SEARCH · Engineering Papers

Results for “Test Data Report”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,585 records · Page 88

All sources NASA NTRS DOE OSTI

NASA NTRS1981

Cell module and fuel conditioner development

The test results of and post test analysis of Stack 559 are reported. The design features and construction status of Stacks 560, 561, 562 and 563 are described. The measurements of cell materials compressibility are rationalized and summarized and an explanation of their uses is given. Preliminary results of a manifold material/coating survey are given. The results of shift converter catalyst performance tests and reforming catalyst aging tests are reported. State points for full load and part load operation of the fuel conditioning subsystem tabulated. Work on the data base for the fuel conditioner ancillary subsystems is summarized.

Hoover, D. Q., Jr.↗

NASA NTRS1981

Airborne antenna pattern calculations

Progress on the development of modeling software, testing software against caclulated data from program VPAP and measured patterns, and calculating roll plane patterns for general aviation aircraft is reported. Major objectives are the continued development of computer software for aircraft modeling and use of this software and program OSUVOL to calculate principal plane and volumetric radiation patterns. The determination of proper placement of antennas on aircraft to meet the requirements of the Microwave Landing System is discussed. An overview of the performed work, and an example of a roll plane model for the Piper PA-31T Cheyenne aircraft and the resulting calculated roll plane radiation pattern are included.

Knerr, T. J.↗

NASA NTRS1983

Properties of Nickel-Based Hydrogen-Turbine Blades

120 page report presents data on mechanical properties of cast nickelbased alloys for turbine blades operating in hydrogen and steam at high temperatures. Tests on alloys for hydrogen-burning engines of future are described.

Deluca, D. P.↗

NASA NTRS1982

QCSEE under-the-wing engine-wing-flap aerodynamic profile characteristics

As part of a broad-based NASA program to provide a technology base for future propulsion requirements for powered-lift aircraft, the Quiet, Clean, Short-Haul, Experimental Engine (QCSEE) program was begun by the Lewis Research Center in 1974. The initial buildup of the under-the-wing (UTW) engine was tested by the contractor at his test site. The UTW engine was delivered to Lewis in 1978 for further testing with wing and flap segments simulating an installation on a short-haul transport aircraft. The engine was also tested alone as an aid in identifying the various noise sources and their levels. As part of these tests the aerodynamic profiles at the exhaust nozzle and on the surfaces and in the wake of the wing-flap system were measured. This report documents, in plots and tabular form, the significant results from those tests. The results are presented as tabulations of aerodynamic data for all of the test points and as profiles of pressure, temperature, velocity, and normalized velocity and pressure for selected conditions. One of the main conclusions was that the measured flap surface temperatures were surprisingly low for both approach and takeoff flap settings.

Bloomer, H. E.↗

NASA NTRS1987

Environmental Testing of Glass-Fiber/Epoxy Pressure Vessels

Pair of reports discusses long-term environmental tests of glassfiber/epoxy composite pressure vessels. Strength diminishes during long exposure to environment. Since such data necessary for accurate design of long-life structures such as pressure vessels, NASA Lewis Research Center built outdoor test stand in 1973. Test stand maintains system under constant pressure loading without frequent intervention of personnel.

Faddoul, J. R.↗

NASA NTRS1991

Development of stitching reinforcement for transport wing panels

The NASA Advanced Composites Technology (ACT) program has the objective of providing the technology required to obtain the full benefit of weight savings and performance improvements offered by composite primary aircraft structures. Achieving the objective is dependent upon developing composite materials and structures which are damage tolerant and economical to manufacture. Researchers are investigating stitching reinforcement combined with resin transfer molding to produce materials meeting the ACT program objective. Research is aimed at materials, processes, and structural concepts for application in both transport wings and fuselages, but the emphasis to date has been on wing panels. Empirical guidelines are being established for stitching reinforcement in structures designed for heavy loads. Results are presented from evaluation tests investigating stitching types, threads, and density (penetrations per square inch). Tension strength, compression strength, and compression after impact data are reported.

Palmer, Raymond J.↗

NASA NTRS1935

Hydrodynamic Tests of Models of Seaplane Floats

This report contains the results of tank tests carried out at free trim on seventeen hulls and floats of various types. The data as to the weight on water, trim, and relative resistance for each model are plotted nondimensionally and are referenced both to the total weight and to the weight on water. Despite the fact that the experiments were not made systematically, a study of the models and of the test data permits nevertheless some general deductions regarding the forms of floats and their resistance. One specific conclusion is that the best models have a maximum relative resistance not exceeding 20 percent of the total weight.

