Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Surfaced Polymers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,585 records · Page 88

Preparation and analysis of multilayer composites based on polyelectrolyte complexes

A method for preparing multilayer film composites based on chitosan has been developed by the example of polymer pairs: chitosan–hyaluronic acid, chitosan–alginic acid, and chitosan–carrageenan. The structure of the composite films is characterized by X-ray diffractometry and scanning electron microscopy. It is shown that the deposition of a solution of hyaluronic acid, alginic acid, or carrageenan on a chitosan gel film leads to the formation of a polyelectrolyte complex layer at the interface, which is accompanied by the ordering of chitosan chains in the surface region; the microstructure of this layer depends on the nature of contacting polymer pairs.

60 APPLIED LIFE SCIENCES↗

Toward Optimizing Electrospun Nanofiber Fuel Cell Catalyst Layers: Polymer–Particle Interactions and Spinnability

We investigate the effect of the poly(acrylic acid) (PAA) carrier polymer concentration on the microstructure and rheological properties of catalyst inks for electrospun polymer–electrolyte membrane fuel-cell catalyst layers. Characterization of an ink microstructure using oscillatory shear rheology showed that the catalyst particles (platinum on carbon) are significantly agglomerated in the absence of PAA or an ionomer. Both the ionomer and PAA promoted the stability of the particles against agglomeration via electrosteric stabilization by adsorbing onto the particle surface. Increasing the PAA concentration increased the stability of the particles (or reduced the agglomerated structure) due to increasing PAA coverage onto the free surface area of the particles. However, beyond a certain increase in concentration, PAA was found to predominantly remain as an excess free polymer in the ink due to an insufficient free/available surface area on the particles for further PAA coverage. Extensional rheology measurements demonstrated that PAA enhances the extensional viscosities of the inks. Consequently, increasing the PAA concentration in the ink promoted the evolution of uniform nanofibers. However, beyond a certain concentration, a significant increase in the shear viscosities of the inks led to defective fiber morphologies because of the onset of flow instabilities. Electrochemical performance comparisons between catalyst layers with different PAA concentrations showed maximum performance at the PAA concentration that led to the least agglomerated structure of the catalyst, most uniform fiber morphologies, and low concentrations of free (non-adsorbing) PAA in the electrode. These results provide a rationale for optimization of electrospun catalyst nanofibers for both spinnability and electrochemical performance.

25 ENERGY STORAGE↗

Fabrication Methods for Adaptive Deformable Mirrors

Previously, it was difficult to fabricate deformable mirrors made by piezoelectric actuators. This is because numerous actuators need to be precisely assembled to control the surface shape of the mirror. Two approaches have been developed. Both approaches begin by depositing a stack of piezoelectric films and electrodes over a silicon wafer substrate. In the first approach, the silicon wafer is removed initially by plasmabased reactive ion etching (RIE), and non-plasma dry etching with xenon difluoride (XeF2). In the second approach, the actuator film stack is immersed in a liquid such as deionized water. The adhesion between the actuator film stack and the substrate is relatively weak. Simply by seeping liquid between the film and the substrate, the actuator film stack is gently released from the substrate. The deformable mirror contains multiple piezoelectric membrane layers as well as multiple electrode layers (some are patterned and some are unpatterned). At the piezolectric layer, polyvinylidene fluoride (PVDF), or its co-polymer, poly(vinylidene fluoride trifluoroethylene P(VDF-TrFE) is used. The surface of the mirror is coated with a reflective coating. The actuator film stack is fabricated on silicon, or silicon on insulator (SOI) substrate, by repeatedly spin-coating the PVDF or P(VDFTrFE) solution and patterned metal (electrode) deposition. In the first approach, the actuator film stack is prepared on SOI substrate. Then, the thick silicon (typically 500-micron thick and called handle silicon) of the SOI wafer is etched by a deep reactive ion etching process tool (SF6-based plasma etching). This deep RIE stops at the middle SiO2 layer. The middle SiO2 layer is etched by either HF-based wet etching or dry plasma etch. The thin silicon layer (generally called a device layer) of SOI is removed by XeF2 dry etch. This XeF2 etch is very gentle and extremely selective, so the released mirror membrane is not damaged. It is possible to replace SOI with silicon substrate, but this will require tighter DRIE process control as well as generally longer and less efficient XeF2 etch. In the second approach, the actuator film stack is first constructed on a silicon wafer. It helps to use a polyimide intermediate layer such as Kapton because the adhesion between the polyimide and silicon is generally weak. A mirror mount ring is attached by using adhesive. Then, the assembly is partially submerged in liquid water. The water tends to seep between the actuator film stack and silicon substrate. As a result, the actuator membrane can be gently released from the silicon substrate. The actuator membrane is very flat because it is fixed to the mirror mount prior to the release. Deformable mirrors require extremely good surface optical quality. In the technology described here, the deformable mirror is fabricated on pristine substrates such as prime-grade silicon wafers. The deformable mirror is released by selectively removing the substrate. Therefore, the released deformable mirror surface replicates the optical quality of the underlying pristine substrate.

