Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Thermal Control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,585 records · Page 88

In-Space Demonstration of Spray-on Solar White Paint

Discs coated with spray-on solar white and two similar thermal control coatings were flown in low earth orbit for roughly five hours. While in orbit, the coated discs were exposed to direct sunlight and to deep space for short intervals. Measurements of disc temperatures showed that the spray-on solar white coating had the lowest absorption of sunlight. Numerical modeling was used to infer that spray-on solar white had a solar absorptance between 0.02 and 0.04 and a thermal emittance between 0.93 and 0.99, both of which are consistent with terrestrial laboratory measurements.

Solar White↗

Design of Accumulators and Liquid/Gas Charging of Single Phase Mechanically Pumped Fluid Loop Heat Rejection Systems

For single phase mechanically pumped fluid loops used for thermal control of spacecraft, a gas charged accumulator is typically used to modulate pressures within the loop. This is needed to accommodate changes in the working fluid volume due to changes in the operating temperatures as the spacecraft encounters varying thermal environments during its mission. Overall, the three key requirements on the accumulator to maintain an appropriate pressure range throughout the mission are: accommodation of the volume change of the fluid due to temperature changes, avoidance of pump cavitation and prevention of boiling in the liquid. The sizing and design of such an accumulator requires very careful and accurate accounting of temperature distribution within each element of the working fluid for the entire range of conditions expected, accurate knowledge of volume of each fluid element, assessment of corresponding pressures needed to avoid boiling in the liquid, as well as the pressures needed to avoid cavitation in the pump. The appropriate liquid and accumulator strokes required to accommodate the liquid volume change, as well as the appropriate gas volumes, require proper sizing to ensure that the correct pressure range is maintained during the mission. Additionally, a very careful assessment of the process for charging both the gas side and the liquid side of the accumulator is required to properly position the bellows and pressurize the system to a level commensurate with requirements. To achieve the accurate sizing of the accumulator and the charging of the system, sophisticated EXCEL based spreadsheets were developed to rapidly come up with an accumulator design and the corresponding charging parameters. These spreadsheets have proven to be computationally fast and accurate tools for this purpose. This paper will describe the entire process of designing and charging the system, using a case study of the Mars Science Laboratory (MSL) fluid loops, which is en route to Mars for an August 2012 landing.

HRS↗

Energy Efficient Large-Scale Storage of Liquid Hydrogen

World’s largest LH2storage tanks constructed in mid-1960s at NASA/KSC. These vacuum-perlite insulated tanks, still in service today, are 3,200 m3capacity (ea.). In 2018, construction began on an additional 4,700 m3LH2storage tank at LC-39B•NASA’s new Space Launch System (SLS) heavy lift rocket for Artemis program holds 2,033 m3of LH2in its 8.4-m diameter by 40-m height. Two new energy-efficient technologies are included: glass bubbles insulation system and an Integrated Refrigeration and Storage (IRAS) heat exchanger for passive + active thermal control:•Evacuated glass bubbles insulation system has been shown to reduce LH2boiloff by 46% versus perlite in field demonstrations. Controlled storage via IRAS, when fully implemented, will provide full control of ullage pressure, zero boiloff, and even production of densified LH22CEC-2021

cryogenics↗

Design of the Heat Receiver for the U.S./Russia Solar Dynamic Power Joint Flight Demonstration

A joint U.S./Russia program is being conducted to develop, fabricate, launch, and operate a solar dynamic demonstration system on Space Station Mir. The goal of the program is to demonstrate and confirm that solar dynamic power systems are viable for future space applications such as the International Space Station Alpha The major components of the system include a heat receiver, a closed Brayton cycle power conversion unit, a power conditioning and control unit, a concentrator, a radiator, a thermal control system, and a Space Shuttle Carrier. This paper discusses the design of the heat receiver component. The receiver comprises a cylindrical cavity, the walls of which are lined with a series of tubes running the length of the cavity. The engine working fluid, a mixture of xenon and helium, is heated by the concentrated sunlight incident on these tubes. The receiver incorporates integral thermal storage, using a eutectic mixture of lithium fluoride and calcium difluoride as the thermal storage solid-to-liquid phase change materiaL This thermal storage is required to enable power production during eclipse. The phase change material is contained in a series of individual containment canisters.