Eula, Antonio↗

NASA NTRS2000

Additional Testing of the DHC-6 Twin Otter Tailplane Iced Airfoil Section in the Ohio State University 7x10 Low Speed Wind Tunnel

The need for fundamental research in Ice Contaminated Tailplane Stall (ICTS) was established through three international conferences sponsored by the FAA. A joint NASA/FAA Tailplane Icing Program was formed in 1994 with the Ohio State University playing a critical role for wind tunnel and analytical research. Two entries of a full-scale 2-dimensional tailplane airfoil model of a DHC-6 Twin Otter were made in The Ohio State University 7x10 ft wind tunnel. This report describes the second test entry that examined additional ice shapes and roughness, as well as airfoil section differences. The addition data obtained in this test fortified the original database of aerodynamic coefficients that permit a detailed analysis of flight test results with an OSU-developed analytical program. The testing encompassed a full range of angles of attack and elevator deflections at flight Reynolds number conditions. Aerodynamic coefficients, C(L), C(M), and C(He), were obtained by integrating static pressure coefficient, C(P), values obtained from surface taps. Comparisons of clean and iced airfoil results show a significant decrease in the tailplane aeroperformance (decreased C(Lmax), decreased stall angle, increased C(He)) for all ice shapes with the grit having the lease affect and the LEWICE shape having the greatest affect. All results were consistent with observed tailplane stall phenomena and constitute an effective set of data for comprehensive analysis of ICTS.

Gregorek, Gerald↗

NASA NTRS2001

Smoldering, Transition and Flaming in Microgravity

A research project is underway to study smolder and the transition to flaming in microgravity. The Microgravity Smoldering Combustion (MSC) flight project is an ongoing research project to provide a better understanding of the controlling mechanisms of smoldering combustion. The Smoldering Transition and Flaming (STAF) project is a recently established research program that will utilize the Fluids and Combustion Facility (FCF) of the ISS to examine the transition from smolder to flaming in microgravity. In forced flow smolder experiments ambient pressure in the MSC chamber rises, thus motivating the need to understand the effects of pressure on smoldering combustion. Further, the STAF experiment has constraints on experimental scale and testing at elevated pressure may be a mechanism to reduce the sample size by enhancing the smolder reaction. In the work we are reporting here, a series of ground-based tests determine the effects of pressure on smoldering combustion. These tests are compared with data obtained from experiments conducted aboard the Space Shuttle in flights STS-69 and STS-77. Measurements of one-dimensional smolder propagation velocity are made by thermocouple probing and a non-intrusive Ultrasound Imaging System (UIS)]. Thermocouples are also used to obtain reaction temperatures and the UIS is used to determine permeabilities of the fuel in real-time.

Fernandez-Pello, A. C.↗

NASA NTRS2004

Passive Measurement of CO2 Column from an Airborne Platform

We are in the third and final year of our IIP funding to develop a sensor for very precise determination of the CO2 Column. Global measurements of this sort from a satellite platform are needed to improve our understanding of the global carbon budget. In previous reports to this meeting we have described the method by which this system operates and presented data taken during ground based tests of the instrument. Work in the final year has concentrated on building the flight hardened version of the instrument that will be used in our field trials on the Dryden DC-8. The flight unit represents an integration of three channels into a single instrument. These three channels are the CO2 channel, the oxygen pressure sensing channel, and the oxygen temperature sensing channel. Integration of the three channels into a single unit significantly decreases the size of the instrument. The flight unit also employs more rugged optical mounts and integrated optical shielding. Light enters the instrument from below first striking the right angled mirror shown extending over the edge of the platform. The light is then focused through a pinhole to define the instrument field of view, chopped and recollimated. Dichroic mirrors are used to separate the CO2 wavelength from the O2 wavelength and that light is further divided by a 50-50 beamsplitter between the 2 oxygen channels - the pressure channel and the temperature channel. The six white boxes contain the detectors for each of the three channels. The detectors on the left in the photo serve the reference channels and the detectors on the right are for the Fabry-Perots. CO2 is measured by the pair of detectors farthest from the viewer. Pressure via O2 is detected by the central pair of detectors. The closest pair is used to determine temperature via O2.