Toda, Risaku↗

Multilayered Glass Fibre-reinforced Composites In Rotational Moulding

The potential of multiple layer fibre-reinforced mouldings is of growing interest to the rotational moulding industry because of their cost/performance ratio. The particular problem that arises when using reinforcements in this process relate to the fact that the process is low shear and good mixing of resin and reinforcement is not optimum under those conditions. There is also a problem of the larger/heavier reinforcing agents segregating out of the powder to lay up on the inner part surface. In this study, short glass fibres were incorporated and distributed into a polymer matrix to produce fibre-reinforced polymer composites using the rotational moulding process and characterised in terms of morphology and mechanical properties.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Long-term chemothermal stability of delithiated NCA in polymer solid-state batteries

Here, the long-term chemothermal stability of chemically delithiated Li 0.3 Ni 0.8 Co 0.15 Al 0.05 O 2 (Li 0.3 NCA) was systematically investigated at relevant operating temperatures of polymer solid-state batteries using ex situ synchrotron-based hard and soft X-ray absorption spectroscopy. The reduction of nickel on the surface, subsurface, and in the bulk of secondary NCA particles was studied and directly related to aging time, temperature, the presence of polymeric electrolyte (poly(ethylene oxide) or polycaprolactone), and lithium salt (lithium tetrafluoroborate or lithium bis(trifluoromethanesulfonyl)imide). Depending on the polymer and/or lithium salt accompanying the delithiated Li 0.3 NCA, reduction of nickel at the surface, subsurface, and bulk occurs to varying extents, starting at the surface and propagating into the bulk material. Our findings predict how degradation (reduction of nickel) is strongly correlated to temperature, time, and the presence of blended polymer and/or lithium salt in the cathode. The relative stability of the NCA material in cathodes having different polymer and lithium salt combinations identified in the ex situ spectroscopy study is directly demonstrated in solid-state polymer batteries.

25 ENERGY STORAGE↗

Minerals as Molecules—Use of Aqueous Oxide and Hydroxide Clusters to Understand Geochemical Reactions

Large aqueous oxide ions as minerals! Minerals dissolve by repeated ligand exchange reactions and geochemists use polyoxometalate ions to establish structure–reactivity relations for environmentally important functional groups. Here, for example, are plotted the dissolution rates of two classes of minerals against rates of solvent exchanges around the corresponding aquo ions. Here, geochemists and environmental chemists make predictions about the fate of chemicals in the shallow earth over enormously long times. Key to these predictions is an understanding of the hydrolytic and complexation reactions at oxide mineral surfaces that are difficult to probe spectroscopically. These minerals are usually oxides with repeated structural motifs, like silicate or aluminosilicate polymers, and they expose a relatively simple set of functional groups to solution. The geochemical community is at the forefront of efforts to describe the surface reactivities of these interfacial functional groups and some insights are being acquired by using small oligomeric oxide molecules as experimental models. These small nanometer-size clusters are not minerals, but their solution structures and properties are better resolved than for minerals and calculations are relatively well constrained. The primary experimental data are simple rates of steady oxygen-isotope exchanges into the structures as a function of solution composition that can be related to theoretical results. There are only a few classes of large oxide ions for which data have been acquired and here we review examples and illustrate the general approach, which also derives directly from the use of model clusters to understand for the active core of metalloenzymes in biochemistry.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Infusible silazane polymer and process for producing same

Coatings of high thermal and chemical stability for application to metal, glass, ceramics, and other surfaces are formed by reacting diphenyldichlorosilane in the presence of triethylamine with a nitrogen base selected from the group consisting of ammonia and methylamine. The pl polymeric, noncrystalline reaction product is heated in a reaction zone open to the atmosphere at a temperature ranging from approximately 250 C to 450 C until the infusible polymer is formed.

