Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “material strength”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,585 records · Page 88

Synthesis and Characterization of Aluminum Matrix Composites Reinforced with (Ni,Cu){sub 3}Al Intermetallic Particles via Mechanical Milling Technique

This study investigates the dispersion of (Ni,Cu){sub 3}Al intermetallic particles in an aluminum matrix via low-energy mechanical milling as an alternative to conventional stir casting. The precursor powders consisted in (Ni,Cu){sub 3}Al and reactive-grade Al particles with an average size of 15 and 3 microns, respectively. The concentrations used were 3, 5, 8 and 10 wt.% of the intermetallic powders. After 4 h of milling, the obtained powders were compacted in a unidirectional press with a pressure of 930 MPa and the obtained green compacts were sintered at 500 °C in a controlled atmosphere oven for 2 h. Result showed that the bulk composites displayed an increase in the Vickers microhardness as well as an increase in compressive strength and stiffness as the percentage of dispersed particles increased. The Al-8 wt.%(Ni,Cu){sub 3}Al sample achieved the best performance and is related to the findings in SEM micrographs that showed that higher reinforcement concentration increased the formation of microporosities that reduce the decohesion of the bulk sample and impact heavily on the mechanical performance of the material.

36 MATERIALS SCIENCE↗

Design and Analysis of an Advanced Three-Point Bend Test Approach for Miniature Irradiated Disk Specimens

Candidate tungsten armor materials in a magnetic confinement fusion device must be able to withstand thermal variation that leads to internal stresses caused by the impinging heat load. In addition, the thermomechanical properties of these materials are degraded by irradiation-induced defect accumulation. Fission reactor–based irradiation data are used to predict the fusion neutron damage and property change. This study examines the motivation and design of a custom-designed three-point bend test for neutron-irradiated disk specimens that are 3 mm in diameter to be able to define the flexural strength of advanced tungsten materials, alloys, and composites—and to the extent that embrittlement occurs after neutron irradiation. The theory provided shows a calculation for the flexural deflection and shear deflection due to the small-geometry constraints. A finite element deformation analysis is performed to evaluate the mechanical stress field of disk bend specimens. The stress values above 80% of the maximum stress are concentrated in 2.4 mm of the 3.0-mm length of the centerline across the tungsten disk diameter. A bend test fixture has been designed and fabricated to enable testing of these specimens with precisely engineered tolerance and minimal machine compliance. This fixture will be able to be placed inside a universal testing frame at elevated temperatures for the mechanical property evaluation of future neutron-irradiated disk specimens.

36 MATERIALS SCIENCE↗

Matrix Cracking in Four Different 2D SiC/SiC Composite Systems

Silicon carbide fiber reinforced, silicon carbide matrix composites are some of the most advanced composite systems for high-temperature, high-stress applications in oxidizing environments. A basic area that needs to be understood for the purpose of material behavior modeling and optimization is the architectural, constituent, and mechanistic factors that contribute to non-linear stress-strain behavior. The mechanism that causes non-linear stress-strain in dense-matrix composites is the formation and propagation of bridged matrix cracks. In addition, the occurrence and propagation of matrix cracks controls the time-dependent strength-properties of these materials in oxidizing environments at elevated temperatures. A modal acoustic emission technique has been used to monitor and estimate the stress-dependent matrix cracking. Two different SiC matrix systems, chemical vapor infiltrated (CVI) and melt-infiltrated (MI), with two different SiC fiber reinforcement, Hi-Nicalon (trademark) and Sylramic (trademark) were compared. Even though the averages of the range where matrix cracking occurred for the composites varied by more than 0.1% in strain and almost 200 MPa in stress, the range or distribution for matrix cracking could be reduced to a narrow band of stress for CVI SiC and MI SiC composites if it were assumed that all matrix cracks emanate outside of the load-bearing fiber, interphase, CVI preform minicomposite. A simple relationship was determined to describe stress-dependent matrix cracking which can then be used to estimate the onset of large, bridged matrix cracks or for material behavior models.

