Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “linear systems”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,585 records · Page 88

SCI Identification (SCIDNT) program user's guide

The computer program Linear SCIDNT which evaluates rotorcraft stability and control coefficients from flight or wind tunnel test data is described. It implements the maximum likelihood method to maximize the likelihood function of the parameters based on measured input/output time histories. Linear SCIDNT may be applied to systems modeled by linear constant-coefficient differential equations. This restriction in scope allows the application of several analytical results which simplify the computation and improve its efficiency over the general nonlinear case.

Source record↗

STAR adaptation of QR algorithm

The QR algorithm used on a serial computer and executed on the Control Data Corporation 6000 Computer was adapted to execute efficiently on the Control Data STAR-100 computer. How the scalar program was adapted for the STAR-100 and why these adaptations yielded an efficient STAR program is described. Program listings of the old scalar version and the vectorized SL/1 version are presented in the appendices. Execution times for the two versions applied to the same system of linear equations, are compared.

Shah, S. N.↗

Modal cost analysis for linear matrix-second-order systems

Reduced models and reduced controllers for systems governed by matrix-second-order differential equations are obtained by retaining those modes which make the largest contributions to quadratic control objectives. Such contributions, expressed in terms of modal data, used as mode truncation criteria, allow the statement of the specific control objectives to influence the early model reduction from very high order models which are available, for example, from finite element methods. The relative importance of damping, frequency, and eigenvector in the mode truncation decisions are made explicit for each of these control objectives: attitude control, vibration suppression and figure control. The paper also shows that using modal cost analysis (MCA) on the closed loop modes of the optimally controlled system allows the construction of reduced control policies which feedback only those closed loop modal coordinates which are most critical to the quadratic control performance criterion. In this way, the modes which should be controlled (and hence the modes which must be observable by choice of measurements), are deduced from truncations of the optimal controller.

Skelton, R. E.↗

Kramers-Kronig relationship between ultrasonic attenuation and phase velocity

Kramers-Kronig relations linking the attenuation and dispersion are presented for a linear acoustic system. These expressions are used as a starting point to derive approximate, nearly local expressions relating the ultrasonic attenuation at a specific frequency to the local frequency derivative of the phase velocity (i.e., dispersion). The validity of these approximate relationships is demonstrated in several acoustic systems exhibiting substantially different physical properties.

Odonnell, M.↗

Analysis of cracks emanating from a circular hole in unidirectional fiber reinforced composites, part 2

An analytical method is developed for cracks emanating from a circular hole in an off-axis unidirectional fiber-reinforced composite. The method which is formulated by using conservation laws of elasticity and fundamental relationships in anisotropic fracture mechanics, provides a convenient and accurate means to examine the complicated crack behavior, when used in conjunction with a suitable numerical scheme such as the finite element method. The formulation is eventually reduced to a system of linear algebraic equations of mixed-mode stress intensity factors. Fracture parameters, describing crack-tip deformation and fracture in the composite, are obtained explicitly. Effects of material anisotropy and crack/hole geometry are examined also. Of particular interest are the energy release rates associated with crack extension; their values are evaluated for various cases. Results show that mixed-mode stress intensity factors and energy release rates associated with the cracks emanating from a hole change very appreciably with fiber orientation in the composite. K sub 1 and G increase monotonically with increasing theta; but K sub 2 reaches its maximum at theta = 45 deg, and then decreases gradually as theta increases further.

Wang, S. S.↗

Map accuracy requirements: The cartographic potential of satellite image data

Cartographic products fall into a variety of classes: topographic maps that are concerned with planimetric information and elevations or heights; thematic maps, which might be used for geology, vegetation, water, or to display these subjects; digital elevation maps that would be produced from digital terrain data; and finally image maps. In terms of satellite applications, thematic maps and image maps are emphasized. The objectives are to consider, first, if resolution will be adequate for the identification of control and for the compilation of map products. Then, second, to define map accuracy standards and to determine the potential for meeting these standards with image data from the film camera, scanner and linear array systems of the 1980s.