Burks, R. E., Jr.↗

Nafion Structural Phenomena at the Platinum and Carbon Interfaces

Neutron Reflectometry (NR) was used to examine the interactions of Polymer Electrolyte Fuel Cell (PEFC) materials that comprise the triple-phase interface. Smooth, idealized layers of Nafion on glassy carbon (GC) and Pt surfaces were used to experimentally model the PEFC electrode interfaces. Different multilayer structures of Nafion were found in contact with the Pt or GC surfaces. These structures showed separate hydrophobic and hydrophilic domains formed within the Nafion layer when equilibrated with saturated D2O vapor. A hydrophobic Nafion region was formed adjacent to a Pt film. However, when Nafion was in contact with a PtO surface, the Nafion at the Pt interface became hydrophilic. The adsorbed oxide layer caused a long-range restructuring of the perfluorosulfonic acid (PFSA) polymer chains that comprise Nafion . The thicknesses of the hydrophobic and hydrophilic domains changed to the same magnitude when the oxide layer was present compared to a thin hydrophobic domain in contact with Pt. A three-layer Nafion structure was formed when Nafion was in direct contact with GC. The findings in this research are direct experimental evidence that both the interfacial and long-range structural properties of Nafion are affected by the material with which it is in contact. Evidence of physical changes of aged Nafion films was obtained, and the results showed a permanent increase in the thickness of the Nafion film and a decrease in scattering length density (SLD), which are attributed to irreversible swelling of the Nafion film. The aging also resulted in a decrease in SLD of the GC substrate, which is likely due to either an increase in surface oxidation of the carbon or loss of carbon mass at the GC surface.

30 DIRECT ENERGY CONVERSION↗

Sequential Infiltration Synthesis of Multinary Metal Oxides: The Role of Precursor Diffusion and Reactivity

Understanding volatile metal–organic precursor transport in polymer matrices during sequential infiltration synthesis (SIS) is critical to the design of hybrid materials of tailored composition and uniform structure. Here, we investigate the diffusion and reaction behavior of diethylzinc (DEZ) in poly(methyl methacrylate) (PMMA) matrices with variable indium and zinc incorporation. Unlike conventional SIS where precursors adduct or react directly with the polymer backbone, DEZ shows minimal interaction with PMMA. However, DEZ may interact strongly with In–OH or Zn–OH moieties that are previously incorporated into a PMMA thick film. Using spectroscopic ellipsometry, X-ray photoelectron spectroscopy depth profiling, and EDX line scans, we quantify Zn incorporation as a function of exposure time, polymer thickness, and previous infiltration steps. The Zn distribution evolves from surface-localized to deep within the ∼1 μm thick film with increasing DEZ exposures up to 30 min. A reaction-diffusion model incorporating a hindering factor to capture diffusivity decay due to product accumulation reproduces the Zn depth profile and yields physically meaningful parameters to guide future growth. Furthermore, this study provides a framework for interpreting metal–organic precursor infiltration behavior and highlights the utility of model-guided SIS process design.

diethylzinc↗

Air-stable solution-processed n-channel organic thin film transistors with polymer-enhanced morphology

N,N′-1H,1H-perfluorobutyl dicyanoperylenecarboxydiimide (PDIF-CN{sub 2}) is an n-type semiconductor exhibiting high electron mobility and excellent air stability. However, the reported electron mobility based on spin-coated PDIF-CN{sub 2} film is much lower than the value of PDIF-CN{sub 2} single crystals made from vapor phase deposition, indicating significant room for mobility enhancement. In this study, various insulating polymers, including poly(vinyl alcohol), poly(methyl methacrylate) (PMMA), and poly(alpha-methylstyrene) (PαMS), are pre-coated on silicon substrate aiming to enhance the morphology of the PDIF-CN{sub 2} thin film, thereby improving the charge transport and air stability. Atomic force microscopy images reveal that with the pre-deposition of PαMS or PMMA polymers, the morphology of the PDIF-CN{sub 2} polycrystalline films is optimized in semiconducting crystal connectivity, domain size, and surface roughness, which leads to significant improvement of organic thin-film transistor (OTFT) performance. Particularly, an electron mobility of up to 0.55 cm{sup 2}/V s has been achieved from OTFTs based on the PDIF-CN{sub 2} film with the pre-deposition of PαMS polymer.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Evaluation of surface damage on organic materials irradiated with Ar cluster ion beam

The sputtering yields of organic materials under large cluster ion bombardment are much higher than those under conventional monomer ion bombardment. The sputtering rate of arginine remains constant with fluence for an Ar cluster ion beam, but decreases with fluence for Ar monomer. Additionally, because Ar cluster etching induces little damage, Ar cluster ion can be used to achieve molecular depth profiling of organic materials. In this study, we evaluated the damage to poly methyl methacrylate (PMMA) and arginine samples irradiated with Ar atomic and Ar cluster ion beams. Arginine samples were analyzed by secondary ion mass spectrometry (SIMS) and PMMA samples were analyzed by X-ray photoelectron spectroscopy (XPS). The chemical structure of organic materials remained unchanged after Ar cluster irradiation, but was seriously damaged. These results indicated that bombardment with Ar cluster ions induced less surface damage than bombardment with Ar atomic ion. The damage layer thickness with 5 keV Ar cluster ion bombardment was less than 1 nm.

