Results for “conditional expectations” — Page 88

NASA NTRS2019

Dynamic Testing of a High-Specific-Torque Concentric Magnetic Gear

This paper presents initial measurements of the efficiency of NASA's 2nd magnetic gear prototype. A detailed discussion of the test rig's design and capabilities was presented, along with a thorough uncertainty analysis. The reported uncertainties are 95% confidence intervals that include the effects of temperature and parasitic loads. The prototype's response was measured at output speeds between 124 rpm and 744 rpm for a controlled output torque of 10 Nm (8% of the prototype's maximum torque). After correcting for tare losses, the prototype's efficiency was found to decrease from 90.0% to 83.0% as speed increased. If the efficiency is extrapolated to a typical operating condition (85% of maximum torque) using the good assumption that energy loss is approximately independent of the transmitted torque, the expected efficiency would be 99.0% to 98.4%, which exceeds the state of the art for these speeds.

magnetic gears↗

NASA NTRS2019

Dynamic Testing of a High-Specific-Torque Concentric Magnetic Gear

This presentation presents measurements of the efficiency of NASA's 2nd magnetic gear prototype. A detailed discussion of the test rig used to make these measurements was presented, including a thorough uncertainty analysis. The reported uncertainties are 95% confidence intervals that include the effects of temperature and parasitic loads. The prototype's response was measured at output speeds between 124 rpm and 744 rpm for a controlled output torque of 10 Nm (8% of the prototype's maximum torque). After correcting for tare losses, the prototype's efficiency was found to decrease from 90.0% to 83.0% as speed increased. If the efficiency is extrapolated to a typical operating condition (85% of maximum torque) using the good assumption that energy loss is approximately independent of the transmitted torque,the expected efficiency would be 99.0% to 98.4%, which exceeds the state of the art for these speeds.

Scheidler, Justin↗

NASA NTRS2019

High Speed Testing of a High Efficiency Concentric Magnetic Gear

This presentation presents measurements of the efficiency of NASA's 2nd magnetic gear prototype. A detailed discussion of the test rig used to make these measurements was presented, including a thorough uncertainty analysis. The reported uncertainties are 95% confidence intervals that include the effects of temperature and parasitic loads. The prototype's response was measured at output speeds between 124 rpm and 744 rpm for a controlled output torque of 10 Nm (8% of the prototype's maximum torque). After correcting for tare losses, the prototype's efficiency was found to decrease from 90.0% to 83.0% as speed increased. If the efficiency is extrapolated to a typical operating condition (85% of maximum torque) using the good assumption that energy loss is approximately independent of the transmitted torque,the expected efficiency would be 99.0% to 98.4%, which exceeds the state of the art for these speeds.

Scheidler, Justin↗

NASA NTRS2021

Parametric Study of State-of-Charge for an Electric Aircraft in Urban Air Mobility

The envisioned concept of urban air mobility is anticipated to support passenger transportation, cargo delivery, and emergency services in major metropolitan areas with increasing autonomy levels in the future. Distributed electric propulsion powered electric vertical takeoff and landing aircraft are expected to enable urban air mobility. However, the low specific energy of onboard lithium-ion polymer batteries and wind conditions impose constraints on flight endurance. Therefore, to enable autonomous urban air mobility operations using electric aircraft, one of the critical steps from a safety and efficiency perspective is to understand how various operational and environmental conditions impact the state-of-charge of the onboard lithium-ion polymer batteries. This research performs a parametric study of the state-of-charge for a NASA-proposed conceptual multirotor aircraft flight in the urban environment. The parameters considered for the parametric analysis are cruise airspeed, cruise altitude, climb and descent profiles, wind conditions (wind magnitude, wind direction relative to the route, and wind magnitude uncertainty), and required time of arrival.

Urban Air Mobility↗

NASA NTRS2021

Parametric Study of State of Charge for an Electric Aircraft in Urban Air Mobility

The envisioned concept of urban air mobility is anticipated to support passenger transportation, cargo delivery, and emergency services in major metropolitan areas with increasing autonomy levels in the future. Distributed electric propulsion powered electric vertical takeoff and landing aircraft are expected to enable urban air mobility. However, the low specific energy of onboard lithium-ion polymer batteries and wind conditions impose constraints on flight endurance. Therefore, to enable autonomous urban air mobility operations using electric aircraft, one of the critical steps from a safety and efficiency perspective is to understand how various operational and environmental conditions impact the state-of-charge of the onboard lithium-ion polymer batteries. This research performs a parametric study of the state-of-charge for a NASA-proposed conceptual multirotor aircraft flight in the urban environment. The parameters considered for the parametric analysis are cruise airspeed, cruise altitude, climb and descent profiles, wind conditions (wind magnitude, wind direction relative to the route, and wind magnitude uncertainty), and required time of arrival.