Strumpf, Hal J.↗

Passive Charge Dissipating Work Function Matching Coating for Reducing Adhesion of Lunar Dust

The NASA Glenn Research Center Environmental Effects and Coatings Branch is developing a passive coating for lunar dust mitigation. This simple, transparent, conductive coating will be capable of reducing lunar dust adhesion to surfaces and dissipating surface charge. Anticipated benefits include compatibility with active dust mitigation strategies, improved efficiency and performance of solar cells and thermal control surfaces, and protection of astronauts and equipment on the lunar surface.

Lunar dust↗

Using Thermal Desktop to Determine Equivalent Solar Hours on Spacecraft Surfaces

Equivalent solar hours (ESH) are the duration of exposure of a surface to solar radiation, particularly ultraviolet (UV) radiation. Since UV light causes degradation to optical properties of thermal control surfaces, the determination of ESH is important to calculate end of life (EOL) optical properties for spacecraft external surfaces. A higher ESH value generally correlates to greater UV degradation experienced by the surface, resulting in an increase in solar absorptivity. This paper details a novel approach for calculating ESH using Thermal Desktop. Since the ESH value is useful for thermal analysts, this technique is beneficial to quickly perform the analysis internally with tools readily available without relying on external support and funding. The example presented in this paper shows how this method was developed and used for NASA's lunar Gateway spacecraft. This method of analysis is used to calculate ESH for the transit, assembly in orbit, and operational phases for Gateway, utilizing each of the program’s planned configurations throughout its 15-year lifetime. ESH values were calculated using the Monte-Carlo ray tracing capability of Thermal Desktop using both direct solar heating and indirect solar heating due to reflections from other surfaces. The output of this analysis includes an ESH gradient map across the spacecraft. Post-processing of these results enabled identification of the average and maximum ESH on critical surfaces such as radiators. The final ESH values for each surface are then used for determination of EOL optical properties.

Thermal Control↗

Theory and design of variable conductance heat pipes: Steady state and transient performance

Heat pipe technology pertinent to the design and application of self-controlled, variable conductance heat pipes for spacecraft thermal control is discussed. Investigations were conducted to: (1) provide additional confidence in existing design tools, (2) to generate new design tools, and (3) to develop superior variable conductance heat pipe designs. A computer program for designing and predicting the performance of the heat pipe systems was developed.

Edwards, D. K.↗

Thermal study of interface between the Orbiter cold plate and typical Shuttle spacecraft payload flight electronics

Spacelab provides a set of Freon line plumbing and cold plates for experiment equipments which are located in the Shuttle pallet and which need active thermal control. The reported study deals with the thermal problem of attaching a Command and Data Handling module with various electronic boxes whose combined footprints on the baseplate are much larger than the cold plate. A description of two modules and the cold plate assembly in the pallet is presented and a thermal model description is provided. The method employed in modeling heat pipes-honey-comb matrix is based upon an effective conductance between the heat pipe vapor and the walls of the heat pipe. The considered thermal models and a computer program are used to perform steady-state thermal analyses. The temperature gradients in the large module baseplate attached to the small cold plate are predicted as a function of the interface plate thickness.

Hwangbo, H.↗

Thermal Polymerization of N-Butyl Acrylate

Simple new polymerization method enables production of n-butyl acrylate polymer of desired high molecular weight, without disadvantages that usually attend more conventional methods. Process, which is hybrid of thermal, solution, and emulsion polymerization methods, involves controlled thermal polymerization of monomer at moderate temperatures without use of catalysts or additives.