Welch, R.↗

Hybrid state vector methods for structural dynamic and aeroelastic boundary value problems

A computational technique is developed that is suitable for performing preliminary design aeroelastic and structural dynamic analyses of large aspect ratio lifting surfaces. The method proves to be quite general and can be adapted to solving various two point boundary value problems. The solution method, which is applicable to both fixed and rotating wing configurations, is based upon a formulation of the structural equilibrium equations in terms of a hybrid state vector containing generalized force and displacement variables. A mixed variational formulation is presented that conveniently yields a useful form for these state vector differential equations. Solutions to these equations are obtained by employing an integrating matrix method. The application of an integrating matrix provides a discretization of the differential equations that only requires solutions of standard linear matrix systems. It is demonstrated that matrix partitioning can be used to reduce the order of the required solutions. Results are presented for several example problems in structural dynamics and aeroelasticity to verify the technique and to demonstrate its use. These problems examine various types of loading and boundary conditions and include aeroelastic analyses of lifting surfaces constructed from anisotropic composite materials.

Lehman, L. L.↗

Periodic orbits of the elliptic restricted problem for the Sun-Jupiter-Saturn system

A systematic approach to generate periodic orbits in the elliptic restricted problem of three bodies is introduced. The approach is based on (numerical) continuation from periodic orbits of the first and second kind in the circular restricted problem to periodic orbits in the elliptic restricted problem. Two families of periodic orbits of the elliptic restricted problem are found by this approach. The mass ratio of the primaries of these orbits is equal to that of the Sun-Jupiter system. The sidereal mean motions between the infinitesimal body and the smaller primary are in a 2:5 resonance, so as to approximate the Sun-Jupiter-Saturn system. The lineaar stabilities of these periodic orbits are studied as functions of the eccentricities of the primaries and of the infinitesimal body. The results show that both stable and unstable periodic orbits exist in the elliptic restricted problem that are close to the actual Sun-Jupiter-Saturn system. However, the periodic orbit closest to the actual Sun-Jupiter-Saturn system is (linearly) stable.

Kwok, J. H.↗

Numerical computation of exponential matrices using the Cayley-Hamilton theorem

A method for computing exponential matrices, which often arise naturally in the solution of systems of linear differential equations, is developed. An exponential matrix is generated as a linear combination of a finite number (equal to the matrix order) of matrices, the coefficients of which are scalar infinite sums. The method can be generalized to apply to any formal power series of matrices. Attention is focused upon the exponential function, and the matrix exponent is assumed tri-diagonal in form. In such cases, the terms in the coefficient infinite sums can be extracted, as recursion relations, from the characteristic polynomial of the matrix exponent. Two numerical examples are presented in some detail: (1) the three dimensional infinitesimal rotation rate matrix, which is skew symmetric, and (2) an N-dimensional tri-diagonal and symmetric finite difference matrix which arises in the numerical solution of the heat conduction partial differential equation. In the second example, the known eigenvalues and eigenvectors of the finite difference matrix permit an analytical solution for the exponential matrix, through the theory of diagonalization and similarity transformations, which is used for independent verification. The convergence properties of the scalar infinite summations are investigated for finite difference matrices of various orders up to ten, and it is found that the number of terms required for convergence increases slowly with the order of the matrix.

Walden, H.↗

Guaranteed robustness properties of multivariable, nonlinear, stochastic optimal regulators

The robustness of optimal regulators for nonlinear, deterministic and stochastic, multi-input dynamical systems is studied under the assumption that all state variables can be measured. It is shown that, under mild assumptions, such nonlinear regulators have a guaranteed infinite gain margin; moreover, they have a guaranteed 50 percent gain reduction margin and a 60 degree phase margin, in each feedback channel, provided that the system is linear in the control and the penalty to the control is quadratic, thus extending the well-known properties of LQ regulators to nonlinear optimal designs. These results are also valid for infinite horizon, average cost, stochastic optimal control problems.

Tsitsiklis, J. N.↗

M-step preconditioned conjugate gradient methods

Preconditioned conjugate gradient methods for solving sparse symmetric and positive finite systems of linear equations are described. Necessary and sufficient conditions are given for when these preconditioners can be used and an analysis of their effectiveness is given. Efficient computer implementations of these methods are discussed and results on the CYBER 203 and the Finite Element Machine under construction at NASA Langley Research Center are included.