Urban Air Mobility↗

NASA NTRS2021

Sensitivity Limits of Space-Based Interferometric Gravitational Wave Observatories from the Solar Wind

Space-based interferometric gravitational wave instruments such as the ESA/NASA Laser Interferometer Space Antenna (LISA) observe gravitational waves by measuring changes in the light travel time between widely separated spacecraft. One potential noise source for these instruments is interaction with the solar wind, in particular the free electrons in the interplanetary plasma. Variations in the integrated column density of free electrons along the laser links will lead to time-of-flight delays which directly compete with signals produced by gravitational waves. In this paper we present a simplified model of the solar plasma relevant for this problem, anchor key parameters of our model using data from the NASA Wind/solar wind experiment instrument, and derive estimates for the effect in the LISA measurement. We find that under normal solar conditions, the gravitational wave sensitivity limit from the free-electron effect is smaller than other noise sources that are expected to limit LISA’s sensitivity.

Oliver Jennrich↗

NASA NTRS2026

Artemis Suit Material Optical Property Testing of Dust Exposed Fabrics

This paper highlights one aspect of NASA’s ongoing technology-infusion effort to design, fabricate, and test a next-generation outer shell fabric for a lunar Extravehicular Activity (EVA) space suit, a critical component of sustained lunar exploration. Managing thermal loads on the Moon is essential for astronaut safety and suit performance. The suit’s exterior fabric directly influences heat gain and loss through its optical properties: low solar absorptivity minimizes sunlight absorption, while high infrared emissivity aids radiative cooling. Lunar regolith complicates this balance. Its fine, abrasive particles possess unique optical behavior that can lower reflectivity and raise emissivity when embedded in or adhered to fabric surfaces, degrading thermal control and increasing the risk of overheating or cooling inefficiency. To quantify these effects, the Artemis Suit Materials (ASM) team measured solar absorptance and infrared emissivity of clean and dust-soiled Ortho Fabric, establishing beginning-of-life (BOL) and end-of-life (EOL) benchmarks. EOL conditions were simulated with a rotary tumbler abrasion process using lunar dust simulant and ceramic media to reproduce cumulative wear expected during surface operations. Tests also included unmodified fabrics and a fabric/film laminate system containing titanium dioxide to evaluate potential improvements in dust resistance and optical performance. Results from these evaluations provide critical insight into how lunar dust alters fabric thermal behavior and inform the design of bespoke suit materials that maintain required optical properties throughout mission life, supporting safe and effective long-duration EVA on the lunar surface.

space↗

NASA NTRS2026

Artemis Suit Material Optical Property Testing of Dust Exposed Fabrics

This paper highlights one aspect of NASA’s ongoing technology-infusion effort to design, fabricate, and test a next-generation outer shell fabric for a lunar Extravehicular Activity (EVA) space suit, a critical component of sustained lunar exploration. Managing thermal loads on the Moon is essential for astronaut safety and suit performance. The suit’s exterior fabric directly influences heat gain and loss through its optical properties: low solar absorptivity minimizes sunlight absorption, while high infrared emissivity aids radiative cooling. Lunar regolith complicates this balance. Its fine, abrasive particles possess unique optical behavior that can lower reflectivity and raise emissivity when embedded in or adhered to fabric surfaces, degrading thermal control and increasing the risk of overheating or cooling inefficiency. To quantify these effects, the Artemis Suit Materials (ASM) team measured solar absorptance and infrared emissivity of clean and dust-soiled Ortho Fabric, establishing beginning-of-life (BOL) and end-of-life (EOL) benchmarks. EOL conditions were simulated with a rotary tumbler abrasion process using lunar dust simulant and ceramic media to reproduce cumulative wear expected during surface operations. Tests also included unmodified fabrics and a fabric/film laminate system containing titanium dioxide to evaluate potential improvements in dust resistance and optical performance. Results from these evaluations provide critical insight into how lunar dust alters fabric thermal behavior and inform the design of bespoke suit materials that maintain required optical properties throughout mission life, supporting safe and effective long-duration EVA on the lunar surface.

