SEARCH · Engineering Papers

Results for “flaps”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,585 records · Page 88

All sources NASA NTRS DOE OSTI

NASA NTRS1977

An experimental and analytical investigation of proprotor whirl flutter

The results of an experimental parametric investigation of whirl flutter are presented for a model consisting of a windmilling propeller-rotor, or proprotor, having blades with offset flapping hinges mounted on a rigid pylon with flexibility in pitch and yaw. The investigation was motivated by the need to establish a large data base from which to assess the predictability of whirl flutter for a proprotor since some question has been raised as to whether flutter in the forward whirl mode could be predicted with confidence. To provide the necessary data base, the parametric study included variation in the pylon pitch and yaw stiffnesses, flapping hinge offset, and blade kinematic pitch-flap coupling over a large range of advance ratios. Cases of forward whirl flutter and of backward whirl flutter are documented. Measured whirl flutter characteristics were shown to be in good agreement with predictions from two different linear stability analyses which employed simple, two dimensional, quasi-steady aerodynamics for the blade loading. On the basis of these results, it appears that proprotor whirl flutter, both forward and backward, can be predicted.

Kvaternik, R. G.↗

NASA NTRS1977

Improvement of maneuver aerodynamics by spanwise blowing

Spanwise blowing was used to test a generalized wind-tunnel model to investigate component concepts in order to provide improved maneuver characteristics for advanced fighter aircraft. Primary emphasis was placed on performance, stability, and control at high angles of attack and subsonic speeds. Test data were obtained in the Langley high speed 7 by 10 foot tunnel at free stream Mach numbers up to 0.50 for a range of model angles of attack, jet momentum coefficients, and leading and trailing edge flap deflection angles. Spanwise blowing on a 44 deg swept trapezoidal wing resulted in leading edge vortex enhancement with subsequent large vortex induced lift increments and drag polar improvements at the higher angles of attack. Small deflections of a leading edge flap delayed these lift and drag benefits to higher angles of attack. In addition, blowing was more effective at higher Mach numbers. Spanwise blowing in conjunction with a deflected trailing edge flap resulted in lift and drag benefits that exceeded the summation of the effects of each high lift device acting alone. Asymmetric blowing was an effective lateral control device at the higher angles of attack.

Erickson, G. E.↗

NASA NTRS1977

Aerodynamic characteristics of an F-8 aircraft configuration with a variable camber wing at Mach numbers from 1.5 to 2.0

A 0.1-scale model of an F-8 aircraft was tested over a range of Mach numbers from 1.5 to 2.0. Reynolds number of 4.12 million was based on wing mean-aerodynamic chord for angles of attack varying from -2 deg to +12 deg. The model was equipped with an advanced-technology-conformal-variable-camber wing (ATCVCW) having simple hinge flaps. Data were also obtained for the model equipped with the basic F-8 wing and conventional flaps. Model variables included aileron and wing trailing edge deflections and horizontal tail incidence. The ATCVCW configuration produced slight improvements in lift-curve slope, drag, and static longitudinal stability over that of the basic F-8 wing configuration. Flap effectiveness was essentially the same for both wings.

Boltz, F. W.↗

NASA NTRS1978

A critical evaluation of the predictions of the NASA-Lockheed multielement airfoil computer program

Theoretical predictions of several versions of the multielement airfoil computer program are evaluated. The computed results are compared with experimental high lift data of general aviation airfoils with a single trailing edge flap, and of airfoils with a leading edge flap and double slotted trailing edge flaps. Theoretical and experimental data include lift, pitching moment, profile drag and surface pressure distributions, boundary layer integral parameters, skin friction coefficients, and velocity profiles.

Brune, G. W.↗

NASA NTRS1976

Upper-surface-blowing flow-turning performance

Jet exhaust flow-turning characteristics were determined for systematic variations in upper-surface blowing exhaust nozzles and trailing-edge flap configuration variables from experimental wind-off (static) flow studies. For conditions with parallel flow exhausting from the nozzle, jet height (as indicated by nozzle exit height) and flap radius were found to be the most important parameters relating to flow turning. Nonparallel flow from the nozzle, as obtained from an internal roof angle and/or side spread angle, had a large favorable effect on flow turning. Comparisons made between static turning results and wind tunnel aerodynamic studies of identical configurations indicated that static flow-turning results can be indicative of wind-on powered lift performance for both good and poor nozzle-flap combinations but, for marginal designs, can lead to overly optimistic assessment of powered lift potential.

Sleeman, W. C., Jr.↗

NASA NTRS1976

Results of static tests of a 1/4 scale model of the Boeing YC-14 powered-lift system

One quarter scale static ground tests of the Boeing YC-14 powered lift system were conducted for correlation with full scale test results. The 1/4 scale model utilized a JT-15D turbofan engine to represent the CF6-50D engine employed on the YC-14 advanced medium STOL transport prototype aircraft. The tests included evaluation of static turning performance, static surface pressure and temperature distributions, fluctuating loads, and accelerations of portions of the wing, flaps, and fuselage. Results are presented for the landing flap configuration over an appropriate range of fan pressure ratio as affected by several variables including ground height and vortex generator modifications. Static turning angles of the order of 60 deg were obtained. The highest surface pressures and temperatures were concentrated over the upper surface of the flaps in the region immediately aft of the upper surface blown nozzle.

