Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Performance Gap”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,585 records · Page 88

Compatibility of polymers in super-critical carbon dioxide for power generation systems: High level findings for low temperatures and pressure conditions

Polymers such as PTFE (polytetrafluorethylene or Teflon), PEEK (polyetheretherketone), EPDM (ethylene propylene cliene monomer) rubber, Viton, EPR (ethylene propylene rubber), Nylon, Nitrile rubber, and perfluoroelastomers are commonly employed in super critical CO 2 (sCO2) energy conversion systems. O-rings and gaskets made from these polymers face stringent performance conditions such as elevated temperatures, high pressures, pollutants and corrosive humid environments. Critical knowledge gaps about polymer degradation from sCO2 exposure need to be addressed. To understand these effects, we have studied nine commonly used polymers subjected to elevated temperatures under isobaric conditions of sCO2 pressure. The polymers (PEEK, Nylon, PTFE, EPDM, Nitrile rubber, EPR, Neoprene, perfluoroelastomer FF 202 and Viton) were exposed for 1000 hours at 100°C to 25 MPa sCO2 pressure in an autoclave. In a second study, elastomers perfluoroelastomer (FF202) and EPDM were exposed to 25 MPa sCO2 for 1000 hours at 150°C. Samples were extracted for ex-situ characterization at t = 200 hours and then at the completion of the test at t=1000 hours. The polymer samples were examined for physical and chemical changes by Dynamic Mechanical and Thermal Analysis (DMTA), Fourier Transform Infrared (FTIR) spectroscopy, and compression set. Density and mass changes immediately after removal from test and 48 hours later, and optical microscopy techniques were also used. Microcomputer tomography (micro CI) data was generated on select specimens. Super-critical CO 2 effects have been identified as either physical or chemical effects. For each polymer, the dominance of one type of effect over the other was evaluated. Attempts were also made to qualitatively link sCO2 effects such as lowering or increase in glass transition temperatures, storage modulus changes, mass and compression set changes, chemical changes seen in FTIR analyses and blister and void formation seen post-exposure to polymer microstructure-related mechanisms such as plasticization of the polymer matrix, escape of volatiles from the polymer during depressurization, and filler and plasticizer effects on microstructure with rapid depressurization rates.

36 MATERIALS SCIENCE↗

Heat Integration Optimization and Dynamic Modeling Investigation for Advancing the Coal-Direct Chemical Looping Process

The purpose of the project is to address the optimization and startup operation of a modular coal direct chemical looping (CDCL) combustion system integrated with a steam cycle for power generation to reduce the risks involved in further scale-up of the technology. The modular reactor design of the CDCL process provides flexibility in the fabrication of the reactor and in its operating capacity (i.e. turndown ratio) at the cost of a more complex heat exchange network (HEN) design and integration. To address the technology gaps and advance the efficiency and economic feasibility of the CDCL technology, the project will perform a detailed and comprehensive analysis of the integration of a modular CDCL reactor system and a steam cycle system under both static and transient conditions via HEN process performance simulations and system dynamic modeling, respectively. The scope of work consists of 1) Experimental and computational studies of the CDCL combustor reactor 2) Comprehensive static (i.e. steady-state) system HEN design analysis in CDCL 550 MWe commercial unit for power generation and 3) Dynamic modeling of site specific design of 10MWe CDCL large pilot plant. The project team has successfully developed and validated a kinetic model for the oxidation of oxygen carriers in the combustor using the unreacted shrinking core model (UCSM). The model is capable of capturing the oxidation kinetics of fully or partially reduced oxygen carrier particles. A computational fluid dynamics (CFD) model is developed to simulate the hydrodynamics, heat transfer, and chemical reaction occurring in the CDCL combustor. The model is developed in MFIX and ANSYS Fluent. Key aspects of CDCL combustor operation, including heat transfer, oxygen carrier oxidation, and the transport of oxygen carrier particles, are simulated using this CFD model. The HEN for a commercial scale 550 MWe CDCL power plant is simulated and optimized using ASPEN Plus. Practical design considerations are incorporated based on industrial experiences. The performance and cost for the commercial CDCL plant is updated based on these analyses. A dynamic model for the 10 MWe CDCL pilot plant is developed in ProTRAX simulation software. The model is based on the pilot plant design developed in project DE-FE0027654 “10 MWe CDCL Large Pilot Plang – Pre-FEED Study” and the steam cycle data obtained from Dover Light & Power plant. The transient behaviors during pilot plant load variation are simulated using the dynamic model.

