 nanometers.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Exploring Deuterium-Tritium Gas-Filled Hohlraums as a High-Yield Neutron Source

Inverted-corona targets as neutron sources for high-energy-density applications were tested experimentally using the OMEGA laser. In a corona fusion target, laser beams directly ablate a layer of fusion fuel on the inner surface of a capsule. As the ablative flows converge, the plasma particles transition to collisional stagnation, heating the ions and generating fusion reactions. Based on a recent publication these targets show promise as a neutron source, with extrapolated yields at NIF scale of up to 1e17. Additionally, these targets are robust to low-mode drive asymmetries, enabling the possibility of single-sided laser drive, making them an ideal backlighter source for neutron-radiography applications. A number of different targets were fielded in experiments on the OMEGA laser. The 1.8-mm diameter plastic (CH) capsules featured either one or two laser-entrance holes (LEH’s), and were either lined with deuterated plastic (CD), or filled with 1.5-atm deuterium gas. Contrary to predictions by the hydrodynamics code HYDRA, the experiments exhibit a strong correlation between total neutron yield and CD liner thickness, indicating substantial mix of CH wall material into the ablated CD coronal plasma. The thickest liner targets with approximately 10 kJ of incident laser energy performed consistent with previously published data, while the data at 18 kJ laser energy may also be subject to mix from wall material. The yield from the gas-filled capsules was less than from 10-μm CD lined targets at the same laser energy, which may als be explained by wall material mixing into the fusion fuel. Finally, the experiments demonstrated similar performance between a 1-LEH and a 2-LEH target irradiated with comparable laser-energies, a key finding for demonstrating the utility of the inverted-corona neutron source for radiography applications. Future work will focus on developing the platform for NIF experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Hot Electron Scaling and Energy Coupling In Nonlinear Laser Plasma Interactions

Energy conversion from high power lasers to energetic hot electrons is a fundamental phenomenon in laser-plasma interactions. At laser intensities above a few times 10 14 W/cm 2 , nonlinear laser-plasma interactions lead to the generation of hot electrons with a broad energy distribution at typical temperatures of 10’s – 100’s kilo-electron-volt (keV). The fraction of laser energy transferred to hot electrons, their energy distribution and energy coupling efficiency to the targets are strongly affected by the laser intensity, wavelength and the plasma condition. Most investigations to date that are related to the fusion of high-energy-density laboratory plasmas (HEDLP) are carried out with relatively moderate laser intensity and lower laser wavelength to minimize hot electron generation, as electron preheating can degrade the fuel assembly. An alternative fusion scheme known as shock ignition (SI) has been proposed, requiring a high intensity spike pulse at the end of a fuel assembly phase to generate a strong shock to ignite the fuel. An initial shock pressure of 0.3 Gbar is required for ignition-scale targets using the SI scheme, requiring a relatively high on-target laser intensity of 5-10X10 15 W/cm 2 for the spike pulse. At such intensities, copious hot electrons can be produced by laser-plasma-instabilities (LPI), e.g., Stimulated Raman Scattering (SRS) and Two-Plasmon Decay (TPD). While very energetic electrons (>200 keV) could preheat the fuel, electrons with moderate energies may actually be beneficial for the SI scheme. Electrons in the 50-100 keV range can be stopped in the compressed high-density outer ablator layer leading to an increase in the ignitor shock strength and therefore enhancing overall efficiency in the SI scheme. Considering this importance of total energy and temperature of hot electrons, it is necessary to understand the LPI in the SI high intensity regime. Characterizing the hot electron source and energy coupling is key to investigating the viability of the SI concept. The overall goal of the HEDLP award was to perform a detailed study of the scaling of hot electron generation and energy coupling on high power laser systems, with intensity, wavelength, and target ablator material relevant to the nonlinear laser-plasma interaction at SI relevant conditions. This was a collaborative project between the Center for Energy Research at the University of California, San Diego (UCSD) and General Atomics. The experiment was performed at the Omega Laser Facility at the Laboratory for Laser Energetics (LLE) in the University of Rochester. Specific objectives of the work were to: understand the basic physics of laser-plasma interactions and instabilities at high laser intensities (up to 10 17 W/cm 2 ) and the effects of low-Z ablator materials and laser wavelengths (IR pulse at 1.054 µm versus UV pulse at 0.351 µm) and intensity scaling, fully characterize the resultant hot electron energy distribution, validate hot electron energy deposition via collisional and kinetic processes in the target and the induced shocks in support of electron-assisted SI concept.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Diagnosing Field Strengths and Plasma Conditions in Magnetically Insulated Transmission Lines Using Active Dopant Spectroscopy

Experimental validation data is needed to inform simulations of large pulsed power devices which are in development to understand and improve existing accelerators and inform future pulsed power capabilities. Using current spectroscopic techniques on the Z-machine, we have been unable to reliably diagnose plasma conditions and electric and magnetic fields within power flow regions. Laser ablation of a material produces a low density plasma, resulting in narrow spectroscopic line widths. By introducing a laser ablated plasma to the anode cathode gap of the Mykonos accelerator, we can monitor how the line shapes change due the current pulse by comparing these line shapes to spectral measurements taken without power flow. In this report we show several examples of measurements conducted on Mykonos on various dopant materials. We also show a negligible effect on power flow due to the presence of the ablation plasma for a range of parameters.