Textile↗

NASA NTRS2014

Clustering Days with Similar Airport Weather Conditions

On any given day, traffic flow managers must often rely on past experience and intuition when developing traffic flow management initiatives that mitigate imbalances between the aircraft demand and the weather impacted airport capacity. The goal of this study was to build on recent efforts to apply data mining classification and clustering algorithms to vast archives of historical weather and air traffic data to identify patterns and past decisions that can ultimately inform day-of-operations decision-making. More specifically, this study identified similar weather impacted days at select U.S. airports, and analyzed the traffic management initiatives implemented on these representative days. The identification of the similar days was accomplished by applying a decision tree algorithm to the hourly Localized Aviation Model Output Statistics Program observations and the arrival delays for Newark Liberty International Airport. The branches from the trained decision tree were subsequently pruned to identify four weather conditions that resulted in medium to high delays for the arrivals scheduled to Newark in 2012. Using these weather conditions, four, daily airport-level Weather Impacted Traffic Index values were calculated using the Localized Aviation Model Output Statistics Program observations and the 2012 scheduled arrival counts from the FAAs Aviation System Performance Metric system. The four, daily Weather Impacted Traffic Index values for 2012 were subsequently clustered using an Expectation Maximization clustering algorithm, and nine unique types of weather days at Newark were identified. By far the most prominent type of day at Newark was a day associated with relatively good weather conditions, where there was little convective activity, winds were low, ceilings and visibility were high and there was little precipitation. Moderate levels of convective activity characterized the next most prominent type of day. Days with persistently high winds or low ceiling and visibility levels were relatively rare in 2012. Lastly, the frequency at which Ground Delay Programs, Ground Stops and Miles-in-Trail restrictions were implemented on each of the typical types of days at Newark were analyzed. Based on the results, it does appear as if the usage of Miles-in-Trail, Ground Delay Program and Ground Stop restrictions correlates well with the severity of the weather associated with each unique type of weather impacted day at Newark. Furthermore, the results demonstrate that it is feasible to use historical weather and air traffic archives to provide guidance on the types of traffic management restrictions to implement in response to the weather conditions impacting an airport.

traffic flow management↗

NASA NTRS2014

Clustering Days with Similar Airport Weather Conditions

On any given day, traffic flow managers must often rely on past experience and intuition when developing traffic flow management initiatives that mitigate imbalances between the aircraft demand and the weather impacted airport capacity. The goal of this study was to build on recent efforts to apply data mining classification and clustering algorithms to vast archives of historical weather and air traffic data to identify patterns and past decisions that can ultimately inform day-of-operations decision-making. More specifically, this study identified similar weather impacted days at select U.S. airports, and analyzed the traffic management initiatives implemented on these representative days. The identification of the similar days was accomplished by applying a decision tree algorithm to the hourly Localized Aviation Model Output Statistics Program observations and the arrival delays for Newark Liberty International Airport. The branches from the trained decision tree were subsequently pruned to identify four weather conditions that resulted in medium to high delays for the arrivals scheduled to Newark in 2012. Using these weather conditions, four, daily airport-level Weather Impacted Traffic Index values were calculated using the Localized Aviation Model Output Statistics Program observations and the 2012 scheduled arrival counts from the FAAs Aviation System Performance Metric system. The four, daily Weather Impacted Traffic Index values for 2012 were subsequently clustered using an Expectation Maximization clustering algorithm, and nine unique types of weather days at Newark were identified. By far the most prominent type of day at Newark was a day associated with relatively good weather conditions, where there was little convective activity, winds were low, ceilings and visibility were high and there was little precipitation. Moderate levels of convective activity characterized the next most prominent type of day. Days with persistently high winds or low ceiling and visibility levels were relatively rare in 2012. Lastly, the frequency at which Ground Delay Programs, Ground Stops and Miles-in-Trail restrictions were implemented on each of the typical types of days at Newark were analyzed. Based on the results, it does appear as if the usage of Miles-in-Trail, Ground Delay Program and Ground Stop restrictions correlates well with the severity of the weather associated with each unique type of weather impacted day at Newark. Furthermore, the results demonstrate that it is feasible to use historical weather and air traffic archives to provide guidance on the types of traffic management restrictions to implement in response to the weather conditions impacting an airport.