Heaps, William S.↗

NASA NTRS2006

Orbiting GPS Receiver Modified to Track New L2C Signal

The L2C signal is a great step forward for civil applications of GPS, enabling high-accuracy dual-frequency measurements. Engineers from the Jet Propulsion Laboratory and ITT teamed to reprogram FPGA firmware and add tracking software on an orbiting receiver to track the new GPS L2C signal from SAC-C. SAC-C is an Argentinean science satellite and was launched in November 2000 with a BlackJack GPS receiver. This is a dual-frequency digital receiver with 48 tracking channels and four antennas. On SAC-C, it provides precise orbits, atmospheric occultation data, tests of GPS surface reflections, and serves as an orbiting test bed for new GPS development such as the L2C tracking reported here.

GPS receiver↗

NASA NTRS1942

Supplementary Spin Tests of a 1/20-Scale Model of the Bell XP-39E Airplane

As a result of the loss of the first XP-39E airplane due to an uncontrolled spin, and at the request of the War Department received in their letter to the NACA, March 31, 1942, additional tests have been made of the corresponding 1/20-scale spin-tunnel model. Tests were made for the normal full load condition and also for the loading condition corresponding to that of the airplane at the time of the crash, that Is, with guns, ammunition, and half of the fuel removed from the wings. The model tests were made with the tail arrangement corresponding to that of the airplane at the time of the crash, as well as with numerous modified tail and contour arrangements In an attempt to evolve satisfactory recovery characteristics. The tests were started on April 2, 1942, and completed in approximately two weeks, with the development of several alternate tail arrangements giving reasonably satisfactory recoveries for normal spinning control configuration. The tests were witnessed by Mr. Melvin Shorr, of the Materiel Center at Wright Field, and Mr. Paul C. Emmons, of the Bell Aircraft Corporation, to whom records of the test data were furnished. Colonel H. P. Swofford, of the Materiel Center, Wright Field, also witnessed part of the tests. A preliminary report of the results of the tests has been forwarded to the Materiel Command at Wright Field. A brief check of the parachute installation for the airplane was also made.

A I Neihouse↗

NASA NTRS2021

On-Board Model Based Fault Diagnosis for CubeSat Attitude Control Subsystem: Flight Data Results

Self-sufficient, robotic spacecraft require estimates of their hardware health state in order to project future system state and plan actions toward achieving mission goals. In this paper, we report on integration of a Model-Based Fault Diagnosis (MBFD) model and reasoning engine into flight software leveraging the Arcsecond Space Telescope Enabling Research in Astrophysics (ASTERIA) mission, including test results against captured flight data using the ASTERIA system testbed. Our effort integrated the Model-based Off-Nominal State Identification and Detection (MONSID) model-based reasoning system, developed by Okean Solutions, into ASTERIA flight software using the F Prime software framework. The MONSID engine was supplied with a model of the Blue Canyon Technologies XACT attitude control system (ACS) and tested against flight data and seeded fault tests. While we were unable to conduct an on-board experiment due to the premature loss of ASTERIA, our effort proved the feasibility of on-board model-based fault management, demonstrating reliable and accurate diagnosis using captured data, and further supporting a closed-loop spacecraft autonomy demonstration including autonomous navigation in off-nominal conditions.

Prather, Maurice↗

NASA NTRS1997

Effects of Applied Strain on Rates of Ageing: Project Overview

One of the stated intents of this project has been to make some assessment of effects of strain on rates of ageing of project thermoplastics exposed to project fluids. To this end, certain straining jigs which apply in various modes - tensile, four-point bending and crack growth using compact tension samples - were designed and made for holding samples during fluid exposures. During testing, features of the thermoplastics have been observed which have tended to confuse apparent strain effects on the polymers' aged performance, but recent assessments of the topic and its data have led to considerable progress being made in identifying test procedures necessary for strain and related effects on chemical deterioration to manifest themselves. It is the intent of this report to provide a summary of what has been determined on strain and related effects thus far, and provide recommendations for clarifying them in Phase 2 by means of further test procedures which will increase and focus the severity of the conditions applying. The choice of flexible pipe rather than umbilicals service for assessing service strain conditions reflects the major interest of project members. However, Tefzel data are still provided.