01 COAL, LIGNITE, AND PEAT↗

Capability Enhancements for System-level thermal Hydraulic Modeling of Lead Fast Reactors

This project has focused on the use, assessment, and development of the SAS4A/SASSYS-1 (SAS) safety analysis software. Although SAS was originally intended as a safety analysis tool for Liquid Metal cooled Fast Reactors (LMFRs), which includes both Sodium Fast Reactors (SFRs) and Lead Fast Reactors (LFRs), the vast majority of its recent development and customization has been tailored to SFRs. In general, enhancements that are made to the software for SFRs are applicable to LFRs, however, the fuel composition and corrosive nature of lead requires careful consideration when performing safety analysis of an LFR. In this project an emphasis was placed on closing gaps that are associated with modeling LFRs using SAS. The principal objective of the project was to enhance the ability of SAS as a licensing tool for LFRs. This objective was to be accomplished through three tasks: 1) Enhance the ability of SAS to couple with external software; 2) Improve the underlying physics models in SAS, with priority given to models that are highly relevant to LFRs; 3) Extend the Verification and Validation (V&V) basis of the software

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Flexible Perovskite-Perovskite PV for Mobile Power Applications (Final Technical Report)

This is the final report for the referenced TCF award which ran from Oct. 2019 through Jan. 2024 in conjunction with the industry partner Swift Solar. The long duration of the program was due to several factors including the pandemic and a technical work stoppage due to changes in the scope. Additionally, Swift’s business focus shifted during the course of the program. As a result of these factors, this program underwent two distinct modifications that dramatically changed the work scope. The following report is organized into three separate sections, each of which addresses a distinct work scope. Those scope changes, what necessitated them, and any new tasks/milestones are given, briefly, at the top of each section. The work performed was research on the hybrid halide perovskites (HHP), both the absorber material itself as well as other material layers that are required in a full device stack. At the start of the period of performance, there were two distinct challenges that we sought to address: (1) a wide band gap absorber (>1.6 eV), and (2) a recombination layer for tandem devices that provided good sequestration of the individual cell absorber materials in their respective device layers. NREL had previously published, and patented, advancements in both of these areas and they were the focus of much of the work throughout the program.

14 SOLAR ENERGY↗

Business Opportunities in Clean Energy Supply Chains: Guidebook for Small and Medium-Sized Automotive Suppliers

This is the final report for the referenced TCF award which ran from Oct. 2019 through Jan. 2024 in conjunction with the industry partner Swift Solar. The long duration of the program was due to several factors including the pandemic and a technical work stoppage due to changes in the scope. Additionally, Swift’s business focus shifted during the course of the program. As a result of these factors, this program underwent two distinct modifications that dramatically changed the work scope. The following report is organized into three separate sections, each of which addresses a distinct work scope. Those scope changes, what necessitated them, and any new tasks/milestones are given, briefly, at the top of each section. The work performed was research on the hybrid halide perovskites (HHP), both the absorber material itself as well as other material layers that are required in a full device stack. At the start of the period of performance, there were two distinct challenges that we sought to address: (1) a wide band gap absorber (>1.6 eV), and (2) a recombination layer for tandem devices that provided good sequestration of the individual cell absorber materials in their respective device layers. NREL had previously published, and patented, advancements in both of these areas and they were the focus of much of the work throughout the program. The auto manufacturing space is evolving quickly. Sales of various electrified vehicles (xEVs) continue to grow steadily, which has medium to long-term ramifications for the thousands of U.S. manufacturers and hundreds of thousands of workers that contribute to the domestic automotive supply chain. In tandem with this growth in xEV sales, domestic clean energy manufacturing is surging (both for the xEV supply chain and other technologies), with public incentives spurring billions in private sector investment. Moreover, the next 2–3 years will see new and expanded industrial facilities come online to make products like hydrogen electrolyzers, solar panels, batteries, advanced electronics—and will create new supply chain needs and business opportunities as they do. DOE’s Office of Manufacturing and Energy Supply Chains (MESC) and Argonne National Laboratory developed this report to help automotive manufacturers—alongside various business support partners— understand these trends and their response options, and to make the most of current federal assistance programs for manufacturers. These market changes may create opportunities for small- and medium-sized manufacturers (SMMs) to expand production, grow profit margins, and diversify their businesses. For instance, SMMs could take advantage of engineering and process design similarities with new end-use industries that might enable greater business growth and stability as markets continue to change.