weather↗

NASA NTRS2021

Between-Simulator Comparison of Motion Filter Order and Break Frequency Interaction Effects on Pilot Control Behavior

This paper investigates the interaction effects of motion filter order and break frequency on pilots' manual control behavior and control performance using two simulators. Eighteen pilots performed the experiment in the Vertical Motion Simulator (VMS) at NASA Ames Research Center and twenty pilots in the SIMONA Research Simulator at Delft University of Technology. The experiment used a full-factorial design with three motion filter orders (first-, second-, and third-order) and two filter break frequencies (0.5 and 2.0 rad/s), in addition to reference no-motion and full-motion conditions. Key task variables, such as the quality of the motion and visual cues and the characteristics of the sidestick, were matched across both simulators. Overall, the expected effects of filter order and break frequency variations were found, with both increasing order and increasing break frequency causing pilots to use less motion feedback in their control strategy, resulting in lower tracking performance. Furthermore, across the wide range of filter orders tested in the experiment, the existing Sinacori-Schroeder motion fidelity criterion was found to be a good predictor of the interaction effects of both filter settings on pilot control behavior. For the same motion condition, there was a consistent offset in the results between simulators, due to the more high-gain control strategy adopted by a number of the VMS pilots. Still, the observed relative trends in pilot control behavior and performance between motion conditions were equivalent in both simulators and thus accurately replicated.

manual control↗

DOE OSTI2024

Droplet Growth or Evaporation Does Not Buffer the Variability in Supersaturation in Clean Clouds

Abstract Water vapor supersaturation in clouds is a random variable that drives activation and growth of cloud droplets. The Pi Convection–Cloud Chamber generates a turbulent cloud with a microphysical steady state that can be varied from clean to polluted by adjusting the aerosol injection rate. The supersaturation distribution and its moments, e.g., mean and variance, are investigated for varying cloud microphysical conditions. High-speed and collocated Eulerian measurements of temperature and water vapor concentration are combined to obtain the temporally resolved supersaturation distribution. This allows quantification of the contributions of variances and covariances between water vapor and temperature. Results are consistent with expectations for a convection chamber, with strong correlation between water vapor and temperature; departures from ideal behavior can be explained as resulting from dry regions on the warm boundary, analogous to entrainment. The saturation ratio distribution is measured under conditions that show monotonic increase of liquid water content and decrease of mean droplet diameter with increasing aerosol injection rate. The change in liquid water content is proportional to the change in water vapor concentration between no-cloud and cloudy conditions. Variability in the supersaturation remains even after cloud droplets are formed, and no significant buffering is observed. Results are interpreted in terms of a cloud microphysical Damköhler number (Da), under conditions corresponding to , i.e., the slow-microphysics regime. This implies that clouds with very clean regions, such that is satisfied, will experience supersaturation fluctuations without them being buffered by cloud droplet growth. Significance Statement The saturation ratio (humidity) in clouds controls the growth rate and formation of cloud droplets. When air in a turbulent cloud mixes, the humidity varies in space and time throughout the cloud. This is important because it means cloud droplets experience different growth histories, thereby resulting in broader size distributions. It is often assumed that growth and evaporation of cloud droplets buffers out some of the humidity variations. Measuring these variations has been difficult, especially in the field. The purpose of this study is to measure the saturation ratio distribution in clouds with a range of conditions. We measure the in-cloud saturation ratio using a convection cloud chamber with clean to polluted cloud properties. We found in clouds with low concentrations of droplets that the variations in the saturation ratio are not suppressed.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2024

Getting to the root of the problem: Soil carbon and microbial responses to root inputs within a buried paleosol along an eroding hillslope in southwestern Nebraska, USA