43 PARTICLE ACCELERATORS↗
DOE OSTI2020

National Ignition Campaign Data Analysis by an ICF Outsider

A simple DT burn model, with no alpha-particle warming feedback, using a combination of ICF inputs and the measured ion temperature, T, volume compression, C, ablator velocity, v, and burn width time, Δt, can reproduce the national-ignition campaign (NIC) fusion yields with a rms percent difference of ~40%. Analysis suggestion the fusion-yield reproducibility of NIC events with nominally identically measured T, C, v, and Δt is <30%. The highest fusion yields, at a fixed laser energy are obtained with depleted-uranium (DU) hohlraums and high-density carbon (HDC) ablators. Small diameter fit tubes (≤5 μm) enhance fusion yields by an average of 26±15% relative to 10-μm diameter fit tubes. A dependence of fusion yield on the diameter of the capsule relative to the diameter of the hohlraum is inferred for fixed T, C, v, and Δt. No evidence of conditions close to ignition, or alpha-particle warming is found in the existing NIC data with LEH< 2MJ. To obtain a predictive model for extrapolation proposes we map the T, C, and v into power laws as a function of LEH. The above mentioned extrapolatable model has a rms percent difference from the yields of the second half of the NIC of (56 ± 4)%. Higher (and significantly lower) DT temperatures are obtained with HDC ablators (and low-foot drives). The highest compressions are obtained via low-foot drives, but this does not compensate for the corresponding lower temperatures. An extrapolation of the presented model suggests significant alpha-particle heating at an LEH of ~5 MJ. It is hoped that others more familiar it the conditions needed for ignition will use to presented model to estimate the LEH required for ignition.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

In-situ Laser Induced Breakdown Spectroscopy Measurements in PISCES-A

The goal of the project was to develop a Laser Induced Breakdown Spectroscopy (LIBS) diagnostic that could be employed during the plasma exposure of targets in the PISCES-A linear plasma device to interrogate the surface as the plasma exposure progressed. The objectives of the measurements were twofold; first, to measure in real-time the composition of elements in the near surface ablated zone to enable a tool that could be used to validate material migration models of eroded material, and second, to measure the plasma fuel contained in the ablated surface to determine the static and dynamic inventory of gas in a target during the plasma exposure. The LIBS diagnostic was successfully deployed on PISCES-A and measured both elemental composition and gas accumulation in the near-surface ablated layer during plasma operations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Full Technical Report: High-Rate Carbide Growth by Evaporation

Boron carbide (B 4 C) is an attractive inertial confined fusion (ICF) ablator and a unique ultra-hard material with numerous current and potential applications. What makes B 4 C attractive as an ablator is its relatively high density and the ability to form a stable glassy phase combined with excellent chemical and mechanical stability. Despite these advantages, the fabrication of B 4 C ablators has remained a challenge. Magnetron sputtering, our current frontrunner approach for B 4 C deposition, exhibits low deposition rates (< 2 μm/h) and undesirable nodular defects within the film structure that are believed to generate from the dusty plasma around the sputtering source. The goals of this project were to (1) establish alternative plasma-free, electron beam evaporation (EBE) capabilities for the deposition of thin films that are needed in mission-critical programs and; (2) demonstrate the feasibility to deposit B 4 C films at high rates by EBE in a bottom-up geometry and characterize their stoichiometry. In this feasibility study, we initially developed the capability to convert a general-use vacuum chamber into an electron beam evaporator as needed, or on demand. Then, we successfully used this setup to deposit films made of boron carbide and various other materials. By adjusting the deposition parameters and the evaporation source material, we were able to demonstrate the feasibility of reaching deposition rates as high as 8 μm/h, which is about 4 times the maximum rates obtained through sputtering methods. We predict that these values can still be further improved by implementing enhanced thermal control measures for the target source and optimizing electron beam parameters (ie. current, sweeping and frequency) since ceramic materials with similar densities to B 4 C can exhibit deposition rates of about twice this value. We anticipate that the skills and capabilities developed throughout this project will prove relevant not only to the HED and ICF campaigns but also to numerous existing and prospective applications focused on the development of ultra-hard carbide coatings. The fresh set of tools here developed will also facilitate the preparation and research on future new target materials of interest beyond B 4 C.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Low-cost Manufacturing of Semitransparent CdTe PV for Building Integration