14 SOLAR ENERGY↗

TuFF internal WRAP for Rapid Pipeline Repair (TuFF iWRAP)

The goal of “TuFF internal WRAP for Rapid Pipeline Repair” (TuFF iWRAP) program was to develop a novel material system and placement process to fabricate structural pipe within the existing deteriorated pipelines without disruption of gas delivery. The team (University of Delaware – Center for Composite Materials (UD-CCM) and Plitzie Inc.) addressed this challenge by developing a new material feedstock and pipe in pipe (PIP) repair strategy. This allows the potential for significant cost reduction and has minimum operational impact on gas customers. The new robotic based placement design allows discontinuous placement of pipe sections creating a stand-alone structural liner within the legacy pipeline without the need for pipe shutdown. Here, the material is supplied using a tethered material feeding system and is placed and UV cured with the internal Wound Rapid Automated Placement (iWRAP) system. This provides maximum placement efficiency capable of traversing 90 angle bends in 12-inch pipe and overall design customization to meet pipe repair requirements (e.g., variable wall thickness, bridging gaps, etc.). UV-curable fiber reinforced composite material has been optimized to meet structural performance and placement/cure times. Superior strength and fatigue life has been demonstrated by improving fiber-matrix adhesion using new fiber sizing for UV resins. Rapid cure approaches using new liner and resins have been evaluated with industry. The appropriate design of the section joints has been developed and tested. We estimate coating time to be ~100 hours per mile enabling typical pipe repair within 1 week.

03 NATURAL GAS↗

Effect of high-temperature annealing on the microstructure and thermoelectric properties of GaP doped SiGe

Annealing of GaP doped SiGe will significantly alter the thermoelectric properties of the material resulting in increased performance as measured by the figure of merit Z and the power factor P. The microstructures and corresponding thermoelectric properties after annealing in the 1100 to 1300 C temperature range have been examined to correlate performance improvement with annealing history. The figure of merit and power factor were both improved by homogenizing the material and limiting the amount of cross-doping. Annealing at 1215 C for 100 hr resulted in the best combination of thermoelectric properties with a resultant figure of merit exceeding 1x10 to the -3 deg C to the -1 and a power factor of 44 microW/cm/deg C sq for the temperature range of interest for space power: 400 to 1000 C.

Draper, Susan L.↗

Shuttle Infrared Leeside Temperature Sensing (SILTS) experiment - STS 61-C results

The operation of the Shuttle Infrared Leeside Temperature Sensing experiment on mission STS 61-C of the Space Shuttle Orbiter Columbia is described. False-color video images are shown of surface temperatures on the leeside wing and fuselage areas during entry. Features evident in the imagery are related to aerodynamic flow phenomena such as shock interactions, leeside vortices, and elevon gap effects. Significant anomalies in experiment hardware operation occurred on this flight. The anomalous hardware performance resulted in requirements for major modification to the postflight data reduction procedures. The data collected provide a qualitative, but not a fully quantitative, look at leeside surface heating.