Large quantities of soil carbon (C) can persist within paleosols for millennia due to burial and subsequent isolation from plant-derived inputs, atmospheric conditions, and microbial activity at the modern surface. Erosion exposes buried soils to modern root-derived C influx via root exudation and root turnover, thus stimulating microbial activity leading to SOC decomposition and accumulation through organo-mineral stabilization of modern C. With this study we aim to quantify how modern root-derived C inputs impact paleosol C decomposition and stabilization across varying degrees of isolation from modern surface conditions in southwestern Nebraska, USA, where hillslope erosion is bringing a buried Late-Pleistocene-early Holocene paleosol (the “Brady Soil”) closer to the modern surface. We collected Brady Soil samples from 0.2m, 0.4m, and 1.2m below the modern surface and conducted two lab-based incubations. Soils were amended with either (1) a lab-synthesized mixture of low molecular weight compounds (12 atom% 13 C), or (2) 13 C enriched root residues (92 atom% 13 C), in 30-day and 240-day incubation experiments, respectively. Here we determined microbial responses to synthetic root exudates and residues by partitioning the 13 C label from Brady Soil C, including measurements of total, root, and primed C respiration, microbial biomass C (MBC), microbial C use efficiency (CUE). To assess the capacity of isolated paleosols to accrue modern plant C, we used Nano-scale Secondary Ion Mass Spectrometry imaging. We found that: (1) adding root-derived C inputs primed Brady Soil C across all depths, and was mediated by depth and composition of root additions; (2) root-derived C inputs stimulated microbial biomass C (MBC) growth similarly across depths, but the magnitude of CUE and MBC varied by chemistry of root-derived additions; (3) new particulate organic matter was incorporated into mineral-associated pools over time; (4) material from the added root residues was found in association with bacterial cells and fungal hyphae as well as with soil aggregate and mineral surfaces. Our study shows that paleosols defy expectations of C content and reactivity with depth, and changes in land cover and climate will expose buried paleosols to modern surface conditions, increasing respired C. This work highlights the importance of evaluating the role resurfacing buried soils through landscape change plays in C cycle feedbacks to the climate system.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2025

Coal Enhanced PEEK Filament Production for Additive Manufacturing in Industrial Services

The project (Award DE-FE0032146), led by Baker Hughes in collaboration with the University of Wyoming, aims to develop composite PEEK (Polyether-ether-ketone) materials enhanced using coal-derived graphene-based additives suitable for additive manufacturing (3D printing). Coal char (CC), graphene oxide (GO), and reduced graphene oxide (rGO), derived from Powder River Basin (PRB) coal, were successfully integrated into commercial PEEK feedstock. The composite PEEK materials demonstrated tensile and flexural strengths and modulus, Shore hardness, and thermal properties similar to unfilled PEEK. Dielectric strength of 0.5% GO/PEEK is twice that of unfilled PEEK. However, tensile elongation and Izod impact toughness of the composite materials are lower than unfilled PEEK. The 10% CC/PEEK material also shows good recyclability albeit with slightly increased glass transition and cold crystallization temperatures. Filaments of the composite PEEK materials were fabricated using a Filabot system. 3D printing of the composite PEEK initially encountered feeding stoppage caused by the non-uniform diameter of the filament, which was resolved by reducing the nominal diameter from 1.75 to 1.65 mm. The printability of the composite PEEK filaments is limited in geometry and build time, driven by differences in base PEEK feedstock from the commercial PEEK filament at printing conditions. Prototype part printed using the composite filaments shows inconsistent bead width and bead interruption resulting in porosity. Preliminary process and economic evaluation using PRB coal char estimates the cost of GO to be $0.5/lb. Considering the small fraction expected in the composite PEEK, the GO cost is several orders of magnitude lower than the commercial PEEK filament. It is recommended that the printability of composite PEEK filaments to be improved by optimizing the composite PEEK material at the printing conditions and reducing the variations in filament extrusion. Also important is to identify the mechanisms of how coal-derived additives affect the composite PEEK performance and printing characteristics to allow customized material design and processing for target performance.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2023

Benchmark Specifications for TREAT Tests M5, M6, and M7

Detailed information describing three TREAT tests performed on metallic fuels has been collected and organized for use as a benchmark in evaluating the performance of metallic fuel models and codes. The tests, designated M5, M6, and M7, subjected EBR-II-irradiated fuel pins to a single type of overpower transient (at prototypical conditions with full coolant flow and an exponential power rise on an 8 second period) in flowing sodium loops. Six fuel pins were tested; five were ternary (U-19Pu-10Zr) alloy fuel clad in D9 with burnup ranging from 0.8 to 9.8 at. %, and one was binary alloy fuel (U-10Zr) clad in HT9 with 2.9 at. % burnup. The information gathered from the test records is expected to be useful for pre-transient characterization of the irradiated fuel pins as well as the transient analysis of the metallic fuel when subjected to severe accident conditions. This report presents benchmark specifications for the M5, M6, and M7 TREAT tests, identifies where primary sources of benchmark-related information can be found, and includes background information to help a user of the data understand their applicability and limitations.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

