SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The beam-foil technique has been used to study the 2S(2)S-2p(2)P(0) doublet in S XIV. The results confirm the doublet splitting measured aboard Skylab during solar flare events. In addition, the oscillator strengths for the resonance transitions comprising this doublet have been measured and found to agree well with recent relativistic f-value calculations.
The effect of surface finish on the strength-grain size relation was investigated for dense hot-pressed SiC. Failure initiated predominantly via the propagation of extrinsic machining-induced flaws for the range of grain sizes and machining grit sizes studied. These results are consistent with the region of large-grain-size flaw control as delineated by Prochazka and Charles. The severity of machining-induced flaws, relative to the machining grit size, decreased with increasing machining grit size and decreasing SiC grain size.
High-resolution magnetograms place an upper limit of 0.33 arcsec on the smallest magnetic-field structures. These magnetograms show that the active-region field is organized into roughly cellular patterns 2-3 arcsec in diameter and that the field structures occur in the centers of 'abnormal' granules. Comparison of these data and other magnetograms with high signal-to-noise ratio indicates that there exists another component of the field that is diffuse on the scale of an arc second and has a maximum strength of less than 500 gauss.
Boron-on-tungsten fibers with tensile strength and strain-to-failure values increased by fifty percent over commercial grades are produced by controlled chemical-etching process. Improved fibers have potential applications as lightweight composites in ground vehicles, spacecraft, and rotors for energy storage.
Four-part report describes processing procedures for high-strength alloy steel suitable for use in pistons, piston rods, cylinder barrels, and other critical applications.
A study of the flow strength, creep resistance and diffusion welding characteristics of the titanium alloy Ti-6Al-2Nb-1Ta-0.8Mo was conducted. Two mill-processed forms of this alloy were examined. The forged material was essentially processed above the beta transus while the rolled form was subjected to considerable work below the beta transus. Between 1150 and 1250 K, the forged material was stronger and more creep resistant than the rolled alloy. Both forms exhibit superplastic characteristics in this temperature range. Strain measurements during diffusion welding experiments at 1200 K reveal that weld interfaces have no measurable effect on the overall creep deformation. Significant deformation appears to be necessary to produce a quality diffusion weld between superplastic materials. A 'soft' interlayer inserted between faying surfaces would seemingly allow manufacture of quality diffusion welds with little overall deformation.
Acoustic emission was used for the detection of fatigue cracking in a number of high-strength light alloys used in aeronautical structures. Among the features studied were: the influence of emission frequency, the effect of surface oxidation, and the influence of grains. It was concluded that acoustic emission is an effective nondestructive technique for evaluating the initiation of fatigue cracking in such materials.
Thermomechanical processing (TMP) was evaluated as a method of strengthening normally tough iron-12-nickel-reactive metal alloys at cryogenic temperatures. Five iron-12 nickel alloys with reactive metal additions of aluminum, niobium, titanium, vanadium, and aluminum plus niobium were investigated. Primary evaluation was based on the yield strength and fracture toughness of the thermomechanically processed alloys at -196 C.
The tensile strength of boron-epoxy/aluminum sandwich laminates is discussed relative to the residual thermal stresses generated by curing and bonding at elevated temperatures. It is shown that the sandwich laminates investigated exhibit three dinstinct modes of failure, depending upon the fiber orientation of the composite. Sandwich laminates with moderate to high percentage of 0-deg fibers exhibit early failures initiated by edge effect; laminates with moderate to high percentage of 90-deg fibers fail according to a first-ply failure criterion; laminates with moderate to high percentages of plus or minus 45 deg plies fail at strains equal to or greater than the failure strain of the corresponding all-composite laminate.
The Hoffman theory and the Tensor Polynomial (Tsai-Wu) theory with the stress interaction term set equal to zero have been found to be preferred alternatives to the general Tensor Polynomial theory for predicting strength of filamentary composite laminae. These theories were used to predict failure of off-axis boron/epoxy and E-glass/epoxy test specimens and gave excellent agreement with available experimental results. A numerical experiment was also performed to estimate the errors for ten different composite systems under six different loadings. The maximum error in predicted failure loads among all cases was below 10 percent. These results suggest that the Hoffman failure theory and the Tensor Polynomial theory with the stress interaction term equal to zero can predict failure of practical filamentary composite materials under general biaxial loading with sufficient accuracy for engineering applications.
The buffer rod technique for measuring attenuation in thin specimens is modified here to apply to specimens having intermediate thicknesses and high attenuation. The described procedure, which requires only one accessible surface of the material, was used to determine the initial attenuation values of ultrasonic waves in short beam shear specimens of graphite-polyimide composite material. It is shown that there is good correlation between the initial attenuation values and the shear strengths of the specimens determined by the standard short beam shear test method. The modified ultrasonic buffer block technique offers much potential for service as a quantitative, nondestructive, quality assurance test for composite materials.
An unstiffened panel buckling constraint for balanced, symmetric laminated composites is included on the global design level in a mathematical programming structural optimization procedure for designing wing structures. Constraints are introduced by penalty functions, and Newton's method based on approximate second derivatives of the penalty terms is used as the search algorithm to obtain minimum-mass designs. Constraint approximations used during the optimization process contribute to the computational efficiency of the procedure. A criterion is developed that identifies the appropriate conservative form of the constraint approximations that are used with the optimization procedure. Minimum-mass design results are obtained for a multispar high-aspect-ratio wing subjected to material strength, minimum-gage, displacement, panel buckling and twist constraints. The material systems considered for the examples are all graphite-epoxy, graphite-epoxy with boron-epoxy spar caps, and all aluminum. The composite material designs are shown to have an advantage over the aluminum designs since they can often satisfy additional constraints with only small mass increases.
A general theory of the compressive strength of brittle materials is presented. This theory proposes that failure is brought about by structural weakening from accumulated crack damage which increases with the stress level. The statistics of the flaw distribution and the mechanism of crack initiation and extension are important. A sample calculation using the theory is given to demonstrate its application
Strengthening and forming process for prealloyed powder superalloys greatly increases material strength in the 900-1,200F temperature range. Process which involves superplastically-deforming compacted powders at controlled rates and temperature is most effective on nickel-base alloys.
Graphite/epoxy strengths at various moisture contents are estimated by extrapolating from small data base. With procedure, massive testing is unnecessary because advantage is taken of large data base already available for moisture content in laminates.
Report describes results of stress-corrosion tests on aluminum alloys 7075, 7475, 7050, and 7049. Tests compare performance of original stress-corrosion-resistant (SCR) aluminum, 7075, with newer, higher-strength SCR alloys. Alloys 7050 and 7049 are found superior in short-transverse cross-corrosion resistance to older 7075 alloy; all alloys are subject to self-loading effect caused by wedging of corrosion products in cracks. Effect causes cracks to continue to grow, even at very-low externally applied loads.
Shear-strength tests on aluminum fillet welds are documented in report. Test were made on aluminum alloy 2219 to aid designers in specifying sizes and lengths of fillet welds necessary to sustain expected loads in this material. Report discusses fillet-weld size and geometry, including root penetration and surface contour.
Metal fiber reinforced superalloys are being considered for construction of critical components in turbine engines that operate at high temperature. The problems involved in fabricating refractory metal alloys into wire form in such a manner as to maximize their strength properties without developing excessive structural defects are described. The fundamental principles underlying the development of such alloy fibers are also briefly discussed. The progress made to date in developing tungsten, tantalum and columbium base alloys for fiber reinforcement is reported and future prospects for alloy fiber development considered.