Throckmorton, David A.↗

Elevated temperature crack growth

Alloy 718 crack growth experiments were conducted to assess the ability of the selected path-independent (P-I) integrals to describe the elevated temperature crack growth behavior. These tests were performed on single edge notch (SEN) specimens under displacement control with multiple extensometers to monitor the specimen and crack mouth opening displacement (CMOD). The displacements in these tests were sufficiently high to induce bulk cyclic inelastic deformation of the specimen. Under these conditions, the linear elastic fracture mechanics (LEFM) parameter K does not correlate the crack growth data. The experimentally measured displacement gradients at the end of specimen gage length were used as the boundary conditions in elastic-plastic finite element method (FEM) analyses. These analyses were performed with a node release approach using CYANIDE, a GEAE FEM code, which included a gap element which is capable of efficiently simulating crack closure. Excellent correlation was obtained between the experimentally measured and predicted variation of stress and CMOD with crack length and the stress-CMOD loops for Alloy 718 tests conducted at 538 C. This confirmed the accuracy of the FEM crack growth simulation approach. The experimentally measured crack growth rate data correlated well the selected P-I integrals. These investigations have produced significant progress in developing P-I integrals as non-linear fracture mechanics parameters. The results suggest that this methodology has the potential of accurately describing elevated temperature crack growth behavior under the combined influence of thermal cycling and bulk elastic-inelastic deformation states.

Kim, K. S.↗

Using Transparent Informed Prefetching (TIP) to reduce file read latency

As processor performance gains continue to outstrip Input/Output gains, I/O performance is becoming critical to overall system performance. File read latency is the most significant bottleneck for high performance I/O. Other aspects of I/O performance benefit from recent advances in disk bandwidth and throughput resulting from disk arrays, and in write performance derived from buffered write behind and the Log-structured File System. The access gap problem limiting improvements in read latency is exacerbated by distributed file systems operating over networks with diverse bandwidth. Focus is on extending the power of caching and prefetching to reduce file read latencies by exploiting hints from high-levels of a system. Such Transparent Informed Prefetching, TIP, and its benefits are described. It is argued that hints that disclose high level knowledge are a means for transferring optimization information across, without violating, module boundaries. How TIP can be used to convert the high throughput of new technologies such as disk arrays and log-structured file systems into low latency for applications is discussed. Our preliminary experiments show reductions in wall - clock execution time of 13 percent and 20 percent for a multiple module compilation tool (make) accessing data on a local disk and remote Coda file server, respectively, and a reduction of 30 percent for a text search (grep) remotely accessing many small files.

Patterson, R. H.↗

Analysis of Automated Aircraft Conflict Resolution and Weather Avoidance

This paper describes an analysis of using trajectory-based automation to resolve both aircraft and weather constraints for near-term air traffic management decision making. The auto resolution algorithm developed and tested at NASA-Ames to resolve aircraft to aircraft conflicts has been modified to mitigate convective weather constraints. Modifications include adding information about the size of a gap between weather constraints to the routing solution. Routes that traverse gaps that are smaller than a specific size are not used. An evaluation of the performance of the modified autoresolver to resolve both conflicts with aircraft and weather was performed. Integration with the Center-TRACON Traffic Management System was completed to evaluate the effect of weather routing on schedule delays.

Love, John F.↗

In Situ Thermal Inspection of Automated Fiber Placement Operations for Tow and Ply Defect Detection

The advent of Automated Fiber Placement (AFP) systems have aided the rapid manufacturing of composite aerospace structures. One of the challenges that AFP systems pose is the uniformity of the deposited prepreg tape layers, which complicates detection of laps, gaps, overlaps and twists. The current detection method used in industry involves halting fabrication and performing a time consuming, visual inspection of each tape layer. Typical AFP systems use a quartz lamp to heat the base layer to make the surface tacky as it deposits another tape layer. The innovation proposed in this paper is to use the preheated base layer as a through-transmission heat source for inspecting the newly added tape layer in situ using a thermographic camera mounted on to the AFP hardware. Such a system would not only increase manufacturing throughput by reducing inspection times, but it would also aid in process development for new structural designs or material systems by providing data on as-built parts. To this end, a small thermal camera was mounted onto an AFP robotic research platform at NASA, and thermal data was collected during typical and experimental layup operations. The data was post processed to reveal defects such as tow overlap/gap, wrinkling, and peel-up. Defects that would have been impossible to detect visually were also discovered in the data, such as poor/loss of adhesion between plies and the effects of vacuum debulking. This paper will cover the results of our experiments, and the plans for future versions of this inspection system.

