SEARCH · Engineering Papers

Results for “array”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,585 records · Page 88

All sources NASA NTRS DOE OSTI

NASA NTRS1981

Heat transfer coefficients for staggered arrays of short pin fins

Short pin fins are often used to increase that heat transfer to the coolant in the trailing edge of a turbine blade. Due primarily to limits of casting technology, it is not possible to manufacture pins of optimum length for heat transfer purposes in the trailing edge region. In many cases the pins are so short that they actually decrease the total heat transfer surface area compared to a plain wall. A heat transfer data base for these short pins is not available in the literature. Heat transfer coefficients on pin and endwall surfaces were measured for several staggered arrays of short pin fins. The measured Nusselt numbers when plotted versus Reynolds numbers were found to fall on a single curve for all surfaces tested. The heat transfer coefficients for the short pin fins (length to diameter ratios of 1/2 and 2) were found to be about a factor of two lower than data from the literature for longer pin arrays (length to diameter ratios of about 8).

Vanfossen, G. J.↗

NASA NTRS1980

Frequency translating phase conjugation circuit for active retrodirective antenna array

An active retrodirective antenna array which has central phasing from a reference antenna element through a "tree" structured network of transmission lines utilizes a number of phase conjugate circuits (PCCs) at each node and a phase reference regeneration circuit (PRR) at each node except the initial node. Each node virtually coincides with an element of the array. A PCC generates the exact conjugate phase of an incident signal using a phase locked loop which combines the phases in an up converter, divides the sum by 2 and mixes the result with the phase in a down converter for phase detection. The PRR extracts the phase from the conjugate phase. Both the PCC and the PRR are not only exact but also free from mixer degeneracy.

Chernoff, R.↗

NASA NTRS1980

SPS large array simulation

Three types of computer simulations were developed to study the SPS microwave power transmission system (MPTS). The radially symmetric array simulation is low cost and is utilized to investigate general overall characteristics of the spacetenna at the array level only. "Tiltmain", a subarray level simulation program, is used to study the effects of system errors which modify the far-field pattern. The most recently designed program, "Modmain," takes the detail of simulation down to the RF module level and so to date is the closest numerical model of the reference design.

Rathjen, S.↗

NASA NTRS1980

Efficient structures for geosynchronous spacecraft solar arrays

Structural concepts for deploying and supporting lightweight solar array blankets for geosynchronous electrical powr are evaluated. First, the requirements for more mass efficient solar arrays is established by describing future needs. Then analytical results are set forth which show that not only must lighter weight blankets be developed but also the supporting structure must be improved proportionately. The SEPS configuration is taken to be the state of the art point of departure for improved structural concepts. Several directions for improvement are indicated.

Hedgepeth, J. M.↗

NASA NTRS1981

Study program for encapsulation materials interface for low-cost solar array

The service integrity of the bonded interface in solar cell modules used in solar arrays is addressed. The development of AC impedance as a nondestructive evaluation (NDE) methodology for solar arrays is reported along with development of corrosion models and materials selection criteria for corrosion resistant interfaces.

Kaelble, D. H.↗

NASA NTRS1981

Performance of the real-time array signal combiner during the Voyager mission

During the Voyager Mission each Deep Space Station used its 64 meter antenna together with a 34 meter antenna to form an array. Data were selected from the Saturn encounter period from November 2 to November 13, 1980, to analyze the signal combiner performance. A statistical analysis of the residual gain data from all of the arrayed Deep Space Stations indicates that the Real Time Combiner is operating within the designed accuracy range of 0.2 + or - 0.05 dB around the theoretical gain. A decrease in the residual gain value appears to correlate with an increase in antenna elevation, which may be directly related to the changing antenna gain with elevation. Overall, the combined signal to noise ratio is improved by an average of 0.62 + or - 0.15 dB over the 64 meter signal to noise ratio alone.

