Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “feature design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,585 records · Page 88

A low energy beam transport system for proton beam

A low energy beam transport (LEBT) system has been built for a compact pulsed hadron source (CPHS) at Tsinghua University in China. The LEBT, consisting of two solenoids and three short-drift sections, transports a pulsed proton beam of 60 mA of energy of 50 keV to the entrance of a radio frequency quadrupole (RFQ). Measurement has shown a normalized RMS beam emittance less than 0.2 {pi} mm mrad at the end of the LEBT. Beam simulations were carried out to compare with the measurement and are in good agreement. Based on the successful CPHS LEBT development, a new LEBT for a China ADS projector has been designed. The features of the new design, including a beam chopper and beam simulations of the LEBT are presented and discussed along with CPHS LEBT development in this article.

43 PARTICLE ACCELERATORS↗

QMI: Rising to the Space Station Design Challenge

The Quench Module Insert (QMI) materials processing furnace is being designed to operate for 8000 hours over four years on the International Space Station (ISS) as part of the first Materials Science Research Rack (MSRR-1) of the Materials Science Research Facility (MSRF). The Bridgman-type furnace is being built for the directional solidification processing of metals and alloys in the microgravity environment of space. Most notably it will be used for processing aluminum and related alloys. Designing for the space station environment presents intriguing design challenges in the form of a ten-year life requirement coupled with both limited opportunities for maintenance and resource constraints in the form of limited power and space. The long life requirement has driven the design of several features in the furnace, including the design of the heater core, the selection and placement of the thermocouples, overall performance monitoring, and the design of the chill block. The power and space limitations have been addressed through a compact furnace design using efficient vacuum insulation. Details on these design features, as well as development test performance results to date, are presented.

Carswell, W. E.↗

Development of an Air Transport Type A Fissile Package

This paper presents the summary of testing by the Savannah River National Laboratory (SRNL) to support development of a light weight (<140 lbs) air transport qualified Type A Fissile Packaging. The package design incorporates features and materials specifically designed to minimize packaging weight. The light weight package is being designed to provide confinement to the contents when subjected to the normal and hypothetical conditions required of an air transportable Type A Fissile radioactive material shipping package. The objective of these tests was to provide design input to the final design for the LORX Type A Fissile Air Transport Packaging when subjected to the performance requirements of the drop, crush and puncture probe test of 10CFR71. The post test evaluation of the prototype packages indicates that all of the tested designs would satisfactorily confine the content within the packaging. The differences in the performance of the prototypes varied significantly depending on the core materials and their relative densities. Information gathered from these tests is being used to develop the final design for the Department of Homeland Security.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Innovative Safety Ideas for Fusion Experimental Machines

Throughout the early stages of design of fusion experimental devices, such as ITER, safety experts have worked with designers to incorporate safety features into the design. Recent efforts have focused on passive safety features. Although designs of near-term fusion machines may appear consistent with expected regulatory requirements, the safety characteristics can potentially be more attractive. Here, a variety of suggestions that appear promising in terms of improving safety are given. These include new concepts, innovative technologies, further support of past concepts, and possible modification to operating scenarios. Some technical discussion on the feasibility of the proposals is provided. The ideas are generally conceptual at this stage and require further assessment and development work. However, each has the potential for enhancing the safety of experimental devices.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Griffin: A MOOSE-based reactor physics application for multiphysics simulation of advanced nuclear reactors