Juarez, Peter D.↗

Pretest Simulations of a Supersonic Mixing and Combustion Validation Experiment to Assess Sensitivities

The reliance on CFD simulations to develop, design, and optimize scramjet systems (or components) has become commonplace. This reliance inevitably hinges on the ability of the computational analyst to quantify the level of confidence in their computational results. Unfortunately, nearly all the measured data available for this assessment comes from antiquated experimental datasets, or from tests that focused on the extraction of scramjet system (or component) performance. The objective of a CFD validation experiment is to quantify the predictive accuracy of one or more of the CFD physics submodels, implying that other uncertainties related to replicating the facility flow environment (e.g., knowledge of boundary conditions) must be minimized to the extent possible. This inevitably places stringent requirements on the quality and quantity of measurements taken to accurately specify inflow, outflow, and surface conditions for the CFD simulations; in addition to the measurements taken for the validation of physics submodels. This places additional demands on the experimental process above and beyond those for test article performance assessment. A recent high speed code credibility workshop series sponsored by AFRL identified a gap in existing validation data for fundamental assessments of turbulent mixing and combustion CFD closure models at scramjet engine relevant conditions. To address this gap, engineers at AFRL have designed a coaxial jet flame configuration that will be tested at two facilities (Research Cell 19 at the Air Force Research Lab, and at Purdue University). The effort described here documents pretest simulations of this validation experiment with the goal of fleshing out the extent of the facility flowpath that must be included to adequately reproduce the facility test section flow environment. The findings indicate that the flow around the support structure for the fuel injection centerbody upstream of the facility nozzle generates disturbances that persist throughout the nozzle expansion process; corrupting the azimuthal symmetry that was desired in the fuel/air mixing region of the test section. Simulations without this support structure maintained a high degree of azimuthal symmetry up until the fuel injection plane. However, even in this scenario the azimuthal symmetry was not maintained once the centerbody boundary layer transitioned to a wake flow downstream of the fuel injection plane.

CFD↗

Pretest Simulations of a Supersonic Mixing and Combustion Validation Experiment to Assess Sensitivities

The reliance on CFD simulations to develop, design, and optimize scramjet systems (or components) has become commonplace. This reliance inevitably hinges on the ability of the computational analyst to quantify the level of confidence in their computational results. Unfortunately, nearly all the measured data available for this assessment comes from antiquated experimental datasets, or from tests that focused on the extraction of scramjet system (or component) performance. The objective of a CFD validation experiment is to quantify the predictive accuracy of one or more of the CFD physics submodels, implying that other uncertainties related to replicating the facility flow environment (e.g., knowledge of boundary conditions) must be minimized to the extent possible. This inevitably places stringent requirements on the quality and quantity of measurements taken to accurately specify inflow, outflow, and surface conditions for the CFD simulations; in addition to the measurements taken for the validation of physics submodels. This places additional demands on the experimental process above and beyond those for test article performance assessment. A recent high speed code credibility workshop series sponsored by AFRL identified a gap in existing validation data for fundamental assessments of turbulent mixing and combustion CFD closure models at scramjet engine relevant conditions. To address this gap, engineers at AFRL have designed a coaxial jet flame configuration that will be tested at two facilities (Research Cell 19 at the Air Force Research Lab, and at Purdue University). The effort described here documents pretest simulations of this validation experiment with the goal of fleshing out the extent of the facility flowpath that must be included to adequately reproduce the facility test section flow environment. The findings indicate that the flow around the support structure for the fuel injection centerbody upstream of the facility nozzle generates disturbances that persist throughout the nozzle expansion process; corrupting the azimuthal symmetry that was desired in the fuel/air mixing region of the test section. Simulations without this support structure maintained a high degree of azimuthal symmetry up until the fuel injection plane. However, even in this scenario the azimuthal symmetry was not maintained once the centerbody boundary layer transitioned to a wake flow downstream of the fuel injection plane.