Bartok, C. D.↗

NASA NTRS1981

Infrared radiative transfer through a regular array of cuboidal clouds

Infrared radiative transfer through a regular array of cuboidal clouds is studied and the interaction of the sides of the clouds with each other and the ground is considered. The theory is developed for black clouds and is extended to scattering clouds using a variable azimuth two-stream approximation. It is shown that geometrical considerations often dominate over the microphysical aspects of radiative transfer through the clouds. For example, the difference in simulated 10 micron brightness temperature between black isothermal cubic clouds and cubic clouds of optical depth 10, is less than 2 deg for zenith angles less than 50 deg for all cloud fractions when viewed parallel to the array. The results show that serious errors are made in flux and cooling rate computations if broken clouds are modeled as planiform. Radiances computed by the usual practice of area-weighting cloudy and clear sky radiances are in error by 2 to 8 K in brightness temperature for cubic clouds over a wide range of cloud fractions and zenith angles. It is also shown that the lapse rate does not markedly affect the exiting radiances for cuboidal clouds of unit aspect ratio and optical depth 10.

HARSHVARDHAN↗

NASA NTRS1981

Low-cost solar array structure development

Early studies of flat-plate arrays have projected costs on the order of $50/square meter for installed array support structures. This report describes an optimized low-cost frame-truss structure that is estimated to cost below $25/square meter, including all markups, shipping an installation. The structure utilizes a planar frame made of members formed from light-gauge galvanized steel sheet and is supposed in the field by treated-wood trusses that are partially buried in trenches. The buried trusses use the overburden soil to carry uplift wind loads and thus to obviate reinforced-concrete foundations. Details of the concept, including design rationale, fabrication and assembly experience, structural testing and fabrication drawings are included.

Wilson, A. H.↗

NASA NTRS1980

Concentrator designs for space photovoltaic arrays

The unique set of operating constraints determining key concentrating solar array design characteristics for low earth orbital, geosynchronous and interplanetary missions are considered. Minimum cost is crucial at low earth orbits, performance and design life are needed in geosynchronous orbit, and structural pointing accuracy and radiation resistance are essential in interplanetary designs. The impact of such emerging technologies as ultrathin cells, gallium arsenide cells and cold mirrors is discussed. Power-to-mass ratios as high as 200 W per kilogram at a distance of 1 astronomical unit from the sun are possible, using concentrators in conjunction with gallium arsenide arrays.

Rockey, D. E.↗

NASA NTRS1981

Nonlinear in-plane and out-of-plane vibrations in solar arrays

This paper presents the results of analytical investigations of nonlinear effects in in-plane and out-of-plane vibrations of solar arrays caused by surface wrinkling of solar array blankets. It is shown that nonlinearities generated by wrinkles are important even for small deformations. Approximate analytical solutions describing the frequency and damping dependencies of the amplitudes of in-plane vibrations are derived. A new phenomenon - a parametrical resonance of out-of-plane vibrations induced by in-plane vibrations - is described.

Zak, M. A.↗

NASA NTRS1981

Experimental simulation of space plasma interactions with high voltage solar arrays

Operating high voltage solar arrays in the space environment can result in anomalously large currents being collected through small insulation defects. Tests of simulated defects have been conducted in a 45-cm vacuum chamber with plasma densities of 100,000 to 1,000,000/cu cm. Plasmas were generated using an argon hollow cathode. The solar array elements were simulated by placing a thin sheet of polyimide (Kapton) insulation with a small hole in it over a conductor. Parameters tested were: hole size, adhesive, surface roughening, sample temperature, insulator thickness, insulator area. These results are discussed along with some preliminary empirical correlations.

Stillwell, R. P.↗

NASA NTRS1981

Heat transfer coefficients for staggered arrays of short pin fins

Short pin fins are often used to increase the heat transfer to the coolant in the trailing edge of a turbine blade. Due primarily to limits of casting technology, it is not possible to manufacture pins of optimum length for heat transfer purposes in the trailing edge region. In many cases the pins are so short that they actually decrease the total heat transfer surface area compared to a plain wall. A heat transfer data base for these short pins is not available in the literature. Heat transfer coefficients on pin and endwall surfaces were measured for several staggered arrays of short pin fins. The measured Nusselt numbers when plotted versus Reynolds numbers were found to fall on a single curve for all surfaces tested. The heat transfer coefficients for the short pin fins (length to diameter ratios of 1/2 and 2) were found to be about a factor of two lower than data from the literature for longer pin arrays (length to diameter ratios of about 8).

Vanfossen, G. J.↗

NASA NTRS1980

A J-band space-fed phased array

A J-band, space-fed transmissive array suitable to the constraints of space platform applications has been designed and an engineering model array has been fabricated and tested. Attention is given to the design of the aperture, radiating element, phase shifter module, and flatplate feed. Test results and performance are discussed with reference to gain, sidelobe level, and beamwidth as functions of frequency and scan angle.