Griffin is a Multiphysics Object-Oriented Simulation Environment (MOOSE) based reactor physics application for multiphysics simulations of advanced reactor designs jointly developed by Idaho National Laboratory and Argonne National Laboratory. This paper summarizes the motivation, significance, architecture, design, and features of Griffin. Griffin offers flexible and extensible features to address the challenges associated with advanced reactor designs. These features range from fundamental particle transport to specific reactor physics tasks. The features cover a wide range including on-the-fly and traditional two-step cross-section generation methods, steady-state and transient transport solvers suitable for both heterogeneous and homogeneous models, high-fidelity depletion where thousands of isotopes can be tracked and low-fidelity depletion characterized by burnup, etc. The most fundamental aspect that sets Griffin apart from other reactor analysis codes is that it is developed based on the MOOSE framework. A modular development approach is strongly enforced, with multiphysics being an essential element considered since the beginning of Griffin’s development. Griffin links various MOOSE physics modules and couples to other MOOSE-based applications and non-MOOSE-based applications for multiphyiscs simulations. Griffin includes three modules: ISOXML for preparing and managing multigroup cross sections, radiation transport for solving the neutron transport equation, and reactor analysis for user-oriented reactor physics analysis functionalities. Griffin uses various finite element methods for spatial discretization, multigroup approximation for energy discretization and discrete ordinates method, spherical harmonics expansion method, and diffusion approximation for streaming direction discretization to solve the neutron transport equation. Griffin’s flexibility is evidenced through Griffin’s various applications to fast reactor, high-temperature reactor, pebble bed reactor, molten salt reactor, and microreactor designs. Griffin development follows the software quality assurance procedure for MOOSE-based applications and with software requirements consistent with the ASME NQA-1 standard. Griffin has been adopted into the reactor analysis system for the U.S. NRC and is in use at U.S. companies, universities and national laboratories.

97 MATHEMATICS AND COMPUTING↗

Domestic Safeguards Material Control and Accountancy Considerations for Molten Salt Reactors

Molten salt reactors (MSRs) are a class of nuclear reactor designs with features and operational characteristics that vary significantly more than the class of light water reactors (LWRs). MSR design concepts can be broadly categorized as solid-fueled reactors with molten salt as the coolant, liquid-fueled reactors with fuel dissolved in molten salt coolant and liquid-fueled reactors with fuel dissolved in molten salt that is contained in distinct fuel tubes with a nonfissile coolant. Proposed MSR concepts include features that are specific to each design. MSR concepts vary widely across these design features, including the physical, chemical, and isotopic composition of fresh and irradiated fuel. Operational neutron energy spectrums and breeding ratios also vary significantly across design concepts. Some concepts are burner reactors designed to transmute the spent nuclear fuel from LWRs or pressurized heavy water reactors (PHWRs), while others are breeder reactors designed to breed fissile 233 U from naturally occurring fertile 232 Th. Some MSR concepts are designed to be a part of a once-through fuel cycle, while others involve chemical separation. Those that include plans to recycle the fuel differ by whether the chemical processing would be done onsite, as a process connected to the fuel salt itself, or offsite at a reprocessing facility similar to how LWR or PHWR spent fuel is reprocessed in some countries. Each overall design concept contains various aspects of each of these features to produce a unique facility

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

High temperature, high intensity solar array

The solar array for the Venus Radar Mapper mission will operate in the high temperature, high intensity conditions of a low Venus orbit environment. To fulfill the performance requirements in this environment at minimum cost and mass while maximizing power density and packing factor on the panel surface, several features were introduced into the design. These features included the use of optical surface reflectors (OSR's) to reduce the operating temperature; new adhesives for conductive bonding of OSR's to avoid electrostatic discharges; custom-designed large area cells and novel shunt diode circuit and panel power harness configurations.

Smith, B. S.↗

Maintaining Hubble Space Telescope performance through in-orbit servicing

The HST system design is described as well as the in-orbit servicing program. In order to verify the feasibility and the design of the HST servicing features, a design verification program, which included 1-g tests and 0-g underwater simulations, was carried out. The major elements of the space support equipment, including the flight support system, the orbital replacement unit carrier, and the solar array carrier, are addressed in detail.

Cuviello, Michael J.↗

Conceptual Fuel Element Design Candidates for Conversion of High Flux Isotope Reactor with Low-Enriched Uranium Silicide Dispersion Fuel