Campion, R. P.↗

NASA NTRS1996

Mir Cooperative Solar Array Project Accelerated Life Thermal Cycling Test

The Mir Cooperative Solar Array (MCSA) project was a joint U.S./Russian effort to build a photovoltaic (PV) solar array and deliver it to the Russian space station Mir. The MCSA will be used to increase the electrical power on Mir and provide PV array performance data in support of Phase 1 of the International Space Station. The MCSA was brought to Mir by space shuttle Atlantis in November 1995. This report describes an accelerated thermal life cycle test which was performed on two samples of the MCSA. In eight months time, two MCSA solar array 'mini' panel test articles were simultaneously put through 24,000 thermal cycles. There was no significant degradation in the structural integrity of the test articles and no electrical degradation, not including one cell damaged early and removed from consideration. The nature of the performance degradation caused by this one cell is briefly discussed. As a result of this test, changes were made to improve some aspects of the solar cell coupon-to-support frame interface on the flight unit. It was concluded from the results that the integration of the U.S. solar cell modules with the Russian support structure would be able to withstand at least 24,000 thermal cycles (4 years on-orbit). This was considered a successful development test.

Hoffman, David J.↗

DOE OSTI2021

Report on FY 2021 Fabrication and Testing of Qualified Alloy 709 Welds at ORNL

Alloy 709 is a candidate construction material for the Sodium Fast Reactor (SFR). As part of the Alloy 709 ASME Code Case development team under the Advanced Reactor Technologies (ART) Program, this work covers the development of the technical basis for weld fabrication and weld qualification of Alloy 709. This report summarizes the research conducted in FY 2021 and relevant results from previous reporting periods, aimed at welding commercial heat of Alloy 709 plates of relatively high phosphorous (P) level in support of ASME code case data package. Welding, code qualification tests, and associated microstructure characterization were carried out in determining the effect of P levels of weld wire on the weldability of the high P commercial heat of Alloy 709. The Alloy 709 weld creep strength was evaluated though preliminary creep testing.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

NASA NTRS2011

Innovative Comparison of Transient Ignition Temperature at the Booster Interface, New Stainless Steel Pyrovalve Primer Chamber Assembly "V" (PCA) Design Versus the Current Aluminum "Y" PCA Design

An assessment of four spacecraft pyrovalve anomalies that occurred during ground testing was conducted by the NASA Engineering & Safety Center (NESC) in 2008. In all four cases, a common aluminum (Al) primer chamber assembly (PCA) was used with dual NASA Standard Initiators (NSIs) and the nearly simultaneous (separated by less than 80 microseconds) firing of both initiators failed to ignite the booster charge. The results of the assessment and associated test program were reported in AIAA Paper AIAA-2008-4798, NESC Independent Assessment of Pyrovalve Ground Test Anomalies. As a result of the four Al PCA anomalies, and the test results and findings of the NESC assessment, the Mars Science Laboratory (MSL) project team decided to make changes to the PCA. The material for the PCA body was changed from aluminum (Al) to stainless steel (SS) to avoid melting, distortion, and potential leakage of the NSI flow passages when the device functioned. The flow passages, which were interconnected in a Y-shaped configuration (Y-PCA) in the original design, were changed to a V-shaped configuration (V-PCA). The V-shape was used to more efficiently transfer energy from the NSIs to the booster. Development and qualification testing of the new design clearly demonstrated faster booster ignition times compared to the legacy AL Y-PCA design. However, the final NESC assessment report recommended that the SS V-PCA be experimentally characterized and quantitatively compared to the Al Y-PCA design. This data was deemed important for properly evaluating the design options for future NASA projects. This test program has successfully quantified the improvement of the SS V-PCA over the Al Y-PCA. A phase B of the project was also conducted and evaluated the effect of firing command skew and enlargement of flame channels to further assist spacecraft applications.

Saulsberry, Regor L.↗

NASA NTRS1993

Performance and rotor loads measurements of the Lynx XZ170 helicopter with rectangular blades

This report presents the results of a series of flight tests on the Lynx XZ170 helicopter with rectangular blades. The test objectives were to explore the flight envelope and to measure the performance and structural loads of the Lynx main-rotor system. The tests were conducted as part of the British Experimental Rotor Program (BERP) under a contract with the Ministry of Defense in England. Data were acquired for steady-level flights at five weight coefficients. Some flight conditions were tested at beyond the retreating-blade stall boundary, which was defined by a predetermined limit on the pitchlink vibratory load. In addition to documenting the flight conditions and data, this report describes the aircraft, particularly the rotor system, in detail.

Lau, Benton H.↗