Orr, C. L.↗

NASA NTRS1981

The design of a microstrip antenna array for a UHF space telemetry link

An array of microstrip antenna panels was designed for use on a small instrumented satellite as part of a 400-MHz telemetry link between that satellite and NASA's shuttle spacecraft. A roughly omnidirectional phi-plane pattern was desired. The 1.4-wavelength diameter of the satellite and the various ports and structures on its surface presented strong constraints on the antenna array design. Eight antennas, each one a quarter-wavelength panel with one radiating and one shorted edge, were chosen. A phi-plane pattern ripple of 4.4 dB and a gain of at least 0.1 dB relative to a half-wavelength dipole were realized. The design technique used for the individual antenna panels included the study of feed-point location for impedance matching and the effect of losses in the dielectric. A superposition method was used to synthesize the radiation patterns for different numbers and different excitations of antennas on the satellite.

Post, R. E.↗

NASA NTRS1980

Thermal IR imaging system using a self-scanned HgCdTe/CCD detector array

It is likely that future high resolution earth observation imaging systems will utilize self-scanned IR detectors. In an initial step toward this goal, an IR imaging system operating in the 10 to 12 micron spectral region has been developed. This system uses a 9-element HgCdTe/CCD linear array operating in the photoconductive mode, nine pre-amplifiers and a silicon CCD multiplexer integrated into a focal plane assembly. Opto-mechanical techniques are used to scan the scene and images are produced in real time. The imaging performance of this system is described and measurements of noise, responsivity, specific detectivity, and detector sensitivity profiles are presented. The requirements for more advanced detector arrays for use in future NASA remote sensing missions are also discussed.

Husain-Abidi, A. S.↗

NASA NTRS1981

Submillisecond measurements of system optical modulation functions in mosaic focal plane arrays

Measurements of system optical modulation functions (MTF, SWR) may be distorted by time-dependent environmental effects (thermal, vibration, flexure) and by electronics drift. Fast data collection may therefore be advantageous by minimizing drift time. The problem of fast data collection is accentuated when modulation data must be taken on a large number of detectors in a focal plane array. A method has been developed for the generation and storage of knife edge data from focal plane arrays, where data collection time per detector is in the submillisecond range. Once knife edge collects are completed, MTF response is found using conventional convolution techniques. SWR is obtained directly from knife edge response using a computerized simulation algorithm which bypasses use of MTF harmonics. Requirements for detector electronics speed, damping, and dynamic range are considered.

Thurlow, P. E.↗

NASA NTRS1981

Cartographic potential of a spacecraft line-array camera system - Stereosat

A study of the Stereosat mission, which may acquire analog/digital stereo image data of cartographic quality with linear array camera systems, is presented, with attention given to the Stereosat system and the mission parameters, the utilization of the Stereosat studies in order to indicate the nature and scope of the problems associated with recording image data of high geometric fidelity from spacecraft equipped with line array sensors, and the assessing of the possibilities of meeting the completeness and accuracy requirements of cartographic products. A 713-km circular, sun-synchronous, near polar orbit, with an inclination of 98.24 deg and a repeat cycle of 48 days is designed to insure global coverage of the earth's land masses during the three-year lifetime of the mission. Three cameras (fore, vertical, and aft looking), mounted so as to record stereotriplets for a 61.4 km wide swath at a nominal focal plane scale of 1:1,000,000, are considered. The IFOV of 15 m should be adequate for producing thematic and image maps at scales of 1:50,000 to 1:250,000. The value of the coverage to cartographers will be dictated by the accuracy of the digital image data, which is largely a function of satellite control.

Welch, R.↗

NASA NTRS1980

An active alignment scheme for the MPTS array

In order to maximize the efficiency of the microwave power transmission system (MPTS), the surface of the array antenna must be extremely flat, which is difficult to achieve using passive techniques over the 1 km dimensions of the array. In order to achieve and maintain this required flatness, a rotating laser beam used for leveling applications on Earth was utilized as a reference system. A photoconductive sensor with a reflective collecting surface was used to determine the displacement and polarity of any misalignment and automatically engage a stepping motor to drive a variable-length mechanism to make the necessary corrections. Once aligned, little power is dissipated since a nulling bridge circuit that centers on the beam is used, an important alignment feature since even laser beams broaden considerably at 1 km distances.

Iwasaki, R.↗