Hassell, J. L., Jr.↗

NASA NTRS1976

Distributed upper-surface blowing concept

A low speed investigation was conducted in the Langley V/STOL tunnel to determine the powered lift aerodynamic performance of a distributed upper surface blown propulsive lift transport model. The model used blowing slots across the span of the wing to produce a thin jet efflux near the leading edge and at the knee of the trailing edge flap (internally blown jet flap). Results indicate that these concepts have both good propulsive related lift and low drag due to lift characteristics because of uniform spanwise propulsive thrust. The leading edge blowing concept provides low speed lift characteristics which are competitive with the flap-hinge-line blowing concept and does not require additional leading edge treatment for prevention of abrupt stall.

Fournier, P. G.↗

NASA NTRS1978

Airframe noise of the DC-9-31

Airframe noise measurements are reported for the DC-9-31 aircraft flown at several speeds and with a number of flap, landing gear, and slat extension configurations. The data are corrected for wind effects, atmospheric attenuation, and spherical divergence, and are normalized to a 1 meter acoustic range. The sound pressure levels are found to vary approximately as the fifth power of flight velocity. Both lift and drag dipoles exist as a significant part of the airframe noise. The sideline data imply that a significant side-force dipole exists only for the flap- and gear-down configurations; for others, the data imply the existence of only the lift and drag dipoles. The data are compared with airframe noise predictions using the drag element and the data analysis methods. Although some of the predictions are good, further work is needed to refine the methods, particularly for the flap- and gear-down configurations.

Bauer, A. B.↗

NASA NTRS1976

Theoretical Study of Multicyclic Control of a Controllable Twist Rotor

Analytical studies were performed to ascertain the feasibility of reducing helicopter rotor induced 4/rev vibratory forces by means of multicyclic flap control input on a dual control, four bladed rotor system. The dual control consisted of a primary inboard pitch horn blade control and a secondary outboard flap control. Flap control was put in at frequencies greater than the rotor rotational speed.

Lemnios, A. Z.↗

NASA NTRS1979

Fluctuating loads measured on an over-the-wing supersonic jet model

Fluctuating pressure loads on the wing and flap of an over-the-wing supersonic jet model were measured. The model was tested statically and at a Mach number of 0.1 in a small free jet to simulate forward speed. Test parameters were impingement angle, nozzle height, and flap deflection. Load levels as high as 170 db were measured at the center of the impingement region during static tests. Forward speed reduced the loading about 1 db. Load level increased with increasing impingement angle and decreasing nozzle height above the wing. The effect of flap deflection was small. When scaled to full-size aircraft conditions, the maximum amplitude of the one-third-octave fluctuating pressure spectra was about 154 db at about 160 Hz. Maximum load level occurred near the intersection of the nozzle center line with the impinged surface. Downstream of the maximum the fluctuating pressure is inversely proportional to the distance downstream of the nozzle.

Willis, C. M.↗

NASA NTRS1979

A simplified rotor system mathematical model for piloted flight dynamics simulation

The model was developed for real-time pilot-in-the-loop investigation of helicopter flying qualities. The mathematical model included the tip-path plane dynamics and several primary rotor design parameters, such as flapping hinge restraint, flapping hinge offset, blade Lock number, and pitch-flap coupling. The model was used in several exploratory studies of the flying qualities of helicopters with a variety of rotor systems. The basic assumptions used and the major steps involved in the development of the set of equations listed are described. The equations consisted of the tip-path plane dynamic equation, the equations for the main rotor forces and moments, and the equation for control phasing required to achieve decoupling in pitch and roll due to cyclic inputs.

Chen, R. T. N.↗

NASA NTRS1977

Two-dimensional wind-tunnel tests of a NASA supercritical airfoil with various high-lift systems. Volume 1: Data analysis

High-lift systems for a NASA, 9.3%, method for calculating the viscous flow about two-dimensional multicomponent airfoils was evaluated by comparing its predictions with test data. High-lift systems derived from supercritical airfoils were compared in terms of performance to high-lift systems derived from conventional airfoils. The high-lift systems for the supercritical airfoil were designed to achieve maximum lift and consisted of: a single-slotted flap; a double-slotted flap and a leading-edge slat; and a triple-slotted flap and a leading-edge slat. Agreement between theoretical predictions and experimental results are also discussed.