Engineering design studies are underway to assess the feasibility of converting the High Flux Isotope Reactor (HFIR) to operate with low-enriched uranium (LEU) silicide dispersion (U3Si2-Al) fuel. These studies are supported by the U.S. Department of Energy National Nuclear Security Administration’s Office of Material Management and Minimization. A systematic approach employing neutronic and thermal-hydraulic analyses have been performed with the ORNL Shift and HFIR Steady State Heat Transfer Code tools, respectively, to predict reactor performance and thermal safety margins for proposed LEU3Si2-Al fuel designs. The design process was initiated by generating an optimized design with fabrication features identified from previous studies that result in excellent performance and safety metrics. The approach continued by substituting a single fabrication feature anticipated to be difficult to manufacture with another feature expected to perform an analogous function to that of the removed feature. Four conceptual fuel element design candidates, with various fabrication features, for conversion of HFIR with 4.8 gU/cm3 LEU3Si2-Al fuel have been generated and shown to meet pre-defined performance and safety metrics. Results to date indicate that HFIR could convert with the subject fuel system and meet performance and safety requirements if, among other considerations, fabrication of the specific design features are demonstrated and qualification of the fuel is complete under HFIR-specific conditions.

Chandler, David↗

Reusable Solid Rocket Motor - Accomplishments, Lessons, and a Culture of Success

The Reusable Solid Rocket Motor represents the largest solid rocket motor ever flown and the only human rated solid motor. Each Reusable Solid Rocket Motor (RSRM) provides approximately 3-million lb of thrust to lift the integrated Space Shuttle vehicle from the launch pad. The motors burn out approximately 2 minutes later, separate from the vehicle and are recovered and refurbished. The size of the motor and the need for high reliability were challenges. Thrust shaping, via shaping of the propellant grain, was needed to limit structural loads during ascent. The motor design evolved through several block upgrades to increase performance and to increase safety and reliability. A major redesign occurred after STS-51L with the Redesigned Solid Rocket Motor. Significant improvements in the joint sealing systems were added. Design improvements continued throughout the Program via block changes with a number of innovations including development of low temperature o-ring materials and incorporation of a unique carbon fiber rope thermal barrier material. Recovery of the motors and post flight inspection improved understanding of hardware performance, and led to key design improvements. Because of the multidecade program duration material obsolescence was addressed, and requalification of materials and vendors was sometimes needed. Thermal protection systems and ablatives were used to protect the motor cases and nozzle structures. Significant understanding of design and manufacturing features of the ablatives was developed during the program resulting in optimization of design features and processing parameters. The project advanced technology in eliminating ozone-depleting materials in manufacturing processes and the development of an asbestos-free case insulation. Manufacturing processes for the large motor components were unique and safety in the manufacturing environment was a special concern. Transportation and handling approaches were also needed for the large hardware segments. The reusable solid rocket motor achieved significant reliability via process control, ground test programs, and postflight assessment. Process control is mandatory for a solid rocket motor as an acceptance test of the delivered product is not feasible. Process control included process failure modes and effects analysis, statistical process control, witness panels, and process product integrity audits. Material controls and inspections were maintained throughout the sub tier vendors. Material fingerprinting was employed to assess any drift in delivered material properties. The RSRM maintained both full scale and sub-scale test articles. These enabled continuous improvement of design and evaluation of process control and material behavior. Additionally RSRM reliability was achieved through attention to detail in post flight assessment to observe any shift in performance. The postflight analysis and inspections provided invaluable reliability data as it enables observation of actual flight performance, most of which would not be available if the motors were not recovered. These unique challenges, features of the reusable solid rocket motor, materials and manufacturing issues, and design improvements will be discussed in the paper.

Moore, Dennis R.↗

Design Evaluation of a Next-Generation High-Temperature Particle Receiver for Concentrating Solar Thermal Applications

High-temperature particle receivers are being developed to achieve temperatures in excess of 700 °C for advanced power cycles and solar thermochemical processes. This paper describes designs and features of a falling particle receiver system that has been evaluated and tested at the National Solar Thermal Test Facility at Sandia National Laboratories. These advanced designs are intended to reduce heat losses and increase the thermal efficiency. Novel features include aperture covers, active air flow, particle flow obstructions, and optimized receiver shapes that minimize advective heat losses, increase particle curtain opacity and uniformity, and reduce cavity wall temperatures. Control systems are implemented in recent on-sun tests to maintain a desired particle outlet temperature using an automated closed-loop proportional–integral–derivative controller. These tests demonstrate the ability to achieve and maintain particle outlet temperatures approaching 800 °C with efficiencies between 60 and 90%, depending on incident power, mass flow, and environmental conditions. Lessons learned regarding the testing of design features and overall receiver operation are also presented.