Morscher, Gregory N.↗

TDNiCr (ni-20Cr-2ThO2) forging studies

Elevated temperature tensile and stress rupture properties were evaluated for forged TDNiCr (Ni-20Cr-2ThO2) and related to thermomechanical history and microstructure. Forging temperature and final annealed condition had pronounced influences on grain size which, in turn, was related to high temperature strength. Tensile strength improved by a factor of 8 as grain size changed from 1 to 150 microns. Stress-rupture strength was improved by a factor of 3 to 5 by a grain size increase from 10 to 1000 microns. Some contributions to the elevated temperature strength of very large grain material may also occur from the development of a strong texture and a preponderance of small twins. Other conditions promoting the improvement of high temperature strength were: an increase of total reduction, forging which continued the metal deformation inherent in the starting material, a low forging speed, and prior deformation by extrusion. The mechanical properties of optimally forged TDNiCr compared favorably to those of high strength sheet developed for space shuttle application.

Filippi, A. M.↗

Mechanical strength of [HA/Bioplastic/Sericin] composite part printed by bioprinter

The aim of this research was to determine the effect of hydroxyapatite (HA) content in printed biocomposite to its mechanical strength. The biocomposite paste was prepared by composing HA, bioplastic and sericin with various ratios of [HA/Bioplastic]: 40/60, 50/50, 60,40 and 70/30. Sericin of 0.3% weight was added to the biocomposite. Mechanical test was conducted to observe tensile (ASTM D 638 type 4) and flexural strength (ASTM D 790). Both type of specimens were fabricated using 3D Printer. Printing process parameter (infill speed, print speed and layer height) were set up as 60 mm/s, 10 mm/s, 0.35 mm, respectively. Results showed that biocomposite with [HA/Biplastic]. weight ratio of 60/40(w/w) has an optimum tensile (3.89 ± 1.26 MPa) and flexural strength (2.51 ± 0.45 MPa). Scanning electron microscope observation indicated that microstructure of specimen was influenced by the percentage of the hydroxyapatite. There was no agglomeration of HA particle within the composite.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Microstructural changes in NiO–ScSZ composite following reduction processes in pure and diluted hydrogen

A Ni–ScSZ cermet is widely used as the anode in a solid oxide fuel cell because it possesses the appropriate electrochemical properties. However, it is susceptible to degradation during operation. Samples of a NiO–ScSZ composite were reduced in pure and diluted hydrogen to determine the microstructural evolution and the degradation behavior of the material. The resulting changes in microstructure were investigated using scanning transmission electron microscopy, X-ray energy dispersive spectroscopy and electron energy loss spectroscopy. The resulting data revealed that the various conditions during the reduction processes had a significant effect on the microstructures. The high porosity of the reduced nickel phase and cracking between the Ni and the ZrO{sub 2} phases after reduction resulted in a reduction in the strength of the anode material. - Highlights: • Structure of NiO/Ni strongly depends on the concentration of reduction atmosphere • Scandium rich precipitations are visible in YSZ phase after reduction process • Nanopores and nanograins are formed in reduced Ni phase.

36 MATERIALS SCIENCE↗

Boron Filled Siloxane Polymers for Radiation Shielding

The purpose of the present work was to evaluate changes to structure-property relationships of 10 B filled siloxane-based polymers when exposed to nuclear reactor radiation. Highly filled polysiloxanes were synthesized with the intent of fabricating materials that could shield high neutron fluences. The newly formulated materials consisted of cross-linked poly-diphenyl-methylsiloxane filled with natural boron and carbon nanofibers. This polymer was chosen because of its good thermal and chemical stabilities, as well as resistance to ionizing radiation thanks to the presence of aromatic groups in the siloxane backbone. Highly isotopically enriched 10 B filler was used to provide an efficient neutron radiation shield, and carbon nanofibers were added to improve mechanical strength. This novel polymeric material was exposed in the Annular Core Research Reactor (ACRR) at Sandia National Labs to five different neutron/gamma fluxes consisting of very high neutron fluences within very short time periods. Thermocouples placed on the specimens recorded in-situ temperature changes during radiation exposure, which agreed well with those obtained from our MCNP simulations. Changes in the microstructural, thermal, chemical, and mechanical properties were evaluated by SEM, DSC, TGA, FT-IR NMR, solvent swelling, and uniaxial compressive load measurements. In conclusion, our results demonstrate that these newly formulated materials are well-suitable to be used in applications that require exposure to different types of ionizing conditions that take place simultaneously.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Aerospace applications of advanced aluminum alloys