NASA NTRS1987

Effectiveness of back-to-back testing

Three models of back-to-back testing processes are described. Two models treat the case where there is no intercomponent failure dependence. The third model describes the more realistic case where there is correlation among the failure probabilities of the functionally equivalent components. The theory indicates that back-to-back testing can, under the right conditions, provide a considerable gain in software reliability. The models are used to analyze the data obtained in a fault-tolerant software experiment. It is shown that the expected gain is indeed achieved, and exceeded, provided the intercomponent failure dependence is sufficiently small. However, even with the relatively high correlation the use of several functionally equivalent components coupled with back-to-back testing may provide a considerable reliability gain. Implications of this finding are that the multiversion software development is a feasible and cost effective approach to providing highly reliable software components intended for fault-tolerant software systems, on condition that special attention is directed at early detection and elimination of correlated faults.

Vouk, Mladen A.↗

NASA NTRS2019

Enhanced Habitability on High Obliquity Bodies near the Outer Edge of the Habitable Zone of Sun-Like Stars

High obliquity planets represent potentially extreme limits of terrestrial climate, as they exhibit large seasonality, a reversed annual-mean pole-to-equator gradient of stellar heating, and novel cryospheres. A suite of 3D global climate model simulations is performed for low and high obliquity planets with various stellar fluxes, CO2 concentrations, and initial conditions to explore the propensity for high obliquity climates to undergo global glaciation. We also simulate planets with thick CO2 or H2 atmospheres, such as those expected to develop near or beyond the outer edge of the habitable zone. We show that high obliquity planets are hotter than their low obliquity counterparts due to ice-albedo feedbacks for cold climates, and water vapor in warm climates. We suggest that the water vapor greenhouse trapping is greater on high obliquity bodies for a given global-mean temperature due to the different dynamical regimes that occur between the two states. While equatorial ice belts are stable at high obliquity in some climate regimes, it is substantially harder to achieve global glaciation than for a low obliquity planet. Temperate polar conditions can be present at high obliquity at forcings for which low obliquity planets would be in a hard snowball state. Furthermore, open ocean can persist even in the winter hemisphere and when global-mean temperatures are well below freezing. However, the influence of obliquity diminishes for dense atmospheres, in agreement with calculations from 1D energy balance models.

Planet and satellite atmospheres↗

NASA NTRS2001

Coupled Growth in Hypermonotectics

The overall objective of this project is to obtain a fundamental understanding of the physics controlling solidification processes in immiscible alloy systems. The investigation involves both experimentation and the development of a model describing solidification in monotectic systems. The experimental segment was designed to first demonstrate that it is possible to obtain interface stability and steady state coupled growth in hypermonotectic alloys through microgravity processing. Microgravity results obtained to date have verified this possibility. Future flights will permit experimental determination of the limits of interface stability and the influence of alloy composition and growth rate on microstructure. The objectives of the modeling segment of the investigation include prediction of the limits of interface stability, modeling of convective flow due to residual acceleration, and the influence of surface tension driven flows at the solidification interface. The study of solidification processes in immiscible alloy systems is hindered by the inherent convective flow that occurs on Earth and by the possibility of sedimentation of the higher density immiscible liquid phase. It has been shown that processing using a high thermal gradient and a low growth rate can lead to a stable macroscopically planar growth front even in hypermonotectic alloys. Processing under these growth conditions can avoid constitutional supercooling and prevent the formation of the minor immiscible liquid phase in advance of the solidification front. However, the solute depleted boundary layer that forms in advance of the solidification front is almost always less dense than the liquid away from the solidification front. As a result, convective instability is expected. Ground based testing has indicated that convection is a major problem in these alloy systems and leads to gross compositional variations along the sample and difficulties maintaining interface stability. Sustained low gravity processing conditions are necessary in order to minimize these problems and obtain solidification conditions which approach steady state.

Andrews, J. Barry↗