Solar has been demonstrated to be a robust renewable energy source, constituting a significant portion of the United States’ renewable energy portfolio. Despite its growth across residential, commercial, and utility sectors over the past decades, it remains a small fraction of the overall energy infrastructure. Challenges persist in fully harnessing solar power to meet the nation's escalating energy demands. Among these challenges lies the hurdle of efficiently distributing large quantities of solar-generated electricity to densely populated regions with the highest energy needs and costs. Traditional utility-scale arrays demand extensive land, a luxury often unavailable in metropolitan areas. Consequently, installations must be situated at a distance, necessitating additional infrastructure for electricity transmission to service areas. While metropolitan landscapes lack sprawling open spaces suitable for conventional utility-scale solar deployment, they offer a different resource: windows. Semitransparent photovoltaic window technology has the potential to not only bolster the grid's energy capacity, but to also provide HVAC and economic advantages to building owners. However, commercial availability of building-integrated photovoltaic windows remains limited. Silicon based photovoltaics currently dominate the solar market but adapting them for use in windows poses a variety of engineering and economic challenges such as relatively low power density, high costs associated with custom manufacturing, and aesthetic considerations. Addressing these challenges, this project explored the use of laser ablation patterning to manufacture cost-effective, high-efficiency, semitransparent Cadmium Telluride photovoltaic modules. Results showcased the potential of this methodology in developing photovoltaic windows and other innovative semitransparent PV applications. The ablation manufacturing technique demonstrated great versatility in achieving different patterns and levels of visible light transmission, and the power loss due to ablation was nearly directly proportional to the amount of material removed. Furthermore, the manufacturing process for Cadmium Telluride modules already has established advantages in material and energy efficiency, and the conversion of a standard submodule to semitransparent essentially requires a single additional process step, ensuring scalability. It is important to note that during this work, Toledo Solar experienced substantial organizational upheaval stemming from a lawsuit with First Solar. An external investigation led the board of directors to remove and replace the previous management team, and several other members of the staff elected to depart as well, including the then acting Principle Investigator on this project. The remaining Toledo Solar team attempted to recover from the disruption and deliver on the remaining tasks, but upon its own review, the Department of Energy ruled the project in default and terminated the contract in December 2023.

14 SOLAR ENERGY↗
DOE OSTI2022

Fast Characterization of Inducible Regions of Atrial Fibrillation Models With Multi-Fidelity Gaussian Process Classification

Computational models of atrial fibrillation have successfully been used to predict optimal ablation sites. A critical step to assess the effect of an ablation pattern is to pace the model from different, potentially random, locations to determine whether arrhythmias can be induced in the atria. In this work, we propose to use multi-fidelity Gaussian process classification on Riemannian manifolds to efficiently determine the regions in the atria where arrhythmias are inducible. We build a probabilistic classifier that operates directly on the atrial surface. We take advantage of lower resolution models to explore the atrial surface and combine seamlessly with high-resolution models to identify regions of inducibility. We test our methodology in 9 different cases, with different levels of fibrosis and ablation treatments, totalling 1,800 high resolution and 900 low resolution simulations of atrial fibrillation. When trained with 40 samples, our multi-fidelity classifier that combines low and high resolution models, shows a balanced accuracy that is, on average, 5.7% higher than a nearest neighbor classifier. We hope that this new technique will allow faster and more precise clinical applications of computational models for atrial fibrillation. All data and code accompanying this manuscript will be made publicly available at: https://github.com/fsahli/AtrialMFclass.

59 BASIC BIOLOGICAL SCIENCES↗
NASA NTRS1972

Effect of thermally expanding surfaces on aerodynamic roll torques for cones.

An experimental and analytical study has been made of the aerodynamic roll torque on smoothly ablating, spinning cones. The tests, conducted in the Ames 3.5-Foot Hypersonic Wind Tunnel, indicated that the smoothly ablating model rolling at 0 deg angle of attack experiences roll damping, but when rolling at angle of attack an aerodynamic torque in the direction of spin arises if thermal expansion of the body surface occurs. An analysis of the spinning body at angle of attack is included to show how the relative importance of the ablator thermal expansion and the surface recession rate determines whether the motion is damped or undamped.

Mcdevitt, J. B.↗
NASA NTRS1974

Outer planet probe entry thermal protection. I Aerothermodynamic environment

Solutions are presented for the aerothermal heating environments about blunt probes of various shape entering the candidate atmospheres of Saturn and Uranus. The analysis makes use of a series of interacting codes to predict pressures, cold wall radiative fluxes, cold wall convective fluxes, and corresponding corrections for the radiative and convective fluxes. The solutions show that ablation will either enhance or reduce the radiative flux to the surface depending on the ablation gas composition and ablation rate. Other conclusions suggested by the solutions are discussed.

Nicolet, W. E.↗