Omar, E.↗

NASA NTRS1980

Phase 1 wind tunnel tests of the J-97 powered, external augmentor V/STOL model

Test results are presented for a large scale, external augmentor V/STOL model in a 40 ft by 80 ft wind tunnel. The model was powered by a GE J97 engine and featured longitudinal ejectors alongside and external to the fuselage together with an augmentor flap on the low aspect ratio, double-delta wing. A static thrust augmentation ratio of 1.60 was measured for the fuselage augmentor at a nozzle pressure ratio of 3.0 and a nozzle exhaust gas temperature of 700 C. At forward speed the model showed a strong positive lift interference due to the augmentor flap, and a marked absence of negative lift interference due to the fuselage augmentor jet system. The nose-up moment of the fuselage augmentor inlet flow was approximately cancelled by a 60 deg deflection of the augmentor flap. An assessment of the thrust and drag components to allow the prediction of transition performance of aircraft designs based on the present conceptual model was made. Lateral tests showed strong but well ordered effects of power.

Garland, D. B.↗

NASA NTRS1980

Noise generation by a lifting wing/flap combination at Reynolds numbers to 2.8 x 10 to the 6th

Measurements relating to the noise source location and intensity within various frequency bands were made for an 0.75 m-chord wing/flap model installed in the Ames 7 x 10-foot wind tunnel. A directional microphone system, located outside the open-wall tunnel was scanned in a two-dimensional array of aiming points about the positive-pressure side of the model to determine the principal locations of noise production, and the intensity of each of these. It was found for the case of the flaps being differentially deflected (0 deg, 35 deg) at the half-span station that noise production was concentrated in the immediate region of the resultant surface discontinuity. For equal deflection of the halves (0 deg, 0 deg or 35 deg, 35 deg), noise was produced uniformly along the length of the gap between the wing and the flap. Simulated flap-mounting brackets generated considerable noise in certain cases, but reduced the noise in others. Trailing edge noise did not appear to be important in comparison with other sources.

Kendall, J. M.↗

NASA NTRS1981

Description of recent changes in the Langley 6- by 28-inch transonic tunnel

Calibrations were obtained in the Langley 6 by 28-inch transonic tunnel with newly installed controllable reentry flaps and test section floor and ceiling. Using available theory, the top and bottom slotted walls were redesigned for minimum wind tunnel interference errors of blockage and stream-line curvature. To minimize Mach number gradients along the tunnel axis downstream of the model, controllable flaps were installed to regulate the flow reentering the test section through the slotted walls. The flap setting is independent of stagnation pressure and varies only with Mach number. The freestream Mach number is determined from the pressrue measured at a station 66.04 cm upstream of the model station. The model has no significant influence on the vertical Mach number distribution at this station. This method of Mach number determination appears to be more accurate than one using the plenum pressure.

Sewall, W. G.↗

NASA NTRS1981

Unpowered Aerodynamic Characteristics of a 15-Percent Scale Model of a Twin-Engine Commuter Aircraft

An experimental investigation was conducted in the Ames 12-Foot Pressure Wind Tunnel to determine the unpowered aerodynamic characteristics of a 15-percent-scale model of a twin-engine commuter aircraft. Model longitudinal aerodynamic characteristics were examined at discrete flap deflections for various angle-of-attack and wind-tunnel-velocity ranges with the empennage on and off. Data are presented for the basic model configuration consisting of the fuselage, wing, basic wing leading edge, double slotted flaps, midengine nacelles, and empennage. Other configurations tested include a particle-span drooped leading edge (dropped outboard of the engine nacelles), a full-span drooped leading edge, low- and high-mounted engine nacelles, and a single-slotted flap. An evaluation was made of the model mounting system by comparing data obtained with the model mounted conventionally on the wind-tunnel model-support struts and the model inverted.

Morgan, D. G.↗

NASA NTRS1981

Some applications of aerodynamic formulations to problems in aircraft dynamics

Two applications of mathematical modeling to aerodynamic problems are cussed. The first application is an investigation of the capacity of a nonlinear aerodynamic mathematical model to describe the aerodynamic reactions on an airfoil with a deflecting flap in transonic flow. Flow field computational methods are used to evaluate the nonlinear, unsteady aerodynamic data in terms of characteristic motions called for by the model. Histories of unconstrained motions of the flap are generated from the flap equations of motion, with the aerodynamic reactions specified by the mathematical model. In the second application wing rock is investigated. The most recent model accommodates experimental results wing rock by admitting the existence of aerodynamic hysteresis in the variation of the steady state rolling moment coefficient with roll angle is described.

Schiff, L. B.↗

NASA NTRS1980

Helicopter theory

A comprehensive presentation is made of the engineering analysis methods used in the design, development and evaluation of helicopters. After an introduction covering the fundamentals of helicopter rotors, configuration and operation, rotary wing history, and the analytical notation used in the text, the following topics are discussed: (1) vertical flight, including momentum, blade element and vortex theories, induced power, vertical drag and ground effect; (2) forward flight, including in addition to momentum and vortex theory for this mode such phenomena as rotor flapping and its higher harmonics, tip loss and root cutout, compressibility and pitch-flap coupling; (3) hover and forward flight performance assessment; (4) helicopter rotor design; (5) rotary wing aerodynamics; (6) rotary wing structural dynamics, including flutter, flap-lag dynamics ground resonance and vibration and loads; (7) helicopter aeroelasticity; (8) stability and control (flying qualities); (9) stall; and (10) noise.

Johnson, W.↗