36 MATERIALS SCIENCE↗

Synthesis and characterization of ionic liquid (EMImBF{sub 4})/Li{sup +} - chitosan membranes for ion battery

Lithium ion battery has been currently developed and produced because it has a longer life time, high energycapacity, and the efficient use of lithium ion battery that is suitable for storing electrical energy. However, this battery has some drawbacks such as use liquid electrolytes that are prone to leakage and flammability during the battery charging process in high temperature. In this study, an ionic liquid 1-ethyl-3-methylimidazolium tetrafluoroborate (EMImBF4) containing Li{sup +} ions was synthesized and combined with chitosan polymer host as a polymer electrolyte membrane for lithium-ion batteries to solve this problems. This ionic liquid was obtained from the anion metathesis reaction between EMImBr and LiBF4 salt, while EMImBr was synthesized from the reaction between 1-methylimidazole and ethyl bromide utilizing Microwave Assisted Organic Synthesis (MAOS) method. The ionic liquid obtained was characterized by microstructure analysis with using NMR and FTIR spectroscopy. The polymer electrolyte membrane was characterized by analysis functional groups (FTIR), ionic conductivity (EIS), and surface morphology (SEM). The analysis results of ion conductivity by the EIS method showed the increase the ionic conductivity value of membranes from 1.30 × 10{sup −2} S cm{sup −1} for chitosan to 1.30 × 10{sup −2} S cm{sup −1} for chitosan with EMImBF4/Li{sup +}, and this result was supported by analysis the surface morphology (SEM)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Trace Adsorptive Removal of PFAS from Water by Optimizing the UiO‐66 MOF Interface

Abstract The confluence of pervasiveness, bioaccumulation, and toxicity in freshwater contaminants presents an environmental threat second to none. Exemplifying this trifecta, per‐ and polyfluoroalkyl substances (PFAS) present an alarming hazard among the emerging contaminants. State‐of‐the‐art PFAS adsorbents used in drinking water treatment, namely, activated carbons and ion‐exchange resins, are handicapped by low adsorption capacity, competitive adsorption, and/or slow kinetics. To overcome these shortcomings, metal–organic frameworks (MOFs) with tailored pore size, surface, and pore chemistry are promising alternatives. Thanks to the compositional modularity of MOFs and polymer–MOF composites, herein we report on a series of water‐stable zirconium carboxylate MOFs and their low‐cost polymer‐grafted composites as C 8 –PFAS adsorbents with benchmark kinetics and “parts per billion” removal efficiencies. Bespoke insights into the structure–function relationships of PFAS adsorbents are obtained by leveraging interfacial design principles on solid sorbents, creating a synergy between the extrinsic particle surfaces and intrinsic molecular building blocks.

Ilić, Nebojša↗

Quantification of [MTBD][beti] loading and its effects on Pt/HSC electrode performance in hydrogen fuel cells

High surface area carbon-supported platinum catalysts (Pt/HSC) are widely used in polymer electrolyte membrane fuel cells but often suffer from limited proton and oxygen transport within porous domains. To address these challenges, we integrate the ionic liquid [MTBD][beti] into Pt/HSC catalyst layers using two deposition methods-one-pot and sequential deposition-to tune IL distribution within micropores and mesopores. A combination of ex situ and in operando techniques were employed to elucidate electrode structure-performance relationships across a range of IL loadings. Sequential deposition achieved more efficient pore filling and higher IL retention at lower IL:C ratios, enabling enhanced proton conductivity and protection of active sites. Compared to the IL-free Pt/HSC, IL-modified electrodes demonstrated up to 28% improvement in mass activity and enhanced high-current-density performance under low relative humidity, while maintaining comparable performance under humidified conditions. Electrochemical impedance spectroscopy and CO displacement experiments reveal that improvements are linked to reduced ionic resistance and lower sulfonate adsorption on Pt sites, rather than changes in electrochemical surface area. However, excessive IL loading leads to mass transport losses. These results highlight the importance of selective pore filling and efficient IL distribution in achieving kinetic gains without compromising ionic and gas transport.

08 HYDROGEN↗

Fixation of virgin lunar surface soil

Two systems are shown to be suitable for fixing loose particulate soils with a polymer film, without visually detectable disturbance of the soil particle spatial relationships. A two-component system is described, which uses a gas monomer condensible at the soil temperature and a gas phase catalyst acting to polymerize the monomer. A one-component system using a monomer which polymerizes spontaneously on and within the top few millimeters of the soil is also considered. The two-component system employs a simpler apparatus, but it operates over a narrower temperature range (approximately -40 to -10 C). Other two-component systems were identified which may operate at soil temperatures as high as +100 C, at relatively narrow temperature ranges of approximately 30 C. The one-component system was demonstrated to operate successfully with initial soil temperatures from -70 C or lower to +150 C.

Conley, J. M.↗