Advanced metallic materials within the Al-base family are being developed for applications on current and future aerospace vehicles. These advanced materials offer significant improvements in density, strength, stiffness, fracture resistance, and/or higher use temperature which translates into improved vehicle performance. Aerospace applications of advanced metallic materials include space structures, fighters, military and commercial transport aircraft, and missiles. Structural design requirements, including not only static and durability/damage tolerance criteria but also environmental considerations, drive material selections. Often trade-offs must be made regarding strength, fracture resistance, cost, reliability, and maintainability in order to select the optimum material for a specific application. These trade studies not only include various metallic materials but also many times include advanced composite materials. Details of material comparisons, aerospace applications, and material trades will be presented.

Chellman, D. J.↗

Additive Manufacturing of Corrosion Resistant UHTC Materials for Chloride Salt-to-sCO2 Brayton Cycle Heat Exchangers

The objectives of the project include: (1) screen high-purity, high density ultra-high-temperature ceramics (UHTCs) for chloride salt corrosion resistance, (2) develop binder-jet additive manufacturing and sintering for ZrB 2 -MoSi 2 blends using literature and experiments to demonstrate feasibility, and (3) evaluate chloride salt corrosion resistance of additively manufactured ZrB 2 -MoSi 2 . These initial objectives support the development of a durable and reliable ultra-compact high-efficiency salt-to-sCO 2 heat exchanger for closed-loop Brayton power cycles based on corrosion resistant, high-strength, thermally conductive UHTC materials and novel designs enabled by additive manufacturing. The UHTC materials are also abrasion resistant so that they could be applicable to all three thermal carrier media pathways identified in the CSP Gen3 Roadmap.

36 MATERIALS SCIENCE↗

Analytical study on the suitability of using bentonite coated gravel as a landfill liner material

This study investigates the feasibility of using bentonite coated gravel (BCG) as a liner material for waste landfills. BCG has proven to be a very effective capping material/method for the remediation of contaminated sediments in aquatic environments. The concept of BCG is similar to that of peanuts/almonds covered with chocolate; each aggregate particle has been covered with the clayey material. Laboratory tests were aimed at evaluating regulated and non-regulated factors for liner materials, i.e., permeability and strength. Tests included X-ray diffraction, methylene blue absorption, compaction, free swelling, permeability, 1D consolidation, triaxial compression and cone penetration. The compactive efforts used for this study were the reduced Proctor, standard Proctor, intermediate Proctor, modified Proctor and super modified Proctor. The compactive energy corresponding to each effort, respectively, is as follows: 355.5, 592.3, 1196.3, 2693.3, and 5386.4 kJ/m{sup 3}. Results revealed that even though aggregate content represents 70% of the weight of the material, hydraulic conductivities as low as 6 x 10{sup -10} cm/s can be achieved when proper compactive efforts are used. Compressibility is very low for this material even at low (or no) compactive efforts. Results also demonstrated how higher compactive efforts can lower the permeability of BCG; however, over-compaction creates fractures in the aggregate core of BCG that could increase permeability. Moreover, higher compactive efforts create higher swelling pressures that could compromise the performance of a barrier constructed using BCG. As a result of this study, moderate compactive efforts, i.e., intermediate Proctor or modified Proctor, are recommended for constructing a BCG barrier. Using moderate compactive efforts, very low hydraulic conductivities, good workability and good trafficability are easily attainable.