Mills, Brantley H.↗

Design Advancement of an Indoor Soil Deposition Chamber: A Road to Standardization

An indoor soil deposition chamber has been designed and constructed at the Arizona State University Photovoltaic Reliability Lab (ASU-PRL) to simulate photovoltaic (PV) module soiling in the field. This paper discusses the next set of revisions to the design, which are organized into three categories: design improvements, cost reduction, and new features. The design process was carried out with the intention of working toward the development of a national or international soiling standard. The improvements made to the chamber are described in detail to provide a guide for other laboratories or research facilities who wish to study photovoltaic (PV) soiling.

14 SOLAR ENERGY↗

Development of the Galileo Attitude and Articulation Control Subsystem flight software

The ongoing design and implementation of the Project Galileo Attitude and Articulation Control Subsystem (AACS) flight software is outlined, as well as the more important problems that were experienced in the development of this software. The important characteristics of the Galileo spacecraft are described, as are the major requirements driving the software design. The important features of the design are stated and discussed, and a modes and tasks transition diagram is presented. The AACS software implementation is covered, and the algorithms active in each task are shown. Finally, some of the design and management techniques used in the course of the software development are discussed.

Krasner, S. M.↗

Modal Filters for Infrared Interferometry

Modal filters in the approximately equal to 10-micrometer spectral range have been implemented as planar dielectric waveguides in infrared interferometric applications such as searching for Earth-like planets. When looking for a small, dim object ("Earth") in close proximity to a large, bright object ("Sun"), the interferometric technique uses beams from two telescopes combined with a 180 phase shift in order to cancel the light from a brighter object. The interferometer baseline can be adjusted so that, at the same time, the light from the dimmer object arrives at the combiner in phase. This light can be detected and its infrared (IR) optical spectra can be studied. The cancellation of light from the "Sun" to approximately equal to 10(exp 6) is required; this is not possible without special devices-modal filters- that equalize the wavefronts arriving from the two telescopes. Currently, modal filters in the approximately equal to 10-micrometer spectral range are implemented as single- mode fibers. Using semiconductor technology, single-mode waveguides for use as modal filters were fabricated. Two designs were implemented: one using an InGaAs waveguide layer matched to an InP substrate, and one using InAlAs matched to an InP substrate. Photon Design software was used to design the waveguides, with the main feature all designs being single-mode operation in the 10.5- to 17-micrometer spectral range. Preliminary results show that the filter's rejection ratio is 26 dB.

Ksendzov, Alexander↗

Impact and Crashworthiness Characteristics of Venera Type Landers for Future Venus Missions

In this paper an in-depth investigation of the structural design of the Venera 9-14 landers is explored. A complete reverse engineering of the Venera lander was required. The lander was broken down into its fundamental components and analyzed. This provided in-sights into the hidden features of the design. A trade study was performed to find the sensitivity of the lander's overall mass to the variation of several key parameters. For the lander's legs, the location, length, configuration, and number are all parameterized. The size of the impact ring, the radius of the drag plate, and other design features are also parameterized, and all of these features were correlated to the change of mass of the lander. A multi-fidelity design tool used for further investigation of the parameterized lander was developed. As a design was passed down from one level to the next, the fidelity, complexity, accuracy, and run time of the model increased. The low-fidelity model was a highly nonlinear analytical model developed to rapidly predict the mass of each design. The medium and high fidelity models utilized an explicit finite element framework to investigate the performance of various landers upon impact with the surface under a range of landing conditions. This methodology allowed for a large variety of designs to be investigated by the analytical model, which identified designs with the optimum structural mass to payload ratio. As promising designs emerged, investigations in the following higher fidelity models were focused on establishing their reliability and crashworthiness. The developed design tool efficiently modelled and tested the best concepts for any scenario based on critical Venusian mission requirements and constraints. Through this program, the strengths and weaknesses inherent in the Venera-Type landers were thoroughly investigated. Key features identified for the design of robust landers will be used as foundations for the development of the next generation of landers for future exploration missions to Venus.

