Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “finite”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,585 records · Page 88

Finite element thermal-structural analyses of a cable-stiffened orbiting antenna

Finite element thermal-structural analyses of a cable-stiffened orbiting antenna are presented. The determination of prestresses in the antenna is described first. Heating and thermal analyses for orbiting space structures are then discussed briefly. Structural deformations and stresses are presented for three finite element structural analysis approaches: (1) small deflections, (2) stress-stiffening, and (3) large deflections. The accuracy of the three analysis approaches is evaluated for the orbiting antenna at different prestress levels.

Thornton, E. A.↗

Finite element engine blade structural optimization

The Structural Tailoring of Engine Blades (STAEBL) computer program was developed to perform engine fan blade numerical optimizations. These blade optimizations seek a minimum weight or cost design that satisfies realistic blade design constraints, by tuning one to twenty design variables. The STAEBL system has been generalized to include both fan and compressor blade numerical optimizations. The system analyses have been significantly improved through the inclusion of an efficient plate finite element analysis for blade stress and frequency determinations. Additionally, a finite element based approximate severe foreign object damage (FOD) analysis has been included. The new FOD analysis gives very accurate estimates of the full nonlinear bird ingestion solution. Optimizations of fan and compressor blades have been performed using the system, showing significant cost and weight reductions, while comparing very favorably with refined design validation procedures.

Brown, K. W.↗

Constitutive modeling and computational implementation for finite strain plasticity

This paper describes a simple alternate approach to the difficult problem of modeling material behavior. Starting from a general representation for a rate-tpe constitutive equation, it is shown by example how sets of test data may be used to derive restrictions on the scalar functions appearing in the representation. It is not possible to determine these functions from experimental data, but the aforementioned restrictions serve as a guide in their eventual definition. The implications are examined for hypo-elastic, isotropically hardening plastic, and kinematically hardening plastic materials. A simple model for the evolution of the 'back-stress,' in a kinematic-hardening plasticity theory, that is entirely analogous to a hypoelastic stress-strain relation is postulated and examined in detail in modeling finitely plastic tension-torsion test. The implementation of rate-type material models in finite element algorithms is also discussed.

Reed, K. W.↗

Finite element methods for high speed flows

An explicit finite element based solution procedure for solving the equations of compressible viscous high speed flow is presented. The method uses domain splitting to advance the solution with different timesteps on different portions of the mesh. For steady inviscid flows, adaptive mesh refinement procedures are successfully employed to enhance the definition of discontinuities. Preliminary ideas on the application of adaptive mesh refinement to the solution of problems involving steady viscous flow are presented. Sample timings are given for the performance of the finite element code on modern supercomputers.

Loehner, R.↗

Finite difference analysis of torsional vibrations of pretwisted, rotating, cantilever beams with effects of warping

Theoretical natural frequencies of the first three modes of torsional vibration of pretwisted, rotating cantilever beams are determined for various thickness and aspect ratios. Conclusions concerning individual and collective effects of warping, pretwist, tension-torsion coupling and tennis racket effect (twist-rotational coupling) terms on the natural frequencies are drawn from numerical results obtained by using a finite difference procedure with first order central differences. The relative importance of structural warping, inertial warping, pretwist, tension-torsion and twist-rotational coupling terms is discussed for various rotational speeds. The accuracy of results obtained by using the finite difference approach is verified by a comparison with the exact solution for specialized simple cases of the equation of motion used in this paper.

Subrahmanyam, K. B.↗

Developments in the simulation of separated flows using finite difference methods

Compressible viscous flow simulation using finite difference Navier-Stokes and viscous-inviscid interaction methods is described. Recent developments are reviewed that significantly improve the computational efficiency of approximately factored implicit Navier-Stokes algorithms. Compared to Navier-Stokes codes, modern viscous-inviscid interaction codes are more computationally efficient, but have restricted application and are more complicated to program. Therefore, less efficient but more general viscous-inviscid interaction methods are investigated that use forcing functions instead of boundary condition matching, and a simple, direct/inverse, three-dimensional, finite-difference, boundary layer code is presented.