CFD↗

Air bearing heat exchanger

The various technologies presented herein relate to fabrication and operation of a heat exchanger that is configured to extract heat from an underlying substrate. Heat can be extracted by way of an air gap formed between an impeller and a baseplate. By utilizing a pump to create an initial air gap that is further maintained by rotation of the impeller relative to the baseplate, a spring can be utilized that can apply a force of greater magnitude to the impeller than is used in a conventional approach, thus enabling the weight of the impeller to be negligible with respect to a width of the air gap, thereby conferring the desirable feature of orientation independence with respect to gravity with no performance degradation.

97 MATHEMATICS AND COMPUTING↗

Air bearing heat exchanger methods

The various technologies presented herein relate to fabrication and operation of a heat exchanger that is configured to extract heat from an underlying substrate. Heat can be extracted by way of an air gap formed between an impeller and a baseplate. By utilizing a pump to create an initial air gap that is further maintained by rotation of the impeller relative to the baseplate, a spring can be utilized that can apply a force of greater magnitude to the impeller than is used in a conventional approach, thus enabling the weight of the impeller to be negligible with respect to a width of the air gap, thereby conferring the desirable feature of orientation independence with respect to gravity with no performance degradation.

42 ENGINEERING↗

Using Machine Learning to Track Objects Across Cameras

Video surveillance is one of the most important technologies used by the International Atomic Energy Agency in international safeguards. At large, complicated facilities, multiple surveillance cameras are deployed to monitor the transfer of safeguards-relevant objects across the site. During inspections, all surveillance videos are reviewed to ensure the objects are not manipulated or diverted during transfer, a laborious, time-consuming task. This work describes using deep machine learning algorithms to track objects automatically across multiple cameras, greatly improving the efficiency of the review process. The fundamental problem in this object tracking task across multiple cameras is how to associate the same object, which may show extreme intra-class variations, such as viewpoints, occlusions, and various scales, in different and even non-overlapped cameras. Object re-identification (Re-ID) in nuclear facility video surveillance is even more challenging than classic person or vehicle Re-ID problems because different instances in the same category may display an identical appearance. One observation from nuclear facility surveillance videos is that all objects must be carted (e.g., via forklift) to move. Therefore, the spatial context information of an object, which provides the feature from the carrier, is critical for the object Re-ID task. This work proposes a two-stream convolutional neural networks model that takes features of objects and their surrounding regions into account. Moreover, the custom videos usually are gleaned from different scenes from the training data, which may have extreme variations in illumination changes and/or cluttered backgrounds. Directly applying the trained model to custom videos will dramatically decrease the performance. To tackle this problem, an advanced domain adaptation technique is proposed to mitigate the gap between the data taken from different scenes. The proposed framework will track objects of interest across a nuclear complex. The resulting tracks can be used in further analyses, such as event/activity recognition, anomaly detection, etc.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗

Buffer-IPyC separation process in TRISO fuel particles simulated with Bison code

During High Temperature Gas-cooled Reactor (HTGR) operation, tristructural isotropic (TRISO) coated-particle fuel undergoes irradiation-induced changes in morphology and thermomechanical properties. Experimental results from the Advanced Gas Reactor (AGR) Fuel Development and Qualification Program show, among other things, the mechanism of gap formation between the buffer and inner pyrolytic carbon (IPyC) layers, which could be explored further via computational simulations using the Bison code. Two simulation models were developed, the debonding restricted model, where no gap formation between buffer and IPyC layers is permitted, and the debonding enabled model, where the gap between those layers is created. The inputs of the simulated models are based on the irradiation conditions from the AGR-1 experiment. The research included simulations on spherical and aspherical fuel types. Under the specific temperatures and fluences of the AGR-1 irradiation experiment, and the Bison simulations, it was concluded that the most common scenario is a gap formation along the buffer-IPyC interface, while the least possible scenario is the situation where there is no gap formation at the buffer-IPyC junction. The computational results confirmed that the sphericity of the fuel influences the thickness of the gap that occurs at the buffer-IPyC junction, in a way that with increasing aspect ratio the gap thickness increases. The results obtained for spherical and aspherical fuel are nearly identical. Finally, performed simulations match conclusions observed from the AGR-1 experiment, which as such shows that the Bison code is a good computational method for simulating the TRISO fuel. Future simulations will include the validation of performed research and comparison of the results between Bison and PARFUME codes.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