Schroeder, Kevin↗

A Modular Integration Design of LCL Circuit Featuring Field Enhancement and Misalignment Tolerance for Wireless EV Charging

One of the major challenges of high-order wireless charging circuit is to reduce the system volume and cost induced by its additional components. Based on an LCL-S circuit, this paper proposes a modular integration design, in which an identical compensation inductor and transmitter are closely coupled. A new compensation method is derived to enable zero phase angle (ZPA) and constant current (CC) output. Identical currents are fed into the same reference terminals of both inductors to enable transmission field enhancement and to eliminate reactive power flow between the inductors. A misalignment tolerant coil is used to improve the output power stability under random parking imperfection. The proposed integration design achieves enhanced transmission capacity. Experiments are carried out to verify the proposed design.

Zhang, Pengcheng↗

Design of free patterns of nanocrystals with ad hoc features via templated dewetting

Design of monodisperse ultra-small nanocrystals (NCs) into large scale patterns with ad hoc features is demonstrated. The process makes use of solid state dewetting of a thin film templated through alloy liquid metal ion source focused ion beam (LMIS-FIB) nanopatterning. The solid state dewetting initiated at the edges of the patterns controllably creates the ordering of NCs with ad hoc placement and periodicity. The NC size is tuned by varying the nominal thickness of the film while their position results from the association of film retraction from the edges of the lay out and Rayleigh-like instability. The use of ultra-high resolution LMIS-FIB enables to produce monocrystalline NCs with size, periodicity, and placement tunable as well. It provides routes for the free design of nanostructures for generic applications in nanoelectronics.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Bowtie filters for dedicated breast CT: Analysis of bowtie filter material selection

Purpose: For a given bowtie filter design, both the selection of material and the physical design control the energy fluence, and consequently the dose distribution, in the object. Using three previously described bowtie filter designs, the goal of this work is to demonstrate the effect that different materials have on the bowtie filter performance measures. Methods: Three bowtie filter designs that compensate for one or more aspects of the beam-modifying effects due to the differences in path length in a projection have been designed. The nature of the designs allows for their realization using a variety of materials. The designs were based on a phantom, 14 cm in diameter, composed of 40% fibroglandular and 60% adipose tissue. Bowtie design #1 is based on single material spectral matching and produces nearly uniform spectral shape for radiation incident upon the detector. Bowtie design #2 uses the idea of basis-material decomposition to produce the same spectral shape and intensity at the detector, using two different materials. With bowtie design #3, it is possible to eliminate the beam hardening effect in the reconstructed image by adjusting the bowtie filter thickness so that the effective attenuation coefficient for every ray is the same. Seven different materials were chosen to represent a range of chemical compositions and densities. After calculation of construction parameters for each bowtie filter design, a bowtie filter was created using each of these materials (assuming reasonable construction parameters were obtained), resulting in a total of 26 bowtie filters modeled analytically and in the PENELOPE Monte Carlo simulation environment. Using the analytical model of each bowtie filter, design profiles were obtained and energy fluence as a function of fan-angle was calculated. Projection images with and without each bowtie filter design were also generated using PENELOPE and reconstructed using FBP. Parameters such as dose distribution, noise uniformity, and scatter were investigated. Results: Analytical calculations with and without each bowtie filter show that some materials for a given design produce bowtie filters that are too large for implementation in breast CT scanners or too small to accurately manufacture. Results also demonstrate the ability to manipulate the energy fluence distribution (dynamic range) by using different materials, or different combinations of materials, for a given bowtie filter design. This feature is especially advantageous when using photon counting detector technology. Monte Carlo simulation results from PENELOPE show that all studied material choices for bowtie design #2 achieve nearly uniform dose distribution, noise uniformity index less than 5%, and nearly uniform scatter-to-primary ratio. These same features can also be obtained using certain materials with bowtie designs #1 and #3. Conclusions: With the three bowtie filter designs used in this work, the selection of material is an important design consideration. An appropriate material choice can improve image quality, dose uniformity, and dynamic range.

60 APPLIED LIFE SCIENCES↗