36 MATERIALS SCIENCE↗

High-Entropy Borides under Extreme Environment of Pressures and Temperatures

The high-entropy transition metal borides containing a random distribution of five or more constituent metallic elements offer novel opportunities in designing materials that show crystalline phase stability, high strength, and thermal oxidation resistance under extreme conditions. We present a comprehensive theoretical and experimental investigation of prototypical high-entropy boride (HEB) materials such as (Hf, Mo, Nb, Ta, Ti)B2 and (Hf, Mo, Nb, Ta, Zr)B2 under extreme environments of pressures and temperatures. The theoretical tools include modeling elastic properties by special quasi-random structures that predict a bulk modulus of 288 GPa and a shear modulus of 215 GPa at ambient conditions. HEB samples were synthesized under high pressures and high temperatures and studied to 9.5 GPa and 2273 K in a large-volume pressure cell. The thermal equation of state measurement yielded a bulk modulus of 276 GPa, in excellent agreement with theory. The measured compressive yield strength by radial X-ray diffraction technique in a diamond anvil cell was 28 GPa at a pressure of 65 GPa, which is a significant fraction of the shear modulus at high pressures. The high compressive strength and phase stability of this material under high pressures and high temperatures make it an ideal candidate for application as a structural material in nuclear and aerospace fields.

36 MATERIALS SCIENCE↗

A theoretical approach for transient shock strengthening in high-energy-density laser compression experiments

In high-energy-density shock compression experiments, the desired state of compression is typically achieved by passing shock waves through a sequence of different materials. Here, a theoretical approach for transiently strengthening such shocks passing through interfaces of experimentally relevant impedance ratios is examined. A semi-analytical method based on characteristics analysis is used to solve the problem of a shock passing from one material to another through an intermediate region of non-uniform impedance; by appropriately designing this region, a greater shock strength can be achieved in the second material for a finite duration than in the absence of this region. When a shock passes into a material of higher impedance, the shock strengthening increases to a maximum before decreasing to an asymptotic value as the strength of the incident shock is increased. For shocks passing into materials of decreasing impedance, the shock strengthening increases monotonically as the strength of the incident shock is increased when the impedance ratio is above a critical threshold. Incorporating multiple intermediate materials can further increase the strength of the transmitted shock, with an exponential discretization of intermediate material impedances being the most effective distribution for strengthening strong shocks. The results suggest that up to 25% and 9% increases in pressure behind the leading shock can be achieved for materials of increasing and decreasing impedance, respectively. The technique is applied to the design of laser-driven dynamic compression experiments, and the results of the analysis are verified via comparison to simulations performed with the HYADES hydrodynamics code.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Tailoring the Properties of Chemically Recyclable Polyethylene‐Like Multiblock Polymers by Modulating the Branch Structure

Abstract Developing plastics that fill the need of polyolefins yet are more easily recyclable is a critical need to address the plastic waste crisis. However, most efforts in this vein have focused on high‐density polyethylene (PE), while many different types of PE exist. To create broadly sustainable PE with modular properties, we present the synthesis, characterization, and demonstration of materials applications for chemically recyclable PE‐like multiblock polymers prepared from distinct hard and soft blocks using ruthenium‐catalyzed dehydrogenative polymerization. By altering the branching pattern within the soft blocks, a series of PE‐like multiblock polymers were synthesized with tunable glass transition temperatures ( T g ) while maintaining consistent high melting temperatures ( T m ). A clear U‐shape trend between T g and mechanical properties was found, showcasing their potential as sustainable materials with tailored properties spanning commercial linear low‐density polyethylene (LLDPE) and low‐density polyethylene (LDPE). These materials offer adjustable adhesive strength to metal and demonstrate chemical recyclability and selective depolymerization in mixed plastic streams, promoting circularity and separation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Experimental and Modeling Studies on the Microstructures and Properties of Oxidized Aluminum Nitride Ceramic Substrates

Oxidation of aluminum nitride (AlN) ceramic substrates doped with 2 wt.% Y{sub 2}O{sub 3} was performed in air at temperatures ranging from 1000 to 1300 °C for various lengths of time. Microstructure, bending strength, and thermal conductivity of the oxidized AlN substrates were studied experimentally and also via mathematical models. The results show that the oxide layer formed on the AlN substrates is composed of α-Al{sub 2}O{sub 3} nanocrystallines and interconnected micropores. Longitudinal and transverse cracks are induced in the oxide layer under tensile and shear stresses, respectively. Intergranular oxidation of the AlN grains close to the oxide layer/AlN interface also occurs, leading to widening and cracking of the AlN grain boundaries. These processes result in the monotonous degradation of bending strength and thermal conductivity of the oxidized AlN substrates. Two mathematic models concerning these properties of the oxidized AlN substrates versus the oxide layer thickness were put forward. They fit well with the experimental results.