Steger, J. L.↗

Nonlinear shock acceleration. III - Finite wave velocity, wave pressure, and entropy generation via wave damping

The nonlinear theory of shock acceleration developed in earlier papers, which treated the waves as being completely frozen into the fluid, is generalized to include wave dynamics. In the limit where damping keeps the wave amplitude small, it is found that a finite phase velocity (V sub ph) of the scattering waves through the background fluid, tempers the acceleration generated by high Mach number shocks. Asymptotic spectra proportional to 1/E sq are possible only when the ratio of wave velocity to shock velocity is less than 0.13. For a given asymptotic spectrum, the efficiency of relativistic particle production is found to be practically independent of the value of V sub ph, so that earlier results concerning its value remain valid for finite V sub ph. In the limit where there is no wave damping, it is shown that for modest Alfven Mach numbers, approximately greater than 4 and less than 6, the magnetic field is amplified by the energetic particles to the point of being in rough equipartition with them, as models of synchrotron emission frequently take the field to be. In this case, the disordering and amplification of field energy may play a major role in the shock transition.

Eichler, D.↗

Strain energy release rate determination of stress intensity factors by finite element methods

The stiffness derivative finite element technique is used to determine the Mode I stress intensity factors for three-crack configurations. The geometries examined include the double edge notch, single edge notch, and the center crack. The results indicate that when the specified guidelines of the Stiffness Derivative Method are used, a high degree of accuracy can be achieved with an optimized, relatively coarse finite element mesh composed of standard, four-node, plane strain, quadrilateral elements. The numerically generated solutions, when compared with analytical ones, yield results within 0.001 percent of each other for the double edge crack, 0.858 percent for the single edge crack, and 2.021 percent for the center crack.

Walsh, R. M., Jr.↗

Exact finite difference schemes for the non-linear unidirectional wave equation

Attention is given to the construction of exact finite difference schemes for the nonlinear unidirectional wave equation that describes the nonlinear propagation of a wave motion in the positive x-direction. The schemes constructed for these equations are compared with those obtained by using the usual procedures of numerical analysis. It is noted that the order of the exact finite difference models is equal to the order of the differential equation.

Mickens, R. E.↗

Application of High Order Acoustic Finite Elements to Transmission Losses and Enclosure Problems

A family of acoustic finite elements was developed based on C continuity (acoustic pressure being the nodal variable) and the no-flow condition. The family include triangular, quadrilateral and hexahedral isoparametric elements with linear quadratic and cubic variation in modelling and distortion. Of greatest use in problems with irregular boundaries are the cubic isoparametric elements: the 32 node hexahedral element for three-dimensional systems; and the twelve node quadrilateral and ten node triangular elements for two-dimensional/axisymmetric applications. These elements were applied to problems involving cavity resonances, transmission loss in silencers and the study of end effects, using a Floating Point Systems 164 attached array processor accessed through an Amdahl 5860 mainframe. The elements are presently being used to study the end effects associated with duct terminations within finite enclosures. The transmission losses with various silencers and sidebranches in ducts is also being studied using the same elements.

Craggs, A.↗

Effect of measured material properties on the finite element analysis of an OH-58 composite tail boom

A static and dynamic finite element analysis is conducted on a U.S. Army OH-58 composite tail boom and compared with test data. The tail boom is a filament-wound graphite/epoxy monocoque structure. The structural design of the composite tail boom skin is based on 50-percent graphite fiber volume. However, material tests on representative samples of the tail boom skin reveal that the graphite fiber-volume fraction varied from 44.6 to 49.3 percent. To determine the effect of using measured material properties, static and dynamic finite element analyses are conducted for three fiber-volume conditions of 45, 48, and 50 percent. The static and dynamic model with the 45-percent fiber-volume graphite skins gives the closest agreement with test data.

Bowman, L. M.↗

A VLSI single chip 8-bit finite field multiplier

A Very Large Scale Integration (VLSI) architecture and layout for an 8-bit finite field multiplier is described. The algorithm used in this design was developed by Massey and Omura. A normal basis representation of finite field elements is used to reduce the multiplication complexity. It is shown that a drastic improvement was achieved in this design. This multiplier will be used intensively in the implementation of an 8-bit Reed-Solomon decoder and in many other related projects.

Deutsch, L. J.↗

Three-dimensional elastic-plastic finite-element analysis of fatigue crack propagation

Fatigue cracks are a major problem in designing structures subjected to cyclic loading. Cracks frequently occur in structures such as aircraft and spacecraft. The inspection intervals of many aircraft structures are based on crack-propagation lives. Therefore, improved prediction of propagation lives under flight-load conditions (variable-amplitude loading) are needed to provide more realistic design criteria for these structures. The main thrust was to develop a three-dimensional, nonlinear, elastic-plastic, finite element program capable of extending a crack and changing boundary conditions for the model under consideration. The finite-element model is composed of 8-noded (linear-strain) isoparametric elements. In the analysis, the material is assumed to be elastic-perfectly plastic. The cycle stress-strain curve for the material is shown Zienkiewicz's initial-stress method, von Mises's yield criterion, and Drucker's normality condition under small-strain assumptions are used to account for plasticity. The three-dimensional analysis is capable of extending the crack and changing boundary conditions under cyclic loading.