Adams, L.↗

An M-step preconditioned conjugate gradient method for parallel computation

This paper describes a preconditioned conjugate gradient method that can be effectively implemented on both vector machines and parallel arrays to solve sparse symmetric and positive definite systems of linear equations. The implementation on the CYBER 203/205 and on the Finite Element Machine is discussed and results obtained using the method on these machines are given.

Adams, L.↗

Convergence and stability properties of minimal polynomial and reduced rank extrapolation algorithms

The minimal polynomial and reduced rank extrapolation algorithms are two acceleration of convergence methods for sequences of vectors. In a recent survey these methods were tested and compared with the scalar, vector, topological epsilon algorithms, and were observed to be more efficient than the latter. It was also observed that the two methods have similar convergence properties. The convergence and stability properties of these methods are analyzed and the performance of the acceleration methods when applied to a class of vector sequences that includes those sequences obtained from systems of linear equations by using matrix iterative methods is discussed.

Sidi, A.↗

Identification of large flexible structures mass/stiffness and damping from on-orbit experiments

Two methods for identifying the mass, damping and stiffness matrices of a linear vibrating system are presented. Both methods require the measurement of acceleration, velocity and displacement at various locations of the system. In the first method, the response of the system subjected to known forces is used while the second method employs the free vibration data. The unknown parameters are recovered through the standard least squares procedure. Numerical results are presented for several examples.

Hendricks, S. L.↗

Processing study of a polyimidesulfone adhesive

An adhesive bonding process cycle study was performed for a polyimidesulfone (PISO2) recently developed as a promising structural adhesive. The high molecular weight, linear aromatic system possesses properties which make it attractive as a processable, low-cost material for elevated temperature applications. The results of a study to better understand the parameters that affect the adhesive properties of the polymer for titanium alloy adherends are detailed. These include the tape preparation, the use of a primer, and press and simulated autoclave processing conditions. The polymer was characterized using Fourier Transform Infrared Spectroscopy, glass transition temperature determination, flow measurements, and weight loss measurements. The adhesive's strength determined by lap shear strength tests was used to evaluate the effects of the bonding process variations. Higher lap shear strengths were obtained at room temperature when a primer (PISO2) was used; however, the results were the same at 232 C (450 F) with or without a primer. The use of a vacuum (simulated autoclave cycle) during titanium bonding produced similar lap shear strengths to those specimens bonded without a vacuum.

Progar, D. J.↗

Effects of bearing deadbands on bearing loads and rotor stability

A generic model of a turbopump, simplified to bring out these effects is examined. This model demonstrates that bearing deadbands which are of the same order of magnitude or larger than the center-of-mass offset of a rotor due to mass imbalances cause significantly different dynamic behavior than would be expected of a linear, dynamical system. This fundamentally nonlinear behavior yields altered stability characteristics and altered bearing loading tendencies. It is shown that side forces can enhance system stability in the small, i.e., as long as the mass imbalance does not exceed some thresholds value or as long as no large, impulsive disturbances cause the motion to depart significantly from the region of stability. Limit cycles are investigated in this report and techniques for determining these limit cycles are developed. These limit cycles are the major source of bearing loading and appear in both synchronous and nonsynchronous forms. The synchronous limit cycles are driven by rotor imbalances. The nonsynchronous limit cycles (also called subsynchronous whirls) are self-excited and are the sources of instability.

Source record↗

Newton like: Minimal residual methods applied to transonic flow calculations

A computational technique for the solution of the full potential equation is presented. The method consists of outer and inner iterations. The outer iterate is based on a Newton like algorithm, and a preconditioned Minimal Residual method is used to seek an approximate solution of the system of linear equations arising at each inner iterate. The present iterative scheme is formulated so that the uncertainties and difficulties associated with many iterative techniques, namely the requirements of acceleration parameters and the treatment of additional boundary conditions for the intermediate variables, are eliminated. Numerical experiments based on the new method for transonic potential flows around the NACA 0012 airfoil at different Mach numbers and different angles of attack are presented, and these results are compared with those obtained by the Approximate Factorization technique. Extention to three dimensional flow calculations and application in finite element methods for fluid dynamics problems by the present method are also discussed. The Inexact Newton like method produces a smoother reduction in the residual norm, and the number of supersonic points and circulations are rapidly established as the number of iterations is increased.

Wong, Y. S.↗