36 MATERIALS SCIENCE↗

Covalent integration of polymers and porous organic frameworks

Covalent integration of polymers and porous organic frameworks (POFs), including metal-organic frameworks (MOFs), covalent organic frameworks (COFs) and hydrogen-bonded organic frameworks (HOFs), represent a promising strategy for overcoming the existing limitations of traditional porous materials. This integration allows for the combination of the advantages of polymers, i.e., flexibility, processability and chemical versatility etc., and the superiority of POFs, like the structural integrity, tunable porosity and the high surface area, creating a type of hybrid materials. These resulting polymer-POF hybrid materials exhibit enhanced mechanical strength, chemical stability and functional diversity, thus opening up new opportunities for applications across a large variety of fields, such as gas separation, catalysis, biomedical applications, environmental remediation and energy storage. In this review, an overview of synthetic routes and strategies on how to covalently integrate different polymers with various POFs is discussed, especially with a particular focus on methods like polymerization within, on and among POF structures. To investigate the unique properties and functions of these resultant hybrid materials, the characterization techniques, including nuclear magnetic resonance spectroscopy (NMR), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), thermogravimetric analysis (TGA), transmission electron microscopy (TEM) and scanning electron microscopy (SEM), gas adsorption analysis (BET) and computational modeling and machine learning, are also presented. The ability of polymer-POFs to manipulate the pore environments at the molecular level affords these materials a wide range of applications, providing a versatile platform for future advancements in material science. Looking forward, to fully realize the potential of these hybrid materials, the authors highlight the scalability, green synthesis methods, and potential for stimuli-responsive polymer-POF materials as critical areas for future research.

Hossain, Md Amjad↗

Deuterium retention in advanced steels for fusion reactor structural application

Reduced activation ferritic-martensitic (RAFM) steels, castable nanostructured alloys (CNA), and oxide-dispersion-strengthened (ODS) steels have been developed for the fusion reactor structural application with improved mechanical properties and radiation resistance. However, the hydrogen isotope retention in these steels is not well understood. In this study, 10 keV D 2 implantation was performed on six steels, together with pure iron and T91 as references, at room temperature. Subsequent thermal desorption spectroscopy (TDS) measurements were carried out to investigate the deuterium retention. Possible deuterium trapping sites in the studied materials were discussed in coordination with available microstructural information. The results of this study indicated that ODS-steels have the largest deuterium retention, which is almost one order of magnitude higher than that of pure iron, ~6 times of RAFM, and 2–4 times of CNA steels. The difference in nanoparticles and grain/lath boundaries are primarily responsible for the different deuterium retention, while other trapping sites (e.g., vacancy clusters, dislocations, etc.) are present. Deuterium retention increases with increasing sink strength of the studied materials, although they are not linear correlated.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Packaging strategies for printed circuit board components. Volume I, materials & thermal stresses.

Decisions on material selections for electronics packaging can be quite complicated by the need to balance the criteria to withstand severe impacts yet survive deep thermal cycles intact. Many times, material choices are based on historical precedence perhaps ignorant of whether those initial choices were carefully investigated or whether the requirements on the new component match those of previous units. The goal of this program focuses on developing both increased intuition for generic packaging guidelines and computational methodologies for optimizing packaging in specific components. Initial efforts centered on characterization of classes of materials common to packaging strategies and computational analyses of stresses generated during thermal cycling to identify strengths and weaknesses of various material choices. Future studies will analyze the same example problems incorporating the effects of curing stresses as needed and analyzing dynamic loadings to compare trends with the quasi-static conclusions.

36 MATERIALS SCIENCE↗