Goglia, G. L.↗

Planning, creating and documenting a NASTRAN finite element model of a modern helicopter

Mathematical models based on the finite element method of structural analysis as embodied in the NASTRAN computer code are widely used by the helicopter industry to calculate static internal loads and vibration of airframe structure. The internal loads are routinely used for sizing structural members. The vibration predictions are not yet relied on during design. NASA's Langley Research Center sponsored a program to conduct an application of the finite element method with emphasis on predicting structural vibration. The Army/Boeing CH-47D helicopter was used as the modeling subject. The objective was to engender the needed trust in vibration predictions using these models and establish a body of modeling guides which would enable confident future prediction of airframe vibration as part of the regular design process.

Gabal, R.↗

An analysis of cross-coupling of a multicomponent jet engine test stand using finite element modeling techniques

A two axis thrust measuring system was analyzed by using a finite a element computer program to determine the sensitivities of the thrust vectoring nozzle system to misalignment of the load cells and applied loads, and the stiffness of the structural members. Three models were evaluated: (1) the basic measuring element and its internal calibration load cells; (2) the basic measuring element and its external load calibration equipment; and (3) the basic measuring element, external calibration load frame and the altitude facility support structure. Alignment of calibration loads was the greatest source of error for multiaxis thrust measuring systems. Uniform increases or decreases in stiffness of the members, which might be caused by the selection of the materials, have little effect on the accuracy of the measurements. It is found that the POLO-FINITE program is a viable tool for designing and analyzing multiaxis thrust measurement systems. The response of the test stand to step inputs that might be encountered with thrust vectoring tests was determined. The dynamic analysis show a potential problem for measuring the dynamic response characteristics of thrust vectoring systems because of the inherently light damping of the test stand.

Schweikhard, W. G.↗

Cyclic creep analysis from elastic finite-element solutions

A uniaxial approach was developed for calculating cyclic creep and stress relaxation at the critical location of a structure subjected to cyclic thermomechanical loading. This approach was incorporated into a simplified analytical procedure for predicting the stress-strain history at a crack initiation site for life prediction purposes. An elastic finite-element solution for the problem was used as input for the simplified procedure. The creep analysis includes a self-adaptive time incrementing scheme. Cumulative creep is the sum of the initial creep, the recovery from the stress relaxation and the incremental creep. The simplified analysis was exercised for four cases involving a benchmark notched plate problem. Comparisons were made with elastic-plastic-creep solutions for these cases using the MARC nonlinear finite-element computer code.

Kaufman, A.↗

Thermodynamic evaluation of transonic compressor rotors using the finite volume approach

The finite volume explicit time marching method was refined and improved. Previously, extension had been made to the finite volume method to improve the accuracy of the calculation of total pressure in inviscid flow, extend the method to allow the calculation of laminar and turbulent boundary layers in internal flows, and improve the shock capturing properties of the method by introducing a Mach number dependent interpolation scheme for the pressure used in the calculating the density. The current work extends these developments by using the new pressure interpolation scheme in two dimensional viscous calculations, including a more complete description of the viscous stresses, introducing a criteria for the transverse upwind differencing which is a function of the ratio of transverse and streamwise mass fluxes, and allowing the calculation of internal flow where boundary layers are present on both walls of the duct. The manner in which the viscous stresses are evaluated in the nonorthogonal, nonuniform grid is detailed. The convergence is investigated and results for calculations of laminar flow in a converging duct are presented. Results for calculations of transonic flow in a converging-diverging nozzle are presented and the results are compared with Sajben's measurements and calculations by others.

Nicholson, S.↗

Comparative efficiency of finite, boundary and hybrid element methods in elastostatics

The comparative computational efficiencies of the finite element (FEM), boundary element (BEM), and hybrid boundary element-finite element (HBFEM) analysis techniques are evaluated for representative bounded domain interior and unbounded domain exterior problems in elastostatics. Computational efficiency is carefully defined in this study as the computer time required to attain a specified level of solution accuracy. The study found the FEM superior to the BEM for the interior problem, while the reverse was true for the exterior problem. The hybrid analysis technique was found to be comparable or superior to both the FEM and BEM for both the interior and exterior problems.

Schwartz, C. W.↗