Ingham, J. D.↗

The tethered retrievable platform concept and utilization

Main components of the current configuration of a proposed tethered satellite system (TSS) for deploying instrumentation up to 100 km upward or downward from the Orbiter in LEO are described. The TSS consists of the Deployer Module, the Tether, and the Satellite Module, and remains connected to the equipment in the Orbiter bay for the entire mission. The Deployer Module is mounted on a pallet, and has a boom, a tether control mechanism, and a tether control capability, in addition to data acquisition and control systems. The Satellite Module features a thermal control, electrical power and distribution, data management and communication, attitude determination, propulsion, and payload capability. Deployment is unpowered, taking advantage instead of gravity gradients to move the payload from the Orbiter. Safety features include a cutter mechanism to disengage the tether from the Orbiter if retrieval of the payload is judged to endanger the crew and the Orbiter.

Laue, J. H.↗

A unique exercise facility for simulating orbital extravehicular activity

A unique exercise facility has been developed and used to simulate orbital extravehicular activity (EVA). The device incorporates an arm ergometer into a mechanism which places the subject in the zero-g neutral body posture. The intent of this configuration is to elicit muscular, cardiovascular, respiratory, and thermoregulatory responses similar to those observed during orbital EVA. Experiments done with this facility will help characterize the astronaut's dynamic heat balance during EVA and will eventually lead to the development of an automated thermal control system which would more effectively maintain thermal comfort.

Williamson, Rebecca C.↗

Evaluation of space station ATCS evolution growth paths

This paper determines the feasibility of potential Active Thermal Control System (ATCS) growth paths by assessing thermal, integration, and implementation impacts. Thermal Radiation Analysis System/Infrared Radiation Transfer (TRASYS/IRTRAN) models were used to evaluate the effects of increased radiator temperature, increased radiator area, and radiator wing addition on Space Station Freedom (SSF) elements, including energy reflected back to the ATCS. Systems Improved Numerical Differencing Analyzer/Fluid Integrator (SINDA/FLUINT) models were used to determine the heat rejection capability of an ATCS loop with an integrated heat pump that operates with Electric Power System (EPS) peak power. The effects of upgrading the ATCS by advanced technology Orbital Replacement Unit (ORU) implementation during maintenance replacements was also evaluated. The study results presented lead to conclusions on which paths are best suited for different growth scenarios.

Ames, Brian E.↗

Internal Temperature Control For Vibration Testers

Vibration test fixtures with internal thermal-transfer capabilities developed. Made of aluminum for rapid thermal transfer. Small size gives rapid response to changing temperatures, with better thermal control. Setup quicker and internal ducting facilitates access to parts being tested. In addition, internal flows smaller, so less energy consumed in maintaining desired temperature settings.

Dean, Richard J.↗

Computer-Aided System Engineering and Analysis (CASE/A) Programmer's Manual, Version 5.0

The Computer Aided System Engineering and Analysis (CASE/A) Version 5.0 Programmer's Manual provides the programmer and user with information regarding the internal structure of the CASE/A 5.0 software system. CASE/A 5.0 is a trade study tool that provides modeling/simulation capabilities for analyzing environmental control and life support systems and active thermal control systems. CASE/A has been successfully used in studies such as the evaluation of carbon dioxide removal in the space station. CASE/A modeling provides a graphical and command-driven interface for the user. This interface allows the user to construct a model by placing equipment components in a graphical layout of the system hardware, then connect the components via flow streams and define their operating parameters. Once the equipment is placed, the simulation time and other control parameters can be set to run the simulation based on the model constructed. After completion of the simulation, graphical plots or text files can be obtained for evaluation of the simulation results over time. Additionally, users have the capability to control the simulation and extract information at various times in the simulation (e.g., control equipment operating parameters over the simulation time or extract plot data) by using "User Operations (OPS) Code." This OPS code is written in FORTRAN with a canned set of utility subroutines for performing common tasks. CASE/A version 5.0 software runs under the VAX VMS(Trademark) environment. It utilizes the Tektronics 4014(Trademark) graphics display system and the VTIOO(Trademark) text manipulation/display system.

Knox, J. C.↗

Solid-state Distributed Temperature Control for International Space Station

A newly developed solid-state temperature controller will offer greater flexibility in the thermal control of aerospace vehicle structures. A status of the hardware development along with its implementation on the Multi- Purpose Logistics Module will be provided. Numerous advantages of the device will also be discussed with regards to current and future flight vehicle implementations.

Holladay, Jon B.↗